commit e5e21f70bf ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().
However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.
Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.
Fixes: e5e21f70bf ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the context with *rdev available, regulator core provides
rdev_get_id()/rdev_get_regmap() APIs to get regulator id and *regmap.
So no need to store them in struct stpmic1_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no vsel_reg/vsel_mask settings for PV88060_ID_SWx, so don't use
pv88060_ldo_ops for PV88060_SW. The PV88060_ID_SWx is fixed voltage,
set .fixed_uV instead of .min_uV then regulator core will automatically
support get_voltage and list_voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a remnant of commit 70a7fb80e8 ("regulator: core: Fix nested
locking of supplies").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.
Found by debugging a broken voltage setup on Orange Pi One Plus.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is for LTC3676 rather than LTC1376.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use case range for continuous range to make the code shorter.
The .readable_reg and .writable_reg implementation are exactly the same,
so use a common ltc3676_readable_writeable_reg function instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
read ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator_desc_list_voltage_linear_range which can be used
by drivers for getting the voltages before regulator is registered.
This may be useful for drivers which need to fetch the voltage
selectors at device-tree parsing callback.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a result of exporting the bd70528 specific locking functions
we no longer need struct bd70528. Remove references to
struct bd70528 from bd70528 regulator.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step values for some of the LDOs appears to be incorrect, resulting
in incorrect voltages (or at least, ones which are different from the
Samsung 3.4 vendor kernel).
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There are several lines in an if statement that are not indented
correctly. Fix these by removing the tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
linear range is suitable for this driver, let's convert it to linear range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in error path.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device links are refcounted, device_link_remove() has to be called as
many times as device_link_add().
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With current n_voltages setting, regulator_list_voltage will return
-EINVAL when selector >=57. The highest selector is 0x41, so the
n_voltages should be 0x41+1, i.e. 66.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we changed all providers to pass descriptors into the core
for enable GPIOs instead of a global GPIO number, delete the support
for passing GPIO numbers in, and we get a cleanup and size reduction
in the core, and from a GPIO point of view we use the modern, cleaner
interface.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_* managed device resources and create a local
struct device *dev variable to simplify the code inside
probe().
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This pushes the handling of inversion semantics and open drain
settings to the GPIO descriptor and gpiolib. All affected board
files are also augmented.
This is especially nice since we don't have to have any
confusing flags passed around to the left and right littering
the fixed and GPIO regulator drivers and the regulator core.
It is all just very straight-forward: the core asks the GPIO
line to be asserted or deasserted and gpiolib deals with the
rest depending on how the platform is configured: if the line
is active low, it deals with that, if the line is open drain,
it deals with that too.
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> #OMAP1 Amstrad Delta
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the GPIO regulator driver to use decriptors only.
We have to let go of the array gpio handling: the fetched descriptors
are handled individually anyway, and the array retrieveal function
does not make it possible to retrieve each GPIO descriptor with
unique flags. Instead get them one by one.
We request the "enable" GPIO separately as before, and make sure
that this line is requested as nonexclusive since enable lines can
be shared and the regulator core expects this.
Most users of the GPIO regulator are using device tree.
There are two boards in the kernel using the gpio regulator from a
non-devicetree path: PXA hx4700 and magician. Make sure to switch
these over to use descriptors as well.
Cc: Philipp Zabel <p.zabel@pengutronix.de> # Magician
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Kevin Hilman <khilman@baylibre.com> # Meson
Cc: Neil Armstrong <narmstrong@baylibre.com> # Meson
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It looks like linear range is suitable to describe the voltage table
for rk805 buck1/2:
selector 0 ~ 59: 0.7125V with uV_step = 12500
selector 60 ~ 62: 1.8V with uV_step = 200000
selector 63: 2.3V
With this change, then rk805 buck1/2 can reuse rk808_reg_ops_ranges.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
A comma has been accidentally used where a semi-colon was clearly
intended, correct this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK805 has the following voltage range for the BUCK1 and BUCK2 regulators:
From 0.7125V to 1.45V in 12.5mV steps, 1.8V, 2V, 2.2V and 2.3V
, which corresponds to the following values as per the RK805
datasheet:
000 000: 0.7125V
000 001: 0.725V
……
111 011: 1.45V
111 100: 1.8V
111 101: 2.0V
111 110: 2.2V
111 111: 2.3V
This means that the voltage range is not linear and so RK805 can not
reuse the same regulator_ops structure from RK808.
Fix it by creating a list with the correct supported voltage values
for RK805 BUCK1 and BUCK2 regulators.
Tested on a rv1108-elgin-r1 board that now correctly reports a BUCK2
voltage of 2.2V instead of the unsupported value of 1.4875V.
Fixes: c4e0d344c1 ("regulator: rk808: Add regulator driver for RK805")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure unwind all resources if probe fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a platform driver, no need to include linux/i2c.h.
Include linux/of.h for of_match_ptr.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support for max77650. We support all four variants of this
PMIC including non-linear voltage table for max77651 SBB1 rail.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix copy-paste mistake while converting to use defines for masks.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using devm_regulator_register, so it's not necessary to
store *rdev[3] in struct isl_pmic. Use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While at it, also fix indent for rk805_reg_ops and rk805_switch_ops.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below build error:
drivers/regulator/mcp16502.c: In function ‘mcp16502_gpio_set_mode’:
drivers/regulator/mcp16502.c:135:3: error: implicit declaration of function ‘gpiod_set_value’; did you mean ‘gpio_set_value’? [-Werror=implicit-function-declaration]
gpiod_set_value(mcp->lpm, 0);
^~~~~~~~~~~~~~~
gpio_set_value
drivers/regulator/mcp16502.c: In function ‘mcp16502_probe’:
drivers/regulator/mcp16502.c:486:13: error: implicit declaration of function ‘devm_gpiod_get’; did you mean ‘devm_gpio_free’? [-Werror=implicit-function-declaration]
mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
^~~~~~~~~~~~~~
devm_gpio_free
drivers/regulator/mcp16502.c:486:40: error: ‘GPIOD_OUT_LOW’ undeclared (first use in this function); did you mean ‘GPIOF_INIT_LOW’?
mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
^~~~~~~~~~~~~
GPIOF_INIT_LOW
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since devm_regmap_field_alloc can fail, add error checking for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since devm_regmap_field_alloc can fail, add error checking for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since c32569e358 ("regulator: Use of_node_name_eq for node name
comparisons"), regulator node name comparisons are case sensitive.
The DA9052 driver uses uppercase, but the DT has lowercase.
Fix this by using a lowercase regulator name to match the DT node name.
