Define the HLCDC (HLCD Controller) IP available on some sama5d3 SoCs
(i.e. sama5d31, sama5d33, sama5d34 and sama5d36) in sama5d3 dtsi file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define alternative pin muxing for the LCDC pins.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The HLCDC (HLCD Controller) IP supports 4 different output mode (RGB444,
RGB565, RGB666 and RGB888) and the pin muxing will depend on the chosen
RGB mode.
Split pin definitions to be able to set pin config according to the
selected mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update dts file to reflect:-
* new flash memory layout
* add missing phy-mode property
* dual_emac now just a boolean
* rename mcp to microchip
* update gpio definition
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the primary camera of the Nokia N950 and N9.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The resources the ISP needs are slightly different on 3[45]xx and 3[67]xx.
Especially the phy-type property is different.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: use omap3_scm_general instead of scm_conf for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This L2 controller handles multiplexing a few different interrupts. We
also need it for configuring the interrupt forwarding masks for the
UART.
With this, we can *now* boot BCM7445 to a prompt using the upstream
kernel + DTB.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
These files are not used by any DTS file anymore.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This value makes much more sense in decimal.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch just move content of file omap34xx-hs.dtsi into omap3-tao3530.dts.
There is no code change, patch is just preparation for removing -hs file.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves content of file omap34xx-hs.dtsi into omap3-n900.dts and enable
omap sham support (omap HW support for SHA + MD5). After testing both omap hwmod
and omap-sham.ko drivers it looks like signed Nokia X-Loader enable L3 firewall
for omap sham. There is no kernel crash with both official bootloader and crypto
enable bootloader. So we can safely enable sham code.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Harmattan system on Nokia N9 and N950 devices uses omap crypto support.
Bootloader on those devices is known that it enables HW crypto support.
This patch just include omap36xx.dtsi directly, so aes and sham is enabled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On dm816x we have no PIN_INPUT vs PIN_OUTPUT configuration, there
are just pulls. Let's remove the bogus flags.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we have cppi41 on dm816x just like on am335x.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a54879a008 ("ARM: dts: Fix USB dts configuration for dm816x")
attempted to fix the USB features introduced by commit 7800064ba5
("ARM: dts: Add basic dm816x device tree configuration") but obviously
I did not read the dmesg as more USB issues still keep trickling in.
It should be usb1_pins instead not usb0_pins for the second interface
to avoid warnings from pinctrl framework.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The socfpga.dtsi currently has the wrong interrupt number set for SPI master 1
Trying to use the master without this change results in the kernel boot
process waiting forever for an interrupt that will never occur while
attempting to probe any slave devices configured in the device tree as being
under SPI master 1.
The change works for the Cyclone V, and according to the Arria 5 handbook
should be good there too.
Signed-off-by: Mark James <maj@jamers.net>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
For L2 cache controller node, cache-level property is mandatory. Let's
add it to Armada 370 and Armada XP device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The resources of the cpuclk node are overlapping the one from
coredivclk node. It was not noticed until now because the driver did a
simple of_iomap and not a request_mem_region. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and port to 4.0-rc]
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.
This turned out several issues that need to be fixed:
- I set the GPIO type wrong to be compatible with omap3 instead
of omap4. The GPIO controller on dm816x has EOI interrupt
register like omap4 and am335x.
- I got the GPIO interrupt numbers wrong as each bank has two
and we only use one. They need to be set up the same way as
on am335x.
- The gpio banks are missing interrupt controller related
properties.
With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.
For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we don't have hwmod entry for pcie PHY remove the
ti,hwmod property from PCIE PHY's. Otherwise we will get:
platform 4a094000.pciephy: Cannot lookup hwmod 'pcie1-phy'
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Exynos has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the PMU block is actually the first
interrupt controller in the chain for RTC, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs may not even boot.
Also, I strongly suspect that there is more than two wake-up
interrupts on these platforms, but I leave it to the maintainers
to fix their mess.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088693-15724-2-git-send-email-marc.zyngier@arm.com
[ jac: squash in maz's fixup from
https://lkml.kernel.org/r/5506989D.9050703@arm.com ]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 385 AP board has a USB3 port exposed that uses a GPIO to drive the
VBUS line. Enable the needed drivers to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c4 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Both GSCALER IPs in gsc power domain have async-bridges (to FIMD and MIXER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
FIMD and MIXER IPs in disp1 power domain have async-bridges (to GSCALER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Configure the pins in external interrupt mode, as done for Snow in
e5e5c6d14e ("ARM: dts: Add power and lid GPIO keys pinctrl for
exynos5250-snow").
