[ Upstream commit 6d9459d040 ]
CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.
Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.
In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b0d ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8ee6c8cb6 ]
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89dd87acd4 ]
If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from
ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync()
and ufshcd_hold() will cause a race condition. Fix this by removing the
unnecessary calls of pm_runtime_get_sync() and ufshcd_hold().
Link: https://lore.kernel.org/r/1596975355-39813-3-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbc299437c ]
usb_kill_anchored_urbs() is commonly used to cancel all URBs on an
anchor just before releasing resources which the URBs rely on. By doing
so, users of this function rely on that no completer callbacks will take
place from any URB on the anchor after it returns.
However if this function is called in parallel with __usb_hcd_giveback_urb
processing a URB on the anchor, the latter may call the completer
callback after usb_kill_anchored_urbs() returns. This can lead to a
kernel panic due to use after release of memory in interrupt context.
The race condition is that __usb_hcd_giveback_urb() first unanchors the URB
and then makes the completer callback. Such URB is hence invisible to
usb_kill_anchored_urbs(), allowing it to return before the completer has
been called, since the anchor's urb_list is empty.
Even worse, if the racing completer callback resubmits the URB, it may
remain in the system long after usb_kill_anchored_urbs() returns.
Hence list_empty(&anchor->urb_list), which is used in the existing
while-loop, doesn't reliably ensure that all URBs of the anchor are gone.
A similar problem exists with usb_poison_anchored_urbs() and
usb_scuttle_anchored_urbs().
This patch adds an external do-while loop, which ensures that all URBs
are indeed handled before these three functions return. This change has
no effect at all unless the race condition occurs, in which case the
loop will busy-wait until the racing completer callback has finished.
This is a rare condition, so the CPU waste of this spinning is
negligible.
The additional do-while loop relies on usb_anchor_check_wakeup(), which
returns true iff the anchor list is empty, and there is no
__usb_hcd_giveback_urb() in the system that is in the middle of the
unanchor-before-complete phase. The @suspend_wakeups member of
struct usb_anchor is used for this purpose, which was introduced to solve
another problem which the same race condition causes, in commit
6ec4147e7b ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up
till completion is done").
The surely_empty variable is necessary, because usb_anchor_check_wakeup()
must be called with the lock held to prevent races. However the spinlock
must be released and reacquired if the outer loop spins with an empty
URB list while waiting for the unanchor-before-complete passage to finish:
The completer callback may very well attempt to take the very same lock.
To summarize, using usb_anchor_check_wakeup() means that the patched
functions can return only when the anchor's list is empty, and there is
no invisible URB being processed. Since the inner while loop finishes on
the empty list condition, the new do-while loop will terminate as well,
except for when the said race condition occurs.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200731054650.30644-1-eli.billauer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c151410d5 ]
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL,
we should destroy the workqueue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595237765-66238-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e68cccc8e ]
Eliminate kernel panics when getting invalid responses from controller.
Take controller offline instead of causing kernel panics.
Link: https://lore.kernel.org/r/159622929306.30579.16523318707596752828.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed93f9750c ]
Add AE-7 quirk data for setting of microphone. The AE-7 has no front
panel connector, so only rear-mic/line-in have new commands.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20200825201040.30339-19-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621a3a8b1c ]
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
[1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959
[2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com
Reported-by: syzbot <syzbot+dc4127f950da51639216@syzkaller.appspotmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821082720.7716-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9d4709fcc ]
When a usrjquota or grpjquota mount option is used multiple times, we
will leak memory allocated for the file name. Make sure the last setting
is used and all the previous ones are properly freed.
Reported-by: syzbot+c9e294bbe0333a6b7640@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d33fe77bdf ]
When kmalloc() on buf fails, urb should be freed just like
when kmalloc() on dr fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db33235622 ]
ipwireless_send_packet() can only return 0 on success and -ENOMEM on
error, the caller should check non zero for error condition
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a49145acfb ]
A fb_ioctl() FBIOPUT_VSCREENINFO call with invalid xres setting
or yres setting in struct fb_var_screeninfo will result in a
KASAN: vmalloc-out-of-bounds failure in bitfill_aligned() as
the margins are being cleared. The margins are cleared in
chunks and if the xres setting or yres setting is a value of
zero upto the chunk size, the failure will occur.