Fixes: c32569e358 ("regulator: Use of_node_name_eq for node name comparisons")
Cc: Support Opensource <support.opensource@diasemi.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since c32569e358 ("regulator: Use of_node_name_eq for node name
comparisons") Vivien reported the mc13892-regulator complaining about
not being able to find regulators.
This is because prior to that commit we used of_node_cmp() to compare
the regulator array passed from mc13892_regulators down to
mc13xxx_parse_regulators_dt() and they are all defined in uppercase
letters by the MC13892_*_DEFINE* macros, whereas they are defined as
lowercase in the DTS.
Fix this by using a lowercase regulator name to match the DT node name.
Fixes: c32569e358 ("regulator: Use of_node_name_eq for node name comparisons")
Reported-by: Vivien Didelot <vivien.didelot@gmail.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_linear_range arrays and stpmic1_regulator_cfgs are only
accessed by this driver and the values are never changed so make them
static const. regulator_ops variables can also be const.
Also clean up a few empty lines in regulator_linear_range array.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD70528MWV is an ultra-low Iq general purpose single-chip power
management IC for battery-powered portable devices.
Add support for controlling 3 bucks and 3 LDOs present in
ROHM BD70528.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some scenarios the early stages of the boot chain has configured
regulators to be in a required state, but the later stages has skipped
to inform the RPM about it's requirements.
But as the SMD RPM regulators are being initialized voltage change
requests will be issued to align the voltage with the valid ranges. The
RPM aggregates all parameters for the specific regulator, the voltage
will be adjusted and the "enabled" state will be "off" - and the
regulator is turned off.
This patch addresses this problem by caching the requested enable state,
voltage and load and send the parameters in a batch, depending on the
enable state - effectively delaying the voltage request for disabled
regulators.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing MODULE_DEVICE_TABLE and remove the comma from the
separator on the end of the of_device_id array.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf
Fixes: df3a950e4e ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having instance specific copy of desc is enough to support multiple
instance of pwm regulator.
The regulator_ops is never changed so no need to copy it per instance, make
pwm_regulator_voltage_table_ops and pwm_regulator_voltage_continuous_ops
const to ensure they won't be changed.
The pwm_regulator_desc is a template to be copied so also make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If regulator DT node doesn't exist, its of_parse_cb callback
function isn't called. Then all values for DT properties are
filled with zero. This leads to wrong register update for
FPS and POK settings.
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Provide a helper allowing to access regulator's regmap.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, hence there is a potential null pointer dereference on rdev.
Fix this by null checking rdev first.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix few trivial language typos in core and drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev_get_id() instead of directly access rdev->desc->id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current implementation missed the case BCM590XX_REG_VSR, so
bcm590xx_get_enable_register() returns 0 when id is BCM590XX_REG_VSR.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix trival copy-n-paste mistake.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so,
returns with its error code.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build error when CONFIG_REGMAP_I2C=m && CONFIG_REGULATOR_MCP16502=y.
drivers/regulator/mcp16502.o: In function `mcp16502_probe':
mcp16502.c:(.text+0xca): undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mcp16502_suspend/resume_noirq is only used by SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
when CONFIG_PM_SLEEP is defined.
So use #ifdef CONFIG_PM_SLEEP instead CONFIG_SUSPEND guard.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does the following:
- align parameter with parenthesis
- fix compile error
If CONFIG_SUSPEND is not set the dummy pm_ops
callbacks are named mcp16502_suspend and mcp16502_resume
instead of mcp16502_suspend_noirq and mcp16502_resume_noirq.
Excerpt from compile log (kbuild test robot):
In file included from include/linux/device.h:23:0,
from include/linux/gpio/driver.h:5,
from include/asm-generic/gpio.h:13,
from include/linux/gpio.h:62,
from drivers/regulator/mcp16502.c:11:
>> drivers/regulator/mcp16502.c:527:32: error: 'mcp16502_suspend_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend'?
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
>> drivers/regulator/mcp16502.c:528:10: error: 'mcp16502_resume_noirq'
undeclared here (not in a function); did you mean 'mcp16502_suspend_noirq'?
mcp16502_resume_noirq)
vim +527 drivers/regulator/mcp16502.c
524
525 #ifdef CONFIG_PM
526 static const struct dev_pm_ops mcp16502_pm_ops = {
> 527 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq,
> 528 mcp16502_resume_noirq)
529 };
530 #endif
531 static const struct i2c_device_id mcp16502_i2c_id[] = {
532 { "mcp16502", 0 },
533 { }
534 };
535 MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id);
536
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
drivers/regulator/act8945a-regulator.c:340:1: warning:
symbol 'act8945a_pm' was not declared. Should it be static?
Fixes: 7482d6ecc6 ("regulator: act8945a-regulator: Implement PM functionalities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix 'defined but not used' compiler warning for act8945a_suspend()
function in case CONFIG_PM_SLEEP is not defined.
Fixes: b5ebba46e6 ("regulator: act8945a-regulator: add shutdown function")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reported-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of set_ramp_delay feature was missing an assignment which
should have populated slew_rate table for dcdc2 regulator. Add it.
Fixes: d29f54df8b ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for entering/resuming suspend states.
It does this by setting the LPM pin of the PMIC.
When suspending the PMIC will enter the Low-power mode
when the LPM pin will be set to high. If the suspend target state
is suspend-to-mem, the PMIC will transition to Hibernate mode,
otherwise, if it is standby, it will remain in Low-power mode.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement shutdown method to make sure the PMIC will not enter the suspend
state when the system is shutdown.
This work is based on work done by Borris Brezillon on [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix line over 80 chars checkpatch.pl warning.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
fix checkpatch warning, adapt commit message, add LDO modes support,
move modes constants to active-semi,8945a-regulator.h, remove rdevs from
struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlock expert registers for act8945a.
This is based on orginal work of Boris Brezillon at [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the Arizona LDO1 driver becomes
redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the wm8994 driver becomes redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of regulator_resolve_supply() we have historically turned
on our supply in some cases. This could be for one of two reasons:
1. If resolving supplies was happening before the call to
set_machine_constraints() we needed to predict if
set_machine_constraints() was going to turn the regulator on and we
needed to preemptively turn the supply on.
2. Maybe set_machine_constraints() happened before we could resolve
supplies (because we failed the first time to resolve) and thus we
might need to propagate an enable that already happened up to our
supply.
Historically regulator_resolve_supply() used _regulator_is_enabled()
to decide whether to turn on the supply.
Let's change things a little bit. Specifically:
1. Let's try to enable the supply and the regulator in the same place,
both in set_machine_constraints(). This means that we have exactly
the same logic for enabling the supply and the regulator.