Reported-by: Kukjin Kim <kgene@kernel.org>
Suggested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Resolve a merge conflict with mmc refactoring aaa25a5a33 ("ARM: dts:
unuse the slot-node and deprecate the supports-highspeed for dw-mmc in
exynos") by dropping the slot@0 nodes, moving its bus-width property to
the mmc node and replacing supports-highspeed with cap-{mmc,sd}-highspeed,
matching exynos5250-snow.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Currently the Spring DTS has bootargs in the /chosen node and this is
kept since users that don't have a serial console on this board might
be using it to have the boot log shown in the display. This will have
more precedence than the stdout-path but it's fine since is only used
when CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Currently the Snow DTS has a bootargs in the /chosen node and this is
kept since users that don't have a serial console on this board might
be using it to have the boot log shown in the display. This will have
more precedence than the stdout-path but it's fine since is only used
when CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use assigned-clocks/assigned-clock-parents properties for
CMU clock controller DT node to secure proper clock setup:
switching the two muxes to root oscillator clock is not only
required for proper powering down the ISP power domain,
but it also reduces the risk of accessing the ISP CMU
registers while the ISP power domain remains turned off
(i.e. through the common clock framework by clk_summary)
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Armada 380 and 385 SoCs have a Cortex-A9 CPU, so the PMU is available
to be used. This commit enables it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 375 SoC has a Cortex-A9 CPU, and so the PMU is available
to be used. This commit enables it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and XP SoCs have Cortex-A9 compatible CPUs, and with a
Performance Monitoring Unit.
Enable it so that we can have hardware-assisted perf support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Remove the 'ti,timer-dsp' and 'ti,timer-pwm' properties from the timer
nodes that still have them. This seems to be copied from OMAP5, on
which only certain timers are capable of providing PWM functionality
or be able to interrupt the DSP. All the GPTimers On DRA7 are capable
of PWM and interrupting any core (due to the presence of Crossbar).
These properties were used by the driver to add capabilities to each
timer, and support requesting timers by capability. In the DT world,
we expect any users of timers to use phandles to the respective timer,
and use the omap_dm_timer_request_by_node() API. The API to request
using capabilities, omap_dm_timer_request_by_cap() API should be
deprecated eventually.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ti,codec property is not used (parsed) in omap-twl4030 driver. The ti,twl4030-audio
which ti,codec points by phandle is mfd driver and device for ASoC codec is created
w/o DT compatible string. Removing all references in DT files.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The beagle board contains a 16-bit NAND device connected to
chip select 0 of the GPMC controller.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates hdq node compatible property to "ti,am4372-hdq".
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added Pandora 1 GHz model which is based on Classic/Rebirth
with following changes:
- upgraded cpu to dm3730 runs on 1GHz
- 512 MiB DDR-333 SDRAM @ 200 MHz
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added Pandora Rebirth model which is based on Pandora
Classic with 512 MiB DDR-333 SDRAM memory.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This device tree allows to boot, supports the panel,
framebuffer, touch screen, as well as some more peripherals.
Since there is a OMAP3530 based 600 MHz variant and a DM3730 based
1 GHz variant we must include this common device tree code
in one of two CPU specific device trees.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To be able to control the gate for the clkout2 clock output.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds missing dma DTS definitions for omap aes and sham drivers.
Without it kernel drivers do not work for device tree based booting
while it works for legacy booting on general purpose SoCs.
Note that further changes are still needed for high secure SoCs. But since
that never worked in legacy boot mode either, those will be sent separately.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since this is a SOM (System on Module) that will be part
of another embedded board (and can't really exist on its own)
define it as a "dtsi" that will be included in the Device tree
describing the whole system later on.
Hardware specification:
* AM335x SoC
* up to 512 MB RAM
* NAND Flash (8x interface, cs0)
* UART0
* PMIC
* I2C0 (for PMIC)
* 1x Ethernet MAC
Signed-off-by: Rostislav Lisovy <lisovy@jablotron.cz>
[tony@atomide.com: updated nand io size to be just 4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The system timer register range is used to handle three different
functionalities: Periodic Interval Timer, Real Time Timer and watchdog. Declare
it as a syscon to be able to get a regmap.
Also declare it as a simple-mfd and its watchdog subnode.
Finally, document the watchdog compatible string.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
da9210 regulators. Both regulators have their interrupt request lines
tied to the same interrupt pin (IRQ2) on the SoC.
After cold boot or da9063-induced restart, both the da9063 and da9210
seem to assert their interrupt request lines. Hence as soon as one
driver requests this irq, it gets stuck in an interrupt storm, as it
only manages to deassert its own interrupt request line, and the other
driver hasn't installed an interrupt handler yet.
To handle this, install a quirk that masks the interrupts in both the
da9063 and da9210. This quirk has to run after the i2c master driver
has been initialized, but before the i2c slave drivers are initialized.
