I've opened up the case, and the chips in the ATEN UC2324 are:
Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)
(logo with AF kerned together) 0748
24BC02
SINGLP
(unknown 8-pin chip)
(logo looks like 3 or Z in circle)
ZT3243LEEA 0752
B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)
So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver. I expect you will remove the
aten2011.c driver from the staging area.
From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board. This value
should be added to the device id table of mos7840.c.
Here's a patch that adds these devices to the driver.
From: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.
These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: can't setup
orion-ehci orion-ehci.0: USB bus 1 deregistered
orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
orion-ehci: probe of orion-ehci.0 failed with error -110
which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: Ville Sundberg <vsundber@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP: OHCI: hc_driver's stop method should call ohci_stop
Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.
Reported-by: vikram pandita <vikram.pandita@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.
Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.
Signed-off-by: Giacomo Lozito <james@develia.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for compilation without CONFIG_PM.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit f092c24049 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:
drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'
So I removed it.
Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those definitions are already provided by asm-generic
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes
- locking bug that was hidden by ecc2e05e73
- Regression #13821
- Spurious warning when closing and blocking for data write out
With these changes my PL2303 always ends up as ttyUSB0 when it should and
the module refcounts stay correct.
I'll do a more wholesale split & tidy of _open in the next release or two
as we get a standard tty_port_open and port->ops->init port->ops->shutdown
call backs.
Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the
reports but it passes local testing with the same hardware as Alan Stern.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: use GFP_NOFS under potential memory pressure
fsnotify: fix inotify tail drop check with path entries
inotify: check filename before dropping repeat events
fsnotify: use def_bool in kconfig instead of letting the user choose
inotify: fix error paths in inotify_update_watch
inotify: do not leak inode marks in inotify_add_watch
inotify: drop user watch count when a watch is removed
This also makes close stall in the normal case which is apparently
needed to fix emacs
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
cnic: Fix ISCSI_KEVENT_IF_DOWN message handling.
net: irda: init spinlock after memcpy
ixgbe: fix for 82599 errata marking UDP checksum errors
r8169: WakeOnLan fix for the 8168
netxen: reset ring consumer during cleanup
net/bridge: use kobject_put to release kobject in br_add_if error path
smc91x.h: add config for Nomadik evaluation kit
NET: ROSE: Don't use static buffer.
eepro: Read buffer overflow
tokenring: Read buffer overflow
at1700: Read buffer overflow
fealnx: Write outside array bounds
ixgbe: remove unnecessary call to device_init_wakeup
ixgbe: Don't priority tag control frames in DCB mode
ixgbe: Enable FCoE offload when DCB is enabled for 82599
net: Rework mdio-ofgpio driver to use of_mdio infrastructure
register at91_ether using platform_driver_probe
skge: Enable WoL by default if supported
net: KS8851 needs to depend on MII
be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly.
...
The port lock is used to protect the port state. However the port structure
is freed on a hangup, then the lock taken on a close. The right fix is to
drop the port on tty->shutdown() but we can't yet do that due to sleep v
non-sleeping rules. Instead do the next best thing and fix it up when we are
not in -rc season.
Reported-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Makefile cleanup
microblaze: Typo fix for cpu param inconsistency
microblaze: Add support for R_MICROBLAZE_64_NONE
microblaze: Get module loading working
microblaze: remove sys_ipc
microblaze: Support unaligned address for put/get_user macros
microblaze: Detect new Microblaze 7.20 versions
microblaze: Fix do_page_fault for no context
microblaze: Add _PAGE_FILE macros to pgtable.h
microblaze: Fix put_user macro for 64bits arguments
microblaze: Clear print messages for DTB passing via r7
microblaze: Not to clear r7 after copying DTB to kernel
microblaze: Add messages about FDT blob
microblaze: Final support for statically linked DTB
microblaze: remove duplicated #include
microblaze: Define tlb_flush macro
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure
x86, amd: Don't probe for extended APIC ID if APICs are disabled
x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD"
x86-64: Fix bad_srat() to clear all state
x86, mce: Fix set_trigger() accessor
x86: Fix movq immediate operand constraints in uaccess.h
x86: Fix movq immediate operand constraints in uaccess_64.h
x86: Add reboot fixup for SBC-fitPC2
x86: Include all of .data.* sections in _edata on 64-bit
x86: Add quirk for Intel DG45ID board to avoid low memory corruption
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix mute control with some ALC262 models
ALSA: snd_usb_caiaq: add support for Audio2DJ
ALSA: pcm - Fix hwptr buffer-size overlap bug
ALSA: pcm - Fix warnings in debug loggings
ALSA: pcm - Add logging of hwptr updates and interrupt updates
ASoC: tlv320aic3x: Enable PLL when not bypassed
ALSA: hda - Restore GPIO1 properly at resume with AD1984A
ALSA: ctxfi - Fix uninitialized error checks
ALSA: hda - Use snprintf() to be safer
ALSA: usb-audio - Volume control quirk for QuickCam E 3500
ALSA: pcm - Fix regressions with VMware
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (34 commits)
V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macro
V4L/DVB (12302): cx23885-417: fix broken IOCTL handling
V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tuner
V4L/DVB (12291): b2c2: fix frontends compiled into kernel
V4L/DVB (12286): sn9c20x: reorder includes to be like other drivers
V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg header).
