gspca_ov519: remove non functioning contrast control for ov764x sensor
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Differentiate between ov7640 and ov7648 and handle the ov7648 320x240
on the ov519 bridge specially to fix r and b being swapped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Deegan <michael@ucc.gu.uwa.edu.au>, has reported issues with
using 640x480 mode on his ov518+ webcam. The fix for this breaks things
on my ov518+ cam (Trust 320 Sp@cecam), this patch thus adds differentiation
in the driver between the OV7620 sensor his cam has and the OV7620AE sensor
my cam has, and then only changes the init sequence for the ov518+ +
OV7620 combo which was not working for Michael.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming of VGA stv0680 based cams (instead of CIF ones) failed, because
we were using the wrong control pipe for certain commands, this patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark led on eyetoy II as inverted, I have the feeling the led needs to
be inverted for all 519 based cams (iow we got the set led code wrong), but
lets just deal with this one cam at a time to avoid breaking currently
working cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv0680 cameras currently only work when already plugged in when the system
boots (or when manually re-loading the driver after boot). This patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New gspca subdriver adding support for SN9C2028 dual-mode cameras.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you read the mail to Oliver Neukum on the linux-usb list, then you know
that I found a cure for the mysterious problem that the MR97310a CIF "type
1" cameras have been freezing up and refusing to stream if hooked up to a
machine with a UHCI controller.
Namely, the cure is that if the camera is an mr97310a CIF type 1 camera, you
have to send it 0xa0, 0x00. Somehow, this is a timing reset command, or
such. It un-blocks whatever was previously stopping the CIF type 1 cameras
from working on the UHCI-based machines.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Exit stv090x_algo() if the tuner did not lock. This might happen due to
missing signal or invalid/incomplete tuning parameters.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C gate must also be disabled, if a tuner command failed.
Otherwise the tuner mutex would be locked forever.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mclk is not 0 then it will never be set to the correct value and
the Demodulator will not work.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This gives the STV090x and improved clock signal (rectangle instead of sine).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using clk_div member of stv6110x_config structure the tuner's clock
output divider can be configured. It is set in stv6110x_attach.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed when clock input is driven from tuner and an output
divider different from 1 is used.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before there was used a static register map that could lead to issues
when there are are multiple adapters with the STV6110(A).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function stv6110x_write_regs is used to write several registers at once.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This could be useful for p.e. Common Interface applications where data rate is limited.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this change it is possible to have the same I2C address for both tuners.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the STV0900 features two demodulation paths in one chip there is
some information used by both instances of the driver when used in
dual mode. This information is now shared in an internal structure
referenced by I2C adapter and address.
Do initialisation of the demodulator only once when used in dual mode.
Moved global mutex demod_lock to internal structure.
Moved dev_ver and mclk to internal structure.
Removed unused tuner_refclk from stv090x_state.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In automatic S/S2 detection mode, locking of a DVB-S transponder could
fail when coming from a DVB-S2 transponder. This change fixes the issue
by first disabling DVB-S and DVB-S2 mode before enabling it again.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."
In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone = stv0900_set_tone
redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The two sensors ov772x and ov965x have too much differences.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of
drivers/media/dvb/bt8xx/bt878.c
Please have a look at the small patch and either pull it through
your tree, or please ack' it so Jiri can pull it through the trivial
tree.
Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009
but also present in linus tree.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And a little code refactoring/neatening around the removals
Reduces object size a little bit:
new:
$ size drivers/media/dvb/frontends/si21xx.o
text data bss dec hex filename
8984 56 1816 10856 2a68 drivers/media/dvb/frontends/si21xx.o
old:
$ size drivers/media/dvb/frontends/si21xx.o
text data bss dec hex filename
9084 56 1792 10932 2ab4 drivers/media/dvb/frontends/si21xx.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a potential null dereference in cx18_dvb_start_feed
and cx18_dvb_stop_feed. There is a check for stream being NULL,
but it is dereferenced earlier. Move the dereference after the
check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Andy Walls <awalls@radix.net>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Free ir_dev before exit.
Found by cppcheck.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found an unreachable statement in zl10039_attach. There is
a `break' followed by `goto error'. Remove that break, so that it
can handle the error.
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a memory leak in tuner_probe. It is not freed/assigned
on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a memory leak in smscore_gpio_configure. buffer is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The return of saa7164_i2caddr_to_reglen() was not tested.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
this patch fixes a memory leak which occurs when an em28xx card with DVB
extension is unplugged or its DVB extension driver is unloaded. In
dvb_fini(), dev->dvb must be freed before being set to NULL, as is done
in dvb_init() in case of error.