2. Let's properly set use_count when we enable always-on or boot-on
regulators even for those that don't have supplies. The previous
commit 1fc12b0589 ("regulator: core: Avoid propagating to
supplies when possible") only did this right for regulators with
supplies.
3. Let's make it clear that the only time we need to enable the supply
in regulator_resolve_supply() is if the main regulator is currently
in use. By using use_count (like the rest of the code) to decide
if we're going to enable our supply we keep everything consistent.
Overall the new scheme should be cleaner and easier to reason about.
In addition to fixing regulator_summary to be more correct (because of
the more correct use_count), this change also has the effect of no
longer using _regulator_is_enabled() in this code path.
_regulator_is_enabled() could return an error code for some regulators
at bootup (like RPMh) that can't read their initial state. While one
can argue that the design of those regulators is sub-optimal, the new
logic sidesteps this brokenness. This fix in particular fixes
observed problems on Qualcomm sdm845 boards which use the
above-mentioned RPMh regulator. Those problems were made worse by
commit 1fc12b0589 ("regulator: core: Avoid propagating to supplies
when possible") because now we'd think at bootup that the SD
regulators were already enabled and we'd never try them again.
Fixes: 1fc12b0589 ("regulator: core: Avoid propagating to supplies when possible")
Reported-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S2MPS11 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the TPS65090 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S5M8767 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the DA9211 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe path of this driver is a bit complex: sometimes the
GPIO descriptor is passed to the regulator core, sometimes
it is not.
To handle it in a simple way: stick with the devm_* resource
management and unhinge the GPIO descriptor devres handling
right before passing it to the regulator core, if we pass it
to the regulator core.
Fixes: e7d2be696f ("regulator: max8973: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get_from_of_node() rather than the devm_*
version so that the regulator core can handle the lifecycle
of these descriptors.
Fix up the errorpath so that we free this descriptor if
an error occurs in the callback. Rely on the regulator
core to deal with it after this point: a previous patch
fixed up the regulator core to properly dispose any
GPIO descriptors once you call regulator_register().
Fixes: 96392c3d8c ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: d7a261c2d1 ("regulator: max8952: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: 2468f0d515 ("regulator: lp8788-ldo: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: b2d751b7f6 ("regulator: lm363x: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a GPIO descriptor is passed to the regulator_register()
function inside the config->ena_gpiod callers must be
sure that once they call this API the regulator core
owns that descriptor and will make sure to issue
gpiod_put() on it, no matter whether the call is
successful or not.
For device tree regulators, the regulator core will
automatically set up regulator init data from the device
tree when registering a regulator by calling
regulator_of_get_init_data() which in turn calls down to
the regulator driver's .of_parse_cb() callback.
This callback (in drivers such as for max77686) may also
choose to fill in the config->ena_gpiod field with a GPIO
descriptor.
Harden the errorpath of regulator_register() to
properly gpiod_put() any passed in cfg->ena_gpiod
or any gpiod coming from the device tree on any type
of error.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Support Opensource <support.opensource@diasemi.com>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently it is expected that regulator init data will be defined as a
series of sub-nodes from the node that bound in the driver. Add support
for a node to both bind in a driver and contain init data for that
regulator.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support future additions factor out the location of the OF node
containing the init data for the regulator from the code that parses the
init data.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP20X driver currently has several masks defined throughout the
code. Use nice defines to make them clean and more descriptive.
Additionally include bitops.h, which was missing before, and sort
headers.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prior to commit 5451781dad ("regulator: core: Only count load for
enabled consumers") we used to always add up the total load on every
enable in _regulator_enable(). After that commit we only updated the
total load when enabling / disabling a regulator where a consumer
specified a load or when changing the consumer load on an enabled
regulator.
The problem with the new scheme is that if there is a system load
specified for a regulator but no consumers specify a load then we
never account for it.
Let's account for the system load in set_machine_constraints().
NOTE: with the new scheme we end up with a bit of a quandry. What if
someone specifies _both_ an initial mode and a system load? If we
take the system load into account right at init time then it will
effectively clobber the initial mode. We'll resolve this by saying
that if both are specified then the initial mode will win. The system
load will then only take effect if/when a consumer specifies a load.
If no consumers ever specify a load then the initial mode will persist
and the system load will have no effect.
Fixes: 5451781dad ("regulator: core: Only count load for enabled consumers")
Reported-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is marked as always on, it is enabled early on, when
checking and setting up constraints. It makes the assumption that the
bootloader properly initialized the regulator, and just in case enables
the regulator anyway.
Some constraints however currently get missed, such as the soft-start
and ramp-delay. This causes the regulator to be enabled, without the
soft-start and ramp-delay being applied, which in turn can cause
high-currents or other start-up problems.
By moving the always-enabled constraints later in the constraints check,
we can at least ensure all constraints for the regulator are followed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we called regulator_enable() on a regulator we'd end up
propagating that call all the way up the chain every time. This is a
bit of a waste of time. A child regulator already refcounts its own
enables so it should avoid passing on to its parent unless the
refcount transitioned between 0 and 1.
Historically this hasn't been a huge problem since we skipped dealing
with enable for always-on regulators. In a previous patch, however,
we removed the always-on optimization. On one system, the debugfs
regulator_summary was now showing a "use_count" of 33 for a top-level
regulator.
Let's implement this optimization. This turns out to be fairly
trivial with the recent reorganization of the regulator core.
NOTE: as part of this patch I'll make "always-on" regulators start
with a use count of 1. This keeps the counts clean when recursively
resolving regulators.
ALSO NOTE: this commit also contains somewhat of a bug fix to
regulator_force_disable(). It was incorrectly looping over
"rdev->open_count" when it should have been looping over use_count.
We have to touch that code anyway (since we should no longer loop at
all), so we'll fix it together in one patch. Also: since this comes
after commit f8702f9e4a ("regulator: core: Use ww_mutex for
regulators locking") we can now move to use _regulator_disable() for
our supply and keep it in the lock.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In general when the consumer of a regulator requests that the
regulator be disabled it no longer will be drawing much load from the
regulator--it should just be the leakage current and that should be
very close to 0.
Up to this point the regulator framework has continued to count a
consumer's load request for disabled regulators. This has led to code
patterns that look like this:
enable_my_thing():
regular_set_load(reg, load_uA)
regulator_enable(reg)
disable_my_thing():
regulator_disable(reg)
regulator_set_load(reg, 0)
Sometimes disable_my_thing() sets a nominal (<= 100 uA) load instead
of setting a 0 uA load. I will make the assertion that nearly all (if
not all) places where we set a nominal load of 100 uA or less we end
up with a result that is the same as if we had set a load of 0 uA.
Specifically:
- The whole point of setting the load is to help set the operating
mode of the regulator. Higher loads may need less efficient
operating modes.