Add a margin check to validate xres and yres settings.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: syzbot+e5fd3e65515b48c02a30@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dhaval Giani <dhaval.giani@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1594149963-13801-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b35d17f9 ]
While aborting the I/O, the firmware cleanup task timed out and driver
deleted the I/O from active command list. Some time later the firmware
sent the cleanup task response and driver again deleted the I/O from
active command list causing firmware to send completion for non-existent
I/O and list_del corruption of active command list.
Add fix to check if I/O is present before deleting it from the active
command list to ensure firmware sends valid I/O completion and protect
against list_del corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-4-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0650e2844 ]
Protect active command list for non-I/O commands like login response,
logout response, text response, and recovery cleanup of active list to
avoid list corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-5-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10aff62fab ]
If SUCCESS is not returned, error handling will escalate. Return SUCCESS
similar to other conditions in this function.
Link: https://lore.kernel.org/r/20200907121443.5150-6-jhasan@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bf2f2f331 ]
The Acer One S1003 2-in-1 keyboard dock uses a Synaptics S910xx touchpad
which is connected to an ITE 8910 USB keyboard controller chip.
This keyboard has the same quirk for its rfkill / airplane mode hotkey as
other keyboards with ITE keyboard chips, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds this keyboards USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard. Note that like for the
Acer Aspire Switch 10 (SW5-012) the id-table entry matches on the
HID_GROUP_GENERIC generic group so that hid-ite only binds to the
keyboard interface and the mouse/touchpad interface is left untouched
so that hid-multitouch can bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e219688fc5 ]
If a response to virtio_gpu_cmd_get_capset_info takes longer than
five seconds to return, the callback will access freed kernel memory
in vg->capsets.
Signed-off-by: Doug Horn <doughorn@google.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200902210847.2689-2-gurchetansingh@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86279456a4 ]
Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4443293d7 ]
When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908121743.23108-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fb5eefd76 ]
Andrii reported that with latest clang, when building selftests, we have
error likes:
error: progs/test_sysctl_loop1.c:23:16: in function sysctl_tcp_mem i32 (%struct.bpf_sysctl*):
Looks like the BPF stack limit of 512 bytes is exceeded.
Please move large on stack variables into BPF per-cpu array map.
The error is triggered by the following LLVM patch:
https://reviews.llvm.org/D87134
For example, the following code is from test_sysctl_loop1.c:
static __always_inline int is_tcp_mem(struct bpf_sysctl *ctx)
{
volatile char tcp_mem_name[] = "net/ipv4/tcp_mem/very_very_very_very_long_pointless_string";
...
}
Without the above LLVM patch, the compiler did optimization to load the string
(59 bytes long) with 7 64bit loads, 1 8bit load and 1 16bit load,
occupying 64 byte stack size.
With the above LLVM patch, the compiler only uses 8bit loads, but subregister is 32bit.
So stack requirements become 4 * 59 = 236 bytes. Together with other stuff on
the stack, total stack size exceeds 512 bytes, hence compiler complains and quits.
To fix the issue, removing "volatile" key word or changing "volatile" to
"const"/"static const" does not work, the string is put in .rodata.str1.1 section,
which libbpf did not process it and errors out with
libbpf: elf: skipping unrecognized data section(6) .rodata.str1.1
libbpf: prog 'sysctl_tcp_mem': bad map relo against '.L__const.is_tcp_mem.tcp_mem_name'
in section '.rodata.str1.1'
Defining the string const as global variable can fix the issue as it puts the string constant
in '.rodata' section which is recognized by libbpf. In the future, when libbpf can process
'.rodata.str*.*' properly, the global definition can be changed back to local definition.
Defining tcp_mem_name as a global, however, triggered a verifier failure.
./test_progs -n 7/21
libbpf: load bpf program failed: Permission denied
libbpf: -- BEGIN DUMP LOG ---
libbpf:
invalid stack off=0 size=1
verification time 6975 usec
stack depth 160+64
processed 889 insns (limit 1000000) max_states_per_insn 4 total_states
14 peak_states 14 mark_read 10
libbpf: -- END LOG --
libbpf: failed to load program 'sysctl_tcp_mem'
libbpf: failed to load object 'test_sysctl_loop2.o'
test_bpf_verif_scale:FAIL:114
#7/21 test_sysctl_loop2.o:FAIL
This actually exposed a bpf program bug. In test_sysctl_loop{1,2}, we have code
like
const char tcp_mem_name[] = "<...long string...>";
...
char name[64];
...
for (i = 0; i < sizeof(tcp_mem_name); ++i)
if (name[i] != tcp_mem_name[i])
return 0;
In the above code, if sizeof(tcp_mem_name) > 64, name[i] access may be
out of bound. The sizeof(tcp_mem_name) is 59 for test_sysctl_loop1.c and
79 for test_sysctl_loop2.c.