Note that this bug is also present in the latest stable kernel release.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the declaration of the sysfs attributes for IR's, which
must be a NULL-terminated array of struct attribute *.
Without this patch, my machine crashes when inserting a DVB card.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I was initially concerned about the weird array index (the 2 bumps
into the next row of the array). Matthias Schwarzott look at the
datasheet and it turns out it should be zl10036_init_tab[1][0] |= 0x01;
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { <+... return NULL; ...+> }
@@
expression *x;
expression y;
identifier r.f;
statement S;
@@
x = f(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If there is ever going to be a FireDTV or FloppyDTV firmware which does
not provide a minimal ASCII textual descriptor for Model_Id --- or if
the descriptor is provided indirectly in a descriptor directory ---
the ieee1394 variant of the device probe of firedtv would dereference a
NULL pointer. The firewire variant of firedtv's device probe is not
affected.
The fix makes sure that such an unexpected firmware is safely recognized
by fdtv_alloc as an unknown firmware.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not clear how to share the unlock in the case where the structure
containing the lock has to be freed. So the unlock is now duplicated, with
one copy moved before the free. The unlock label furthermore is no longer
useful and is thus deleted.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e;
identifier f;
iterator I;
statement S;
@@
*kfree(x);
... when != &x
when != x = e
when != I(x,...) S
*x->f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_nr is unsigned so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although these sizes may be the same it is better to calculate the size of
the source, than the destiny.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the VBI support work for PAL standards in addition to NTSC.
This work was sponsored by EyeMagnet Limited.
Thanks go out to Andy Walls for providing a CD containing test PAL/VBI captures
and to Steven Toth for providing a PVR-350 to do signal generation with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When firmware 1.20 was introduced, the dib0700 switched from a polling model
using a USB control message, to the messages being delivered on a USB bulk
pipe. The code I originally added would do a blocking read on the pipe with a
50ms timeout. Because the dvb-usb-remote code makes use of the global
workqueue, this resulted in the global workqueue being blocked 50% of the
time. Also, the synchronous urb_bulk_msg() call would burn excess CPU time
(reflected as an abnormal increase in the system's load average when devices
were connected).
Rework the logic so that we now setup an asynchronous callback on the bulk
pipe, so that we now only handle RC data when it arrives on the pipe. Note
that we provide a stub function for the RC polling callback so that we can
continue to leverage the shared code in dvb-usb-rc for the setting up of the
input device.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced when adding the sensor adcm1700.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When loading the register 0x49 of the page 3, the usb_control_msg() sometimes
fails with error -71 or -62.
This change skips loading the register 0x48.
Tested-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams have many interfaces with the same interface class, so the
previous interface check did not work.
The new code checks if the interface number is zero or the only one.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new names tell the image resolution: 'Scale' is the smaller image.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change fixes up saa7127_s_std() generate SECAM out, if the user has
requested a 50 Hz video standard set that only contains a request for SECAM
standards and not PAL. Only the SAA712[89] chips can generate SECAM, the
SAA712[67] chips cannot.
I was unclear on the burst start and end values - I couldn't figure out
the units - so I left them the same as for the PAL systems.
A the video decoders on both a PVR-350 (SAA7115) and an HVR-1600 (CX23418)
identify the SECAM signal generated by a SAA7129 with this patch as SECAM.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the "xceive_pin" setting from "15" to "1" for the PVR2100 -- the same as
the PVR3100H. This properly resets the XC2028 tuner on the PVR2100.
Sergey's original email report:
Hi.
Seems cx18 module has incorrect .xceive_pin value for card,
as i see lots of i2c errors in dmesg from xc2028.
i'm using 2.6.32.2, my hardware is:
00:09.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23418
Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder
[14f1:5b7a]
Subsystem: LeadTek Research Inc. Device [107d:6f27]
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at f0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Kernel driver in use: cx18
Kernel modules: cx18
Following fixes this problem for me, the rest seems working:
Reported-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Tested-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX18_CPU_SET_INDEXTABLE command was being called with the wrong number
of arguments causing the index table frame type selection mask to be set wrong.
Now the IDX stream properly sends entries for I, P, and B frames.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_G_ENC_INDEX support see the light of day.
Some notes:
1. With default capture parameters, the CX23418 seems to transfer 192 index
entries (4.5 kB worth) at 10 second intervals.
2. Index streams don't seem to be supported for MPEG 2 TS streams
3. The index entries seem to claim every frame is a B-Frame. Possible
firmware bug.