- The only time this matters at all is if there is another consumer of
the regulator that wants the regulator on. If there are no other
consumers of the regulator then the regulator will turn off and we
don't care about the operating mode.
- If there's another consumer that actually wants the regulator on
then presumably it is requesting a load that makes our nominal
<= 100 uA load insignificant.
A quick survey of the existing callers to regulator_set_load() to see
how everyone uses it:
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator core takes over managing the lifetime of the enable GPIO
once the regulator is registered. As such we shouldn't register the
enable GPIO using devm, or it will be freed twice.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the commit f8702f9e4a ("regulator: core: Use ww_mutex for
regulators locking") disabling of the supply was moved into
_regulator_disable(). That means regulator_disable_work() shouldn't
be disabling since that double-disables the supply.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "requested_microamps" sysfs attribute was only being exposed for
"current" regulators. This didn't make sense. Allow it to be exposed
always.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on review comments on the MFD driver, move the child drivers for
the Lochnagar MFD over to binding through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO descriptor array must be zero initialized to ensure that core will
properly handle also the case when no external GPIO pin is defined.
Fixes: 1c984942f0 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes compiling regulator drivers that use these function when
these drivers are built as kernel modules.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's unlikely that regulators may disappear/appear while regulators
debug-summary is being prepared, but let's be consistent and avoid that
situation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether supply regulator is the couple to avoid infinite recursion
during of locking.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Wait/wound mutex shall be used in order to avoid lockups on locking of
coupled regulators.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up from the device tree configuration node.
Tested on Odroid U3 (with max77686 although not using any GPIOs
for regulators, so at least default paths are not broken).
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Cc: patches@opensource.cirrus.com
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Tested on Odroid XU3 (with s2mps11 although not using any GPIOs
for regulators, so at least default paths are not broken).
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD71837 and BD71847 have a HW functionality which leave power
rails OFF after powerof state:
- if they have been controlled by SW.
- if state transition from poweroff is done to SNVS
BD71837 can after reset transition from power-off to SNVS or
READY state depending on reset reason. By default only wathcdog
reset changes state from poweroff to ready. Change PMIC
configuration to always transition to READY in order to avoid
crucial power rails being OFF after reset.
If SNVS is required the crucial power rails should not be
controlled by SW - eg corresponding regulator control register
should have SEL bit kept zero. Currently the driver assumes all
regulators to be controlled by SW so it sets all SEL bits to 1.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltages in bd718xx_3rd_nodvs_buck_volts are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the according constraints for PM_SUSPEND_STANDBY case.
Previously, only suspend to mem/disk were taken into
consideration.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators shall be uncoupled if one of the couples disappear.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On NVIDIA Tegra30 there is a requirement for regulator "A" to have voltage
higher than voltage of regulator "B" by N microvolts, the N value changes
depending on the voltage of regulator "B". This is similar to min-spread
between voltages of regulators, the difference is that the spread value
isn't fixed. This means that extra carefulness is required for regulator
"A" to drop its voltage without violating the requirement, hence its
voltage should be changed in steps so that its couple "B" could follow
(there is also max-spread requirement).
Add new "max_uV_step" constraint that breaks voltage change into several
steps, each step is limited by the max_uV_step value.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't allow to get regulator until all of its couples resolved because
consumer will get EPERM and coupling shall be transparent for the drivers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If registered regulator found a couple, then the couple can find the
registered regulator too and hence coupling can be mutually resolved
at the registration time.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Uncoupled regulators should be a special case of coupled regulators, so
they should share a common voltage setting path. When enabling,
disabling or setting voltage of a coupled regulator, all coupled
regulators should be locked. Regulator's supplies should be locked, when
setting voltage of a single regulator. Enabling a coupled regulator or
setting its voltage should not be possible if some of its coupled
regulators, has not been registered.
Add function for locking coupled regulators and supplies. Extract
a new function regulator_set_voltage_rdev() from
regulator_set_voltage_unlocked(), which is called when setting
voltage of a single regulator.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Introduce new function regulator_balance_voltage(), which
keeps max_spread constraint fulfilled between a group of coupled
regulators. It should be called if a regulator changes its
voltage or after disabling or enabling. Disabled regulators should
follow changes of the enabled ones, but their consumers' demands
shouldn't be taken into account while calculating voltage of other
coupled regulators.
Find voltages, which are closest to suiting all the consumers' demands,
while fulfilling max_spread constraint, keeping the following rules:
- if one regulator is about to rise its voltage, rise others
voltages in order to keep the max_spread
- if a regulator, which has caused rising other regulators, is
lowered, lower other regulators if possible
- if one regulator is about to lower its voltage, but it hasn't caused
rising other regulators, change its voltage so that it doesn't break the
max_spread
Change regulators' voltages step by step, keeping max_spread constraint
fulfilled all the time. Function regulator_get_optimal_voltage()
should find the best possible change for the regulator, which doesn't
break max_spread constraint. In function regulator_balance_voltage()
optimize number of steps by finding highest voltage difference on
each iteration.
If a regulator, which is about to change its voltage, is not coupled,
method regulator_get_optimal_voltage() should simply return the lowest
voltage fulfilling consumers' demands.
Coupling should be checked only if the system is in PM_SUSPEND_ON state.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
0-Day tests found compilation error on x86.
Driver won't compile on x86_64 as "of_match_ptr" is
not found. Add missing include <linux/of.h>
At some point this fix was lost. So re-apply it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Review of the MFD component has stated we should not include the
register headers through lochnagar.h and thus removed them from that
header. Explicitly include them in the end drivers manually.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1:
drivers/regulator/bd718x7-regulator.c: In function ‘bd718xx_probe’:
drivers/regulator/bd718x7-regulator.c:1020: warning: initialization from incompatible pointer type
drivers/regulator/bd718x7-regulator.c:1024: warning: initialization from incompatible pointer type
Apparently this old compiler can't handle the obscure double
indirection.
However, there is no need for a double indirection. Just store a
pointer to the array instead, like other drivers tend to do.
