Egil Hjelmeland says:
====================
net: dsa: lan9303: Fix STP and flooding issues
This patch set finishes the STP support, and fixes flooding issues.
Patch 1 fixes a flooding issue in the previous patch set.
Patch 2 finishes STP support by adding a ALR entry.
Patch 3 prevent duplicate flooding in HW and SW bridge.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.
One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.
This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment to pointer msg is redundant as it is never read, so
remove msg. Also remove the first assignment to qset as this is not
read before the next re-assignment of a new value to qset in the
for-loop. Cleans up two clang warnings:
drivers/net/ethernet/cavium/thunder/nic_main.c:589:2: warning: Value
stored to 'msg' is never read
drivers/net/ethernet/cavium/thunder/nic_main.c:611:2: warning: Value
stored to 'qset' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the best place in MAINTAINERS data base to cover this
orphaned module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet FCS inclusion (rx-fcs) is supported on EF10 NICs, conditional on
a firmware capability bit (MC_CMD_GET_CAPABILITIES_OUT_RX_INCLUDE_FCS).
To receive frames with bad FCS (rx-all) we just don't return the discard
flag EFX_RX_PKT_DISCARD from efx_ef10_handle_rx_event_errors() or
efx_farch_handle_rx_not_ok().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable work_done is set to zero and this value is never read, instead
it is set to another value a few statements later. Remove the redundant
assignment. Cleans up clang warning:
drivers/net/ethernet/cadence/macb_main.c:1221:2: warning: Value stored
to 'work_done' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reported breakages of VRF scenarios due to the
commit 6e617de84e ("net: avoid a full fib lookup when rp_filter is
disabled."): the local addresses based test is too strict when VRFs
are in place.
With this change we fall-back to a full lookup when custom fib rules
are in place; so that we address the VRF use case and possibly other
similar issues in non trivial setups.
v1 -> v2:
- fix build breakage when CONFIG_IP_MULTIPLE_TABLES is not defined,
reported by the kbuild test robot
Reported-by: David Ahern <dsahern@gmail.com>
Fixes: 6e617de84e ("net: avoid a full fib lookup when rp_filter is disabled.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to returnerror code -ENOMEM from the sctp_make_strreset_addstrm()
error handling case instead of 0. 'retval' can be overwritten to 0 after
call sctp_stream_alloc_out().
Fixes: e090abd0d8 ("sctp: factor out stream->out allocation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer dev is being assigned but is never used, hence it is
redundant and can be removed. Cleans up clang warning:
drivers/net/usb/hso.c:2280:2: warning: Value stored to 'dev' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mutex_destroy only makes sense when enable DEBUG_MUTEX. For the
good readbility, it's better to invoke it in exit func when the init
func invokes mutex_init.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable idx is being initialized and later on over-written by
a new value in a do-loop without the initial value ever being
read. Hence the initializion is redundant and can be removed.
Cleans up clang warning:
drivers/net/ethernet/alacritech/slicoss.c:358:15: warning: Value
stored to 'idx' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
PHYLINK cosmetic and build fixes
Please find two small "fixes" one that corrects some stylistic changes and
another one that fixes an actual build failure in sfp.c. Since PHYLINK is
not directly visible to user, and there are no in-tree users yet (coming)
this is not targeted at "net" but "net-next" instead.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
include/gpio.h does not contain the references we want, we should be including
linux/gpio/consumer.h instead.
Fixes: 7397005545 ("sfp: add SFP module support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform a number of stylistic changes to phylink.c, sfp.c and sfp-bus.c:
- align with netdev-style comments
- align function arguments to the opening parenthesis
- remove blank lines
- fixup a few lines over 80 columns
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to address common misconceptions about what BPF is and what it's not
add short BPF Q&A that clarifies core BPF design principles and
answers some common questions.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the error messages displayed in kernel log to include
hwaddress of the source machine that caused ipv6 duplicate address
detection failures.
Examples:
a) When we receive a NA packet from another machine advertising our
address:
ICMPv6: NA: 34🆎cd:56:11:e8 advertised our address 2001:db8:: on eth0!
b) When we detect DAD failure during address assignment to an interface:
IPv6: eth0: IPv6 duplicate address 2001:db8:: used by 34🆎cd:56:11:e8
detected!
v2:
Changed %pI6 to %pI6c in ndisc_recv_na()
Chaged the v6 address in the commit message to 2001:db8::
Suggested-by: Igor Lubashev <ilubashe@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have b53_hdr_setup() check what kind of tagging protocol is configured
(Broadcom or none) and apply the correct settings in both cases.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva says:
====================
netrom: refactor code and mark expected switch fall-throughs
The aim of this patchset is firstly to refactor code in nr_route.c in order to make it
easier to read and maintain and, secondly, to mark some expected switch fall-throughs
in preparation to enabling -Wimplicit-fallthrough.
I have to mention that I did not implement any unit test.
If someone has any suggestions on how I could test this piece of code
it'd be greatly appreciated.
Changes in v2:
- Make use of the swap macro and remove inline keyword as suggested by
Walter Harms and Kevin Dawson.
Changes in v3:
- Update subject for both patches.
- Add this cover letter as suggested by David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code refactoring in order to make the code easier to read and maintain.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: linux-ntb@googlegroups.com
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During perf event attaching/detaching bpf programs,
the tp_event->prog_array change is protected by the
bpf_event_mutex lock in both attaching and deteching
functions. Although tp_event->prog_array is a rcu
pointer, rcu_derefrence is not needed to access it
since mutex lock will guarantee ordering.