As it depends on i2c, select I2C if one of the affected platforms is
enabled in the kernel config.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EXNz
-----END PGP SIGNATURE-----
Merge tag 'renesas-da9063-da9210-quirk-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC da9063/da9210 Regulator Quirk for v4.1" from Simon Horman:
The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
da9210 regulators. Both regulators have their interrupt request lines
tied to the same interrupt pin (IRQ2) on the SoC.
After cold boot or da9063-induced restart, both the da9063 and da9210
seem to assert their interrupt request lines. Hence as soon as one
driver requests this irq, it gets stuck in an interrupt storm, as it
only manages to deassert its own interrupt request line, and the other
driver hasn't installed an interrupt handler yet.
To handle this, install a quirk that masks the interrupts in both the
da9063 and da9210. This quirk has to run after the i2c master driver
has been initialized, but before the i2c slave drivers are initialized.
As it depends on i2c, select I2C if one of the affected platforms is
enabled in the kernel config.
* tag 'renesas-da9063-da9210-quirk-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: Add da9063 PMIC device node for system restart
ARM: shmobile: lager dts: Add da9210 regulator interrupt
ARM: shmobile: koelsch: Add da9063 PMIC device node for system restart
ARM: shmobile: koelsch dts: Add da9210 regulator interrupt
ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk
Pull "This pull request contains the following changes from Ray for Cygnus SoCs: from Florian Fainelli:
- enable IOMUX, required for pinmux/pinctrl
- enable GPIO, required for the GPIO driver
- enable GPIO hook detection for BCM911360-based phone designs
- enable PCIe controller for the bcm958300k designs
* tag 'arm-soc/for-4.1/devicetree-part-2' of http://github.com/broadcom/stblinux:
ARM: dts: enable PCIe support for Cygnus
ARM: dts: cygnus: enable GPIO based hook detection
ARM: dts: enable GPIO for Broadcom Cygnus
ARM: dts: enable IOMUX for Broadcom Cygnus
This patch introduces devicetree for the Alpine platform, and
for a development board based on the same platform.
Signed-off-by: Barak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
update to the MAINTAINERS entry adding a rockchip regexp entry.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVBIBSAAoJEPOmecmc0R2BitkH/2zUwSyOh/zTpyxS3XqzfNJa
88AKTy1FVMIfI9aaL3HjVYe9/NwcQUYj3Av/0GnwqXRsV8mCbGY0s1ou1a+Xe6qw
YR6rDBAzjKcvYk8zsPVE91L29nA81VMxbgEVLtGQmeBUzbAX4Ac9poWo9xLzSHaG
UTxA18VArMmmHn47KgOPz1S2qTQikVjpDyfPF7fU/bn6aLPLrtzHd0Bq1RI5uG8q
3rA4ZVEb18bK3DIBIH+vf1v6GTF33VZrCtTWqI5RFV9OO+0nglNfERHGx9z7gi7x
vXXze1kKnaL+nsjxjhQg/oRhN+4YlivoEt1Z2Is4v2/2sYXP6T/C7bbOVdQZQoY=
=VQ49
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "ARM: rockchip: small fixes for 4.0-rc" from Heiko Stuebner:
Adding a default-disabled state to the new gmac node and an
update to the MAINTAINERS entry adding a rockchip regexp entry.
* tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
OMAP4/5 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the WUGEN HW block, kernels with this patch applied
won't have any suspend-resume facility when booted with old DTs,
and old kernels with updated DTs won't even boot.