Fixes: 494edd266b ("regulator/mfd: Support ROHM BD71847 power management IC")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently supports coin cell / super cap charging, so
this patch extends it to support PF0100.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the GPIO
descriptor API, there's a small addition to the GPIO API plus a bunch of
updates to board files to implement it. This is some really welcome
work from Linus Walleij that's had a bunch of review and has been
sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvNyl0THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DubB/4nWL/XSUb7qIm2fjjMUffelfk4/viB
MZg3JPEMr7ahK+QC1RQ5nOmkuACSU3Uij8RE1omLp5isfCiSa+e17f9uQx4Cn/pw
9DsIeJUEC4LvZ9gA9pDf0313B/0BIYfOMJToyLgwTNmJl+T+0e59RcS4TTCEqxwD
PmpPakOvCTD6YuVI7HhYL/HXJK1buvrAiENSjCyfyJTDaMSzJl6WMn+eibFaZbDn
NXwj2W+QyuiFCdl/7/4NWaqhlyOvM05ivnnLM/SPMBj+Iu4gSZ0PX81z98eZ3M66
YSPhF2o5SkhhffFx5xjpgR3VquXDVb0oefzhvJmZYHXi7ZKKMruoYaGB
=Ztu3
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the
GPIO descriptor API, there's a small addition to the GPIO API plus a
bunch of updates to board files to implement it. This is some really
welcome work from Linus Walleij that's had a bunch of review and has
been sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices"
* tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: lochnagar: Use a consisent comment style for SPDX header
regulator: bd718x7: Remove struct bd718xx_pmic
regulator: Fetch enable gpiods nonexclusive
regulator/gpio: Allow nonexclusive GPIO access
regulator: lochnagar: Add support for the Cirrus Logic Lochnagar
regulator: stpmic1: Return REGULATOR_MODE_INVALID for invalid mode
regulator: stpmic1: add stpmic1 regulator driver
dt-bindings: regulator: document stpmic1 pmic regulators
regulator: axp20x: Mark expected switch fall-throughs
regulator: bd718xx: fix build warning on x86_64
regulator: fixed: Default enable high on DT regulators
regulator: bd718xx: rename bd71837 to 718xx
regulator: bd718XX use pickable ranges
regulator/mfd: bd718xx: rename bd71837/bd71847 common instances
regulator: Support regulators where voltage ranges are selectable
mfd: dt bindings: add BD71847 device-tree binding documentation
regulator: dt bindings: add BD71847 device-tree binding documentation
regulator/mfd: Support ROHM BD71847 power management IC
regulator: da905{2,5}: Remove unnecessary array check
regulator: qcom: Add PMS405 regulators
...
Update the rest of the comment at the start of the file to also use C++
style comments to match the required style of the SPDX header.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the fields in struct bd718xx_pmic are not really necessary.
Remove struct bd718xx_pmic to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the core regulator code is treating GPIO descriptors as
nonexclusive, i.e. it assumes that the enable GPIO line may be
shared with several regulators, let's add the flag introduced
for fixing this problem on fixed regulators to all drivers
fetching GPIO descriptors to avoid possible regressions.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
The Lochnagar board provides power supplies for the attached
CODEC/Amp device. Currently this driver supports the microphone
supplies and the digital core voltage for the attached
device. There are some additional supplies that will be
added in time but these supplies are sufficient for most
systems/use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stpmic1 PMIC embeds several regulators and switches with
different capabilities.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I moved the whole comment
"Fall through to the check below.", which contains the "Fall through"
comment, at the bottom of the case, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 1436594 ("Missing break in switch")
Addresses-Coverity-ID: 1364475 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit efdfeb079c
("regulator: fixed: Convert to use GPIO descriptor only")
switched to use gpiod_get() to look up the regulator from the
gpiolib core whether that is device tree or boardfile.
This meant that we activate the code in
a603a2b8d8 ("gpio: of: Add special quirk to parse regulator flags")
which means the descriptors coming from the device tree already
have the right inversion and open drain semantics set up from
the gpiolib core.
As the fixed regulator was inspected again we got the
inverted inversion and things broke.
Fix it by ignoring the config in the device tree for now: the
later patches in the series will push all inversion handling
over to the gpiolib core and set it up properly in the
boardfiles for legacy devices, but I did not finish that
for this kernel cycle.
Fixes: commit efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuM/8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Az7B/4ye6MIEn8hwKmS36NU3oCvCTFiOZHe
W+T1/O7gOYPSOeHk/4SA8v+A0X2ry+zCschSJtnGDWeZwiZmuhSbQO3SKKM+iAKJ
R1UFioMVd8cr8UySX0ddSdFit+rI+FcZHd8TYAjbseX+0YKZX7z7/rXPVhSEhdU3
BxRy58DJRbLxYofiGruvDd/sj6VFukVmLRjQUE5SqZ8aTKXBbrT7h0Jgi3m7aOmK
g/a+ulMNecq8884oQuBjj1+xCuT02GJsT04BKaXEBsAFX1Fh8IyOxej2N2PaX1z/
6HoPjSAac/Gl9BAgpV0YDdEJJR8yumkdDJubF3SayMyoiv16zMTT1fvC
=t0Ni
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuNaMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H/3B/9u/IGN9LWSnauAivTDqZGx1V3a97e2
ijZSiWaTWFmIBPUNIJgDQirdqsX61Mgu9mTbeD9+tmi2Mm4AOZRJT4pdtzZCehWT
HQuN4dcF9heftf/6Q4c+5yZFAJzOJHHuFklNdDAuM12rUp5IDpKxIo2nrx7MDN6r
RgrxK6eTluvOL4+VJwN/VqXRBWfN857uMjaGkbFV3CrYJh2Ktumts3IcFd18Cpvd
U3gBUYNsPBiQtmGXFkrCCBaYWqn5Ry91CAvpTjoJdZx50xbeXVOEUnUMaidQ4/ru
XL+PqcdTovKuV5OhMzra5MCVt3Cv8Oc/21KeNvFEIV3X6O531LEcksDx
=zN+p
-----END PGP SIGNATURE-----
Merge tag 'bd71847-support' into regulator-4.20
regulator/mfd: Support for the ROHM BD71847
This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.
rename bd71837-regulator.c to bd718x7-regulator.c to reflect the
fact that also BD71847 is now supported by the driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Few regulators in BD71837 and BD71847 can output voltages from
different voltage ranges. Register interface is arranged so that
used range is selected by toggling bits which are not next to actual
voltage selection bits. Then the voltage inside selected range is
determined by voltage selection bits (as usual). Support BD71837
and BD71847 selectible range voltages using new pickable ranges
helpers.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename parts of code that support both BD71837 and BD71847 to BD718XX.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For example ROHM BD71837 and ROHM BD71847 Power management ICs have
regulators which provide multiple linear ranges. Ranges can be
selected by individual non contagious bit in vsel register. Add
regmap helper functions for selecting ranges.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD71847 is reduced version of BD71837. DVS bucks 3 and 4 are
removed as is LDO7. Voltage ranges of some regulators are
expanded.