4. The cx18 driver does not try to capture an index stream when inserting
sliced VBI into the MPEg stream as the offsets would need fixup.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the v4l2 spec, very old MPEG index entries needs to be discarded
in favor of newer index entries. This change ensures the firmware always has
buffers for index entries at the expense of the oldest unread buffers.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change starts the IDX stream along with the MPG stream as an internal
use (only) stream much like the VBI stream can be started as an internal use
stream for inserting sliced VBI packets.
The IDX stream is not started automatically with an MPEG strem if the IDX
stream is disabled (no buffers allocated) or if sliced VBI insertion is being
performed by the cx18 driver. The cx18 driver doing sliced VBI insertion
makes the offsets in the IDX stream inaccurate for the final MPEG stream
presented to user space. Since fixing the IDX offsets ourselves is not easy
and we cannot easily do what ivtv does to fix the offsets, we'll make sliced
VBI insertion and MPEG Index capture mutually exclusive for now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change allows the IDX stream to be started and stopped as any other
stream even though it has no associated device node. This is needed for
cx18 driver internal use.
Also always tell the CX23418 to generate index entries when an analog capture
starts and the IDX stream has had buffers allocated (i.e. is enabled).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a long standing memory leak of stream buffers for streams that did not
have a struct video_device allocated: namely the TS and IDX streams.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the module options related to INDEX stream buffer allocation. A single
CX2341[5678] index entry is only 24 bytes. Large buffers for the IDX stream
will prevent the CX23418 from transferring index data over at all. Buffers
of around 1.5 kB or 64 index entries seem to be just fine. We'll default to
63 buffers/MDLs as that is the firmware limit per stream and IDX stream buffers
are not high rate. There is no reason on earth to allocate the previous 1 MB
default of buffer space for the IDX stream.
This is in anticipation of implementing the G_ENC_INDEX ioctl() in the cx18
driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ctrls field of struct sd_desc is declared as const
in gspca.h. It is worth to initialize the content also with
constant values.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function callbacks in sd_desc are defined at compile time and
they do not change at runtime. Make the sd_desc initializations const.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB video interface was checked as having the number zero, but
some webcams have other values. The test is now done on the interface
class which may be either 255 (vendor spec) or 0 (class per interface).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- adapt the start sequences from the info file of the ms-win driver
of the webcams 046d:08a2/046d:08aa (lvWIMv.inf)
- disable the brightness for this sensor
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- have 2 tables for sensor probe
- with the same ID, the sensor mi1320 is found with the bridge vc0321,
the sensor mi1320_soc with the bridge vc0323
- add some comments
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added a new initialization method for Aiptek DV T300.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13708
Tested-by: Hámorszky Balázs <balihb@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently all probed sensor types are emitted in the kernel log, generating unnecessary noise. Be less verbose and only report what sensor is found (if any)
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam 0ac8:303b may have the sensors HV7131B or HV7131R(c).
This changeset checks the HV7131 type.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ID was found in a webcam 0ac8:301b.
Signed-off-by: Luis Maia <lmaia@royalhat.org>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This flag permits subdrivers to create specific transfer URBs.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/buildtest/v4l-dvb-master/v4l/ir-keytable.c: In function 'ir_setkeycode':
/home/v4l/buildtest/v4l-dvb-master/v4l/ir-keytable.c:190: warning: 'newkeymap' may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, if RF is locked but demod is not locked, it will report:
>>> tuning status == 0x03
This happens, for example, if the device is on DVB-T, and the video
standard is ISDB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After taking a look at the driver's history and doing some tests with
DVB and ISDB-T, it was noticed that the stats were incomplete, for
ISDB-T, and weren't working for DVB.
Fixed the code and added a debug code to print the complete stats at
dmesg. This debug is useful to improve the stats of this driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on a patch originally written by Michael Krufky <mkrufky@linuxtv.org>
for a preliminar S2API spec.
The patch were ported to the S2API and had the ISDB-T API additions to
honor the auto mode, while keep allowing manual tuning.
Tested with both the original dvb-apps and the new dvb-apps-isdbt scan,
that uses a different channel.conf and uses S2API with ISDB-T extensions.
Thanks-to: Michael Krufky <mkrufky@linuxtv.org> for his first version
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Siano series of patches seemed to cause a regression on reporting DTV
statistics. Due to that, signal indication weren't received, preventing
applications like scan to work.
Tested with ISDB-T signals and got the same scan result as with a
dib0700/dib8000 device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Activate ISDB-T mode using module option default_mode=6.
hack: use 4 lower bits in frequency for segment number
[mchehab@redhat.com: fix merge conflicts and CodingStyle]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves ATBM8830 reception by using per card AGC configuration rather
than register default.