Without promotion-to-global change, old compiler generates code where
the overflowed stack access is actually filled with valid value, so hiding
the bpf program bug. With promotion-to-global change, the code is different,
more specifically, the previous loading constants to stack is gone, and
"name" occupies stack[-64:0] and overflow access triggers a verifier error.
To fix the issue, adjust "name" buffer size properly.
Reported-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200909171542.3673449-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0014f9421 ]
Emit a warning when ->done or ->free are called on an already freed
srb. There is a hidden use-after-free bug in the driver which corrupts
the srb memory pool which originates from the cleanup callbacks.
An extensive search didn't bring any lights on the real problem. The
initial fix was to set both pointers to NULL and try to catch invalid
accesses. But instead the memory corruption was gone and the driver
didn't crash. Since not all calling places check for NULL pointer, add
explicitly default handlers. With this we workaround the memory
corruption and add a debug help.
Link: https://lore.kernel.org/r/20200908081516.8561-2-dwagner@suse.de
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a805c11165 ]
It is trivial to trigger a WARN_ON_ONCE(1) in iomap_dio_actor() by
unprivileged users which would taint the kernel, or worse - panic if
panic_on_warn or panic_on_taint is set. Hence, just convert it to
pr_warn_ratelimited() to let users know their workloads are racing.
Thank Dave Chinner for the initial analysis of the racing reproducers.
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08d3ab4b46 ]
It's allocating an array of a6xx_gpu_state_obj structure rathor than
its pointers.
This patch fix it.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b77d2a0a22 ]
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a6ca4baed ]
There's an overflow bug in the realtime allocator. If the rt volume is
large enough to handle a single allocation request that is larger than
the maximum bmap extent length and the rt bitmap ends exactly on a
bitmap block boundary, it's possible that the near allocator will try to
check the freeness of a range that extends past the end of the bitmap.
This fails with a corruption error and shuts down the fs.
Therefore, constrain maxlen so that the range scan cannot run off the
end of the rt bitmap.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb60e9602c ]
If dev_pm_opp_attach_genpd() is called multiple times (once for each CPU
sharing the table), then it would result in unwanted behavior like
memory leak, attaching the domain multiple times, etc.
Handle that by checking and returning earlier if the domains are already
attached. Now that dev_pm_opp_detach_genpd() can get called multiple
times as well, we need to protect that too.
Note that the virtual device pointers aren't returned in this case, as
they may become unavailable to some callers during the middle of the
operation.
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8859bf2b12 ]
unlock_new_inode() is only meant to be called after a new inode has
already been inserted into the hash table. But reiserfs_new_inode() can
call it even before it has inserted the inode, triggering the WARNING in
unlock_new_inode(). Fix this by only calling unlock_new_inode() if the
inode has the I_NEW flag set, indicating that it's in the table.
This addresses the syzbot report "WARNING in unlock_new_inode"
(https://syzkaller.appspot.com/bug?extid=187510916eb6a14598f7).
Link: https://lore.kernel.org/r/20200628070057.820213-1-ebiggers@kernel.org
Reported-by: syzbot+187510916eb6a14598f7@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc28369c61 ]
When mfd_add_devices() fail, pcr->slots should also be freed. However,
the current implementation does not free the member, leading to a memory
leak.
Fix this by adding a new goto label that frees pcr->slots.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Link: https://lore.kernel.org/r/20200909071853.4053-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f6e4312e1 ]
Protect against potential stack overflow that might happen when bpf2bpf
calls get combined with tailcalls. Limit the caller's stack depth for
such case down to 256 so that the worst case scenario would result in 8k
stack size (32 which is tailcall limit * 256 = 8k).
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1100030022 ]
The T820, G31 & G52 GPUs integrated by Amlogic in the respective GXM,
G12A/SM1 & G12B SoCs needs a quirk in the PWR registers at the GPU reset
time.
