When neighbor suppression is enabled the bridge device might reply to
Neighbor Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the bridge device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alla Segal <allas@mellanox.com>
Tested-by: Alla Segal <allas@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allocating the spare nexthop group it should be tested for kzalloc()
returning NULL, instead the already used nexthop group (which cannot be
NULL at this point) had been tested so far.
Additionally, if kzalloc() fails, return ERR_PTR(-ENOMEM) instead of NULL.
Coverity-id: 1463885
Reported-by: Coverity <scan-admin@coverity.com>
Signed-off-by: Patrick Eigensatz <patrickeigensatz@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-06-01
Here's one last bluetooth-next pull request for 5.8, which I hope can
still be accepted.
- Enabled Wide-Band Speech (WBS) support for Qualcomm wcn3991
- Multiple fixes/imprvovements to Qualcomm-based devices
- Fix GAP/SEC/SEM/BI-10-C qualfication test case
- Added support for Broadcom BCM4350C5 device
- Several other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose replica reads through read_from_replica=balance and
read_from_replica=localize. The default is to read from primary
(read_from_replica=no).
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
OSD-side issues with reads from replica have been resolved in
Octopus. Reading from replica should be safe wrt. unstable or
uncommitted state now, so add support for balanced and localized
reads.
There are two cases when a read from replica can't be served:
- OSD may silently drop the request, expecting the client to
notice that the acting set has changed and resend via the usual
means (handled with t->used_replica)
- OSD may return EAGAIN, expecting the client to resend to the
primary, ignoring replica read flags (see handle_reply())
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Allow expressing client's location in terms of CRUSH hierarchy as
a set of (bucket type name, bucket name) pairs. The userspace syntax
"crush_location = key1=value1 key2=value2" is incompatible with mount
options and needed adaptation. Key-value pairs are separated by '|'
and we use ':' instead of '=' to separate keys from values. So for:
crush_location = host=foo rack=bar
one would write:
crush_location=host:foo|rack:bar
As in userspace, "multipath" locations are supported, so indicating
locality for parallel hierarchies is possible:
crush_location=rack:foo1|rack:foo2|datacenter:bar
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
These would be matched with the provided client location to calculate
the locality value.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Needed for the next commit and useful for ceph_pg_pool_info tree as
well. I'm leaving the asserting helper in for now, but we should look
at getting rid of it in the future.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Calculate the latency for OSD read requests. Add a new r_end_stamp
field to struct ceph_osd_request that will hold the time of that
the reply was received. Use that to calculate the RTT for each call,
and divide the sum of those by number of calls to get averate RTT.
Keep a tally of RTT for OSD writes and number of calls to track average
latency of OSD writes.
URL: https://tracker.ceph.com/issues/43215
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
-----BEGIN PGP SIGNATURE-----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=wdaG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Another week, another set of bug fixes:
1) Fix pskb_pull length in __xfrm_transport_prep(), from Xin Long.
2) Fix double xfrm_state put in esp{4,6}_gro_receive(), also from Xin
Long.
3) Re-arm discovery timer properly in mac80211 mesh code, from Linus
Lüssing.
4) Prevent buffer overflows in nf_conntrack_pptp debug code, from
Pablo Neira Ayuso.
5) Fix race in ktls code between tls_sw_recvmsg() and
tls_decrypt_done(), from Vinay Kumar Yadav.
6) Fix crashes on TCP fallback in MPTCP code, from Paolo Abeni.
7) More validation is necessary of untrusted GSO packets coming from
virtualization devices, from Willem de Bruijn.
8) Fix endianness of bnxt_en firmware message length accesses, from
Edwin Peer.
9) Fix infinite loop in sch_fq_pie, from Davide Caratti.
10) Fix lockdep splat in DSA by setting lockless TX in netdev features
for slave ports, from Vladimir Oltean.
11) Fix suspend/resume crashes in mlx5, from Mark Bloch.
12) Fix use after free in bpf fmod_ret, from Alexei Starovoitov.
13) ARP retransmit timer guard uses wrong offset, from Hongbin Liu.
14) Fix leak in inetdev_init(), from Yang Yingliang.
15) Don't try to use inet hash and unhash in l2tp code, results in
crashes. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
l2tp: add sk_family checks to l2tp_validate_socket
l2tp: do not use inet_hash()/inet_unhash()
net: qrtr: Allocate workqueue before kernel_bind
mptcp: remove msk from the token container at destruction time.
mptcp: fix race between MP_JOIN and close
mptcp: fix unblocking connect()
net/sched: act_ct: add nat mangle action only for NAT-conntrack
devinet: fix memleak in inetdev_init()
virtio_vsock: Fix race condition in virtio_transport_recv_pkt
drivers/net/ibmvnic: Update VNIC protocol version reporting
NFC: st21nfca: add missed kfree_skb() in an error path
neigh: fix ARP retransmit timer guard
bpf, selftests: Add a verifier test for assigning 32bit reg states to 64bit ones
bpf, selftests: Verifier bounds tests need to be updated
bpf: Fix a verifier issue when assigning 32bit reg states to 64bit ones
bpf: Fix use-after-free in fmod_ret check
net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()
net/mlx5e: Fix MLX5_TC_CT dependencies
net/mlx5e: Properly set default values when disabling adaptive moderation
net/mlx5e: Fix arch depending casting issue in FEC
...
The user ID value isn't actually much use - and leaks a kernel pointer or a
userspace value - so replace it with the call debug ID, which appears in trace
points.
Signed-off-by: David Howells <dhowells@redhat.com>
Map the EACCES error that is produced by some ICMP6 packets to EHOSTUNREACH
when we get them as EACCES has other meanings within a filesystem context.
Signed-off-by: David Howells <dhowells@redhat.com>
With some newer AKMs, the KCK and KEK are bigger, so allow that
if the driver advertises support for it. In addition, add a new
attribute for the AKM so we can use it for offloaded rekeying.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
[reword commit message]
Link: https://lore.kernel.org/r/20200528212237.5eb58b00a5d1.I61b09d77c4f382e8d58a05dcca78096e99a6bc15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a 6 GHz channel exists, then we can probably safely assume that
the device actually supports it, and then it should support most
bandwidths.
This will probably need to be extended to check the interface type
and then dig into the HE capabilities for that though, to have the
correct bandwidth check.
Link: https://lore.kernel.org/r/20200528213443.d4864ef52e92.I82f09b2b14a56413ce20376d09967fe954a033eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An AP supporting EMA (Enhanced Multi-BSSID advertisement) should set
bit 83 in the extended capabilities IE (9.4.2.26 in the 802.11ax D5 spec).
So the *3rd* bit of the 10th byte should be checked.
Also, in one place, the wrong byte was checked.
(cfg80211_find_ie returns a pointer to the beginning of the IE,
so the data really starts at ie[2], so the 10th byte
should be ie[12]. To avoid this confusion, use cfg80211_find_elem
instead).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Link: https://lore.kernel.org/r/20200528213443.4316121fa2a3.I9745582f8d41ad8e689dac0fefcd70b276d7c1ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP advertises inconsistent data, namely it has CCFS1 or CCFS2,
but doesn't advertise support for 160/80+80 bandwidth or "Extended NSS
BW Support", then we cannot use any MCSes in the the higher bandwidth.
Thus, avoid connecting with higher bandwidth since it's less efficient
that way.
Link: https://lore.kernel.org/r/20200528213443.0e55d40c3ccc.I6fd0b4708ebd087e5e46466c3e91f6efbcbef668@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These capabilities cover what would otherwise be transported
in HT/VHT capabilities, but only a subset thereof that is
actually needed on 6 GHz with HE already present. Expose the
capabilities to userspace, drivers are expected to set them
as using the 6 GHz band (currently) requires HE capability.
Link: https://lore.kernel.org/r/20200528213443.244cd5cb9db8.Icd8c773277a88c837e7e3af1d4d1013cc3b66543@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 6GHz band does not have regulatory approval yet, but things are
moving forward. However, that has led to a change in the channelization
of the 6GHz band which has been accepted in the 11ax specification. It
also fixes a missing MHZ_TO_KHZ() macro for 6GHz channels while at it.
This change is primarily thrown in to discuss how to deal with it.
I noticed ath11k adding 6G support with old channelization and ditto
for iw. It probably involves changes in hostapd as well.
Cc: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Cc: Jouni Malinen <jouni@w1.fi>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/edf07cdd-ad15-4012-3afd-d8b961a80b69@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot was able to trigger a crash after using an ISDN socket
and fool l2tp.
Fix this by making sure the UDP socket is of the proper family.
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x465/0x540 net/ipv4/udp_tunnel.c:78
Write of size 1 at addr ffff88808ed0c590 by task syz-executor.5/3018
CPU: 0 PID: 3018 Comm: syz-executor.5 Not tainted 5.7.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd3/0x413 mm/kasan/report.c:382
__kasan_report.cold+0x20/0x38 mm/kasan/report.c:511
kasan_report+0x33/0x50 mm/kasan/common.c:625
setup_udp_tunnel_sock+0x465/0x540 net/ipv4/udp_tunnel.c:78
l2tp_tunnel_register+0xb15/0xdd0 net/l2tp/l2tp_core.c:1523
l2tp_nl_cmd_tunnel_create+0x4b2/0xa60 net/l2tp/l2tp_netlink.c:249
genl_family_rcv_msg_doit net/netlink/genetlink.c:673 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:718 [inline]
genl_rcv_msg+0x627/0xdf0 net/netlink/genetlink.c:735
netlink_rcv_skb+0x15a/0x410 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:746
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x537/0x740 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x882/0xe10 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6e6/0x810 net/socket.c:2352
___sys_sendmsg+0x100/0x170 net/socket.c:2406
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2439
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
RIP: 0033:0x45ca29
Code: 0d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007effe76edc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004fe1c0 RCX: 000000000045ca29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000005
RBP: 000000000078bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 000000000000094e R14: 00000000004d5d00 R15: 00007effe76ee6d4
Allocated by task 3018:
save_stack+0x1b/0x40 mm/kasan/common.c:49
set_track mm/kasan/common.c:57 [inline]
__kasan_kmalloc mm/kasan/common.c:495 [inline]
__kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:468
__do_kmalloc mm/slab.c:3656 [inline]
__kmalloc+0x161/0x7a0 mm/slab.c:3665
kmalloc include/linux/slab.h:560 [inline]
sk_prot_alloc+0x223/0x2f0 net/core/sock.c:1612
sk_alloc+0x36/0x1100 net/core/sock.c:1666
data_sock_create drivers/isdn/mISDN/socket.c:600 [inline]
mISDN_sock_create+0x272/0x400 drivers/isdn/mISDN/socket.c:796
__sock_create+0x3cb/0x730 net/socket.c:1428
sock_create net/socket.c:1479 [inline]
__sys_socket+0xef/0x200 net/socket.c:1521
__do_sys_socket net/socket.c:1530 [inline]
__se_sys_socket net/socket.c:1528 [inline]
__x64_sys_socket+0x6f/0xb0 net/socket.c:1528
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
Freed by task 2484:
save_stack+0x1b/0x40 mm/kasan/common.c:49
set_track mm/kasan/common.c:57 [inline]
kasan_set_free_info mm/kasan/common.c:317 [inline]
__kasan_slab_free+0xf7/0x140 mm/kasan/common.c:456
__cache_free mm/slab.c:3426 [inline]
kfree+0x109/0x2b0 mm/slab.c:3757
kvfree+0x42/0x50 mm/util.c:603
__free_fdtable+0x2d/0x70 fs/file.c:31
put_files_struct fs/file.c:420 [inline]
put_files_struct+0x248/0x2e0 fs/file.c:413
exit_files+0x7e/0xa0 fs/file.c:445
do_exit+0xb04/0x2dd0 kernel/exit.c:791
do_group_exit+0x125/0x340 kernel/exit.c:894
get_signal+0x47b/0x24e0 kernel/signal.c:2739
do_signal+0x81/0x2240 arch/x86/kernel/signal.c:784
exit_to_usermode_loop+0x26c/0x360 arch/x86/entry/common.c:161
prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline]
syscall_return_slowpath arch/x86/entry/common.c:279 [inline]
do_syscall_64+0x6b1/0x7d0 arch/x86/entry/common.c:305
entry_SYSCALL_64_after_hwframe+0x49/0xb3
The buggy address belongs to the object at ffff88808ed0c000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1424 bytes inside of
2048-byte region [ffff88808ed0c000, ffff88808ed0c800)
The buggy address belongs to the page:
page:ffffea00023b4300 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0xfffe0000000200(slab)
raw: 00fffe0000000200 ffffea0002838208 ffffea00015ba288 ffff8880aa000e00
raw: 0000000000000000 ffff88808ed0c000 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808ed0c480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88808ed0c500: 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808ed0c580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88808ed0c600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88808ed0c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 6b9f34239b ("l2tp: fix races in tunnel creation")
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Cc: Guillaume Nault <gnault@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When token lookup on MP_JOIN 3rd ack fails, the server
socket closes with a reset the incoming child. Such socket
has the 'is_mptcp' flag set, but no msk socket associated
- due to the failed lookup.
While crafting the reset packet mptcp_established_options_mp()
will try to dereference the child's master socket, causing
a NULL ptr dereference.
This change addresses the issue with explicit fallback to
TCP in such error path.
Fixes: 729cd6436f ("mptcp: cope better with MP_JOIN failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the other fq-based qdiscs take advantage of skb->hash and doesn't
recompute it if it is already set, sch_cake does not.
This was a deliberate choice because sch_cake hashes various parts of the
packet header to support its advanced flow isolation modes. However,
foregoing the use of skb->hash entirely loses a few important benefits:
- When skb->hash is set by hardware, a few CPU cycles can be saved by not
hashing again in software.
- Tunnel encapsulations will generally preserve the value of skb->hash from
before the encapsulation, which allows flow-based qdiscs to distinguish
between flows even though the outer packet header no longer has flow
information.
It turns out that we can preserve these desirable properties in many cases,
while still supporting the advanced flow isolation properties of sch_cake.
This patch does so by reusing the skb->hash value as the flow_hash part of
the hashing procedure in cake_hash() only in the following conditions:
- If the skb->hash is marked as covering the flow headers (skb->l4_hash is
set)
AND
- NAT header rewriting is either disabled, or did not change any values
used for hashing. The latter is important to match local-origin packets
such as those of a tunnel endpoint.
The immediate motivation for fixing this was the recent patch to WireGuard
to preserve the skb->hash on encapsulation. As such, this is also what I
tested against; with this patch, added latency under load for competing
flows drops from ~8 ms to sub-1ms on an RRUL test over a WireGuard tunnel
going through a virtual link shaped to 1Gbps using sch_cake. This matches
the results we saw with a similar setup using sch_fq_codel when testing the
WireGuard patch.
Fixes: 046f6fd5da ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A null pointer dereference in qrtr_ns_data_ready() is seen if a client
opens a qrtr socket before qrtr_ns_init() can bind to the control port.