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some unknown reason, on a MacBookPro5,3 the iSight sometimes report
a different video format GUID. This patch add the other (wrong) GUID to
the format table, making the iSight work always w/o other problems.
What it should report: 32595559-0000-0010-8000-00aa00389b71
What it often reports: 32595559-0000-0010-8000-000000389b71
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The quirks module parameter is or'ed with the built-in quirks for the
device being probed. This make it impossible to disable a built-in quirk
without recompiling the driver.
Replace the built-in quirks with the quirks module parameter instead of
or'ing the values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The realtime clock provided by do_gettimeofday() is affected by time
jumps caused by NTP or DST. Furthermore, preliminary investigation
showed that SMP systems the realtime clock is based on the CPU TSC,
and those could get slightly out of sync, resulting in jitter in the
timestamps depending on which processor handles the USB interrupts.
Instead of the realtime clock, use a monotonic high resolution clock to
timestamp the buffer. As this could in theory introduce a regression
with some userspace applications expecting a realtime clock timestamp,
add a module parameter to switch back to the realtime clock.
Thanks to Paulo Assis for pointing out and investigating the issue.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As currently most drivers don't define ir_dev->props, we shouldn't assume
that this field is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Experimental patch to allow changing the IR protocol. Currently, it support
changing between RC-5 and NEC protocols.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sysfs skeleton to export remote controller information via
/sys/class/irrcv.
For now, the code doesn't do much. It just exports an attribute that
is meant to report and control the IR protocol used by the keytable.
However, the callbacks for this new attribute weren't set yet.
Also, it lacks symlinks to the used event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The five-second delay can be rather annoying, and makes the system
appear much less responsive when you connect a USB drive.
It's also not entirely clear that it is needed - the settling delay has
at least historically been an issue on some Apple iPods, for example,
and some devices have been reported to need even more than the old 5s
delay.
But before we penalize them all, let's see how bad it really is. Some
of the reasons for long delays seem to be actual historical kernel bugs
that should probably never have been papered over with a delay in the
first place (there's a Ubuntu bug report for 2.6.20 about a NULL pointer
dereference unless 'delay_use' is 8 or more, for example).
It also looks like some distros have already shipped with delay_use=0,
so the five second default may well be totally historical.
In other words: "Let's see if anybody screams".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
spi: Correct SPI clock frequency setting in spi_mpc8xxx
spi/spi_s3c64xx.c: Fix continuation line formats
spi/dw_spi: Fix dw_spi_mmio to depend on HAVE_CLK
spi/dw_spi: Allow dw_spi.c to be a module
spi/dw_spi: mmio code style fixups
Memory-mapped dw_spi driver
spi/dw_spi: fix missing export of dw_spi_remove_host
spi/dw_spi: conditional transfer mode changes
spi/dw_spi: remove conditional from 'poll_transfer'.
spi/dw_spi: fixed a spelling typo in a warning message.
spi/dw_spi: add return value to empty mrst_spi_debugfs_init()
spi/dw_spi: enable platform specific chipselect.
spi/dw_spi: add a FIFO depth detection
spi/dw_spi: fix __init/__devinit section mismatch
spi: xilinx_spi: Fix up I/O routine wrapping bogosity.
spi/spi_imx: add device information by switching pr_debug() to dev_dbg()
spi: update MSIOF includes
spi/dw_spi: refine the IRQ mode working flow
spi/dw_spi: add a missed dw_spi_remove_host() in exit sequence
spi/dw_spi: bug fix in wait_till_not_busy()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (41 commits)
HID: usbhid: initialize interface pointers early enough
HID: extend mask for BUTTON usage page
HID: hid-ntrig: Single touch mode tap
HID: hid-ntrig: multitouch cleanup and fix
HID: n-trig: remove unnecessary tool switching
HID: hid-ntrig add multi input quirk and clean up
HID: usbhid: introduce timeout for stuck ctrl/out URBs
HID: magicmouse: coding style and probe failure fixes
HID: remove MODULE_VERSION from new drivers
HID: fix up Kconfig entry for MagicMouse
HID: add a device driver for the Apple Magic Mouse.
HID: Export hid_register_report
HID: Support for MosArt multitouch panel
HID: add pressure support for the Stantum multitouch panel
HID: fixed bug in single-touch emulation on the stantum panel
HID: fix typo in error message
HID: add mapping for "AL Network Chat" usage
HID: use multi input quirk for TouchPack touchscreen
HID: make full-fledged hid-bus drivers properly selectable
HID: make Wacom modesetting failures non-fatal
...