Since the Amlogic's integration of the GPU cores with the SoC is not
publicly documented we do not know what does these values, but they
permit having a fully functional GPU running with Panfrost.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Steven: Fix typo in commit log]
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200916150147.25753-3-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad02c7f4f ]
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 960c7339de ]
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee755732b7 ]
The vht capability of MAX_MPDU_LENGTH is 11454 in rtw88; however, the rx
buffer size for each packet is 8192. When receiving packets that are
larger than rx buffer size, it will leads to rx buffer ring overflow.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-2-tehuang@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 044e2e26f2 ]
When we fail to read inode, some data accessed in udf_evict_inode() may
be uninitialized. Move the accesses to !is_bad_inode() branch.
Reported-by: syzbot+91f02b28f9bb5f5f1341@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44ac6b829c ]
Although UDF standard allows it, we don't support sparing table larger
than a single block. Check it during mount so that we don't try to
access memory beyond end of buffer.
Reported-by: syzbot+9991561e714f597095da@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f580170f13 ]
SPLIT_BOUNDARY_DISABLE should be set for DesignWare USB3 DRD Core
of Hisilicon Kirin Soc when dwc3 core act as host.
[mchehab: dropped a dev_dbg() as only traces are now allowwed on this driver]
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc1a267986 ]
Since struct _mic_vring_info and vring are allocated together and follow
vring, if the vring_size() is not four bytes aligned, which will cause
the start address of struct _mic_vring_info is not four byte aligned.
For example, when vring entries is 128, the vring_size() will be 5126
bytes. The _mic_vring_info struct layout in ddr looks like:
0x90002400: 00000000 00390000 EE010000 0000C0FF
Here 0x39 is the avail_idx member, and 0xC0FFEE01 is the magic member.
When EP use ioread32(magic) to reads the magic in RC's share memory, it
will cause kernel panic on ARM64 platform due to the cross-byte io read.
Here read magic in user space use le32toh(vr0->info->magic) will meet
the same issue.
So add round_up(x,4) for vring_size, then the struct _mic_vring_info
will store in this way:
0x90002400: 00000000 00000000 00000039 C0FFEE01
Which will avoid kernel panic when read magic in struct _mic_vring_info.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929091106.24624-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7010645ba7 ]
trace-cmd report doesn't show events from target subsystem because
scsi_command_size() leaks through event format string:
[target:target_sequencer_start] function scsi_command_size not defined
[target:target_cmd_complete] function scsi_command_size not defined
Addition of scsi_command_size() to plugin_scsi.c in trace-cmd doesn't
help because an expression is used inside TP_printk(). trace-cmd event
parser doesn't understand minus sign inside [ ]:
Error: expected ']' but read '-'
Rather than duplicating kernel code in plugin_scsi.c, provide a dedicated
field for CONTROL byte.
Link: https://lore.kernel.org/r/20200929125957.83069-1-r.bolshakov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 055f15ab2c ]
Return PTR_ERR() from the error handling case instead of 0.
Link: https://lore.kernel.org/r/20200910123848.93649-1-jingxiangfeng@huawei.com
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 428805c0c5 ]
get_gendisk grabs a reference on the disk and file operation, so this
code will leak both of them while having absolutely no use for the
gendisk itself.
This effectively reverts commit 2df83fa4bc ("PM / Hibernate: Use
get_gendisk to verify partition if resume_file is integer format")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b783d104e ]
Even though a driver or mac80211 shouldn't produce a
legacy bitrate if sband->bitrates doesn't exist, don't
crash if that is the case either.
This fixes a kernel panic if station dump is run before
last_rate can be updated with a data frame when
sband->bitrates is missing (eg. in S1G bands).
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdafed4599 ]
GRE tunnel has its own header_ops, ipgre_header_ops, and sets it
conditionally. When it is set, it assumes the outer IP header is
already created before ipgre_xmit().
This is not true when we send packets through a raw packet socket,
where L2 headers are supposed to be constructed by user. Packet
socket calls dev_validate_header() to validate the header. But
GRE tunnel does not set dev->hard_header_len, so that check can
be simply bypassed, therefore uninit memory could be passed down
to ipgre_xmit(). Similar for dev->needed_headroom.
dev->hard_header_len is supposed to be the length of the header
created by dev->header_ops->create(), so it should be used whenever
header_ops is set, and dev->needed_headroom should be used when it
is not set.
Reported-and-tested-by: syzbot+4a2c52677a8a1aa283cb@syzkaller.appspotmail.com
Cc: William Tu <u9012063@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Serge Semin