When the control port is bound, the ENETRESET error will be broadcasted
and clients will close their sockets. This results in DEL_CLIENT
packets being sent to the ns and qrtr_ns_data_ready() being called
without the workqueue being allocated.
Allocate the workqueue before setting sk_data_ready and binding to the
control port. This ensures that the work and workqueue structs are
allocated and initialized before qrtr_ns_data_ready can be called.
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Signed-off-by: Chris Lew <clew@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we remote the msk from the token container only
via mptcp_close(). The MPTCP master socket can be destroyed
also via other paths (e.g. if not yet accepted, when shutting
down the listener socket). When we hit the latter scenario,
dangling msk references are left into the token container,
leading to memory corruption and/or UaF.
This change addresses the issue by moving the token removal
into the msk destructor.
Fixes: 79c0949e9a ("mptcp: Add key generation and token tree")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a MP_JOIN subflow completes the 3whs while another
CPU is closing the master msk, we can hit the
following race:
CPU1 CPU2
close()
mptcp_close
subflow_syn_recv_sock
mptcp_token_get_sock
mptcp_finish_join
inet_sk_state_load
mptcp_token_destroy
inet_sk_state_store(TCP_CLOSE)
__mptcp_flush_join_list()
mptcp_sock_graft
list_add_tail
sk_common_release
sock_orphan()
<socket free>
The MP_JOIN socket will be leaked. Additionally we can hit
UaF for the msk 'struct socket' referenced via the 'conn'
field.
This change try to address the issue introducing some
synchronization between the MP_JOIN 3whs and mptcp_close
via the join_list spinlock. If we detect the msk is closing
the MP_JOIN socket is closed, too.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently unblocking connect() on MPTCP sockets fails frequently.
If mptcp_stream_connect() is invoked to complete a previously
attempted unblocking connection, it will still try to create
the first subflow via __mptcp_socket_create(). If the 3whs is
completed and the 'can_ack' flag is already set, the latter
will fail with -EINVAL.
This change addresses the issue checking for pending connect and
delegating the completion to the first subflow. Additionally
do msk addresses and sk_state changes only when needed.
Fixes: 2303f994b3 ("mptcp: Associate MPTCP context with TCP socket")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-fetch send buffer for the CDC validation message before entering the
send_lock. Without that the send call might fail with -EBUSY because
there are no free buffers and waiting for buffers is not possible under
send_lock.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently add nat mangle action with comparing invert and orig tuple.
It is better to check IPS_NAT_MASK flags first to avoid non necessary
memcmp for non-NAT conntrack.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7R3wcACgkQSD+KveBX
+j6/ZQf/QD39naPeImfLjemkRK9L+TKbS4nU6wpUwf1jC33Wdm4HhkhsWEnR6C4l
OwU/Pae3I9EtKP4gRE0W1o8h7zC9h4hY7+IKZOdyQ32iUY55PX/H25oqAiCj1NCM
xzWpXOTwK/vkqmkCedAd+YpNdYlbOhfycr+KVPSsvFdaPqjzfNO1PJcLsUbAbzrX
A+8pYdhUYTtx1N3YHJL5abLN6WzMAKxgwlm9GG8YCXACTJT6CBWWHGebVsC5TDUk
Lj5hJj38mI8/3dcu6vWP0kLGVfRZo0HS/gpPGxbKQFpP+1uBYaRENAQONxkY++6S
GDPix7ccvN+yNMlON893PC/Cogw3Yg==
=WaCJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-cleanup-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-cleanup-2020-05-29
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When devinet_sysctl_register() failed, the memory allocated
in neigh_parms_alloc() should be freed.
Fixes: 20e61da7ff ("ipv4: fail early when creating netdev named all or default")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When client on the host tries to connect(SOCK_STREAM, O_NONBLOCK) to the
server on the guest, there will be a panic on a ThunderX2 (armv8a server):
[ 463.718844] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 463.718848] Mem abort info:
[ 463.718849] ESR = 0x96000044
[ 463.718852] EC = 0x25: DABT (current EL), IL = 32 bits
[ 463.718853] SET = 0, FnV = 0
[ 463.718854] EA = 0, S1PTW = 0
[ 463.718855] Data abort info:
[ 463.718856] ISV = 0, ISS = 0x00000044
[ 463.718857] CM = 0, WnR = 1
[ 463.718859] user pgtable: 4k pages, 48-bit VAs, pgdp=0000008f6f6e9000
[ 463.718861] [0000000000000000] pgd=0000000000000000
[ 463.718866] Internal error: Oops: 96000044 [#1] SMP
[...]
[ 463.718977] CPU: 213 PID: 5040 Comm: vhost-5032 Tainted: G O 5.7.0-rc7+ #139
[ 463.718980] Hardware name: GIGABYTE R281-T91-00/MT91-FS1-00, BIOS F06 09/25/2018
[ 463.718982] pstate: 60400009 (nZCv daif +PAN -UAO)
[ 463.718995] pc : virtio_transport_recv_pkt+0x4c8/0xd40 [vmw_vsock_virtio_transport_common]
[ 463.718999] lr : virtio_transport_recv_pkt+0x1fc/0xd40 [vmw_vsock_virtio_transport_common]
[ 463.719000] sp : ffff80002dbe3c40
[...]
[ 463.719025] Call trace:
[ 463.719030] virtio_transport_recv_pkt+0x4c8/0xd40 [vmw_vsock_virtio_transport_common]
[ 463.719034] vhost_vsock_handle_tx_kick+0x360/0x408 [vhost_vsock]
[ 463.719041] vhost_worker+0x100/0x1a0 [vhost]
[ 463.719048] kthread+0x128/0x130
[ 463.719052] ret_from_fork+0x10/0x18
The race condition is as follows:
Task1 Task2
===== =====
__sock_release virtio_transport_recv_pkt
__vsock_release vsock_find_bound_socket (found sk)
lock_sock_nested
vsock_remove_sock
sock_orphan
sk_set_socket(sk, NULL)
sk->sk_shutdown = SHUTDOWN_MASK
...
release_sock
lock_sock
virtio_transport_recv_connecting
sk->sk_socket->state (panic!)
The root cause is that vsock_find_bound_socket can't hold the lock_sock,
so there is a small race window between vsock_find_bound_socket() and
lock_sock(). If __vsock_release() is running in another task,
sk->sk_socket will be set to NULL inadvertently.
This fixes it by checking sk->sk_shutdown(suggested by Stefano) after
lock_sock since sk->sk_shutdown is set to SHUTDOWN_MASK under the
protection of lock_sock_nested.
Signed-off-by: Jia He <justin.he@arm.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mpls_entry_encode() from net/mpls/internal.h to include/net/mpls.h
and make it available for other users. Specifically, hardware driver that
offload MPLS can benefit from that.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As of commit 98fa6271cf
("tcp: refactor setting the initial congestion window") this is called
only from tcp_input.c, so it can be static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot is reporting:
net/ethtool/cabletest.c:230:5: warning: no previous prototype for
Mark the function as static.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/tipc/msg.c: In function 'tipc_msg_append':
net/tipc/msg.c:215:24: warning:
variable 'prev' set but not used [-Wunused-but-set-variable]
commit 0a3e060f34 ("tipc: add test for Nagle algorithm effectiveness")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 19e16d220f ("neigh: support smaller retrans_time settting")
we add more accurate control for ARP and NS. But for ARP I forgot to
update the latest guard in neigh_timer_handler(), then the next
retransmit would be reset to jiffies + HZ/2 if we set the retrans_time
less than 500ms. Fix it by setting the time_before() check to HZ/100.
IPv6 does not have this issue.
Reported-by: Jianwen Ji <jiji@redhat.com>
Fixes: 19e16d220f ("neigh: support smaller retrans_time settting")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, our only tag_8021q user, sja1105, has the ability to restore
bridge VLANs on its own, so this logic is unnecessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-05-29
The following pull-request contains BPF updates for your *net* tree.
We've added 6 non-merge commits during the last 7 day(s) which contain
a total of 4 files changed, 55 insertions(+), 34 deletions(-).
The main changes are:
1) minor verifier fix for fmod_ret progs, from Alexei.
2) af_xdp overflow check, from Bjorn.
3) minor verifier fix for 32bit assignment, from John.
4) powerpc has non-overlapping addr space, from Petr.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No users left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP protocol allows to bind multiple address to a socket. That
feature is currently only exposed as a socket option. Add a bind_add
method struct proto that allows to bind additional addresses, and
switch the dlm code to use the method instead of going through the
socket option from kernel space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out a sctp_setsockopt_bindx_kernel that takes a kernel pointer
to the sockaddr and make sctp_setsockopt_bindx a small wrapper around
it. This prepares for adding a new bind_add proto op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-05-29
1) Several fixes for ESP gro/gso in transport and beet mode when
IPv6 extension headers are present. From Xin Long.
2) Fix a wrong comment on XFRMA_OFFLOAD_DEV.
From Antony Antony.
3) Fix sk_destruct callback handling on ESP in TCP encapsulation.
From Sabrina Dubroca.
4) Fix a use after free in xfrm_output_gso when used with vxlan.
From Xin Long.
5) Fix secpath handling of VTI when used wiuth IPCOMP.
From Xin Long.
6) Fix an oops when deleting a x-netns xfrm interface.
From Nicolas Dichtel.
7) Fix a possible warning on policy updates. We had a case where it was
possible to add two policies with the same lookup keys.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-05-29
1) Add IPv6 encapsulation support for ESP over UDP and TCP.
From Sabrina Dubroca.
2) Remove unneeded reference when initializing xfrm interfaces.
From Nicolas Dichtel.
3) Remove some indirect calls from the state_afinfo.
From Florian Westphal.
Please note that this pull request has two merge conflicts
between commit:
0c922a4850 ("xfrm: Always set XFRM_TRANSFORMED in xfrm{4,6}_output_finish")
from Linus' tree and commit:
2ab6096db2 ("xfrm: remove output_finish indirection from xfrm_state_afinfo")
from the ipsec-next tree.
and between commit:
3986912f6a ("ipv6: move SIOCADDRT and SIOCDELRT handling into ->compat_ioctl")
from the net-next tree and commit:
0146dca70b ("xfrm: add support for UDPv6 encapsulation of ESP")
from the ipsec-next tree.
Both conflicts can be resolved as done in linux-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a lockdep which led to commit
fad003b6c8 ("Bluetooth: Fix inconsistent lock state with RFCOMM")
Lockdep noticed that `sk->sk_lock.slock' was acquired without disabling
the softirq while the lock was also used in softirq context.
Unfortunately the solution back then was to disable interrupts before
acquiring the lock which however made lockdep happy.
It would have been enough to simply disable the softirq. Disabling
interrupts before acquiring a spinlock_t is not allowed on PREEMPT_RT
because these locks are converted to 'sleeping' spinlocks.
Use spin_lock_bh() in order to acquire the `sk_lock.slock'.
Reported-by: Luis Claudio R. Goncalves <lclaudio@uudg.org>
Reported-by: kbuild test robot <lkp@intel.com> [missing unlock]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is to fix a crash:
[ ] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ ] general protection fault: 0000 [#1] SMP KASAN PTI
[ ] RIP: 0010:ipv6_local_error+0xac/0x7a0
[ ] Call Trace:
[ ] xfrm6_local_error+0x1eb/0x300
[ ] xfrm_local_error+0x95/0x130
[ ] __xfrm6_output+0x65f/0xb50
[ ] xfrm6_output+0x106/0x46f
[ ] udp_tunnel6_xmit_skb+0x618/0xbf0 [ip6_udp_tunnel]
[ ] vxlan_xmit_one+0xbc6/0x2c60 [vxlan]
[ ] vxlan_xmit+0x6a0/0x4276 [vxlan]
[ ] dev_hard_start_xmit+0x165/0x820
[ ] __dev_queue_xmit+0x1ff0/0x2b90
[ ] ip_finish_output2+0xd3e/0x1480
[ ] ip_do_fragment+0x182d/0x2210
[ ] ip_output+0x1d0/0x510
[ ] ip_send_skb+0x37/0xa0
[ ] raw_sendmsg+0x1b4c/0x2b80
[ ] sock_sendmsg+0xc0/0x110
This occurred when sending a v4 skb over vxlan6 over ipsec, in which case
skb->protocol == htons(ETH_P_IPV6) while skb->sk->sk_family == AF_INET in
xfrm_local_error(). Then it will go to xfrm6_local_error() where it tries
to get ipv6 info from a ipv4 sk.
This issue was actually fixed by Commit 628e341f31 ("xfrm: make local
error reporting more robust"), but brought back by Commit 844d48746e
("xfrm: choose protocol family by skb protocol").
So to fix it, we should call xfrm6_local_error() only when skb->protocol
is htons(ETH_P_IPV6) and skb->sk->sk_family is AF_INET6.
Fixes: 844d48746e ("xfrm: choose protocol family by skb protocol")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
rpcb_getport_async() invokes rpcb_call_async(), which return the value
of rpc_run_task() to "child". Since rpc_run_task() is impossible to
return an ERR pointer, there is no need to add the IS_ERR() condition on
"child" here. So we need to remove it.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
gss_mech_register() calls svcauth_gss_register_pseudoflavor() for each
flavour, but gss_mech_unregister() does not call auth_domain_put().
This is unbalanced and makes it impossible to reload the module.
Change svcauth_gss_register_pseudoflavor() to return the registered
auth_domain, and save it for later release.
Cc: stable@vger.kernel.org (v2.6.12+)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There is no valid case for supporting duplicate pseudoflavor
registrations.
Currently the silent acceptance of such registrations is hiding a bug.
The rpcsec_gss_krb5 module registers 2 flavours but does not unregister
them, so if you load, unload, reload the module, it will happily
continue to use the old registration which now has pointers to the
memory were the module was originally loaded. This could lead to
unexpected results.
So disallow duplicate registrations.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Cc: stable@vger.kernel.org (v2.6.12+)
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The domain table should be empty at module unload. If it isn't there is
a bug somewhere. So check and report.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Make sure SCTP_ADDR_{MADE_PRIM,ADDED} are sent only for associations
that have been established.
These events are described in rfc6458#section-6.1
SCTP_PEER_ADDR_CHANGE:
This tag indicates that an address that is
part of an existing association has experienced a change of
state (e.g., a failure or return to service of the reachability
of an endpoint via a specific transport address).
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using kernel_setsockopt for the TIPC_IMPORTANCE option when we can
just use the internal helper. The only change needed is to pass a struct
sock instead of tipc_sock, which is private to socket.c
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the RXRPC_MIN_SECURITY_LEVEL sockopt from
kernel space without going through a fake uaccess.