On a platform with this patch applied, the system looks like
this:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 0 0 WUGEN 37 gp_timer
19: 233799 155916 GIC 27 arch_timer
23: 0 0 WUGEN 9 l3-dbg-irq
24: 1 0 WUGEN 10 l3-app-irq
27: 282 0 WUGEN 13 omap-dma-engine
44: 0 0 4ae10000.gpio 13 DMA
294: 0 0 WUGEN 20 gpmc
297: 506 0 WUGEN 56 48070000.i2c
298: 0 0 WUGEN 57 48072000.i2c
299: 0 0 WUGEN 61 48060000.i2c
300: 0 0 WUGEN 62 4807a000.i2c
301: 8 0 WUGEN 60 4807c000.i2c
308: 2439 0 WUGEN 74 OMAP UART2
312: 362 0 WUGEN 83 mmc2
313: 502 0 WUGEN 86 mmc0
314: 13 0 WUGEN 94 mmc1
350: 0 0 PRCM pinctrl, pinctrl
406: 35155709 0 GIC 109 ehci_hcd:usb1
407: 0 0 WUGEN 7 palmas
409: 0 0 WUGEN 119 twl6040
410: 0 0 twl6040 5 twl6040_irq_ready
411: 0 0 twl6040 0 twl6040_irq_th
IPI0: 0 1 CPU wakeup interrupts
IPI1: 0 0 Timer broadcast interrupts
IPI2: 95334 902334 Rescheduling interrupts
IPI3: 0 0 Function call interrupts
IPI4: 479 648 Single function call interrupts
IPI5: 0 0 CPU stop interrupts
IPI6: 0 0 IRQ work interrupts
IPI7: 0 0 completion interrupts
Err: 0
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This block should not be enabled by default or else if the kconfig is set,
it will try to load/probe even if there's no phy connected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The DBGU is not a simple UART and we need to be able to distinguish it from the
other UARTs, in particular to get its address and check the chip id.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds the static vcc_sys regulator to the rk3288-evb, the missing
rk808 supplies from it and all the supplies of the act8846 evb-variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVAFaGAAoJEAf03oE53VmQilsH/Aie6f2WmzqtBACUTJKae3Kj
BLXyewX89rSEDuUEjImJhYdafYDEq/5IeoeRMY/qPdXKrY0KCEhwnVUT5LEH3qy3
P8yl0UAtZycMnKtP2YhFRAFUY/DozxprcOqTw4IfZ7PHHsQKcn4+qrgG8LcHpvfZ
d5wv6C+6gi9UBh3B7omOx98ULFDOnST56UhOml9HGsdOgCc7AbsusEG4FzRON7Bc
4QEJuYxxZPONoeuczpn9qF8SFk9ShO5dHQsjzWkSZjgneBPJK7vujcItR9KWWqw5
gtjQ19BPNuAYY4MY6/2mc/qOGsA3o17Cn9CvNwaAnlvMLebk4tMAWL8Y9Dmjouc=
=l68g
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes3' into at91-4.1-cleanup
Third fixes batch for AT91 on 4.0:
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+DZAAAoJEAf03oE53VmQe34H/3cACqt00PvJiJ/DJNOLq8xM
1E93vZb/sQ5nD4JwF1DK1/VezT8QjOpIdb/Uo/XIKxqV0T7ZfFcLcAYHDCZup1HP
VbNtGRYPDGtQypBBVHDgCHwfgH6QVjTQJk67vjZkKmvWXFBnv6akY2XTrXLeMBKw
24nWEamrpR5tlEG5z9WIx6YFYBslDHq+R8j98AThJRo3NI+d00FPYwfDEwNf730e
T4xh/Rzz9eNbttBoTP5AeN75OXowsnpZwVicbQNtkX0E2jNdv1Ltbkpzc9zWdw8m
pL1kf+sV2MvD7KvcOrFGXMD2Ei3MCUNFdscaftQvfjutjEdmF2eIcK4qAzYRifw=
=UTAc
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' into at91-4.1-cleanup
Second fixes batch for AT91 on 4.0:
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU9uKaAAoJEAf03oE53VmQrT4IAID5RZZLycH65MfI2SWs5jHJ
riXpp2ByX2YMZhBV7Y+jSJcdty0zdZFXAm3cME8YtHSHFNW87y3U90BhL1JTwFh8
Rlk45xxauRmiH5R+0haBIavt+ZFHB8QOgmAE+xa4Vc/qBiry6HSgWVldk3yiai5j
Mnq/+UpeL7mSlcn9kFkbVVOkDiP2tRoITU0z780tBgywbUQEluNZan4MfjSaknzP
GEwmN74Z6QPUxhqc1Z1ACU84ozYcLYaiMksNXrTch0+dLz91MIRl6Eqb53XhJEK3
P8ysCj16UBgX2JuuYWBGkxrZ1Brl0Lj5075JrM+He0T/XRsLTChb+9rQ14QrKno=
=YpBm
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' into at91-4.1-cleanup
First fixes batch for AT91 on 4.0:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9S+0ACgkQCwYYjhRyO9XSkQCfcrsiF6bS+B1B9Gdu+nBwyXdC
BHYAmwUm92D7yH8ePjbKldM4ONM1315b
=yn/6
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
ARM: mvebu: fix unit address of MPIC nodes
ARM: mvebu: use stdout-path in all armada-*.dts
ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
ARM: mvebu: add UART labels to Armada 375
ARM: mvebu: add missing UART labels on Armada 38x
ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
ARM: mvebu: a385-db-ap: Enable the NAND
ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
ARM: mvebu: Fix MPIC unit address