Add initial support for BD71847 with BD71837 driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of fairly minor bug fixes here, a couple of driver specific
ones plus two core fixes. There's one fix for the new suspend state
code which fixes some confusion with constant values that are supposed
to indicate noop operation and another fixing a race condition with the
creation of sysfs files on new regulators.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuL04THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GdVB/9AWbmIA8iNJDo/CETEZ9UiOvEFXSO8
vRk+WcU4vtPo4qp27ylYRh9dKjWczEq8dKpe4YmaLjv4HX5MggLiwO1cLl44+q6y
AKZYK1FvGR1yExP3adE4XEC03jD21909mkLCNRawCVh+Iorp4r5CA6ahNfzT0flI
Eo5nKi4zN/0WSjxcoDdqUQ7oIivlmxiC8HYZyluS7f6UV0rcQXeqdXKqs6utPUxD
w4MLQriPqG7R0g75XqoRB7hVcZBO4m/NRi6SMGQtF1WG1unpl+iCnxRa0WXHi1th
nMg900nucgIe6gWBxMocWbyXsFj3+CrWlCB4BxVW8+pe8VyLFtYnPUA5
=yAAv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuMasTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NPZB/0X1e0JWK819dT5HWgNa6E2391fn1Qj
eY89u0cJj+3gom3QyOKCupcjEIumPHVYjiCsIEVipH+vefcuzgyUkRHhBZsSFgyp
90sVHKywg5pcxi6em/wuStzkXA84HjCVPJ4nDd6fnE6Ew7NDpP0/FPkpt7PwqlFy
b56pg/iK6YFhgXLlJMi6k7TGb/NG9M0qZzrb5UvTIbqVw9IRsqQrLN6YSaqhUFwe
hwonne4bMPl4DroVBGDz15djFv0Re7DxJuhAErJ/Fafzq5SX1zAPzkJ6peJnSdyF
2fUv6596nhNKVqAvMF5514kBq+JeFB13YS4S2Xm2Dm/rQ1P9G8XSfzQG
=YPYr
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.19-rc5' into regulator-bd718xx
regulator: Fixes for 4.19
A collection of fairly minor bug fixes here, a couple of driver specific
ones plus two core fixes. There's one fix for the new suspend state
code which fixes some confusion with constant values that are supposed
to indicate noop operation and another fixing a race condition with the
creation of sysfs files on new regulators.
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/regulator/da9052-regulator.c:423:22: warning: address of array
'pdata->regulators' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (pdata && pdata->regulators) {
~~ ~~~~~~~^~~~~~~~~~
drivers/regulator/da9055-regulator.c:615:22: warning: address of array
'pdata->regulators' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (pdata && pdata->regulators) {
~~ ~~~~~~~^~~~~~~~~~
Link: https://github.com/ClangBuiltLinux/linux/issues/142
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PMS405 provdies 5 SMPS regulators and 13 LDOs, add these to the RPM
regulator driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.
[Removed backtrace for length -- broonie]
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
0-Day tests found compilation error on x86. Driver won't
compile on x86_64 as "of_match_ptr" is not found. Add missing
include <linux/of.h>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.
Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.
It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.
The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.
Intel MID portions tested by Andy.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Acked-by: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some boards the SoC can use one pin "PMIC_STBY_REQ" to notify th PMIC
about state changes. In this case internal state of PMIC must be
preconfigured for upcomming state change.
It works fine with the current regulator framework, except with the
power-off case.
This patch is providing an optional pm_power_off_prepare handler
which will configure standby state of the PMIC to disable all power lines.
In my power consumption test on RIoTBoard, I got the following results:
power off without this patch: 320 mA
power off with this patch: 2 mA
suspend to ram: 40 mA
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix kernel-doc warning:
../drivers/regulator/core.c:4479: warning: Excess function parameter 'state' description in 'regulator_suspend'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_pm_ops with regulator_suspend and regulator_resume functions are
assigned to every regulator device registered in the system, so there is no
need to iterate over all again in them. Replace class_for_each_device()
construction with direct operation on the rdev embedded in the given
regulator device. This saves a lots of useless operations in suspend and
resume paths.
Fixes: f7efad10b5: regulator: add PM suspend and resume hooks
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators don't have all states defined and in such cases regulator
core should not assume anything. However in current implementation
of of_get_regulation_constraints() DO_NOTHING_IN_SUSPEND enable value was
set only for regulators which had suspend node defined, otherwise the
default 0 value was used, what means DISABLE_IN_SUSPEND. This lead to
broken system suspend/resume on boards, which had simple regulator
constraints definition (without suspend state nodes).
To avoid further mismatches between the default and uninitialized values
of the suspend enabled/disabled states, change the values of the them,
so default '0' means DO_NOTHING_IN_SUSPEND.
Fixes: 72069f9957: regulator: leave one item to record whether regulator is enabled
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There is a HW quirk in BD71837. The shutdown sequence timings for
bucks/LDOs which are enabled via register interface are changed.
At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
beginning of shut-down sequence. This causes LDO5/6 voltage
monitoring to detect under voltage and force PMIC to emergency
state instead of poweroff. Disable voltage monitoring for LDO5 and
LDO6 at probe to avoid this.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
No functional change here but it can make the code more readable to
have breaks in the "default" case even though it's the last case.
Let's add them.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most functions that access the rdev lock the rdev mutex before looking
at data. ...but not the code that implements the debugfs
regulator_summary. It probably should though, so let's do it.
Note: this fixes no known issues. The problem was found only by code
inspection.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's handy to see the load requested by a regulator consumer in the
regulator_summary. Add it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's handy to know what opmode a regulator has been configured to in
the summary. Add it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't give up voltage mapping if first range with suitable min/max uV
does not provide the wanted voltage.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set it once is enough.
Also move n_voltages close to volt_table for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing .owner field in regulator_desc, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Add the QCOM RPMh regulator driver to manage PMIC regulators
which are controlled via RPMh on some Qualcomm Technologies, Inc.
SoCs. RPMh is a hardware block which contains several
accelerators which are used to manage various hardware resources
that are shared between the processors of the SoC. The final
hardware state of a regulator is determined within RPMh by
performing max aggregation of the requests made by all of the
processors.
Add support for PMIC regulator control via the voltage regulator
manager (VRM) and oscillator buffer (XOB) RPMh accelerators.
VRM supports manipulation of enable state, voltage, and mode.
XOB supports manipulation of enable state.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace GPL v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MFD part for bd71837 was changed during the review. Clean regulator part to
match changed MFD:
- renamed header file => fix include
- remove unused platdata as also type definition was removed
- Kconfig option for MFD part was changed => fix depends on clause
- Rename Kconfig option for regulators
As Kconfig option for regulators gets now used (when dependency to MFD is
satisfied) change it so that it won't require new change when support for
bd71847 is added.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no check that tps->strobes is allocated successfully in
tps65217_regulator_probe().