Verified through "make C=2" that sparse
locking check still happy with the new change.
Also change the label name in perf_event_{attach,detach}_bpf_prog
from "out" to "unlock" to reflect the code action after the label.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using SIT tunnels with VRFs works fine if the underlay device is in a
VRF and the link parameter is set to the VRF device. e.g.,
ip tunnel add jtun mode sit remote <addr> local <addr> dev myvrf
Update the device check to allow the link to be the enslaved device as
well. e.g.,
ip tunnel add jtun mode sit remote <addr> local <addr> dev eth4
where eth4 is enslaved to myvrf.
Reported-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for IFLA_BRPORT_NEIGH_SUPPRESS to bridge port policies.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: mvpp2: various improvements
This series includes various patches improving the Marvell PPv2 driver.
I send them as a series to avoid any possible merge conflict.
- Patches 1 and 2 improve the initializing of the Tx and Rx FIFO.
- Patch 3 initialize the RSS table to evenly distribute the ingress
packets across multiple Rx queues based on their hashes.
- Patch 4 limits the number of TSO segments sent to the driver, to avoid
having more segments to handle than the corresponding number of
available descriptors.
- Patch 5 and 6 are cosmetic improvements.
This applies on today's net-next branch, The patches were tested
extensively (I ran iperf and http downloads in parallel, transferring
TBs of data).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two functions were always used to set the DMA addresses in Tx
descriptors, because this address is split into a base+offset in the
descriptors. A mask was used to come up with the base and offset
addresses and two functions were called, mvpp2_txdesc_dma_addr_set() and
mvpp2_txdesc_offset_set().
This patch moves the base+offset calculation logic to
mvpp2_txdesc_dma_addr_set(), and removes mvpp2_txdesc_offset_set() to
simplify things.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch using the MVPP2_AGGR_TXQ_SIZE everywhere instead of the
size field of aggr_txq, as the size never change and is always equal to
the MVPP2_AGGR_TXQ_SIZE define.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many TSO descriptors can be required for the default queue size,
when using small MSS values for example. Prevent this by adding a
maximum number of allowed TSO segments (300). In addition set a stop and
a wake thresholds to stop the queue when there's no room for a 1 "worst
case scenario skb". Wake up the queue when the number of descriptors is
low enough.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initialize the RSS tables to evenly (depending on the packets
RSS hashes) distribute the packets across port Rx queues. This helps to
handle packets on different CPUs to improve performances, as more queues
will be used in parallel.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the Rx FIFO size was initialized. For PPv2.2 the Tx FIFO
size can be set as well. This patch initializes the Tx FIFO size for
PPv2.2 controllers to 3K.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx FIFO size was set to the same value for all ports. This patch
sets it depending on the maximum speed a given port can handle. This is
only working for PPv2.2.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-10-30
1) Change some variables that can't be negative
from int to unsigned int. From Alexey Dobriyan.
2) Remove a redundant header initialization in esp6.
From Colin Ian King.
3) Some BUG to BUG_ON conversions.
From Gustavo A. R. Silva.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable len is being assigned a value that is never read,
hence the assignment is redundant and can be removed. Cleans
up clang warning:
drivers/net/hamradio/mkiss.c:443:3: warning: Value stored to
'len' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sockmap test is using two programs that use bpf_trace_printk()
which prints into trace_pipe, but nothing is reading it.
Remove it.
Fixes: 6f6d33f3b3 ("bpf: selftests add sockmap tests")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions pci_alloc_consistent is obsolete. So it is replaced
with dma_alloc_coherent
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipip and gre, ip_vti never uses err_count in vti4_err,
so no need to check err_count in vti_xmit, it's value always 0.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Allow non-fatal messages to be passed in extack
There are many cases where networking subsystems throw non-fatal warning
messages that end up in dmesg / kernel log to which a user making the
change is completely oblivious. This set makes the extack facility
usable for returning such messages.
The case in point here is spectrum and adding FIB rules which causes an
offload abort. Make the use case more user friendly by letting the user
know that offload is no longer happening because of the rule change.
v2
- kept the offload abort in a work queue entry per Ido's comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a FIB rule on a spectrum platform silently aborts FIB offload:
$ ip ru add pref 99 from all to 192.168.1.1 table 10
$ dmesg -c
[ 623.144736] mlxsw_spectrum 0000:03:00.0: FIB abort triggered. Note that FIB entries are no longer being offloaded to this device.
This patch reworks FIB rule handling to return a message to the user:
$ ip ru add pref 99 from all to 8.8.8.8 table 11
Error: spectrum: FIB rules not supported. Aborting offload.
spectrum currently only checks whether the fib rule is a default rule or
an l3mdev rule, both of which it knows how to handle. Any other it aborts
FIB offload. Move the processing to check the rule type inline with the
user request. If the rule is an unsupported one, then a work queue entry
is used to abort the offload. Change the rule delete handling to just
return since it does nothing at the moment.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack to fib_notifier_info and plumb through stack to
call_fib_rule_notifiers, call_fib_entry_notifiers and
call_fib6_entry_notifiers. This allows notifer handlers to
return messages to user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLMSGERR API already carries data (eg, a cookie) on the success path.
Allow a message string to be returned as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: add port parsing functions
This patchset adds port parsing functions called early in the new
bindings parsing stage, which regroup all the fetching of static data
available at the port level, including the port's type, name and CPU
master interface.
This simplifies the rest of the code which does not need to dig into
device tree or platform data again in order to check a port's type or
name.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