ARM: dts: dove: Add some more common pinctrl settings
ARM: dts: dove: Add node labels for PCIe ports 0 and 1
ARM: dts: dove: Always include gpio and interrupt-controller headers
ARM: dts: dove: Fix uart[23] reg property
ARM: mvebu: add Linksys WRT1900AC (Mamba) support
ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
ARM: mvebu: Update the SDHCI node on Armada 38x
ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node
Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:
This pull request contains the following Broadcom SoCs Device Tree changes:
- Jonathan adds support for the Broadcom Cygnus BCM958305K board
- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
on Netgear R6250
* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
ARM: BCM5301X: Add DT for Netgear R8000
ARM: dts: Enable Broadcom Cygnus BCM958305K
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVAFaGAAoJEAf03oE53VmQilsH/Aie6f2WmzqtBACUTJKae3Kj
BLXyewX89rSEDuUEjImJhYdafYDEq/5IeoeRMY/qPdXKrY0KCEhwnVUT5LEH3qy3
P8yl0UAtZycMnKtP2YhFRAFUY/DozxprcOqTw4IfZ7PHHsQKcn4+qrgG8LcHpvfZ
d5wv6C+6gi9UBh3B7omOx98ULFDOnST56UhOml9HGsdOgCc7AbsusEG4FzRON7Bc
4QEJuYxxZPONoeuczpn9qF8SFk9ShO5dHQsjzWkSZjgneBPJK7vujcItR9KWWqw5
gtjQ19BPNuAYY4MY6/2mc/qOGsA3o17Cn9CvNwaAnlvMLebk4tMAWL8Y9Dmjouc=
=l68g
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Third fixes batch for AT91 on 4.0" from Nicolas Ferre:
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
* tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
This patch adds the DT description for the LaCie "2Big NAS" (nas2big).
This NAS is an hardware upgrade of the 2Big Network v2.
Chipset and device list:
- CPU Marvell 88F6282 1600Mhz
- SDRAM memory, 256MB DDR3 (2x128MB x8) 533Mhz
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- Flash memory, NAND 256MB TSOP48
- I2C EEPROM, 512 bytes (AT24 type)
- PCIe SATA controller JMicron JMB360 (eSATA)
- I2C fan controller GMT G762 (with a separate alarm GPIO)
- 1 USB2 host port
- 1 push button
- 1 power switch
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
- CPLD for LEDs and start-up management (Altera Max EMP3064)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18
The at91rm9200, at91sam9260, at91sam9261 and at91sam9263 SoCs have slightly
different UDC IPs.
Those differences were previously handled with cpu_is_at91xx macro which
are about to be dropped for multi-platform support, thus we need to
change compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
There is no specific driver handling the AHB matrix, this is a simple syscon
device. the matrix is needed by several other drivers including the USB on some
SoCs (at91sam9261 for instance).
Without this definition, the USB will not work on these SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/8l7AAoJEFBXWFqHsHzOb3sH/1fFkQXzUcAon971XnD3sP55
zAbUvcowEQ/04xpb3Q5r5KCfeN4UvOCSY6Zed4sevq/TJZidYl8DKu9q4s0rSnfX
m1GghT3pAixMlyEWdJldmIwTYBXEkaJVrqeNuTB6BqBIsInWW/R+WkuByrPGkaxS
P5ENbyMVz68S0Cq88lmYzFjRXCCc2vWPZiVKj0DEOnqld1TIpY9hQyZwHmepCydZ
GKHLApyWP9qyUs/N6Bxwt/2vPoauit2xfDTvCbBk75jO34uSYEo9L9YpwDQorXPW
f6vj1EkVqW3TljghEm/kSoi1nhU2fNnfUAWClfKQ1UO2yzNLQAWtY+23upR5Qkw=
=kuEJ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.0" from Shawn Guo:
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
* tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C0ct
-----END PGP SIGNATURE-----
Merge tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes against v4.0-rc2" from Tony Lindgren:
Fixes for various omap variants, mostly minor fixes for various SoCs
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
* tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
ARM: dts: am335x-lxm: Use rmii-clock-ext
ARM: dts: am335x-bone-common: enable aes and sham
ARM: dts: am43xx-clocks: Fix ehrpwm tbclk data on am43xx
ARM: dts: am33xx-clocks: Fix ehrpwm tbclk data on am33xx
ARM: dts: OMAP5: Fix the bypass clock source for dpll_iva and others