Thanks to David Howells for the documentation updates.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_RECVPKTINFO sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_ADD_PREFERENCES sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_V6ONLY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_PKTINFO sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_MTU_DISCOVER sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com> [rxrpc bits]
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_FREEBIND sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_TOS sockopt from kernel space without
going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_KEEPCNT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_KEEPINTVL sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_KEEP_IDLE sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_USER_TIMEOUT sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_SYNCNT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_QUICKACK sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_NODELAY sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_CORK sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_REUSEPORT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_RCVBUFFORCE sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_KEEPALIVE sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly enable timestamps instead of setting the
SO_TIMESTAMP* sockopts from kernel space and going through a fake
uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_BINDTOIFINDEX sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_SNDTIMEO_NEW sockopt from kernel
space without going through a fake uaccess. The interface is
simplified to only pass the seconds value, as that is the only
thing needed at the moment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_PRIORITY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_LINGER sockopt from kernel space
with onoff set to true and a linger time of 0 without going through a
fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_REUSEADDR sockopt from kernel space
without going through a fake uaccess.
For this the iscsi target now has to formally depend on inet to avoid
a mostly theoretical compile failure. For actual operation it already
did depend on having ipv4 or ipv6 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make tcp_ld_RTO_revert() helper available to IPv6, and
implement RFC 6069 :
Quoting this RFC :
3. Connectivity Disruption Indication
For Internet Protocol version 6 (IPv6) [RFC2460], the counterpart of
the ICMP destination unreachable message of code 0 (net unreachable)
and of code 1 (host unreachable) is the ICMPv6 destination
unreachable message of code 0 (no route to destination) [RFC4443].
As with IPv4, a router should generate an ICMPv6 destination
unreachable message of code 0 in response to a packet that cannot be
delivered to its destination address because it lacks a matching
entry in its routing table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Uninitialized when used in __nf_conntrack_update(), from
Nathan Chancellor.
2) Comparison of unsigned expression in nf_confirm_cthelper().
3) Remove 'const' type qualifier with no effect.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TX status reporting for the control port
TX API; this will be used by hostapd when it moves to the
control port TX API.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200527160334.19224-1-markus.theil@tu-ilmenau.de
[fix commit message, it was referring to nl80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Be there a platform with the following layout:
Regular NIC
|
+----> DSA master for switch port
|
+----> DSA master for another switch port
After changing DSA back to static lockdep class keys in commit
1a33e10e4a ("net: partially revert dynamic lockdep key changes"), this
kernel splat can be seen:
[ 13.361198] ============================================
[ 13.366524] WARNING: possible recursive locking detected
[ 13.371851] 5.7.0-rc4-02121-gc32a05ecd7af-dirty #988 Not tainted
[ 13.377874] --------------------------------------------
[ 13.383201] swapper/0/0 is trying to acquire lock:
[ 13.388004] ffff0000668ff298 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[ 13.397879]
[ 13.397879] but task is already holding lock:
[ 13.403727] ffff0000661a1698 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[ 13.413593]
[ 13.413593] other info that might help us debug this:
[ 13.420140] Possible unsafe locking scenario:
[ 13.420140]
[ 13.426075] CPU0
[ 13.428523] ----
[ 13.430969] lock(&dsa_slave_netdev_xmit_lock_key);
[ 13.435946] lock(&dsa_slave_netdev_xmit_lock_key);
[ 13.440924]
[ 13.440924] *** DEADLOCK ***
[ 13.440924]
[ 13.446860] May be due to missing lock nesting notation
[ 13.446860]
[ 13.453668] 6 locks held by swapper/0/0:
[ 13.457598] #0: ffff800010003de0 ((&idev->mc_ifc_timer)){+.-.}-{0:0}, at: call_timer_fn+0x0/0x400
[ 13.466593] #1: ffffd4d3fb478700 (rcu_read_lock){....}-{1:2}, at: mld_sendpack+0x0/0x560
[ 13.474803] #2: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: ip6_finish_output2+0x64/0xb10
[ 13.483886] #3: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x6c/0xbe0
[ 13.492793] #4: ffff0000661a1698 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[ 13.503094] #5: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x6c/0xbe0
[ 13.512000]
[ 13.512000] stack backtrace:
[ 13.516369] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc4-02121-gc32a05ecd7af-dirty #988
[ 13.530421] Call trace:
[ 13.532871] dump_backtrace+0x0/0x1d8
[ 13.536539] show_stack+0x24/0x30
[ 13.539862] dump_stack+0xe8/0x150
[ 13.543271] __lock_acquire+0x1030/0x1678
[ 13.547290] lock_acquire+0xf8/0x458
[ 13.550873] _raw_spin_lock+0x44/0x58
[ 13.554543] __dev_queue_xmit+0x84c/0xbe0
[ 13.558562] dev_queue_xmit+0x24/0x30
[ 13.562232] dsa_slave_xmit+0xe0/0x128
[ 13.565988] dev_hard_start_xmit+0xf4/0x448
[ 13.570182] __dev_queue_xmit+0x808/0xbe0
[ 13.574200] dev_queue_xmit+0x24/0x30
[ 13.577869] neigh_resolve_output+0x15c/0x220
[ 13.582237] ip6_finish_output2+0x244/0xb10
[ 13.586430] __ip6_finish_output+0x1dc/0x298
[ 13.590709] ip6_output+0x84/0x358
[ 13.594116] mld_sendpack+0x2bc/0x560
[ 13.597786] mld_ifc_timer_expire+0x210/0x390
[ 13.602153] call_timer_fn+0xcc/0x400
[ 13.605822] run_timer_softirq+0x588/0x6e0
[ 13.609927] __do_softirq+0x118/0x590
[ 13.613597] irq_exit+0x13c/0x148
[ 13.616918] __handle_domain_irq+0x6c/0xc0
[ 13.621023] gic_handle_irq+0x6c/0x160
[ 13.624779] el1_irq+0xbc/0x180
[ 13.627927] cpuidle_enter_state+0xb4/0x4d0
[ 13.632120] cpuidle_enter+0x3c/0x50
[ 13.635703] call_cpuidle+0x44/0x78
[ 13.639199] do_idle+0x228/0x2c8
[ 13.642433] cpu_startup_entry+0x2c/0x48
[ 13.646363] rest_init+0x1ac/0x280
[ 13.649773] arch_call_rest_init+0x14/0x1c
[ 13.653878] start_kernel+0x490/0x4bc
Lockdep keys themselves were added in commit ab92d68fc2 ("net: core:
add generic lockdep keys"), and it's very likely that this splat existed
since then, but I have no real way to check, since this stacked platform
wasn't supported by mainline back then.
>From Taehee's own words:
This patch was considered that all stackable devices have LLTX flag.
But the dsa doesn't have LLTX, so this splat happened.
After this patch, dsa shares the same lockdep class key.
On the nested dsa interface architecture, which you illustrated,
the same lockdep class key will be used in __dev_queue_xmit() because
dsa doesn't have LLTX.
So that lockdep detects deadlock because the same lockdep class key is
used recursively although actually the different locks are used.
There are some ways to fix this problem.
1. using NETIF_F_LLTX flag.
If possible, using the LLTX flag is a very clear way for it.
But I'm so sorry I don't know whether the dsa could have LLTX or not.
2. using dynamic lockdep again.
It means that each interface uses a separate lockdep class key.
So, lockdep will not detect recursive locking.
But this way has a problem that it could consume lockdep class key
too many.
Currently, lockdep can have 8192 lockdep class keys.
- you can see this number with the following command.
cat /proc/lockdep_stats
lock-classes: 1251 [max: 8192]
...
The [max: 8192] means that the maximum number of lockdep class keys.
If too many lockdep class keys are registered, lockdep stops to work.
So, using a dynamic(separated) lockdep class key should be considered
carefully.
In addition, updating lockdep class key routine might have to be existing.
(lockdep_register_key(), lockdep_set_class(), lockdep_unregister_key())
3. Using lockdep subclass.
A lockdep class key could have 8 subclasses.
The different subclass is considered different locks by lockdep
infrastructure.
But "lock-classes" is not counted by subclasses.
So, it could avoid stopping lockdep infrastructure by an overflow of
lockdep class keys.
This approach should also have an updating lockdep class key routine.
(lockdep_set_subclass())
4. Using nonvalidate lockdep class key.
The lockdep infrastructure supports nonvalidate lockdep class key type.
It means this lockdep is not validated by lockdep infrastructure.
So, the splat will not happen but lockdep couldn't detect real deadlock
case because lockdep really doesn't validate it.
I think this should be used for really special cases.
(lockdep_set_novalidate_class())
Further discussion here:
https://patchwork.ozlabs.org/project/netdev/patch/20200503052220.4536-2-xiyou.wangcong@gmail.com/
There appears to be no negative side-effect to declaring lockless TX for
the DSA virtual interfaces, which means they handle their own locking.
So that's what we do to make the splat go away.
Patch tested in a wide variety of cases: unicast, multicast, PTP, etc.
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Suggested-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
change typo in function name "nofity" to "notify"
sctp_ulpevent_nofity_peer_addr_change ->
sctp_ulpevent_notify_peer_addr_change
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a field to the tls rx offload context which enables
drivers to force a send_resync call.
This field can be used by drivers to request a resync at the next
possible tls record. It is beneficial for hardware that provides the
resync sequence number asynchronously. In such cases, the packet that
triggered the resync does not contain the information required for a
resync. Instead, the driver requests resync for all the following
TLS record until the asynchronous notification with the resync request
TCP sequence arrives.
A following series for mlx5e ConnectX-6DX TLS RX offload support will
use this mechanism.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting old qdisc on dev_queue->qdisc_sleeping in
dev_qdisc_reset() is redundant, because this qdisc,
even if not same with dev_queue->qdisc, is reset via
qdisc_put() right after calling dev_graft_qdisc() when
hitting refcnt 0.
This is very easy to observe with qdisc_reset() tracepoint
and stack traces.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Tested-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for sch_mq and sch_mqprio, each dev queue points to the
same root qdisc, so when we reset the dev queues with
netdev_for_each_tx_queue() we end up resetting the same instance
of the root qdisc for multiple times.
Avoid this by checking the __QDISC_STATE_DEACTIVATED bit in
each iteration, so for sch_mq/sch_mqprio, we still reset all
of them like before, for the rest, we only reset it once.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Tested-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_destroy() calls ops->reset() and cleans up qdisc->gso_skb
and qdisc->skb_bad_txq, these are nearly same with qdisc_reset(),
so just call it directly, and cosolidate the code for the next
patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This essentially reverts 4d1a2d9ec1 ("Revert Backoff [v3]:
Rename skb to icmp_skb in tcp_v4_err()")
Now we have tcp_ld_RTO_revert() helper, we can use the usual
name for sk_buff parameter, so that tcp_v4_err() and
tcp_v6_err() use similar names.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6069 logic has been implemented for IPv4 only so far,
right in the middle of tcp_v4_err() and was error prone.
Move this code to one helper, to make tcp_v4_err() more
readable and to eventually expand RFC 6069 to IPv6 in
the future.
Also perform sock_owned_by_user() check a bit sooner.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On device updates, the hooknum and priority attributes are not required.
This patch makes optional these two netlink attributes.
Moreover, bail out with EOPNOTSUPP if userspace tries to update the
hooknum and priority for existing flowtables.
While at this, turn EINVAL into EOPNOTSUPP in case the hooknum is not
ingress. EINVAL is reserved for missing netlink attribute / malformed
netlink messages.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A flowtable might be composed of dynamic interfaces only. Such dynamic
interfaces might show up at a later stage. This patch allows users to
register a flowtable with no devices. Once the dynamic interface becomes
available, the user adds the dynamic devices to the flowtable.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Update the flowtable netlink notifier to take the list of hooks as input.
This allows to reuse this function in incremental flowtable hook updates.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Update nft_flowtable_parse_hook() to take the flowtable hook list as
parameter. This allows to reuse this function to update the hooks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conntrack dump does not support kernel side filtering (only get exists,
but it returns only one entry. And user has to give a full valid tuple)
It means that userspace has to implement filtering after receiving many
irrelevant entries, consuming resources (conntrack table is sometimes
very huge, much more than a routing table for example).
This patch adds filtering in kernel side. To achieve this goal, we:
* Add a new CTA_FILTER netlink attributes, actually a flag list to
parametize filtering
* Convert some *nlattr_to_tuple() functions, to allow a partial parsing
of CTA_TUPLE_ORIG and CTA_TUPLE_REPLY (so nf_conntrack_tuple it not
fully set)
Filtering is now possible on:
* IP SRC/DST values
* Ports for TCP and UDP flows
* IMCP(v6) codes types and IDs
Filtering is done as an "AND" operator. For example, when flags
PROTO_SRC_PORT, PROTO_NUM and IP_SRC are sets, only entries matching all
values are dumped.
Changes since v1:
Set NLM_F_DUMP_FILTERED in nlm flags if entries are filtered
Changes since v2:
Move several constants to nf_internals.h
Move a fix on netlink values check in a separate patch
Add a check on not-supported flags
Return EOPNOTSUPP if CDA_FILTER is set in ctnetlink_flush_conntrack
(not yet implemented)
Code style issues
Changes since v3:
Fix compilation warning reported by kbuild test robot
Changes since v4:
Fix a regression introduced in v3 (returned EINVAL for valid netlink
messages without CTA_MARK)
Changes since v5:
Change definition of CTA_FILTER_F_ALL
Fix a regression when CTA_TUPLE_ZONE is not set
Signed-off-by: Romain Bellan <romain.bellan@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IBTA declares "vendor option not supported" reject reason in REJ messages
if passive side doesn't want to accept proposed ECE options.
Due to the fact that ECE is managed by userspace, there is a need to let
users to provide such rejected reason.
Link: https://lore.kernel.org/r/20200526103304.196371-7-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Clang-10 and clang-11 run into a corner case of the register
allocator on 32-bit ARM, leading to excessive stack usage from
register spilling:
net/bridge/br_multicast.c:2422:6: error: stack frame size of 1472 bytes in function 'br_multicast_get_stats' [-Werror,-Wframe-larger-than=]
Work around this by marking one of the internal functions as
noinline_for_stack.
Link: https://bugs.llvm.org/show_bug.cgi?id=45802#c9
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the MRP netlink interface. Before, each attribute
represented a binary structure which made it hard to be extended.
Therefore update the MRP netlink interface such that each existing
attribute to be a nested attribute which contains the fields of the
binary structures.
In this way the MRP netlink interface can be extended without breaking
the backwards compatibility. It is also using strict checking for
attributes under the MRP top attribute.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
net/ipv4/nexthop.c:841:30: warning: implicit conversion from enumeration
type 'enum nexthop_event_type' to different enumeration type 'enum
fib_event_type' [-Wenum-conversion]
call_nexthop_notifiers(net, NEXTHOP_EVENT_DEL, nh);
~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~
1 warning generated.
Use the right type for event_type so that clang does not warn.
Fixes: 8590ceedb7 ("nexthop: add support for notifiers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1038
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The accept(2) is an "input" socket interface, so we should use
SO_RCVTIMEO instead of SO_SNDTIMEO to set the timeout.
So this patch replace sock_sndtimeo() with sock_rcvtimeo() to
use the right timeout in the vsock_accept().
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one issues in 'rpc_ntop6':
- 'snprintf' returns the number of characters which would have been
written if enough space had been available, excluding the terminating
null byte. Thus, a return value of 'sizeof(scopebuf)' means that the
last character was dropped.