Calling the ENAB method on Toshiba laptops results in notifications being
sent when laptop hotkeys are pressed. This patch simply calls that method
and sets up an input device if it's successful.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The Latitude C640 has another variation of dell in its DMI vendor entry.
Add it to the whitelist in order to enjoy the sweet fruits of software
backlight toggling.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Instead of a MODULE_DEVICE_TABLE for every acpi_driver ids table, we
create a table containing all ids to export to get a module alias for
each one.
This will fix automatic loading of the driver when one of the ACPI
devices is not present (like the accelerometer, which is not present in
some models).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Right now, we assume that the hardware rfkill switch on Dells toggles all
radio devices. In fact, this can be configured in the BIOS and so right
now we may mark a device as hardware killed even when it isn't. Add code
to query the devices controlled by the switch, and use this when
determining the hardware kill state of a radio.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Calls to communicate with system firmware via a SMI (using dcdbas)
need to use a buffer that has a physical address of 4GB or less.
Currently the dell-laptop driver does not guarantee this, and when the
buffer address is higher than 4GB, the address is truncated to 32 bits
and the SMI handler writes to the wrong memory address.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
The Mini family doesn't support smbios 17,11 although it reports it does.
Signed-off-by: Mario Limonciello <superm1@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The "hardware" switch is tied directly to a BIOS interface that will
connect and disconnect the hardware from the bus.
If you use the software interface to request the BIOS to make these
changes, the HW switch will be in an inconsistent state and LEDs may not
reflect the state of the HW.
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
dell-laptop currently fails to clean up its platform device correctly.
Make sure that it's unregistered.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The rfkill interface on Dells only sends a notification that the switch
has been changed via the keyboard controller. Add a filter so we can
pick these notifications up and update the rfkill state appropriately.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This drops the support for manually groking the files in sysfs
to turn on and off the WLAN and BT for Compal laptops in favor
of platform rfkill support.
It has been combined into a single patch to not introduce regressions
in the process of simply adding rfkill support
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
The following Dell laptops are known to have been manufacturer by Compal
and are supported by the compal-laptop platform driver
- Mini 9
- Mini 10
- Mini 12
- Mini 10v
- Inspiron 11z
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (44 commits)
Add MAINTAINERS entry for virtio_console
virtio: console: Fill ports' entire in_vq with buffers
virtio: console: Error out if we can't allocate buffers for control queue
virtio: console: Add ability to remove module
virtio: console: Ensure no memleaks in case of unused buffers
virtio: console: show error message if hvc_alloc fails for console ports
virtio: console: Add debugfs files for each port to expose debug info
virtio: console: Add ability to hot-unplug ports
virtio: console: Handle port hot-plug
virtio: console: Remove cached data on port close
virtio: console: Register with sysfs and create a 'name' attribute for ports
virtio: console: Ensure only one process can have a port open at a time
virtio: console: Add file operations to ports for open/read/write/poll
virtio: console: Associate each port with a char device
virtio: console: Prepare for writing to userspace buffers
virtio: console: Add a new MULTIPORT feature, support for generic ports
virtio: console: Introduce a send_buf function for a common path for sending data to host
virtio: console: Introduce function to hand off data from host to readers
virtio: console: Separate out find_vqs operation into a different function
virtio: console: Separate out console init into a new function
...
All of the SH clocksource drivers follow the scheme that the IRQ is setup
prior to registering the clockevent. The interrupt handler in the
clockevent cases looks to the event handler function pointer being filled
in by the registration code, permitting us to get in to situations where
asserted IRQs step in to the handler before registration has had a chance
to complete and hitting a NULL pointer deref.
In practice this is not an issue for most platforms, but some of them
with fairly special loaders (or that are chain-loading from another
kernel) may enter in to this situation. This fixes up the oops reported
by Rafael on hp6xx.
Reported-and-tested-by: Rafael Ignacio Zurita <rafaelignacio.zurita@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Mike Cui reported that his system with an NVIDIA MCP79 (aka MCP7A)
chipset stopped working with 2.6.32. The problem appears to be that
2.6.32 now enables the FPDMA auto-activate optimization in the ahci
driver. The drive works fine with this enabled on an Intel AHCI so
this appears to be a chipset bug. Since MCP79 is a fairly recent
NVIDIA chipset and we don't have any info on whether any other NVIDIA
chipsets have this issue, disable FPDMA AA optimization on all NVIDIA
AHCI controllers for now.