The patch adds corresponding check.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added support for the CPCAP power management regulator functions on
Tegra based Motorola Xoom devices.
Added sw2_sw4 value tables, which provide power to the Tegra core and
aux devices.
Added the Xoom init tables and device tree compatibility match.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SW2 and SW4 use a shared table to provide voltage to the cpu core and
devices on Tegra hardware.
Added this table to the cpcap regulator driver as the first step to
supporting this device on Tegra.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
drivers/regulator/bd9571mwv-regulator.c:220:1: warning:
symbol 'dev_attr_backup_mode' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulators on pfuze100.
Based on commit 5fe156f1ca ("regulator: pfuze100: add enable/disable for
switch") which is reverted due to boot regressions by commit 464a5686e6
("regulator: Revert "regulator: pfuze100: add enable/disable for switch"").
Disabling the switch regulators will only be done if the user specifies
"fsl,pfuze-support-disable-sw" in its device tree to keep backward
compatibility with current dtb's [1].
[1] https://patchwork.kernel.org/patch/10490381/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch error:
ERROR: code indent should use tabs where possible
+ { }$
Fixes: ca5cd8c940 ("regulator: qcom_spmi: Add support for pmi8994")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch error:
ERROR: do not initialise statics to NULL
+static struct regmap *saw_regmap = NULL;
Fixes: 0caecaa872 ("regulator: qcom_spmi: Add support for SAW")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have just assigned saw_regmap, and since the error message
refers to saw_regmap, it feels safe to assume that it is saw_regmap,
and not regmap, that should be checked for errors.
Fixes: 0caecaa872 ("regulator: qcom_spmi: Add support for SAW")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For of_find_node_by_name(), you typically pass what the previous call
returned. Therefore, of_find_node_by_name() increases the refcount of
the returned node, and decreases the refcount of the node passed as the
first argument.
of_find_node_by_name() is incorrectly used, and produces a warning.
Fix the warning by using the more suitable function
of_get_child_by_name().
Also add a missing of_node_put() for the returned value, since this was
previously being leaked.
OF: ERROR: Bad of_node_put() on /soc/qcom,spmi@400f000/pmic@3/regulators
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 4.18.0-rc4-00223-gefd7b360b70e #12
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
Call trace:
dump_backtrace+0x0/0x1a8
show_stack+0x14/0x20
dump_stack+0x90/0xb4
of_node_release+0x74/0x78
kobject_put+0x90/0x1f0
of_node_put+0x14/0x20
of_find_node_by_name+0x80/0xd8
qcom_spmi_regulator_probe+0x30c/0x508
Fixes: 0caecaa872 ("regulator: qcom_spmi: Add support for SAW")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the existing support for backup mode to toggle power switches.
With a toggle power switch (or level signal), the following steps must
be followed exactly:
1. Configure PMIC for backup mode, to change the role of the
accessory power switch from a power switch to a wake-up switch,
2. Switch accessory power switch off, to prepare for system suspend,
which is a manual step not controlled by software,
3. Suspend system,
4. Switch accessory power switch on, to resume the system.
Hence the PMIC is configured for backup mode when "on" or "1" is written
to the PMIC's "backup_mode" virtual file in sysfs. Conversely, writing
"off" or "0" reverts the role of the accessory switch to a power
switch.
Unlike with momentary switches, backup mode is not enabled by default,
as enabling it prevents the board from being powered off using the power
switch, which may confuse the user.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the BD9571MWV PMIC driver uses the standard "wake_up" sysfs
file to control enablement of DDR Backup Mode.
However, configuring DDR Backup Mode is not really equivalent to
configuring the PMIC as a wake-up source. To avoid confusion, use a
custom "backup_mode" attribute file in sysfs instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit to add support for regulators implemented in UniPhier SoCs.
This supports USB VBUS only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code generates a static cehcker warnings because "rid < 0"
is always false:
drivers/regulator/max8997-regulator.c:169 max8997_list_voltage()
warn: condition is always false
The problem is that because of type promotion, if "rid" is negative the
comparison against ARRAY_SIZE() is type promoted to size_t and it's
treated as a very high positive value. I've changed the order of the
checks so now everyone is happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a device link between the consumer and the driver so that
the consumer is not suspended before the driver. The goal is to avoid
implementing suspend_late ops in regulator drivers.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change suspend_late ops to suspend normal ops. The goal is to avoid
requesting all the regulator drivers to be operational in suspend late
phase.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the LDOs present only on DA9063 at the end of the list, so that
the DA9063L can simply indicate less LDOs and still share the list of
regulators with DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The model number stored in the struct da9063 is the same for all
variants of the da9063 since it is the chip ID, which is always
the same. Replace that with a separate identifier instead, which
allows us to discern the DA9063 variants by setting the type
based on either DT match or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC_DA9063 is a complete misnomer, it denotes the value of the
DA9063 chip ID register, so rename it as such. It is also the value
of chip ID register of DA9063L though, so drop the enum as all the
DA9063 "models" share the same chip ID and thus the distinction will
have to be made using DT or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit 5fe156f1ca.
Commit 5fe156f1ca ("regulator: pfuze100: add enable/disable for switch")
causes boot regression on some platforms such as imx6sl-evk and
imx6sll-evk.
After this commit the SW4 regulator will be turned
off and since it supplies the DDR voltage on these boards, a
kernel hang is observed.
Revert it to avoid breaking old dtb's.
Fixes: 5fe156f1ca ("regulator: pfuze100: add enable/disable for switch")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Address issues spotted by Andy Shevchenko during review of original patch
No functional changes intended
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the enable GPIO is being looked up on the regulator
device itself but that does not have its own DT node, this causes
the lookup to fail and the regulator not to get its GPIO. The DT
node is shared across the whole MFD and as such the lookup needs
to happen on that parent device. Moving the lookup to the parent
device also means devres can no longer be used as the life time
would attach to the wrong device.
Additionally, the enable GPIO is active high so we should be passing
GPIOD_OUT_LOW to ensure the regulator starts in its off state allowing
the driver to enable it when it is ready.
Fixes: e1739e86f0 ("regulator: arizona-ldo1: Look up a descriptor and pass to the core")
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This extends the pfuze100 driver with pfuze3001 support.