V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges.
V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and vidioc_g/s_register.
V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by app
V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors.
V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1)
V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e
V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used
V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support
V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881)
V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB
V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant)
V4L/DVB (12245): em28xx: add support for mt9m001 webcams
V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format
V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency
...
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: fix scheduling of hrtimer ap_poll_timer
[S390] vdso: clock_gettime of CLOCK_THREAD_CPUTIME_ID with noexec=on
[S390] vdso: fix per cpu area allocation
[S390] hibernation: fix register corruption on machine checks
[S390] hibernation: fix lowcore handling
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm table: pass correct dev area size to device_area_is_valid
dm: remove queue next_ordered workaround for barriers
dm raid1: wake kmirrord when requeueing delayed bios after remote recovery
Commit 63706172f3 ("kthreads: rework
kthread_stop()") removed the limitation that the thread function mysr
not call do_exit() itself, but forgot to update the comment.
Since that commit it is OK to use kthread_stop() even if kthread can
exit itself.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check_modstruct_version() needs to look up the symbol "module_layout"
in the kernel, but it does so literally and not by a C identifier. The
trouble is that it does not include a symbol prefix for those ports that
need it (like the Blackfin and H8300 port). So make sure we tack on the
MODULE_SYMBOL_PREFIX define to the front of it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
jbd: fix race between write_metadata_buffer and get_write_access
ext3: Get rid of extenddisksize parameter of ext3_get_blocks_handle()
jbd: Fix a race between checkpointing code and journal_get_write_access()
ext3: Fix truncation of symlinks after failed write
jbd: Fail to load a journal if it is too short
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] fix sparse warning
cifs: fix sb->s_maxbytes so that it casts properly to a signed value
cifs: disable serverino if server doesn't support it
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a net device goes down or when the bnx2i driver is unloaded,
the code was not generating the ISCSI_KEVENT_IF_DOWN message
properly and this could cause the userspace driver to crash.
This is fixed by sending the message properly in the shutdown path.
cnic_uio_stop() is also added to send the message when bnx2i is
unregistering.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irttp_dup() copies a tsap_cb struct, but does not initialize the
spinlock in the new structure, which confuses lockdep.
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed the Makefile on request by Michal and this is the resulting changes.
o Use ':=' for assignmnet so we do not re-evaluate for each use
o Use $(shell echo xxx) to remove ""
o Replaced CFLAGS_KERNEL with KBUILD_CFLAGS
The settings are equally relevant for modules and the linked kernel
o Dropped LDFLAGS_BLOB - it is no longer used
o Refactored assignmnets to libs-y and core-y
o Use MMU for the MMU specific extension. "MMUEXT" was hurting my eyes
and I did not wanted it spread to m68k
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
New reloc type R_MICROBLAZE_32_PCREL_LO requires a null handler (no work to do).
Remove legacy hack for broken linker pre gcc-4.1.1, that required us to extract
an offset from the code, add it to the addend, then rewrite the instruction.
Fixup the invalid reloc type error output.
Boot tested with the xilinx_emaclite ethernet driver.
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The ipc system call is now unused in microblaze,
as the system call table points directly to the
indidual system calls for IPC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch add support for cases where load/store instruction
in put/get_user macro gets unaligned pointer to data and this
address is not valid. I prevent all cases which can failed.
I had to disable first stage of unaligned handler which is used
only for noMMU kernel and the whole work is done when interrupt
is enabled.
You have enable HW support for detect unaligned access in Microblaze.
This patch fixed three LTP tests:
getpeername01, getsockname01, socketpair01
Signed-off-by: Michal Simek <monstr@monstr.eu>
Calling fixup when we are in kernel mode. This
prevent fault for copy_to/from_user. This fault
was find thanks to writev01/03/04 LTP tests.
Signed-off-by: Michal Simek <monstr@monstr.eu>
We need to define _PAGE_FILE macro and change pte
functions. Microblaze use the same MMU as PowerPC
that's why we define _PAGE_FILE in the same style.
This change fixed remap_file_pages01 LTP test.
Signed-off-by: Michal Simek <monstr@monstr.eu>
For 64bits arguments gcc caused that put_user macro
works with wrong value because of optimalization.
Adding volatile caused that gcc not optimized it.
It is possible to use (as Blackfin do) two put_user
macros with 32bits arguments but there is one more
instruction which is due to duplication zero return
value which is called put_user_asm macro.
Signed-off-by: Michal Simek <monstr@monstr.eu>
It is necessary to zeroed r7 when r7 points to bad
dtb - this caused that we have correct messages
about compiled-in dtb or passing via r7
Signed-off-by: Michal Simek <monstr@monstr.eu>
If r7 is zero at kernel boot, or does not point to a valid DTB, then
we fall back to a DTB (assumed to be) linked statically in the kernel, instead
of blindly copying bogus cruft into the kernel DTB memory region
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This fix remove bug which we had till now in all
Microblaze MMU code. Primary tested on mmap01 LTP test.
We forget to flush invalid tlb which were changed - we
used them and there were wrong old data which wasn't correct.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading hw_csum_rx_error counts. This patch adds a
test around this counter increase for this condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