Should address http://bugzilla.kernel.org/show_bug.cgi?id=14922
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
While-we-investigate-issue-this-patch-looks-good-to-me-by:
Prajakta Gudadhe <pgudadhe@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
To fix a bug and address the reviewers' comments regarding the ACPI
GPE refcounting patch, do the following additional changes:
o Remove the second argument of acpi_ev_enable_gpe(),
'write_to_hardware', because it is not necessary any more.
o Add the "bad parameter" test against 'type' in
acpi_enable_gpe() and acpi_disable_gpe().
o Make acpi_enable_gpe() only check 'status' for runtime GPEs if
acpi_ev_enable_gpe() was actually called.
o Make acpi_disable_gpe() return 'status' returned by
acpi_ev_disable_gpe() and fix a bug where ACPI_GPE_TYPE_WAKE
and ACPI_GPE_TYPE_RUNTIME were exchanged by mistake.
o Add comments explaining why acpi_set_gpe() is used by the ACPI EC
driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of allocating just one buffer for a port's in_vq, fill
the entire in_vq with buffers so the host need not stall while
an application consumes the data and makes the buffer available
again for the host.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
With MULTIPORT support, the control queue is an integral part of the
functioning of the device. If we can't get any buffers allocated, the
host won't be able to relay important information and the device may not
function as intended.
Ensure 'probe' doesn't succeed until the control queue has at least one
buffer allocated for its ivq.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add the ability to remove the virtio_console module.
This aids debugging.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If unused data exists in in_vq, ensure we flush that first and then
detach unused buffers, which will ensure all buffers from the in_vq are
removed.
Also ensure we free the buffers after detaching them.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Remove port data; deregister from the hvc core if it's a console port.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If the 'nr_ports' variable in the config space is updated to a higher
value, that means new ports have been hotplugged.
Introduce a new workqueue to handle such updates and create new ports.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Remove any data that we might have in a port's inbuf when closing a port
or when any data is received when a port is closed.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The host can set a name for ports so that they're easily discoverable
instead of going by the /dev/vportNpn naming. This attribute will be
placed in /sys/class/virtio-ports/vportNpn/name. udev scripts can then
create symlinks to the port using the name.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a guest_connected field that ensures only one process
can have a port open at a time.
This also ensures we don't have a race when we later add support for
dropping buffers when closing the char dev and buffer caching is turned
off for the particular port.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Allow guest userspace applications to open, read from, write to, poll
the ports via the char dev interface.
When a port gets opened, a notification is sent to the host via a
control message indicating a connection has been established. Similarly,
on closing of the port, a notification is sent indicating disconnection.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The char device will be used as an interface by applications on the
guest to communicate with apps on the host.
The devices created are placed in /dev/vportNpn where N is the
virtio-console device number and n is the port number for that device.
One dynamic major device number is allocated for each device and minor
numbers are allocated for the ports contained within that device.
The file operation for the char devs will be added in the following
commits.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When ports get advertised as char devices, the buffers will come from
userspace. Equip the fill_readbuf function with the ability to write
to userspace buffers.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This commit adds a new feature, MULTIPORT. If the host supports this
feature as well, the config space has the number of ports defined for
that device. New ports are spawned according to this information.
The config space also has the maximum number of ports that can be
spawned for a particular device. This is useful in initializing the
appropriate number of virtqueues in advance, as ports might be
hot-plugged in later.
Using this feature, generic ports can be created which are not tied to
hvc consoles.
We also open up a private channel between the host and the guest via
which some "control" messages are exchanged for the ports, like whether
the port being spawned is a console port, resizing the console window,
etc.
Next commits will add support for hotplugging and presenting char
devices in /dev/ for bi-directional guest-host communication.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Adding support for generic ports that will write to userspace will need
some code changes.
Consolidate the write routine into send_buf() and put_chars() now just
calls into the new function.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In preparation for serving data to userspace (generic ports) as well as
in-kernel users (hvc consoles), separate out the functionality common to
both in a 'fill_readbuf()' function.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
With support for multiple ports, each port will have its own input and
output vqs. Prepare the probe function for this change.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Console ports could be hot-added. Also, with the new multiport support,
a port is identified as a console port only if the host sends a control
message.
Move the console port init into a separate function so it can be invoked
from other places.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Move out console-specific stuff into a separate struct from 'struct
port' as we need to maintain two lists: one for all the ports (which
includes consoles) and one only for consoles since the hvc callbacks
only give us the vtermno.
This makes console handling cleaner.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When multiple console support is added, ensure each port's size gets
updated when a new one is opened via hvc.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rather than assume a single port, add a 'struct ports_device' which
stores data related to all the ports for that device.