ARM: dts: DRA7x: Fix the bypass clock source for dpll_iva and others
ARM: OMAP4+: PRM: fix omap4 version of prm_save_and_clear_irqen
ARM: OMAP2+: hwmod: fix deassert hardreset clkdm usecounting
ARM: DRA7: hwmod_data: Fix hwmod data for pcie
ARM: omap2+: omap_hwmod: Set unique lock_class_key per hwmod
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+DZAAAoJEAf03oE53VmQe34H/3cACqt00PvJiJ/DJNOLq8xM
1E93vZb/sQ5nD4JwF1DK1/VezT8QjOpIdb/Uo/XIKxqV0T7ZfFcLcAYHDCZup1HP
VbNtGRYPDGtQypBBVHDgCHwfgH6QVjTQJk67vjZkKmvWXFBnv6akY2XTrXLeMBKw
24nWEamrpR5tlEG5z9WIx6YFYBslDHq+R8j98AThJRo3NI+d00FPYwfDEwNf730e
T4xh/Rzz9eNbttBoTP5AeN75OXowsnpZwVicbQNtkX0E2jNdv1Ltbkpzc9zWdw8m
pL1kf+sV2MvD7KvcOrFGXMD2Ei3MCUNFdscaftQvfjutjEdmF2eIcK4qAzYRifw=
=UTAc
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Second fixes batch for AT91 on 4.0" from Nicolas Ferre:
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/pm: MOR register KEY was missing
ARM: at91/dt: sama5d4: fix lcdck clock definition
ARM: at91/dt: sama5d4: rename lcd_clk into lcdc_clk
ARM: at91: debug: fix non MMU debug
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pm9Y
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next into fixes
Pull "Fixes for v4.0 on the SoCFPGA platform" from Dinh Nguyen:
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
* tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: make sure socfpga_cpu1start_addr is properly flushed
ARM: socfpga: fix uart DMA binding error
ARM: socfpga: Correct SCU virtual mapping in socfpga
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables all 3 GPIO controllers including the ASIU GPIO, the
chipcommonG GPIO, and the ALWAYS-ON GPIO, for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the IOMUX support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).
Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some at91 SoCs embed a 10/100 Mbit Ethernet IP, that is based on the
at91sam9260 SoC.
Fix at91 DTs accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Radxa Rock board most supplies come from the static 5v vsys supply, but
the inl1-supply comes from the REG4 of the act8846 itself. Model this dependency
using the added supply-handling to make sure the supplying regulator gets handled
correctly and not accidentially turned off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The switches on r8a73a4/ape6evm do not have pull-up registers. The
schematics say: "Need to use APE6 internal PullUp", hence enable pull-up
using pinctrl.
Without this, the switches don't really work, as the GPIO inputs are
more likely to pick up ghost signals through capacitive coupling than
actual keypresses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1m2R
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.1" from Simon Horman:
* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC
* tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: r8a7794: add SDHI DT support
ARM: shmobile: r8a7790: add ADSP clocks
ARM: shmobile: r8a7791: add ADSP clocks
ARM: shmobile: henninger: add CAN0 DT support
ARM: shmobile: r8a7791: add CAN DT support
ARM: shmobile: r8a7791: add CAN clocks
ARM: shmobile: r8a7790: add CAN DT support
ARM: shmobile: r8a7790: add CAN clocks
ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
ARM: shmobile: emev2 dtsi: Add PFC information
ARM: shmobile: r8a7791: smp: remap whole apmu region
ARM: shmobile: r8a7790: smp: remap whole apmu region
ARM: shmobile: koelsch: Add DU HDMI output support
ARM: shmobile: r8a7791: Correct SDHI clock labels and output-names
ARM: shmobile: r8a7794: Correct SDHI clock base address, labels and output-names
ARM: shmobile: r8a7794: alt: Enable ethernet controller
ARM: shmobile: r8a7794: Add ethernet controller to device tree
ARM: shmobile: r8a7794: Add IPMMU DT nodes
ARM: shmobile: r8a7791: Add IPMMU DT nodes
ARM: shmobile: r8a7790: Add IPMMU DT nodes
...