- 'strcat' adds a terminating null byte to the string, thus if len ==
buflen, the null byte is written past the end of the buffer.
Signed-off-by: Fedor Tokarev <ftokarev@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
>> include/linux/netfilter/nf_conntrack_pptp.h:13:20: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
extern const char *const pptp_msg_name(u_int16_t msg);
^~~~~~
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 4c559f15ef ("netfilter: nf_conntrack_pptp: prevent buffer overflows in debug code")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net/netfilter/nf_conntrack_core.c: In function nf_confirm_cthelper:
net/netfilter/nf_conntrack_core.c:2117:15: warning: comparison of unsigned expression in < 0 is always false [-Wtype-limits]
2117 | if (protoff < 0 || (frag_off & htons(~0x7)) != 0)
| ^
ipv6_skip_exthdr() returns a signed integer.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 703acd70f2 ("netfilter: nfnetlink_cthelper: unbreak userspace helper support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Clang warns:
net/netfilter/nf_conntrack_core.c:2068:21: warning: variable 'ctinfo' is
uninitialized when used here [-Wuninitialized]
nf_ct_set(skb, ct, ctinfo);
^~~~~~
net/netfilter/nf_conntrack_core.c:2024:2: note: variable 'ctinfo' is
declared here
enum ip_conntrack_info ctinfo;
^
1 warning generated.
nf_conntrack_update was split up into nf_conntrack_update and
__nf_conntrack_update, where the assignment of ctinfo is in
nf_conntrack_update but it is used in __nf_conntrack_update.
Pass the value of ctinfo from nf_conntrack_update to
__nf_conntrack_update so that uninitialized memory is not used
and everything works properly.
Fixes: ee04805ff5 ("netfilter: conntrack: make conntrack userspace helpers work again")
Link: https://github.com/ClangBuiltLinux/linux/issues/1039
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
OSD client should ignore cache/overlay flag if got redirect reply.
Otherwise, the client hangs when the cache tier is in forward mode.
[ idryomov: Redirects are effectively deprecated and no longer
used or tested. The original tiering modes based on redirects
are inherently flawed because redirects can race and reorder,
potentially resulting in data corruption. The new proxy and
readproxy tiering modes should be used instead of forward and
readforward. Still marking for stable as obviously correct,
though. ]
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/23296
URL: https://tracker.ceph.com/issues/36406
Signed-off-by: Jerry Lee <leisurelysw24@gmail.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
If we receive management frames with an HT-Control field, we cannot
parse them properly, as we assume a fixed length management header.
Since we don't even need the HTC field (for these frames, or really
at all), just remove it at the beginning of RX.
Reported-by: Haggai Abramovsky <haggai.abramovsky@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200526143346.cf5ce70521c5.I333251a084ec4cfe67b7ef7efe2d2f1a33883931@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Back with commit c8c240e284 (cfg80211: reg: remove support for
built-in regdb, 2015-10-15), support for using CFG80211_INTERNAL_REGDB
was removed in favor of loading the regulatory database as firmware
file. The documentation of CFG80211_CRDA_SUPPORT was not adjusted,
though, which is why it still mentions mentions the old way of loading
via the internal regulatory database.
Remove it so that the kernel option only mentions using the firmware
file.
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Link: https://lore.kernel.org/r/c56e60207fbd0512029de8c6276ee00f73491924.1589732954.git.ps@pks.im
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID Tx Rate configuration
through NL80211_TID_CONFIG_ATTR_TX_RATE* attributes. And it uses
nl80211_parse_tx_bitrate_mask api to validate the Tx rate mask.
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1589357504-10175-1-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As discussed with Mathy almost two years ago in
http://lore.kernel.org/r/20180806224857.14853-1-Mathy.Vanhoef@cs.kuleuven.be
we should let userspace process SA-QUERY frames if it
wants to, so that it can handle OCV (operating channel
validation) which mac80211 doesn't know how to.
Evidently I had been expecting Mathy to (re)send such a
patch, but he never did, perhaps expecting me to do it
after our discussion.
In any case, this came up now with OCV getting more
attention, so move the code around as discussed there
to let userspace handle it, and do it properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200526103131.1f9cf7e5b6db.Iae5b42b09ad2b1cbcbe13492002c43f0d1d51dfc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the necessary capabilities in nl80211 to allow drivers to
assign a cookie to control port TX frames (returned via extack in
the netlink ACK message of the command) and then later report the
frame's status.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200508144202.7678-2-markus.theil@tu-ilmenau.de
[use extack cookie instead of explicit message, recombine patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185907.GA15102@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507183909.GA12993@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises NL80211_EXT_FEATURE_SCAN_FREQ_KHZ
userspace can omit NL80211_ATTR_SCAN_FREQUENCIES in favor
of an NL80211_ATTR_SCAN_FREQ_KHZ. To get scan results in
KHz userspace must also set the
NL80211_SCAN_FLAG_FREQ_KHZ.
This lets nl80211 remain compatible with older userspaces
while not requring and sending redundant (and potentially
incorrect) scan frequency sets.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-4-thomas@adapt-ip.com
[use just nla_nest_start() (not _noflag) for NL80211_ATTR_SCAN_FREQ_KHZ]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 recently gained the ability to understand a
frequency offset component in KHz. Expose this in nl80211
through the new attributes NL80211_ATTR_WIPHY_FREQ_OFFSET,
NL80211_FREQUENCY_ATTR_OFFSET,
NL80211_ATTR_CENTER_FREQ1_OFFSET, and
NL80211_BSS_FREQUENCY_OFFSET.
These add support to send and receive a KHz offset
component with the following NL80211 commands:
- NL80211_CMD_FRAME
- NL80211_CMD_GET_SCAN
- NL80211_CMD_AUTHENTICATE
- NL80211_CMD_ASSOCIATE
- NL80211_CMD_CONNECT
Along with any other command which takes a chandef, ie:
- NL80211_CMD_SET_CHANNEL
- NL80211_CMD_SET_WIPHY
- NL80211_CMD_START_AP
- NL80211_CMD_RADAR_DETECT
- NL80211_CMD_NOTIFY_RADAR
- NL80211_CMD_CHANNEL_SWITCH
- NL80211_JOIN_IBSS
- NL80211_CMD_REMAIN_ON_CHANNEL
- NL80211_CMD_JOIN_OCB
- NL80211_CMD_JOIN_MESH
- NL80211_CMD_TDLS_CHANNEL_SWITCH
If the driver advertises a band containing channels with
frequency offset, it must also verify support for
frequency offset channels in its cfg80211 ops, or return
an error.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.
This doesn't actually change the nl80211 API yet.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
drop trace point name changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current rule for applying TID configuration for specific peer looks overly
complicated. No need to reject new TID configuration when override flag is
specified. Another call with the same TID configuration, but without
override flag, allows to apply new configuration anyway.
Use the same approach as for the 'all peers' case: if override flag is
specified, then reset existing TID configuration and immediately
apply a new one.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-5-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'handeled' to 'handled' in the Kconfig help for SCTP.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can try to coalesce skbs we take from the subflows rx queue with the
tail of the mptcp rx queue.
If successful, the skb head can be discarded early.
We can also free the skb extensions, we do not access them after this.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink policies are generally declared as const.
This is safer and prevents potential bugs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the last path, need to fix fib_info_nh_uses_dev for
external nexthops to avoid referencing multiple nh_grp structs.
Move the device check in fib_info_nh_uses_dev to a helper and
create a nexthop version that is called if the fib_info uses an
external nexthop.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIB lookups can return an entry that references an external nexthop.
While walking the nexthop struct we do not want to make multiple calls
into the nexthop code which can result in 2 different structs getting
accessed - one returning the number of paths the rest of the loop
seeing a different nh_grp struct. If the nexthop group shrunk, the
result is an attempt to access a fib_nh_common that does not exist for
the new nh_grp struct but did for the old one.
To fix that move the device evaluation code to a helper that can be
used for inline fib_nh path as well as external nexthops.
Update the existing check for fi->nh in fib_table_lookup to call a
new helper, nexthop_get_nhc_lookup, which walks the external nexthop
with a single rcu dereference.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must avoid modifying published nexthop groups while they might be
in use, otherwise we might see NULL ptr dereferences. In order to do
that we allocate 2 nexthoup group structures upon nexthop creation
and swap between them when we have to delete an entry. The reason is
that we can't fail nexthop group removal, so we can't handle allocation
failure thus we move the extra allocation on creation where we can
safely fail and return ENOMEM.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move nh_grp dereference and check for removing nexthop group due to
all members gone into remove_nh_grp_entry.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With struct flow_dissector_key_mpls now recording the first
FLOW_DIS_MPLS_MAX labels, we can extend Flower to filter on any of
these LSEs independently.
In order to avoid creating new netlink attributes for every possible
depth, let's define a new TCA_FLOWER_KEY_MPLS_OPTS nested attribute
that contains the list of LSEs to match. Each LSE is represented by
another attribute, TCA_FLOWER_KEY_MPLS_OPTS_LSE, which then contains
the attributes representing the depth and the MPLS fields to match at
this depth (label, TTL, etc.).
For each MPLS field, the mask is always set to all-ones, as this is
what the original API did. We could allow user configurable masks in
the future if there is demand for more flexibility.
The new API also allows to only specify an LSE depth. In that case,
Flower only verifies that the MPLS label stack depth is greater or
equal to the provided depth (that is, an LSE exists at this depth).
Filters that only match on one (or more) fields of the first LSE are
dumped using the old netlink attributes, to avoid confusing user space
programs that don't understand the new API.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current MPLS dissector only parses the first MPLS Label Stack
Entry (second LSE can be parsed too, but only to set a key_id).
This patch adds the possibility to parse several LSEs by making
__skb_flow_dissect_mpls() return FLOW_DISSECT_RET_PROTO_AGAIN as long
as the Bottom Of Stack bit hasn't been seen, up to a maximum of
FLOW_DIS_MPLS_MAX entries.
FLOW_DIS_MPLS_MAX is arbitrarily set to 7. This should be enough for
many practical purposes, without wasting too much space.
To record the parsed values, flow_dissector_key_mpls is modified to
store an array of stack entries, instead of just the values of the
first one. A bit field, "used_lses", is also added to keep track of
the LSEs that have been set. The objective is to avoid defining a
new FLOW_DISSECTOR_KEY_MPLS_XX for each level of the MPLS stack.
TC flower is adapted for the new struct flow_dissector_key_mpls layout.
Matching on several MPLS Label Stack Entries will be added in the next
patch.
The NFP and MLX5 drivers are also adapted: nfp_flower_compile_mac() and
mlx5's parse_tunnel() now verify that the rule only uses the first LSE
and fail if it doesn't.
Finally, the behaviour of the FLOW_DISSECTOR_KEY_MPLS_ENTROPY key is
slightly modified. Instead of recording the first Entropy Label, it
now records the last one. This shouldn't have any consequences since
there doesn't seem to have any user of FLOW_DISSECTOR_KEY_MPLS_ENTROPY
in the tree. We'd probably better do a hash of all parsed MPLS labels
instead (excluding reserved labels) anyway. That'd give better entropy
and would probably also simplify the code. But that's not the purpose
of this patch, so I'm keeping that as a future possible improvement.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix revert dynamic lockdep key changes for batman-adv,
by Sven Eckelmann
- use rcu_replace_pointer() where appropriate, by Antonio Quartulli
- Revert "disable ethtool link speed detection when auto negotiation
off", by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=vDHL
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20200526' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- Fix revert dynamic lockdep key changes for batman-adv,
by Sven Eckelmann
- use rcu_replace_pointer() where appropriate, by Antonio Quartulli
- Revert "disable ethtool link speed detection when auto negotiation
off", by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When streaming in Nagle mode, we try to bundle small messages from user
as many as possible if there is one outstanding buffer, i.e. not ACK-ed
by the receiving side, which helps boost up the overall throughput. So,
the algorithm's effectiveness really depends on when Nagle ACK comes or
what the specific network latency (RTT) is, compared to the user's
message sending rate.
In a bad case, the user's sending rate is low or the network latency is
small, there will not be many bundles, so making a Nagle ACK or waiting
for it is not meaningful.
For example: a user sends its messages every 100ms and the RTT is 50ms,
then for each messages, we require one Nagle ACK but then there is only
one user message sent without any bundles.
In a better case, even if we have a few bundles (e.g. the RTT = 300ms),
but now the user sends messages in medium size, then there will not be
any difference at all, that says 3 x 1000-byte data messages if bundled
will still result in 3 bundles with MTU = 1500.
When Nagle is ineffective, the delay in user message sending is clearly
wasted instead of sending directly.
Besides, adding Nagle ACKs will consume some processor load on both the
sending and receiving sides.
This commit adds a test on the effectiveness of the Nagle algorithm for
an individual connection in the network on which it actually runs.
Particularly, upon receipt of a Nagle ACK we will compare the number of
bundles in the backlog queue to the number of user messages which would
be sent directly without Nagle. If the ratio is good (e.g. >= 2), Nagle
mode will be kept for further message sending. Otherwise, we will leave
Nagle and put a 'penalty' on the connection, so it will have to spend
more 'one-way' messages before being able to re-enter Nagle.
In addition, the 'ack-required' bit is only set when really needed that
the number of Nagle ACKs will be reduced during Nagle mode.
Testing with benchmark showed that with the patch, there was not much
difference in throughput for small messages since the tool continuously
sends messages without a break, so Nagle would still take in effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enables dumping the statistics of a broadcast-receiver link
like the traditional 'broadcast-link' one (which is for broadcast-
sender). The link dumping can be triggered via netlink (e.g. the
iproute2/tipc tool) by the link flag - 'TIPC_NLA_LINK_BROADCAST' as the
indicator.
The name of a broadcast-receiver link of a specific peer will be in the
format: 'broadcast-link:<peer-id>'.
For example:
Link <broadcast-link:1001002>
Window:50 packets
RX packets:7841 fragments:2408/440 bundles:0/0
TX packets:0 fragments:0/0 bundles:0/0
RX naks:0 defs:124 dups:0
TX naks:21 acks:0 retrans:0
Congestion link:0 Send queue max:0 avg:0
In addition, the broadcast-receiver link statistics can be reset in the
usual way via netlink by specifying that link name in command.
Note: the 'tipc_link_name_ext()' is removed because the link name can
now be retrieved simply via the 'l->name'.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some environment, broadcast traffic is suppressed at high rate (i.e.
a kind of bandwidth limit setting). When it is applied, TIPC broadcast
can still run successfully. However, when it comes to a high load, some
packets will be dropped first and TIPC tries to retransmit them but the
packet retransmission is intentionally broadcast too, so making things
worse and not helpful at all.
This commit enables the broadcast retransmission via unicast which only
retransmits packets to the specific peer that has really reported a gap
i.e. not broadcasting to all nodes in the cluster, so will prevent from
being suppressed, and also reduce some overheads on the other peers due
to duplicates, finally improve the overall TIPC broadcast performance.