Currently, there's only one port and is hooked up with hvc, but that
will change.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now we can use an allocation function to remove our global console variable.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Keep a list of all ports being used as a console, and provide a lock
and a lookup function. The hvc callbacks only give us a vterm number,
so we need to map this.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Part of removing our "one console" assumptions, use vdev->priv to point
to the port (currently == the global console).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This makes taking locks around the get_buf vq operation easier, as well
as complements the add_inbuf() operation.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
add_inbuf() assumed one port and one inbuf per port. Remove that
assumption.
Also move the function so that put_chars and get_chars are together.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Collect port buffer, used_len, offset fields into a single structure.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We are heading towards a multiple-"port" system, so as part of weaning off
globals we encapsulate the information into 'struct port'.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We support only one virtio_console device at a time. If multiple are
found, error out if one is already initialized.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is nicer for modern R/O protection. And noone needs it non-const, so
constify the callers as well.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
To: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: linuxppc-dev@ozlabs.org
That way, we can make it const as is good kernel style. We use a separate
indirection for the early console, rather than mugging ops.put_chars.
We rename it hv_ops, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Remove old lguest-style comments.
[Amit: - wingify comments acc. to kernel style
- indent comments ]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
vq operations depend on vq->data[i] being NULL to figure out if the vq
entry is in use (since the previous patch).
We have to initialize them to NULL to ensure we don't work with junk
data and trigger false BUG_ONs.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Shirley Ma <xma@us.ibm.com>
There's currently no way for a virtio driver to ask for unused
buffers, so it has to keep a list itself to reclaim them at shutdown.
This is redundant, since virtio_ring stores that information. So
add a new hook to do this.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Allow reading various alignment values from the config page. This
allows the guest to much better align I/O requests depending on the
storage topology.
Note that the formats for the config values appear a bit messed up,
but we follow the formats used by ATA and SCSI so they are expected in
the storage world.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio is communicating with a virtual "device" that actually runs on
another host processor. Thus SMP barriers can be used to control
memory access ordering.
Where possible, we should use SMP barriers which are more lightweight than
mandatory barriers, because mandatory barriers also control MMIO effects on
accesses through relaxed memory I/O windows (which virtio does not use)
(compare specifically smp_rmb and rmb on x86_64).
We can't just use smp_mb and friends though, because
we must force memory ordering even if guest is UP since host could be
running on another CPU, but SMP barriers are defined to barrier() in
that configuration. So, for UP fall back to mandatory barriers instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
With DEBUG defined, we add an ->in_use flag to detect if the caller
invokes two virtio methods in parallel. The barriers attempt to ensure
timely update of the ->in_use flag.
But they're voodoo: if we need these barriers it implies that the
calling code doesn't have sufficient synchronization to ensure the
code paths aren't invoked at the same time anyway, and we want to
detect it.
Also, adding barriers changes timing, so turning on debug has more
chance of hiding real problems.
Thanks to MST for drawing my attention to this code...
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a fix for my earlier patch: "virtio: Add memory statistics reporting to
the balloon driver (V4)".
I discovered that all_vm_events() can sleep and therefore stats collection
cannot be done in interrupt context. One solution is to handle the interrupt
by noting that stats need to be collected and waking the existing vballoon
kthread which will complete the work via stats_handle_request(). Rusty, is
this a saner way of doing business?
There is one issue that I would like a broader opinion on. In stats_request, I
update vb->need_stats_update and then wake up the kthread. The kthread uses
vb->need_stats_update as a condition variable. Do I need a memory barrier
between the update and wake_up to ensure that my kthread sees the correct
value? My testing suggests that it is not needed but I would like some
confirmation from the experts.
Signed-off-by: Adam Litke <agl@us.ibm.com>
To: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changes since V3:
- Do not do endian conversions as they will be done in the host
- Report stats that reference a quantity of memory in bytes
- Minor coding style updates
Changes since V2:
- Increase stat field size to 64 bits
- Report all sizes in kb (not pages)
- Drop anon_pages stat and fix endianness conversion
Changes since V1:
- Use a virtqueue instead of the device config space
When using ballooning to manage overcommitted memory on a host, a system for
guests to communicate their memory usage to the host can provide information
that will minimize the impact of ballooning on the guests. The current method
employs a daemon running in each guest that communicates memory statistics to a
host daemon at a specified time interval. The host daemon aggregates this
information and inflates and/or deflates balloons according to the level of
host memory pressure. This approach is effective but overly complex since a
daemon must be installed inside each guest and coordinated to communicate with
the host. A simpler approach is to collect memory statistics in the virtio
balloon driver and communicate them directly to the hypervisor.
This patch enables the guest-side support by adding stats collection and
reporting to the virtio balloon driver.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (minor fixes)
This is needed to compile with CONFIG_VIRTIO_PCI=y,
because virtio_pci_remove is marked __devexit.