* Remove the sh7372 SoC and its mackerel board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lpw8
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Pull "Renesas ARM Based SoC sh7372 SoC Removal Updates for v4.1" from Simon Horman:
* Remove the sh7372 SoC and its mackerel board
* tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
Documentation: Remove ZBOOT MMC/SDHI utility and docs
ARM: shmobile: sh7372 dtsi: Remove Legacy DTSI file
ARM: shmobile: sh7372: Remove DT binding documentation
ARM: shmobile: sh7372: Remove Legacy C SoC code
ARM: shmobile: sh7372: Remove ZBOOT MMC/SDHI support
ARM: shmobile: mackerel: Remove from MAINTAINERS
ARM: shmobile: mackerel: Remove defconfig
ARM: shmobile: mackerel: Remove mach-type entry
ARM: shmobile: mackerel: Remove DT binding documentation
ARM: shmobile: mackerel dts: Remove Legacy DTS file
ARM: shmobile: mackerel: Remove Legacy C board code
ARM: shmobile: mackerel: Remove ZBOOT code
[arnd: The sh7372 platform is rather dated and is believed to
have no active users on modern kernels. It stands in the way
of converting all of mach-shmobile to be multiplatform capable,
as adding pinctrl and common-clock support for it would be more
work than it's worth. As always, should any legitimate upstream
users show up in the future, we will revert this removal]
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU9uKaAAoJEAf03oE53VmQrT4IAID5RZZLycH65MfI2SWs5jHJ
riXpp2ByX2YMZhBV7Y+jSJcdty0zdZFXAm3cME8YtHSHFNW87y3U90BhL1JTwFh8
Rlk45xxauRmiH5R+0haBIavt+ZFHB8QOgmAE+xa4Vc/qBiry6HSgWVldk3yiai5j
Mnq/+UpeL7mSlcn9kFkbVVOkDiP2tRoITU0z780tBgywbUQEluNZan4MfjSaknzP
GEwmN74Z6QPUxhqc1Z1ACU84ozYcLYaiMksNXrTch0+dLz91MIRl6Eqb53XhJEK3
P8ysCj16UBgX2JuuYWBGkxrZ1Brl0Lj5075JrM+He0T/XRsLTChb+9rQ14QrKno=
=YpBm
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "First fixes batch for AT91 on 4.0" from Nicolas Ferre:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: keep watchdog running in idle mode
dts: Documentation: AT91 Watchdog, explain what atmel,idle-halt property really do
ARM: at91/defconfig: add at91rm9200 ethernet support
ARM: at91/defconfig: remove CONFIG_SYSFS_DEPRECATED
ARM: at91/dt: at91sam9260: fix usart pinctrl
ARM: at91/dt: sama5d4: add missing alias for i2c0
ARM: at91/dt: at91sam9263: Fixup sram1 device tree node
ARM: at91: pm: fix SRAM allocation
ARM: at91: pm: fix at91rm9200 standby
pm: at91: Workaround DDRSDRC self-refresh bug with LPDDR1 memories.
pm: at91: pm_slowclock: fix suspend/resume hang up in timeouts
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gbWq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung tmu and hdmi regression fixes for v4.0" from Kukjin Kim:
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
* tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add display power domain for exynos5250
ARM: dts: add 'hdmi' clock to mixer nodes for exynos5250 and exynos5420
ARM: dts: enable hdmi support for exynos4210-universal_c210
ARM: dts: enable hdmi support for exynos4412-odroid-common
ARM: dts: add dependency between TV and LCD0 power domains for exynos4
ARM: dts: add hdmi related nodes for exynos4 SoCs
ARM: EXYNOS: add support for sub-power domains
dt-bindings: document a note about power domain subdomains
ARM: dts: Provide dt bindings identical for Exynos TMU
ARM: dts: Trip points and sensor configuration data for exynos5440
ARM: dts: define default thermal-zones for exynos4
ARM: dts: default trip points definition for exynos5420
ARM: dts: add TMU default definitions for exynos4412
ARM: dts: Adding CPU cooling binding for Exynos SoCs
ARM: dts: Enable TMU for exynos4412-odriod-common
ARM: dts: Add LDO10 for TMU for exynos4412-odroid-common
ARM: dts: Enable TMU for exynos4210-trats
PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).
This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
socfpga.dtsi is missing the DMA channels for the uart nodes.
This will produce the following errors:
of_dma_request_slave_channel: dma-names property of node '/soc/serial0@ffc02000' missing or empty
ttyS0 - failed to request DMA
Provide the correct DMA channels to fix this.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: Philip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add a new file: at91sam9x5_isi.dtsi, which includes ISI node and
pinctrls.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.
Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.
So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC, L2 cache
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
controller, MPIC interrupt controller, timer, CPU reset for SMP,
PMSU.
* I2C
* SPI
* SDHCI
* XOR
* NAND
* UART
* PCIe
Additional features will be supported in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Device Tree nodes describing the MPIC nodes on Armada 370, 375,
38x and XP had a unit address that did not match the first reg
property, as suggested by the ePAPR. This commit fixes that.
[gregory.clement@free-electrons.com: removed the armada-38x part, as it
was already applied by a previous patch]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the stdout-path property in /chosen for all Armada
boards that were not yet carrying this property, and gets rid of
/chosen/bootargs which becomes unneeded: earlyprintk should not be
used by default, and the console= parameter is replaced by the
/chosen/stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds 'serialX' aliases for the various serial ports on
Armada 370, 375, 38x and XP platforms. It will allow the usage of the
stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Having aliases for Ethernet devices is useless, since the networking
subsystem unfortunately doesn't care about aliases to name network
interfaces.