Note: the functionality can be turned on/off via the sysctl file:
echo 1 > /proc/sys/net/tipc/bc_retruni
echo 0 > /proc/sys/net/tipc/bc_retruni
Default is '0', i.e. the broadcast retransmission still works as usual.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous commit ("tipc: add Gap ACK blocks support for broadcast
link"), we have removed the following link trace events due to the code
changes:
- tipc_link_bc_ack
- tipc_link_retrans
This commit adds them back along with some minor changes to adapt to
the new code.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As achieved through commit 9195948fbf ("tipc: improve TIPC throughput
by Gap ACK blocks"), we apply the same mechanism for the broadcast link
as well. The 'Gap ACK blocks' data field in a 'PROTOCOL/STATE_MSG' will
consist of two parts built for both the broadcast and unicast types:
31 16 15 0
+-------------+-------------+-------------+-------------+
| bgack_cnt | ugack_cnt | len |
+-------------+-------------+-------------+-------------+ -
| gap | ack | |
+-------------+-------------+-------------+-------------+ > bc gacks
: : : |
+-------------+-------------+-------------+-------------+ -
| gap | ack | |
+-------------+-------------+-------------+-------------+ > uc gacks
: : : |
+-------------+-------------+-------------+-------------+ -
which is "automatically" backward-compatible.
We also increase the max number of Gap ACK blocks to 128, allowing upto
64 blocks per type (total buffer size = 516 bytes).
Besides, the 'tipc_link_advance_transmq()' function is refactored which
is applicable for both the unicast and broadcast cases now, so some old
functions can be removed and the code is optimized.
With the patch, TIPC broadcast is more robust regardless of packet loss
or disorder, latency, ... in the underlying network. Its performance is
boost up significantly.
For example, experiment with a 5% packet loss rate results:
$ time tipc-pipe --mc --rdm --data_size 123 --data_num 1500000
real 0m 42.46s
user 0m 1.16s
sys 0m 17.67s
Without the patch:
$ time tipc-pipe --mc --rdm --data_size 123 --data_num 1500000
real 8m 27.94s
user 0m 0.55s
sys 0m 2.38s
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I missed the fact that tcp_v4_err() differs from tcp_v6_err().
After commit 4d1a2d9ec1 ("Rename skb to icmp_skb in tcp_v4_err()")
the skb argument has been renamed to icmp_skb only in one function.
I will in a future patch reconciliate these functions to avoid
this kind of confusion.
Fixes: 45af29ca76 ("tcp: allow traceroute -Mtcp for unpriv users")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 8c46fcd783 ("batman-adv: disable ethtool link speed detection
when auto negotiation off") disabled the usage of ethtool's link_ksetting
when auto negotation was enabled due to invalid values when used with
tun/tap virtual net_devices. According to the patch, automatic measurements
should be used for these kind of interfaces.
But there are major flaws with this argumentation:
* automatic measurements are not implemented
* auto negotiation has nothing to do with the validity of the retrieved
values
The first point has to be fixed by a longer patch series. The "validity"
part of the second point must be addressed in the same patch series by
dropping the usage of ethtool's link_ksetting (thus always doing automatic
measurements over ethernet).
Drop the patch again to have more default values for various net_device
types/configurations. The user can still overwrite them using the
batadv_hardif's BATADV_ATTR_THROUGHPUT_OVERRIDE.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Set VLAN tag in tcp reset/icmp unreachable packets to reject
connections in the bridge family, from Michael Braun.
2) Incorrect subcounter flag update in ipset, from Phil Sutter.
3) Possible buffer overflow in the pptp conntrack helper, based
on patch from Dan Carpenter.
4) Restore userspace conntrack helper hook logic that broke after
hook consolidation rework.
5) Unbreak userspace conntrack helper registration via
nfnetlink_cthelper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix a debugfs vs. wiphy rename crash
* fix an invalid HE spec definition
* fix a mesh timer crash
-----BEGIN PGP SIGNATURE-----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=+uUG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few changes:
* fix a debugfs vs. wiphy rename crash
* fix an invalid HE spec definition
* fix a mesh timer crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was reported by syzbot. When the function br_mrp_parse was
called with a valid net_bridge_port, the net_bridge was an invalid
pointer. Therefore the check br->stp_enabled could pass/fail
depending where it was pointing in memory.
The fix consists of setting the net_bridge pointer if the port is a
valid pointer.
Reported-by: syzbot+9c6f0f1f8e32223df9a4@syzkaller.appspotmail.com
Fixes: 6536993371 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unpriv users can use traceroute over plain UDP sockets, but not TCP ones.
$ traceroute -Mtcp 8.8.8.8
You do not have enough privileges to use this traceroute method.
$ traceroute -n -Mudp 8.8.8.8
traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets
1 192.168.86.1 3.631 ms 3.512 ms 3.405 ms
2 10.1.10.1 4.183 ms 4.125 ms 4.072 ms
3 96.120.88.125 20.621 ms 19.462 ms 20.553 ms
4 96.110.177.65 24.271 ms 25.351 ms 25.250 ms
5 69.139.199.197 44.492 ms 43.075 ms 44.346 ms
6 68.86.143.93 27.969 ms 25.184 ms 25.092 ms
7 96.112.146.18 25.323 ms 96.112.146.22 25.583 ms 96.112.146.26 24.502 ms
8 72.14.239.204 24.405 ms 74.125.37.224 16.326 ms 17.194 ms
9 209.85.251.9 18.154 ms 209.85.247.55 14.449 ms 209.85.251.9 26.296 ms^C
We can easily support traceroute over TCP, by queueing an error message
into socket error queue.
Note that applications need to set IP_RECVERR/IPV6_RECVERR option to
enable this feature, and that the error message is only queued
while in SYN_SNT state.
socket(AF_INET6, SOCK_STREAM, IPPROTO_IP) = 3
setsockopt(3, SOL_IPV6, IPV6_RECVERR, [1], 4) = 0
setsockopt(3, SOL_SOCKET, SO_TIMESTAMP_OLD, [1], 4) = 0
setsockopt(3, SOL_IPV6, IPV6_UNICAST_HOPS, [5], 4) = 0
connect(3, {sa_family=AF_INET6, sin6_port=htons(8787), sin6_flowinfo=htonl(0),
inet_pton(AF_INET6, "2002:a05:6608:297::", &sin6_addr), sin6_scope_id=0}, 28) = -1 EHOSTUNREACH (No route to host)
recvmsg(3, {msg_name={sa_family=AF_INET6, sin6_port=htons(8787), sin6_flowinfo=htonl(0),
inet_pton(AF_INET6, "2002:a05:6608:297::", &sin6_addr), sin6_scope_id=0},
msg_namelen=1024->28, msg_iov=[{iov_base="`\r\337\320\0004\6\1&\7\370\260\200\231\16\27\0\0\0\0\0\0\0\0 \2\n\5f\10\2\227"..., iov_len=1024}],
msg_iovlen=1, msg_control=[{cmsg_len=32, cmsg_level=SOL_SOCKET, cmsg_type=SO_TIMESTAMP_OLD, cmsg_data={tv_sec=1590340680, tv_usec=272424}},
{cmsg_len=60, cmsg_level=SOL_IPV6, cmsg_type=IPV6_RECVERR}],
msg_controllen=96, msg_flags=MSG_ERRQUEUE}, MSG_ERRQUEUE) = 144
Suggested-by: Maciej Żenczykowski <maze@google.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of "n" is capped at 0x1ffffff but it checked for negative
values. I don't think this causes a problem but I'm not certain and
it's harmless to prevent it.
Fixes: 2e04172875 ("ipv4: do compat setsockopt for MCAST_MSFILTER directly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tls_sw_recvmsg() and tls_decrypt_done() can be run concurrently.
// tls_sw_recvmsg()
if (atomic_read(&ctx->decrypt_pending))
crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
else
reinit_completion(&ctx->async_wait.completion);
//tls_decrypt_done()
pending = atomic_dec_return(&ctx->decrypt_pending);
if (!pending && READ_ONCE(ctx->async_notify))
complete(&ctx->async_wait.completion);
Consider the scenario tls_decrypt_done() is about to run complete()
if (!pending && READ_ONCE(ctx->async_notify))
and tls_sw_recvmsg() reads decrypt_pending == 0, does reinit_completion(),
then tls_decrypt_done() runs complete(). This sequence of execution
results in wrong completion. Consequently, for next decrypt request,
it will not wait for completion, eventually on connection close, crypto
resources freed, there is no way to handle pending decrypt response.
This race condition can be avoided by having atomic_read() mutually
exclusive with atomic_dec_return(),complete().Intoduced spin lock to
ensure the mutual exclution.
Addressed similar problem in tx direction.
v1->v2:
- More readable commit message.
- Corrected the lock to fix new race scenario.
- Removed barrier which is not needed now.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The npgs member of struct xdp_umem is an u32 entity, and stores the
number of pages the UMEM consumes. The calculation of npgs
npgs = size / PAGE_SIZE
can overflow.
To avoid overflow scenarios, the division is now first stored in a
u64, and the result is verified to fit into 32b.
An alternative would be storing the npgs as a u64, however, this
wastes memory and is an unrealisticly large packet area.
Fixes: c0c77d8fb7 ("xsk: add user memory registration support sockopt")
Reported-by: "Minh Bùi Quang" <minhquangbui99@gmail.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/CACtPs=GGvV-_Yj6rbpzTVnopgi5nhMoCcTkSkYrJHGQHJWFZMQ@mail.gmail.com/
Link: https://lore.kernel.org/bpf/20200525080400.13195-1-bjorn.topel@gmail.com
Restore helper data size initialization and fix memcopy of the helper
data size.
Fixes: 157ffffeb5 ("netfilter: nfnetlink_cthelper: reject too large userspace allocation requests")
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal says:
"Problem is that after the helper hook was merged back into the confirm
one, the queueing itself occurs from the confirm hook, i.e. we queue
from the last netfilter callback in the hook-list.
Therefore, on return, the packet bypasses the confirm action and the
connection is never committed to the main conntrack table.
To fix this there are several ways:
1. revert the 'Fixes' commit and have a extra helper hook again.
Works, but has the drawback of adding another indirect call for
everyone.
2. Special case this: split the hooks only when userspace helper
gets added, so queueing occurs at a lower priority again,
and normal enqueue reinject would eventually call the last hook.
3. Extend the existing nf_queue ct update hook to allow a forced
confirmation (plus run the seqadj code).
This goes for 3)."
Fixes: 827318feb6 ("netfilter: conntrack: remove helper hook again")
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dan Carpenter says: "Smatch complains that the value for "cmd" comes
from the network and can't be trusted."
Add pptp_msg_name() helper function that checks for the array boundary.
Fixes: f09943fefe ("[NETFILTER]: nf_conntrack/nf_nat: add PPTP helper port")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If IPSET_FLAG_SKIP_SUBCOUNTER_UPDATE is set, user requested to not
update counters in sub sets. Therefore IPSET_FLAG_SKIP_COUNTER_UPDATE
must be set, not unset.
Fixes: 6e01781d1c ("netfilter: ipset: set match: add support to match the counters")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, using the bridge reject target with tagged packets
results in untagged packets being sent back.
Fix this by mirroring the vlan id as well.
Fixes: 85f5b3086a ("netfilter: bridge: add reject support")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It's not intuitively obvious that bpfilter_umh is a statically linked binary.
Mention the toolchain requirement in the Kconfig help, so people
have an easier time figuring out what's needed.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This waring can be triggered simply by:
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 1 mark 0 mask 0x10 #[1]
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 2 mark 0 mask 0x1 #[2]
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 2 mark 0 mask 0x10 #[3]
Then dmesg shows:
[ ] WARNING: CPU: 1 PID: 7265 at net/xfrm/xfrm_policy.c:1548
[ ] RIP: 0010:xfrm_policy_insert_list+0x2f2/0x1030
[ ] Call Trace:
[ ] xfrm_policy_inexact_insert+0x85/0xe50
[ ] xfrm_policy_insert+0x4ba/0x680
[ ] xfrm_add_policy+0x246/0x4d0
[ ] xfrm_user_rcv_msg+0x331/0x5c0
[ ] netlink_rcv_skb+0x121/0x350
[ ] xfrm_netlink_rcv+0x66/0x80
[ ] netlink_unicast+0x439/0x630
[ ] netlink_sendmsg+0x714/0xbf0
[ ] sock_sendmsg+0xe2/0x110
The issue was introduced by Commit 7cb8a93968 ("xfrm: Allow inserting
policies with matching mark and different priorities"). After that, the
policies [1] and [2] would be able to be added with different priorities.
However, policy [3] will actually match both [1] and [2]. Policy [1]
was matched due to the 1st 'return true' in xfrm_policy_mark_match(),
and policy [2] was matched due to the 2nd 'return true' in there. It
caused WARN_ON() in xfrm_policy_insert_list().
This patch is to fix it by only (the same value and priority) as the
same policy in xfrm_policy_mark_match().
Thanks to Yuehaibing, we could make this fix better.
v1->v2:
- check policy->mark.v == pol->mark.v only without mask.
Fixes: 7cb8a93968 ("xfrm: Allow inserting policies with matching mark and different priorities")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Removing the "if (IS_ERR(dir)) dir = NULL;" check only works
if we adjust the remaining code to not rely on it being NULL.
Check IS_ERR_OR_NULL() before attempting to dereference it.
I'm not actually entirely sure this fixes the syzbot crash as
the kernel config indicates that they do have DEBUG_FS in the
kernel, but this is what I found when looking there.
Cc: stable@vger.kernel.org
Fixes: d82574a8e5 ("cfg80211: no need to check return value of debugfs_create functions")
Reported-by: syzbot+fd5332e429401bf42d18@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200525113816.fc4da3ec3d4b.Ica63a110679819eaa9fb3bc1b7437d96b1fd187d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna
Bhowmik.
2) Nexthop attributes aren't being checked properly because of
mis-initialized iterator, from David Ahern.
3) Revert iop_idents_reserve() change as it caused performance
regressions and was just working around what is really a UBSAN bug
in the compiler. From Yuqi Jin.
4) Read MAC address properly from ROM in bmac driver (double iteration
proceeds past end of address array), from Jeremy Kerr.
5) Add Microsoft Surface device IDs to r8152, from Marc Payne.
6) Prevent reference to freed SKB in __netif_receive_skb_core(), from
Boris Sukholitko.
7) Fix ACK discard behavior in rxrpc, from David Howells.
8) Preserve flow hash across packet scrubbing in wireguard, from Jason
A. Donenfeld.
9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric
Dumazet.
10) Fix encryption error checking in kTLS code, from Vadim Fedorenko.
11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki.
12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet.
13) Fix use after free in mlxsw driver, from Jiri Pirko.
14) Order kTLS key destruction properly in mlx5 driver, from Tariq
Toukan.