Latest datasheet:
https://www.nxp.com/docs/en/data-sheet/PF3001.pdf
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned out
to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from Maciej
Purski, unfortunately there are further problems there so the last
couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW regulators
on Qualcomm SPMI and dropped support for some preproduction chips
that never made it to market from the AB8500 driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlsarcETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B4HB/9MFV/MK7Hw2hsVCX3qWTiH4tJ/X0MG
tGz1PfmbH0CJ9ly5g+rvCoT+1/s7BydKzi1cd1RHnimBv2U1XagwSny3LNEcJs2Q
pmhpGViakkQI/Y2h+u/j0Jk1nE+jTiKk+1ozUB7YnPekrGyQlf7TMhvKOLTvLKyX
56jdNxcW0MgSnXV2N6y4NpWhgvrQwvKjacTxV5iX7WP2rnK2WNFeG7Q859buhtI0
znRi+tO5hZsw5T44ickdPfotZn+i5o7MYLCkkaA2h1EwtpbYwVINfUjp3KtuyFhH
3B9GmCsjjN2Z2eInnkpzWfVXK2S1Vlp6+ka2FSs+U/4rVdd3Bw2KkblS
=Ftua
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned
out to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from
Maciej Purski, unfortunately there are further problems there so the
last couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW
regulators on Qualcomm SPMI and dropped support for some preproduction
chips that never made it to market from the AB8500 driver"
* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
regulator: gpio: Revert
ARM: pxa, regulator: fix building ezx e680
regulator: Revert coupled regulator support again
regulator: wm8994: Fix shared GPIOs
regulator: max77686: Fix shared GPIOs
regulator: bd71837: BD71837 PMIC regulator driver
regulator: bd71837: Devicetree bindings for BD71837 regulators
regulator: gpio: Get enable GPIO using GPIO descriptor
regulator: fixed: Convert to use GPIO descriptor only
regulator: s2mps11: Fix boot on Odroid XU3
dt-bindings: qcom_spmi: Document SAW support
regulator: qcom_spmi: Add support for SAW
regulator: tps65090: Pass descriptor instead of GPIO number
regulator: s5m8767: Pass descriptor instead of GPIO number
regulator: pfuze100: Delete reference to ena_gpio
regulator: max8952: Pass descriptor instead of GPIO number
regulator: lp8788-ldo: Pass descriptor instead of GPIO number
regulator: lm363x: Pass descriptor instead of GPIO number
regulator: max8973: Pass descriptor instead of GPIO number
regulator: mc13xxx-core: Switch to SPDX identifier
...
regulator: fixed/gpio: Revert GPIO descriptor changes due to platform breakage
Commit 6059577cb2 "regulator: fixed: Convert to use GPIO descriptor
only" broke at least the ams-delta platform since the lookup tables
added to the board files use the function name "enable" while the driver
uses NULL causing the regulator to not acquire and control the enable
GPIOs. Revert that and a couple of other commits that are caught up
with it to fix the issue:
2b6c00c157 "ARM: pxa, regulator: fix building ezx e680"
6059577cb2 "regulator: fixed: Convert to use GPIO descriptor only"
37bed97f00 "regulator: gpio: Get enable GPIO using GPIO descriptor"
Reported-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Revert the last two commits of the voltage coupling mechanism patch set:
456e7cdf3b regulator: core: Change voltage setting path
696861761a regulator: core: Add voltage balancing mechanism
as they broke boot on OMAP again.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3c6b38d45f "regulator: wm8994: Pass
descriptor instead of GPIO number" as it has problems with shared
GPIOs similar to that on s2mps11.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit c89c00e2b8 "regulator: max77686: Pass descriptor
instead of GPIO number" as it has problems with shared GPIOs similar to
that on s2mps11.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for controlling the 8 bucks and 7 LDOs the PMIC contains.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We augment the GPIO regulator to get the *enable* regulator
GPIO line (not the other lines) using a descriptor rather than
a global number.
We then pass this into the regulator core which has been
prepared to hande enable descriptors in a separate patch.
Switch over the two boardfiles using this facility and clean
up so we only pass descriptors around.
Cc: Philipp Zabel <philipp.zabel@gmail.com> # HX4700/Magician maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.
Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.
The OMAP didn't have proper label names on its GPIO chips so I have fixed
this with a separate patch to the GPIO tree, see
commit 088413bc0b
"gpio: omap: Give unique labels to each GPIO bank/chip"
It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.
The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.
For the patch hunk hitting arch/blackfin I would say I do not expect
testing, review or ACKs anymore so if it works, it works.
The hunk hitting the x86 BCM43xx driver is especially tricky as the number
comes out of SFI which is a mystery to me. I definately need someone to
look at this. (Hi Andy.)
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change to descriptors in 0369e02b75 "regulator: s2mps11: Pass
descriptor instead of GPIO number" has broken the boot on Odroid XU3
according to kernelci so let's revert that for now. We get a NULL
pointer defererence in:
[ 2.467929] [] (validate_desc) from [] (gpiod_set_value_cansleep+0x14/0x30)
[ 2.476591] [] (gpiod_set_value_cansleep) from [] (_regulator_do_enable+0x2f8/0x370)
[ 2.486032] [] (_regulator_do_enable) from [] (regulator_register+0xc54/0x1280)
[ 2.495045] [] (regulator_register) from [] (devm_regulator_register+0x40/0x7c)
[ 2.504057] [] (devm_regulator_register) from [] (s2mps11_pmic_probe+0x1c0/0x444)
[ 2.513243] [] (s2mps11_pmic_probe) from [] (platform_drv_probe+0x6c/0xa4)
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for SAW controlled regulators.
The regulators defined as SAW controlled in the device tree
will be controlled through special CPU registers instead of direct
SPMI accesses.
This is required especially for CPU supply regulators to synchronize
with clock scaling and for Automatic Voltage Switching.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We now pass a GPIO descriptor to the core instead of a global
GPIO number, if this descriptor is NULL the GPIO line is not
used. Just delete the assignment of an invalid GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
All users of this regulator use device tree so the transition is
pretty smooth.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
This driver has supported passing a LDO enable GPIO for years,
yet this facility has never been put to use in the upstream kernel.
If someone desires to put in place GPIO control for the LDOs,
this can be done by adding a GPIO descriptor table in the MFD
nexus in drivers/mfd/lp8788.c for the LDO device when spawning the
MFD children, or using a board file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If is_enabled() is not defined, regulator core will assume
this regulator is already enabled, then it can NOT be really
enabled after disabled.
Based on Li Jun's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulator on pfuze100.
Based on Robin Gong's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Uncoupled regulators should be a special case of coupled regulators, so
they should share a common voltage setting path. When enabling,
disabling or setting voltage of a coupled regulator, all coupled
regulators should be locked. Regulator's supplies should be locked, when
setting voltage of a single regulator. Enabling a coupled regulator or
setting its voltage should not be possible if some of its coupled
regulators, has not been registered.
Add function for locking coupled regulators and supplies. Extract
a new function regulator_set_voltage_rdev() from
regulator_set_voltage_unlocked(), which is called when setting
voltage of a single regulator.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