Note that the 'aliases' nodes in armada-370-xp.dtsi and armada-xp.dtsi
become empty, but that we keep it as is since a followup patch will
re-add some aliases to it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the standard uart0 and uart1 DT labels to the Device
Tree description of the Marvell Armada 375 SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 38x had a label for UART0, but not UART1. This commit fixes
that.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Marvell Armada 38x, the USB2 controller registers are at 0x58000,
so the corresponding Device Tree node should have a unit address of
58000, and not 50000. We were using 50000 due to an incorrect
copy/pastebin of Armada 370/XP code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 385 Access Point Development Board has a 1GB NAND SLC chip from
Micron as its main storage. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a DSA section to the DT blob representing the Ethernet switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the LaCie 2Big Network v2 (net2big_v2) board, the fan alarm is not
wired to the I2C fan controller but to a separe GPIO. This GPIO can be
controlled by using the gpio-fan driver.
This patch adds the gpio-fan alarm description in the net2big_v2 DTS.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The unit-address is supposed to be equal the first reg address, which is not
the case for the MPIC, that uses the mbus-controller one. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This add common pinctrl settings for pcie[01]_clkreq, spi1, i2c[23],
and internal i2c mux. These settings have either one or two options
only, so put them into the SoC dtsi instead of repeating them on
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since turning on idle-halt in commit fe46aa679f (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DT file to enable the Wireless Audio reference design based on the
BCM58305.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a DTS file for MINIX NEO-X8, a Meson8-based digital media player.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Add pinctrl node to the DTSI file for meson8 and sub-nodes for some
standard mux configurations.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Add a node for the Ethernet controller to Meson DTS file and
enable it on the Geniatech ATV1200 board.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
This adds a node for the SPI Flash Controller to the Amlogic Meson
DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Mark Brown <broonie@kernel.org>
The PHY IRQ line is connected to external IRQ8, not IRQ0. Fix DT
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds sound card using the ak4643 codec.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds an entry for an R-Car Gen. 1 sound controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[horms: Removed undocumented "renesas,rcar_sound" compat string]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 65MHz pixel clock connected to the DU clock input.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While the LEDs on r8a73a4/ape6evm are tied to VSUPPLY, they're driven by
an N-channel MOSFET. Hence the GPIO signal should be active high.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sets the extal clock to the frequency of the oscillator installed by
default (33 MHz).
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node to the new BSC node, as its connected to the
Bus State Controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: dropped compat string changes as they seem out of scope]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Peach Pit and Pi boards, the Exynos SoC XCLKOUT pin provides
master clock (mclk) to the codec. So make it a clock consumer.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Peach Pit and Pi boards have a WiFi module that is always powered
but needs toggling an enable pin and ungating a 32kHz reference
clock as part of their power sequencing.
Add a dev node for the SDIO slot and a MMC power sequence provider.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The patch adds domain definition and references to it in appropriate devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
[mszyprow: rebased onto generic power domains dt bindings]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Mixed block needs to control hdmi clock to properly perform power on/off
operation, so add 'hdmi' clock also to mixer nodes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds configuration of hw modules required to enable HDMI
support on Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
TV Mixer needs both TV and LCD0 domains enabled to be fully operational.
This dependency is modelled by making TV power domains a sub-domain of
LCD0 power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds entries for HDMI, Mixer and i2c with hdmi-phy modules
found in Exynos 4210 and 4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented device tree bindings provide data already hardcoded in the
exynos_tmu_data.c file.
After this commit, it should be possible to reuse common thermal core
framework in Exynos SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit provides information about Exynos5440 device configuration.
Previously this information was available in exynos_tmu_data.c file.
Now it is available in the device tree.
Such approach allows reusing some common code for thermal.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Trip points corresponding to the one defined in the exynos_tmu_data.c
for Exynos4 have been included.
This thermal-zones attribute is afterwards reused for Exynos4210,
Exynos4412 and Exynos5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This code groups in one place default settings of trip points.
It is used in SoCs with multiple instances of TMU sensor.
Separate device tree file prevents from multiple copying of the
same data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos 4 and 5 family of SoCs uses almost identical TMU sensor to
measure the on chip temperature. For this reason it is possible to
group TMU configuration parameters in one dts file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented patch aims to move data necessary for correct CPU cooling device
configuration from exynos_tmu_data.c to device tree.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit enables TMU IP block on the Exynos4412 Odroid based
devices such as Odroid U3.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The thermal IP block (Thermal Management Unit) called TMU has been
enabled in this device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add pcie[01] node labels to allow to reference them easily from
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We want to enforce the use of named flags in GPIO and interrupt
specifiers, include the corresponding headers to Dove's SoC dtsi.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix Dove's register addresses of uart2 and uart3 nodes that seem to
be broken since ages due to a copy-and-paste error.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900AC (Mamba) is a router that has
- 2 mini-PCIe slots with Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 256MB RAM
gregory.clement@free-electrons.com: - add ARM to the title
- fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE
- fix the unbalanced comment for the syscfg partition
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