15) Check devm_platform_ioremap_resource() return value properly in
several drivers, from Tiezhu Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
net: smsc911x: Fix runtime PM imbalance on error
net/mlx4_core: fix a memory leak bug.
net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
net: phy: mscc: fix initialization of the MACsec protocol mode
net: stmmac: don't attach interface until resume finishes
net: Fix return value about devm_platform_ioremap_resource()
net/mlx5: Fix error flow in case of function_setup failure
net/mlx5e: CT: Correctly get flow rule
net/mlx5e: Update netdev txq on completions during closure
net/mlx5: Annotate mutex destroy for root ns
net/mlx5: Don't maintain a case of del_sw_func being null
net/mlx5: Fix cleaning unmanaged flow tables
net/mlx5: Fix memory leak in mlx5_events_init
net/mlx5e: Fix inner tirs handling
net/mlx5e: kTLS, Destroy key object after destroying the TIS
net/mlx5e: Fix allowed tc redirect merged eswitch offload cases
net/mlx5: Avoid processing commands before cmdif is ready
net/mlx5: Fix a race when moving command interface to events mode
net/mlx5: Add command entry handling completion
rxrpc: Fix a memory leak in rxkad_verify_response()
...
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide devm_register_netdev() - a device resource managed variant
of register_netdev(). This new helper will only work for net_device
structs that are also already managed by devres.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not using a proxy structure to store struct net_device doesn't save
anything in terms of compiled code size or memory usage but significantly
decreases the readability of the code with all the pointer casting.
Define struct net_device_devres and use it in devm_alloc_etherdev_mqs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently only a single devres helper in net/ - devm variant
of alloc_etherdev. Let's move it to net/devres.c with the intention of
assing a second one: devm_register_netdev(). This new routine will need
to know the address of the release function of devm_alloc_etherdev() so
that it can verify (using devres_find()) that the struct net_device
that's being passed to it is also resource managed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix psample build error when CONFIG_INET is not set/enabled by
bracketing the tunnel code in #ifdef CONFIG_NET / #endif.
../net/psample/psample.c: In function ‘__psample_ip_tun_to_nlattr’:
../net/psample/psample.c:216:25: error: implicit declaration of function ‘ip_tunnel_info_opts’; did you mean ‘ip_tunnel_info_opts_set’? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A ticket was not released after a call of the function
"rxkad_decrypt_ticket" failed. Thus replace the jump target
"temporary_error_free_resp" by "temporary_error_free_ticket".
Fixes: 8c2f826dc3 ("rxrpc: Don't put crypto buffers on the stack")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Markus Elfring <Markus.Elfring@web.de>
When a MRP instance is deleted, then restore the port according to the
bridge state. If the bridge is up then the ports will be in forwarding
state otherwise will be in disabled state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allow to have the same net bridge port part of multiple MRP
rings. Therefore add a check if the port is used already in a different
MRP. In that case return failure.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=jJvy
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20200520' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix retransmission timeout and ACK discard
Here are a couple of fixes and an extra tracepoint for AF_RXRPC:
(1) Calculate the RTO pretty much as TCP does, rather than making
something up, including an initial 4s timeout (which causes return
probes from the fileserver to fail if a packet goes missing), and add
backoff.
(2) Fix the discarding of out-of-order received ACKs. We mustn't let the
hard-ACK point regress, nor do we want to do unnecessary
retransmission because the soft-ACK list regresses. This is not
trivial, however, due to some loose wording in various old protocol
specs, the ACK field that should be used for this sometimes has the
wrong information in it.
(3) Add a tracepoint to log a discarded ACK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make FLOW_ACTION_HW_STATS_DONT_CARE be all bits, rather than none, so that
drivers and __flow_action_hw_stats_check can use simple bitwise checks.
Pre-fill all actions with DONT_CARE in flow_rule_alloc(), rather than
relying on implicit semantics of zero from kzalloc, so that callers which
don't configure action stats themselves (i.e. netfilter) get the correct
behaviour by default.
Only the kernel's internal API semantics change; the TC uAPI is unaffected.
v4: move DONT_CARE setting to flow_rule_alloc() for robustness and simplicity.
v3: set DONT_CARE in nft and ct offload.
v2: rebased on net-next, removed RFC tags.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 tunnel devices in AF_MPLS.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is just preparation for MPLS support in ip6_tunnel
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge ip{4,6}ip6_tnl_xmit functions into one universal
ipxip6_tnl_xmit in preparation for adding MPLS support.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bdf6fa52f0 ("sctp: handle association restarts when the
socket is closed.") starts shutdown when an association is restarted,
if in SHUTDOWN-PENDING state and the socket is closed. However, the
rationale stated in that commit applies also when in SHUTDOWN-SENT
state - we don't want to move an association to ESTABLISHED state when
the socket has been closed, because that results in an association
that is unreachable from user space.
The problem scenario:
1. Client crashes and/or restarts.
2. Server (using one-to-one socket) calls close(). SHUTDOWN is lost.
3. Client reconnects using the same addresses and ports.
4. Server's association is restarted. The association and the socket
move to ESTABLISHED state, even though the server process has
closed its descriptor.
Also, after step 4 when the server process exits, some resources are
leaked in an attempt to release the underlying inet sock structure in
ESTABLISHED state:
IPv4: Attempt to release TCP socket in state 1 00000000377288c7
Fix by acting the same way as in SHUTDOWN-PENDING state. That is, if
an association is restarted in SHUTDOWN-SENT state and the socket is
closed, then start shutdown and don't move the association or the
socket to ESTABLISHED state.
Fixes: bdf6fa52f0 ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-05-22
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 3 day(s) which contain
a total of 5 files changed, 69 insertions(+), 11 deletions(-).
The main changes are:
1) Fix to reject mmap()'ing read-only array maps as writable since BPF verifier
relies on such map content to be frozen, from Andrii Nakryiko.
2) Fix breaking audit from secid_to_secctx() LSM hook by avoiding to use
call_int_hook() since this hook is not stackable, from KP Singh.
3) Fix BPF flow dissector program ref leak on netns cleanup, from Jakub Sitnicki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is some ambiguity in the RFC as to whether the ADD_ADDR HMAC is
the rightmost 64 bits of the entire hash or of the leftmost 160 bits
of the hash. The intention, as clarified with the author of the RFC,
is the entire hash.
This change returns the entire hash from
mptcp_crypto_hmac_sha (instead of only the first 160 bits), and moves
any truncation/selection operation on the hash to the caller.
Fixes: 12555a2d97 ("mptcp: use rightmost 64 bits in ADD_ADDR HMAC")
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Todd Malsbary <todd.malsbary@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds nexthop add/del notifiers. To be used by
vxlan driver in a later patch. Could possibly be used by
switchdev drivers in the future.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Todays vxlan mac fdb entries can point to multiple remote
ips (rdsts) with the sole purpose of replicating
broadcast-multicast and unknown unicast packets to those remote ips.
E-VPN multihoming [1,2,3] requires bridged vxlan traffic to be
load balanced to remote switches (vteps) belonging to the
same multi-homed ethernet segment (E-VPN multihoming is analogous
to multi-homed LAG implementations, but with the inter-switch
peerlink replaced with a vxlan tunnel). In other words it needs
support for mac ecmp. Furthermore, for faster convergence, E-VPN
multihoming needs the ability to update fdb ecmp nexthops independent
of the fdb entries.
New route nexthop API is perfect for this usecase.
This patch extends the vxlan fdb code to take a nexthop id
pointing to an ecmp nexthop group.
Changes include:
- New NDA_NH_ID attribute for fdbs
- Use the newly added fdb nexthop groups
- makes vxlan rdsts and nexthop handling code mutually
exclusive
- since this is a new use-case and the requirement is for ecmp
nexthop groups, the fdb add and update path checks that the
nexthop is really an ecmp nexthop group. This check can be relaxed
in the future, if we want to introduce replication fdb nexthop groups
and allow its use in lieu of current rdst lists.
- fdb update requests with nexthop id's only allowed for existing
fdb's that have nexthop id's
- learning will not override an existing fdb entry with nexthop
group
- I have wrapped the switchdev offload code around the presence of
rdst
[1] E-VPN RFC https://tools.ietf.org/html/rfc7432
[2] E-VPN with vxlan https://tools.ietf.org/html/rfc8365
[3] http://vger.kernel.org/lpc_net2018_talks/scaling_bridge_fdb_database_slidesV3.pdf
Includes a null check fix in vxlan_xmit from Nikolay
v2 - Fixed build issue:
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ecmp nexthops and nexthop groups
for mac fdb entries. In subsequent patches this is used
by the vxlan driver fdb entries. The use case is
E-VPN multihoming [1,2,3] which requires bridged vxlan traffic
to be load balanced to remote switches (vteps) belonging to
the same multi-homed ethernet segment (This is analogous to
a multi-homed LAG but over vxlan).
Changes include new nexthop flag NHA_FDB for nexthops
referenced by fdb entries. These nexthops only have ip.
This patch includes appropriate checks to avoid routes
referencing such nexthops.
example:
$ip nexthop add id 12 via 172.16.1.2 fdb
$ip nexthop add id 13 via 172.16.1.3 fdb
$ip nexthop add id 102 group 12/13 fdb
$bridge fdb add 02:02:00:00:00:13 dev vxlan1000 nhid 101 self
[1] E-VPN https://tools.ietf.org/html/rfc7432
[2] E-VPN VxLAN: https://tools.ietf.org/html/rfc8365
[3] LPC talk with mention of nexthop groups for L2 ecmp
http://vger.kernel.org/lpc_net2018_talks/scaling_bridge_fdb_database_slidesV3.pdf
v4 - fixed uninitialized variable reported by kernel test robot
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a63fc6b75c ("rcu: Upgrade rcu_swap_protected() to
rcu_replace_pointer()") a new helper macro named rcu_replace_pointer() was
introduced to simplify code requiring to switch an rcu pointer to a new
value while extracting the old one.
Use rcu_replace_pointer() where appropriate to make code slimer.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes") reverts the commit ab92d68fc2 ("net: core: add generic lockdep
keys"). But it forgot to also revert the commit 5759af0682 ("batman-adv:
Drop lockdep.h include for soft-interface.c") which depends on the latter.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When attaching a flow dissector program to a network namespace with
bpf(BPF_PROG_ATTACH, ...) we grab a reference to bpf_prog.
If netns gets destroyed while a flow dissector is still attached, and there
are no other references to the prog, we leak the reference and the program
remains loaded.
Leak can be reproduced by running flow dissector tests from selftests/bpf:
# bpftool prog list
# ./test_flow_dissector.sh
...
selftests: test_flow_dissector [PASS]
# bpftool prog list
4: flow_dissector name _dissect tag e314084d332a5338 gpl
loaded_at 2020-05-20T18:50:53+0200 uid 0
xlated 552B jited 355B memlock 4096B map_ids 3,4
btf_id 4
#
Fix it by detaching the flow dissector program when netns is going away.
Fixes: d58e468b11 ("flow_dissector: implements flow dissector BPF hook")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200521083435.560256-1-jakub@cloudflare.com
In order to reduce the number of function calls, the struct
xsk_buff_pool definition is moved to xsk_buff_pool.h. The functions
xp_get_dma(), xp_dma_sync_for_cpu(), xp_dma_sync_for_device(),
xp_validate_desc() and various helper functions are explicitly
inlined.
Further, move xp_get_handle() and xp_release() to xsk.c, to allow for
the compiler to perform inlining.
rfc->v1: Make sure xp_validate_desc() is inlined for Tx perf. (Maxim)
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-15-bjorn.topel@gmail.com
The xdp_return_{frame,frame_rx_napi,buff} function are never used,
except in xdp_convert_zc_to_xdp_frame(), by the MEM_TYPE_XSK_BUFF_POOL
memory type.
To simplify and reduce code, change so that
xdp_convert_zc_to_xdp_frame() calls xsk_buff_free() directly since the
type is know, and remove MEM_TYPE_XSK_BUFF_POOL from the switch
statement in __xdp_return() function.
Suggested-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-14-bjorn.topel@gmail.com
There are no users of MEM_TYPE_ZERO_COPY. Remove all corresponding
code, including the "handle" member of struct xdp_buff.
rfc->v1: Fixed spelling in commit message. (Björn)
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-13-bjorn.topel@gmail.com
In order to simplify AF_XDP zero-copy enablement for NIC driver
developers, a new AF_XDP buffer allocation API is added. The
implementation is based on a single core (single producer/consumer)
buffer pool for the AF_XDP UMEM.
A buffer is allocated using the xsk_buff_alloc() function, and
returned using xsk_buff_free(). If a buffer is disassociated with the
pool, e.g. when a buffer is passed to an AF_XDP socket, a buffer is
said to be released. Currently, the release function is only used by
the AF_XDP internals and not visible to the driver.
Drivers using this API should register the XDP memory model with the
new MEM_TYPE_XSK_BUFF_POOL type.
The API is defined in net/xdp_sock_drv.h.
The buffer type is struct xdp_buff, and follows the lifetime of
regular xdp_buffs, i.e. the lifetime of an xdp_buff is restricted to
a NAPI context. In other words, the API is not replacing xdp_frames.
In addition to introducing the API and implementations, the AF_XDP
core is migrated to use the new APIs.
rfc->v1: Fixed build errors/warnings for m68k and riscv. (kbuild test
robot)
Added headroom/chunk size getter. (Maxim/Björn)
v1->v2: Swapped SoBs. (Maxim)
v2->v3: Initialize struct xdp_buff member frame_sz. (Björn)
Add API to query the DMA address of a frame. (Maxim)
Do DMA sync for CPU till the end of the frame to handle
possible growth (frame_sz). (Maxim)
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-6-bjorn.topel@gmail.com
Move the XSK_NEXT_PG_CONTIG_{MASK,SHIFT}, and
XDP_UMEM_USES_NEED_WAKEUP defines from xdp_sock.h to the AF_XDP
internal xsk.h file. Also, start using the BIT{,_ULL} macro instead of
explicit shifts.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-5-bjorn.topel@gmail.com
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
The XSKMAP is partly implemented by net/xdp/xsk.c. Move xskmap.c from
kernel/bpf/ to net/xdp/, which is the logical place for AF_XDP related
code. Also, move AF_XDP struct definitions, and function declarations
only used by AF_XDP internals into net/xdp/xsk.h.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-3-bjorn.topel@gmail.com
In case we can't find a ->dumpit callback for the requested
(family,type) pair, we fall back to (PF_UNSPEC,type). In effect, we're
in the same situation as if userspace had requested a PF_UNSPEC
dump. For RTM_GETROUTE, that handler is rtnl_dump_all, which calls all
the registered RTM_GETROUTE handlers.
The requested table id may or may not exist for all of those
families. commit ae677bbb44 ("net: Don't return invalid table id
error when dumping all families") fixed the problem when userspace
explicitly requests a PF_UNSPEC dump, but missed the fallback case.
For example, when we pass ipv6.disable=1 to a kernel with
CONFIG_IP_MROUTE=y and CONFIG_IP_MROUTE_MULTIPLE_TABLES=y,
the (PF_INET6, RTM_GETROUTE) handler isn't registered, so we end up in
rtnl_dump_all, and listing IPv6 routes will unexpectedly print:
# ip -6 r
Error: ipv4: MR table does not exist.
Dump terminated
commit ae677bbb44 introduced the dump_all_families variable, which
gets set when userspace requests a PF_UNSPEC dump. However, we can't
simply set the family to PF_UNSPEC in rtnetlink_rcv_msg in the
fallback case to get dump_all_families == true, because some messages
types (for example RTM_GETRULE and RTM_GETNEIGH) only register the
PF_UNSPEC handler and use the family to filter in the kernel what is
dumped to userspace. We would then export more entries, that userspace
would have to filter. iproute does that, but other programs may not.
Instead, this patch removes dump_all_families and updates the
RTM_GETROUTE handlers to check if the family that is being dumped is
their own. When it's not, which covers both the intentional PF_UNSPEC
dumps (as dump_all_families did) and the fallback case, ignore the
missing table id error.
Fixes: cb167893f4 ("net: Plumb support for filtering ipv4 and ipv6 multicast route dumps")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error with MPLS support the code is misusing AF_INET
instead of AF_MPLS.
Fixes: 1b69e7e6c4 ("ipip: support MPLS over IPv4")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot free record on any transient error because it leads to
losing previos data. Check socket error to know whether record must
be freed or not.
Fixes: d10523d0b3 ("net/tls: free the record on encryption error")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_exec_tx_verdict() can return negative value for copied
variable. In that case this value will be pushed back to caller
and the real error code will be lost. Fix it using signed type and
checking for positive value.
Fixes: d10523d0b3 ("net/tls: free the record on encryption error")
Fixes: d3b18ad31f ("tls: add bpf support to sk_msg handling")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the traversal of the list is completed with list_for_each_entry(),
the iterator (node) will point to an invalid object. So passing this to
qrtr_local_enqueue() which is outside of the iterator block is erroneous
eventhough the object is not used.
So fix this by passing NULL to qrtr_local_enqueue().
Fixes: bdabad3e36 ("net: Add Qualcomm IPC router")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, psample can only send the packet bits after decapsulation.
The tunnel information is lost. Add the tunnel support.
If the sampled packet has no tunnel info, the behavior is the same as
before. If it has, add a nested metadata field named PSAMPLE_ATTR_TUNNEL
and include the tunnel subfields if applicable.
Increase the metadata length for sampled packet with the tunnel info.
If new subfields of tunnel info should be included, update the metadata
length accordingly.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl7BzV8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGg8EH/A2pXMTxtc96RI4S
sttEsUQqbakFS0Z/2tQPpMGr/qW2e5eHgsTX/a3SiUeZiIXk6f4lMFkMuctzBf7p
X77cNEDwGOEdbtCXTsMcmKSde7sP2zCXsPB8xTWLyE6rnaFRgikwwkeqgkIKhp1h
bvOQV0t9HNGvxGAM0iZeOvQAvFl4vd7nS123/MYbir9cugfQUSJRueQ4BiCiJqVE
6cNA7/vFzDJuFGszzIrJ7HXn/IdQMMWHkvTDjgBw0GZw1mDbGFbfbZwOeTz1ojCt
smUQ4tIFxBa/VA5zx7dOy2P2keHbSVf4VLkZRPcceT7OqVS65ETmFDp+qt5NdWM5
vZ8+7/0=
=CyYH
-----END PGP SIGNATURE-----
Merge tag 'v5.7-rc6' into rdma.git for-next
Linux 5.7-rc6
Conflict in drivers/net/ethernet/mellanox/mlx5/core/steering/dr_send.c
resolved by deleting dr_cq_event, matching how netdev resolved it.
Required for dependencies in the following patches.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Highlights of this series:
* Remove serialization of sending RPC/RDMA Replies
* Convert the TCP socket send path to use xdr_buf::bvecs (pre-requisite for
RPC-on-TLS)
* Fix svcrdma backchannel sendto return code
* Convert a number of dprintk call sites to use tracepoints
* Fix the "suggest braces around empty body in an 'else' statement" warning
Fixes data remnant seen when we fail to reserve space for a
nexthop group during a larger dump.
If we fail the reservation, we goto nla_put_failure and
cancel the message.
Reproduce with the following iproute2 commands:
=====================
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip link add dummy20 type dummy
ip link add dummy21 type dummy
ip link add dummy22 type dummy
ip link add dummy23 type dummy
ip link add dummy24 type dummy
ip link add dummy25 type dummy
ip link add dummy26 type dummy
ip link add dummy27 type dummy
ip link add dummy28 type dummy
ip link add dummy29 type dummy
ip link add dummy30 type dummy
ip link add dummy31 type dummy
ip link add dummy32 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip link set dummy3 up
ip link set dummy4 up
ip link set dummy5 up
ip link set dummy6 up
ip link set dummy7 up
ip link set dummy8 up
ip link set dummy9 up
ip link set dummy10 up
ip link set dummy11 up
ip link set dummy12 up
ip link set dummy13 up
ip link set dummy14 up
ip link set dummy15 up
ip link set dummy16 up
ip link set dummy17 up
ip link set dummy18 up
ip link set dummy19 up
ip link set dummy20 up
ip link set dummy21 up
ip link set dummy22 up
ip link set dummy23 up
ip link set dummy24 up
ip link set dummy25 up
ip link set dummy26 up
ip link set dummy27 up
ip link set dummy28 up
ip link set dummy29 up
ip link set dummy30 up
ip link set dummy31 up
ip link set dummy32 up
ip link set dummy33 up
ip link set dummy34 up
ip link set vrf-red up
ip link set vrf-blue up
ip link set dummyVRFred up
ip link set dummyVRFblue up
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip ro add 1.1.1.20/32 dev dummy20
ip ro add 1.1.1.21/32 dev dummy21
ip ro add 1.1.1.22/32 dev dummy22
ip ro add 1.1.1.23/32 dev dummy23
ip ro add 1.1.1.24/32 dev dummy24
ip ro add 1.1.1.25/32 dev dummy25
ip ro add 1.1.1.26/32 dev dummy26
ip ro add 1.1.1.27/32 dev dummy27
ip ro add 1.1.1.28/32 dev dummy28
ip ro add 1.1.1.29/32 dev dummy29
ip ro add 1.1.1.30/32 dev dummy30
ip ro add 1.1.1.31/32 dev dummy31
ip ro add 1.1.1.32/32 dev dummy32
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 20 via 1.1.1.20 dev dummy20
ip next add id 21 via 1.1.1.21 dev dummy21
ip next add id 22 via 1.1.1.22 dev dummy22
ip next add id 23 via 1.1.1.23 dev dummy23
ip next add id 24 via 1.1.1.24 dev dummy24
ip next add id 25 via 1.1.1.25 dev dummy25
ip next add id 26 via 1.1.1.26 dev dummy26
ip next add id 27 via 1.1.1.27 dev dummy27
ip next add id 28 via 1.1.1.28 dev dummy28
ip next add id 29 via 1.1.1.29 dev dummy29
ip next add id 30 via 1.1.1.30 dev dummy30
ip next add id 31 via 1.1.1.31 dev dummy31
ip next add id 32 via 1.1.1.32 dev dummy32
i=100
while [ $i -le 200 ]
do
ip next add id $i group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
echo $i
((i++))
done
ip next add id 999 group 1/2/3/4/5/6
ip next ls
========================
Fixes: ab84be7e54 ("net: Initial nexthop code")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atm_dev_ioctl() does copyin in two different ways - one for
ATM_GETNAMES, another for everything else. Start with separating
the former into a new helper (atm_getnames()). The next step
will be to lift the copyin into the callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Native ->setsockopt() handling of these options (MCAST_..._SOURCE_GROUP
and MCAST_{,UN}BLOCK_SOURCE) consists of copyin + call of a helper that
does the actual work. The only change needed for ->compat_setsockopt()
is a slightly different copyin - the helpers can be reused as-is.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
direct parallel to the way these two are handled in the native
->setsockopt() instances - the helpers that do the real work
are already separated and can be reused as-is in this case.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Parallel to what the native setsockopt() does, except that unlike
the native setsockopt() we do not use memdup_user() - we want
the sockaddr_storage fields properly aligned, so we allocate
4 bytes more and copy compat_group_filter at the offset 4,
which yields the proper alignments.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
now we can do MCAST_MSFILTER in compat ->getsockopt() without
playing silly buggers with copying things back and forth.
We can form a native struct group_filter (sans the variable-length
tail) on stack, pass that + pointer to the tail of original request
to the helper doing the bulk of the work, then do the rest of
copyout - same as the native getsockopt() does.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
pass the userland pointer to the array in its tail, so that part
gets copied out by our functions; copyout of everything else is
done in the callers. Rationale: reuse for compat; the array
is the same in native and compat, the layout of parts before it
is different for compat.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We want to get rid of compat_mc_[sg]etsockopt() and to have that stuff
handled without compat_alloc_user_space(), extra copying through
userland, etc. To do that we'll need ipv4 and ipv6 instances of
->compat_[sg]etsockopt() to manipulate the 32bit variants of mcast
requests, so we need to move the definitions of those out of net/compat.c
and into a public header.
This patch just does a mechanical move to include/net/compat.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Rename these so they are easy to enable and search for as a set
- Move the tracepoints to get a more accurate sense of control flow
- Tracepoints should not fire on xprt shutdown
- Display memory address in case data structure had been corrupted
- Abandon dprintk in these paths
I haven't ever gotten one of these tracepoints to trigger. I wonder
if we should simply remove them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up. At this point, we are not ready yet to support bio_vecs in
the UDP transport implementation. However, we can clean up
svc_udp_recvfrom() to match the tracing and straight-lining recently
changes made in svc_tcp_recvfrom().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
This function is not currently "generic" so remove the documenting
comment and rename it appropriately. Its internals are converted to
use bio_vecs for reading from the transport socket.
In existing typical sunrpc uses of bio_vecs, the bio_vec array is
allocated dynamically. Here, instead, an array of bio_vecs is added
to svc_rqst. The lifetime of this array can be greater than one call
to xpo_recvfrom():
- Multiple calls to xpo_recvfrom() might be needed to read an RPC
message completely.
- At some later point, rq_arg.bvecs will point to this array and it
will carry the received message into svc_process().
I also expect that a future optimization will remove either the
rq_vec or rq_pages array in favor of rq_bvec, thus conserving the
size of struct svc_rqst.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The conversion to pin_user_pages() had a bug: it overlooked
the case of allocation of pages failing. Fix that by restoring
an equivalent check.
Reported-by: syzbot+118ac0af4ac7f785a45b@syzkaller.appspotmail.com
Fixes: dbfe7d7437 ("rds: convert get_user_pages() --> pin_user_pages()")
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: rds-devel@oss.oracle.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EIR flags should just hint if SSP may be supported but we shall verify
this with use of the actual features as the SSP bits may be disabled in
the lower layers which would result in legacy authentication to be
used.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Rx protocol has a "previousPacket" field in it that is not handled in
the same way by all protocol implementations. Sometimes it contains the
serial number of the last DATA packet received, sometimes the sequence
number of the last DATA packet received and sometimes the highest sequence
number so far received.
AF_RXRPC is using this to weed out ACKs that are out of date (it's possible
for ACK packets to get reordered on the wire), but this does not work with
OpenAFS which will just stick the sequence number of the last packet seen
into previousPacket.
The issue being seen is that big AFS FS.StoreData RPC (eg. of ~256MiB) are
timing out when partly sent. A trace was captured, with an additional
tracepoint to show ACKs being discarded in rxrpc_input_ack(). Here's an
excerpt showing the problem.
52873.203230: rxrpc_tx_data: c=000004ae DATA ed1a3584:00000002 0002449c q=00024499 fl=09
A DATA packet with sequence number 00024499 has been transmitted (the "q="
field).
...
52873.243296: rxrpc_rx_ack: c=000004ae 00012a2b DLY r=00024499 f=00024497 p=00024496 n=0
52873.243376: rxrpc_rx_ack: c=000004ae 00012a2c IDL r=0002449b f=00024499 p=00024498 n=0
52873.243383: rxrpc_rx_ack: c=000004ae 00012a2d OOS r=0002449d f=00024499 p=0002449a n=2
The Out-Of-Sequence ACK indicates that the server didn't see DATA sequence
number 00024499, but did see seq 0002449a (previousPacket, shown as "p=",
skipped the number, but firstPacket, "f=", which shows the bottom of the
window is set at that point).
52873.252663: rxrpc_retransmit: c=000004ae q=24499 a=02 xp=14581537
52873.252664: rxrpc_tx_data: c=000004ae DATA ed1a3584:00000002 000244bc q=00024499 fl=0b *RETRANS*
The packet has been retransmitted. Retransmission recurs until the peer
says it got the packet.
52873.271013: rxrpc_rx_ack: c=000004ae 00012a31 OOS r=000244a1 f=00024499 p=0002449e n=6
More OOS ACKs indicate that the other packets that are already in the
transmission pipeline are being received. The specific-ACK list is up to 6
ACKs and NAKs.
...
52873.284792: rxrpc_rx_ack: c=000004ae 00012a49 OOS r=000244b9 f=00024499 p=000244b6 n=30
52873.284802: rxrpc_retransmit: c=000004ae q=24499 a=0a xp=63505500
52873.284804: rxrpc_tx_data: c=000004ae DATA ed1a3584:00000002 000244c2 q=00024499 fl=0b *RETRANS*
52873.287468: rxrpc_rx_ack: c=000004ae 00012a4a OOS r=000244ba f=00024499 p=000244b7 n=31
52873.287478: rxrpc_rx_ack: c=000004ae 00012a4b OOS r=000244bb f=00024499 p=000244b8 n=32
At this point, the server's receive window is full (n=32) with presumably 1
NAK'd packet and 31 ACK'd packets. We can't transmit any more packets.
52873.287488: rxrpc_retransmit: c=000004ae q=24499 a=0a xp=61327980
52873.287489: rxrpc_tx_data: c=000004ae DATA ed1a3584:00000002 000244c3 q=00024499 fl=0b *RETRANS*
52873.293850: rxrpc_rx_ack: c=000004ae 00012a4c DLY r=000244bc f=000244a0 p=00024499 n=25
And now we've received an ACK indicating that a DATA retransmission was
received. 7 packets have been processed (the occupied part of the window
moved, as indicated by f= and n=).
52873.293853: rxrpc_rx_discard_ack: c=000004ae r=00012a4c 000244a0<00024499 00024499<000244b8
However, the DLY ACK gets discarded because its previousPacket has gone
backwards (from p=000244b8, in the ACK at 52873.287478 to p=00024499 in the
ACK at 52873.293850).
We then end up in a continuous cycle of retransmit/discard. kafs fails to
update its window because it's discarding the ACKs and can't transmit an
extra packet that would clear the issue because the window is full.
OpenAFS doesn't change the previousPacket value in the ACKs because no new
DATA packets are received with a different previousPacket number.
Fix this by altering the discard check to only discard an ACK based on
previousPacket if there was no advance in the firstPacket. This allows us
to transmit a new packet which will cause previousPacket to advance in the
next ACK.
The check, however, needs to allow for the possibility that previousPacket
may actually have had the serial number placed in it instead - in which
case it will go outside the window and we should ignore it.
Fixes: 1a2391c30c ("rxrpc: Fix detection of out of order acks")
Reported-by: Dave Botsch <botsch@cnf.cornell.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
skb_gro_receive() used to be used by SCTP, it is no longer the case.
skb_gro_receive_list() is in the same category : never used from modules.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BUG halt was reported a while back, but the patch somehow got
missed:
PID: 2879 TASK: c16adaa0 CPU: 1 COMMAND: "sctpn"
#0 [f418dd28] crash_kexec at c04a7d8c
#1 [f418dd7c] oops_end at c0863e02
#2 [f418dd90] do_invalid_op at c040aaca
#3 [f418de28] error_code (via invalid_op) at c08631a5
EAX: f34baac0 EBX: 00000090 ECX: f418deb0 EDX: f5542950 EBP: 00000000
DS: 007b ESI: f34ba800 ES: 007b EDI: f418dea0 GS: 00e0
CS: 0060 EIP: c046fa5e ERR: ffffffff EFLAGS: 00010286
#4 [f418de5c] add_timer at c046fa5e
#5 [f418de68] sctp_do_sm at f8db8c77 [sctp]
#6 [f418df30] sctp_primitive_SHUTDOWN at f8dcc1b5 [sctp]
#7 [f418df48] inet_shutdown at c080baf9
#8 [f418df5c] sys_shutdown at c079eedf
#9 [f418df70] sys_socketcall at c079fe88
EAX: ffffffda EBX: 0000000d ECX: bfceea90 EDX: 0937af98
DS: 007b ESI: 0000000c ES: 007b EDI: b7150ae4
SS: 007b ESP: bfceea7c EBP: bfceeaa8 GS: 0033
CS: 0073 EIP: b775c424 ERR: 00000066 EFLAGS: 00000282
It appears that the side effect that starts the shutdown timer was processed
multiple times, which can happen as multiple paths can trigger it. This of
course leads to the BUG halt in add_timer getting called.
Fix seems pretty straightforward, just check before the timer is added if its
already been started. If it has mod the timer instead to min(current
expiration, new expiration)
Its been tested but not confirmed to fix the problem, as the issue has only
occured in production environments where test kernels are enjoined from being
installed. It appears to be a sane fix to me though. Also, recentely,
Jere found a reproducer posted on list to confirm that this resolves the
issues
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jere.leppanen@nokia.com
CC: marcelo.leitner@gmail.com
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ->ndo_tunnel_ctl instead of overriding the address limit
and using ->ndo_do_ioctl just to do a pointless user copy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out a addrconf_set_sit_dstaddr helper for the actual work if we
found a SIT device, and only hold the rtnl lock around the device lookup
and that new helper, as there is no point in holding it over a
copy_from_user call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in copying the structure from userspace or looking up
a device if SIT support is not disabled and we'll eventually return
-ENODEV anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ->ndo_tunnel_ctl method, and use ip_tunnel_ioctl to
handle userspace requests for the SIOCGETTUNNEL, SIOCADDTUNNEL,
SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the ioctl handler into one function per command instead of having
a all the logic sit in one giant switch statement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ->ndo_tunnel_ctl instead of overriding the address limit
and using ->ndo_do_ioctl just to do a pointless user copy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This method is used to properly allow kernel callers of the IPv4 route
management ioctls. The exsting ip_tunnel_ioctl helper is renamed to
ip_tunnel_ctl to better reflect that it doesn't directly implement ioctls
touching user memory, and is used for the guts of ndo_tunnel_ctl
implementations. A new ip_tunnel_ioctl helper is added that can be wired
up directly to the ndo_do_ioctl method and takes care of the copy to and
from userspace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the dev_set_allmulti call and the error handling into the
ioctl helper. This allows reusing already looked up tunnel_dev pointer
and the set up argument structure for the deletion in the error handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce a few level of indentation to simplify the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
__netif_receive_skb_core may change the skb pointer passed into it (e.g.
in rx_handler). The original skb may be freed as a result of this
operation.
The callers of __netif_receive_skb_core may further process original skb
by using pt_prev pointer returned by __netif_receive_skb_core thus
leading to unpleasant effects.
The solution is to pass skb by reference into __netif_receive_skb_core.
v2: Added Fixes tag and comment regarding ppt_prev and skb invariant.
Fixes: 88eb1944e1 ("net: core: propagate SKB lists through packet_type lookup")
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 637bc8bbe6 ("inet: reset tb->fastreuseport when adding a reuseport sk")
added a bind-address cache in tb->fast*. The tb->fast* caches the address
of a sk which has successfully been binded with SO_REUSEPORT ON. The idea
is to avoid the expensive conflict search in inet_csk_bind_conflict().
There is an issue with wildcard matching where sk_reuseport_match() should
have returned false but it is currently returning true. It ends up
hiding bind conflict. For example,
bind("[::1]:443"); /* without SO_REUSEPORT. Succeed. */
bind("[::2]:443"); /* with SO_REUSEPORT. Succeed. */
bind("[::]:443"); /* with SO_REUSEPORT. Still Succeed where it shouldn't */
The last bind("[::]:443") with SO_REUSEPORT on should have failed because
it should have a conflict with the very first bind("[::1]:443") which
has SO_REUSEPORT off. However, the address "[::2]" is cached in
tb->fast* in the second bind. In the last bind, the sk_reuseport_match()
returns true because the binding sk's wildcard addr "[::]" matches with
the "[::2]" cached in tb->fast*.
The correct bind conflict is reported by removing the second
bind such that tb->fast* cache is not involved and forces the
bind("[::]:443") to go through the inet_csk_bind_conflict():
bind("[::1]:443"); /* without SO_REUSEPORT. Succeed. */
bind("[::]:443"); /* with SO_REUSEPORT. -EADDRINUSE */
The expected behavior for sk_reuseport_match() is, it should only allow
the "cached" tb->fast* address to be used as a wildcard match but not
the address of the binding sk. To do that, the current
"bool match_wildcard" arg is split into
"bool match_sk1_wildcard" and "bool match_sk2_wildcard".
This change only affects the sk_reuseport_match() which is only
used by inet_csk (e.g. TCP).
The other use cases are calling inet_rcv_saddr_equal() and
this patch makes it pass the same "match_wildcard" arg twice to
the "ipv[46]_rcv_saddr_equal(..., match_wildcard, match_wildcard)".
Cc: Josef Bacik <jbacik@fb.com>
Fixes: 637bc8bbe6 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bunch of forward declarations (trivially shifting code around
where needed), and make a few functions static.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txmsg is declared as {0}, no need to clear individual fields later on.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 394216275c ("s390: remove broken hibernate / power management support")
removed support for ARCH_HIBERNATION_POSSIBLE from s390.
So drop the unused pm ops from the s390-only af_iucv socket code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 394216275c ("s390: remove broken hibernate / power management support")
removed support for ARCH_HIBERNATION_POSSIBLE from s390.
So drop the unused pm ops from the s390-only iucv bus driver.
CC: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the HMAC used in the ADD_ADDR option from the leftmost 64
bits to the rightmost 64 bits as described in RFC 8684, section 3.4.1.
This issue was discovered while adding support to packetdrill for the
ADD_ADDR v1 option.
Fixes: 3df523ab58 ("mptcp: Add ADD_ADDR handling")
Signed-off-by: Todd Malsbary <todd.malsbary@linux.intel.com>
Acked-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stated in 983695fa67 ("bpf: fix unconnected udp hooks"), the objective
for the existing cgroup connect/sendmsg/recvmsg/bind BPF hooks is to be
transparent to applications. In Cilium we make use of these hooks [0] in
order to enable E-W load balancing for existing Kubernetes service types
for all Cilium managed nodes in the cluster. Those backends can be local
or remote. The main advantage of this approach is that it operates as close
as possible to the socket, and therefore allows to avoid packet-based NAT
given in connect/sendmsg/recvmsg hooks we only need to xlate sock addresses.
This also allows to expose NodePort services on loopback addresses in the
host namespace, for example. As another advantage, this also efficiently
blocks bind requests for applications in the host namespace for exposed
ports. However, one missing item is that we also need to perform reverse
xlation for inet{,6}_getname() hooks such that we can return the service
IP/port tuple back to the application instead of the remote peer address.
The vast majority of applications does not bother about getpeername(), but
in a few occasions we've seen breakage when validating the peer's address
since it returns unexpectedly the backend tuple instead of the service one.
Therefore, this trivial patch allows to customise and adds a getpeername()
as well as getsockname() BPF cgroup hook for both IPv4 and IPv6 in order
to address this situation.
Simple example:
# ./cilium/cilium service list
ID Frontend Service Type Backend
1 1.2.3.4:80 ClusterIP 1 => 10.0.0.10:80
Before; curl's verbose output example, no getpeername() reverse xlation:
# curl --verbose 1.2.3.4
* Rebuilt URL to: 1.2.3.4/
* Trying 1.2.3.4...
* TCP_NODELAY set
* Connected to 1.2.3.4 (10.0.0.10) port 80 (#0)
> GET / HTTP/1.1
> Host: 1.2.3.4
> User-Agent: curl/7.58.0
> Accept: */*
[...]
After; with getpeername() reverse xlation:
# curl --verbose 1.2.3.4
* Rebuilt URL to: 1.2.3.4/
* Trying 1.2.3.4...
* TCP_NODELAY set
* Connected to 1.2.3.4 (1.2.3.4) port 80 (#0)
> GET / HTTP/1.1
> Host: 1.2.3.4
> User-Agent: curl/7.58.0
> Accept: */*
[...]
Originally, I had both under a BPF_CGROUP_INET{4,6}_GETNAME type and exposed
peer to the context similar as in inet{,6}_getname() fashion, but API-wise
this is suboptimal as it always enforces programs having to test for ctx->peer
which can easily be missed, hence BPF_CGROUP_INET{4,6}_GET{PEER,SOCK}NAME split.
Similarly, the checked return code is on tnum_range(1, 1), but if a use case
comes up in future, it can easily be changed to return an error code instead.
Helper and ctx member access is the same as with connect/sendmsg/etc hooks.
[0] https://github.com/cilium/cilium/blob/master/bpf/bpf_sock.c
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/61a479d759b2482ae3efb45546490bacd796a220.1589841594.git.daniel@iogearbox.net
Commit bc56c919fc ("bpf: Add xdp.frame_sz in bpf_prog_test_run_xdp().")
recently changed bpf_prog_test_run_xdp() to use larger frames for XDP in
order to test tail growing frames (via bpf_xdp_adjust_tail) and to have
memory backing frame better resemble drivers.
The commit contains a bug, as it tries to copy the max data size from
userspace, instead of the size provided by userspace. This cause XDP
unit tests to fail sporadically with EFAULT, an unfortunate behavior.
The fix is to only copy the size specified by userspace.
Fixes: bc56c919fc ("bpf: Add xdp.frame_sz in bpf_prog_test_run_xdp().")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/158980712729.256597.6115007718472928659.stgit@firesoul
syzbot found that
touch /proc/testfile
causes NULL pointer dereference at tomoyo_get_local_path()
because inode of the dentry is NULL.
Before c59f415a7c, Tomoyo received pid_ns from proc's s_fs_info
directly. Since proc_pid_ns() can only work with inode, using it in
the tomoyo_get_local_path() was wrong.
To avoid creating more functions for getting proc_ns, change the
argument type of the proc_pid_ns() function. Then, Tomoyo can use
the existing super_block to get pid_ns.
Link: https://lkml.kernel.org/r/0000000000002f0c7505a5b0e04c@google.com
Link: https://lkml.kernel.org/r/20200518180738.2939611-1-gladkov.alexey@gmail.com
Reported-by: syzbot+c1af344512918c61362c@syzkaller.appspotmail.com
Fixes: c59f415a7c ("Use proc_pid_ns() to get pid_namespace from the proc superblock")
Signed-off-by: Alexey Gladkov <gladkov.alexey@gmail.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
To prepare removing the global routing_ioctl hack start lifting the code
into the ipv4 and appletalk ->compat_ioctl handlers. Unlike the existing
handler we don't bother copying in the name - there are no compat issues for
char arrays.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper than can be shared with the upcoming compat ioctl handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare removing the global routing_ioctl hack start lifting the code
into a newly added ipv6 ->compat_ioctl handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for better compat ioctl handling by moving the user copy out
of ipv6_route_ioctl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor: svc_recvfrom() is going to be converted to read into
bio_vecs in a moment. Unhook the only other caller,
svc_tcp_recv_record(), which just wants to read the 4-byte stream
record marker into a kvec.
While we're in the area, streamline this helper by straight-lining
the hot path, replace dprintk call sites with tracepoints, and
reduce the number of atomic bit operations in this path.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up. I find the name of the svc_sock::sk_reclen field
confusing, so I've changed it to better reflect its function. This
field is not read directly to get the record length. Rather, it is
a buffer containing a record marker that needs to be decoded.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Report TCP socket state changes and accept failures via
tracepoints, replacing dprintk() call sites.
No tracepoint is added in svc_tcp_listen_data_ready. There's
no information available there that isn't also reported by the
svcsock_new_socket and the accept failure tracepoints.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
In addition to tracing recently-updated socket sendto events, this
commit adds a trace event class that can be used for additional
svcsock-related tracepoints in subsequent patches.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: Commit 850cbaddb5 ("udp: use it's own memory accounting
schema") removed the last skb-related tracepoint from svcsock.c, so
it is no longer necessary to include trace/events/skb.h.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
In lieu of dprintks or tracepoints in each individual transport
implementation, introduce tracepoints in the generic part of the RPC
layer. These typically fire for connection lifetime events, so
shouldn't contribute a lot of noise.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Failure to accept a connection is typically due to a problem
specific to a transport type. Also, ->xpo_accept returns NULL
on error rather than reporting a specific problem.
So, add failure-specific tracepoints in svc_rdma_accept().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: After commit 1e091c3bbf ("svcrdma: Ignore source port
when computing DRC hash"), the IP address stored in xpt_remote
always has a port number of zero. Thus, there's no need to display
the port number when displaying the IP address of a remote NFS/RDMA
client.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: Use a consistent naming convention so that these trace
points can be enabled quickly via a glob.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Way back when I was writing the RPC/RDMA server-side backchannel
code, I misread the TCP backchannel reply handler logic. When
svc_tcp_recvfrom() successfully receives a backchannel reply, it
does not return -EAGAIN. It sets XPT_DATA and returns zero.
Update svc_rdma_recvfrom() to return zero. Here, XPT_DATA doesn't
need to be set again: it is set whenever a new message is received,
behind a spin lock in a single threaded context.
Also, if handling the cb reply is not successful, the message is
simply dropped. There's no special message framing to deal with as
there is in the TCP case.
Now that the handle_bc_reply() return value is ignored, I've removed
the dprintk call sites in the error exit of handle_bc_reply() in
favor of trace points in other areas that already report the error
cases.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Clean up: Replace a dprintk call site.
This is the last remaining dprintk call site in svc_rdma_rw.c, so
remove dprintk infrastructure as well.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