Signed-off-by: Jamie Lokier <jamie@shareable.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: bug fix for vlan + gro issue
tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
IPv6: better document max_addresses parameter
MAINTAINERS: update mv643xx_eth maintenance status
e1000: Fix DMA mapping error handling on RX
iwlwifi: sanity check before counting number of tfds can be free
iwlwifi: error checking for number of tfds in queue
iwlwifi: set HT flags after channel in rxon
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Be in TS_POLLING state during mwait based C-state entry
ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
acer-wmi: Respect current backlight level when loading
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
The main benefit of using ACPI host bridge window information is that
we can do better resource allocation in systems with multiple host bridges,
e.g., http://bugzilla.kernel.org/show_bug.cgi?id=14183
Sometimes we need _CRS information even if we only have one host bridge,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/341681
Most of these systems are relatively new, so this patch turns on
"pci=use_crs" only on machines with a BIOS date of 2008 or newer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this fills in the bus subtractive decode resources
after reading the bridge window information rather than before. Also,
print out the subtractive decode resources as we already do for the
positive decode windows.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this breaks up pci_read_bridge_bases() into separate
pieces for the I/O, memory, and prefetchable memory windows, similar to how
Yinghai recently split up pci_setup_bridge() in 68e84ff3bdc.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine. So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.
This bug does not happen when NAPI disabled. After txdone there
must be at least one free tx slot. But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.
In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new vid/pid to the cdc_ether whitelist.
Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for error return from pci_map_single/pci_map_page and clean up.
With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next:
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
Commit 4410f39109 ("fbdev: add support for
handoff from firmware to hw framebuffers") didn't add fb_destroy
operation to efifb. Fix it and change aperture_size to match size
passed to request_mem_region.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15151
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reported-by: Alex Zhavnerchik <alex.vizor@gmail.com>
Tested-by: Alex Zhavnerchik <alex.vizor@gmail.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
geode-mfgpt: restore previous behavior for selecting IRQ
The MFGPT IRQ used to be, in order of decreasing priority,
* IRQ supplied by the user as a boot-time parameter,
* IRQ previously set by the BIOS or another driver,
* default IRQ given at compile time.
Return to this behavior, which got broken when splitting the
MFGPT/clocksource driver for 2.6.33-rc1.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason. It was likely masking a bug elsewhere that's since been
fixed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.
I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe
capability offset. This reduces redundant search in PCI configuration
space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce run-time PM callbacks for the PCI bus type. Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel. If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.
Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited. The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.
Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
pci_platform_pm_ops allowing us to enable/disable the platform to
generate wake-up events for given device. Implemet this callback
for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
make the PCI-ACPI binding code register wake-up notifiers for all
PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
check if given device is capable of generating wake-up events at
run time.
Developed in cooperation with Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently it only is possible to install one system notify handler
per namespace node, but this is not enough for PCI run-time power
management, because we need to install power management notifiers for
devices that already have hotplug notifiers installed. While in
principle this could be handled at the PCI level, that would be
suboptimal due to the way in which the ACPI-based PCI hotplug code is
designed.
For this reason, modify ACPICA so that it is possible to install more
than one system notify handler per namespace node. Namely, make
acpi_install_notify_handler(), acpi_remove_notify_handler() and
acpi_ev_notify_dispatch() use a list of system notify handler objects
associated with a namespace node.
Make acpi_remove_notify_handler() call acpi_os_wait_events_complete()
upfront to avoid a situation in which concurrent instance of
acpi_remove_notify_handler() removes the handler from under us while
we're waiting for the event queues to flush.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the run_wake flag to mark all devices for which run-time wake-up
events may be generated by the platform. Introduce a new wake-up
flag, always_enabled, for marking devices that should be permanently
enabled to generate run-time events. Also, introduce a reference
counter for run-wake devices and a function that will initialize all
of the run-time wake-up fields for given device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI GPEs may map to multiple devices. The current GPE interface
only provides a mechanism for enabling and disabling GPEs, making
it difficult to change the state of GPEs at runtime without extensive
cooperation between devices.
Add an API to allow devices to indicate whether or not they want
their device's GPE to be enabled for both runtime and wakeup events.
Remove the old GPE type handling entirely, which gets rid of various
quirks, like the implicit disabling with GPE type setting. This
requires a small amount of rework in order to ensure that non-wake
GPEs are enabled by default to preserve existing behaviour.
Based on patches from Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling. In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port. [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.] However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.
For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.
Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register. At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle. If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set. After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]
Implement a driver for the PCIe PME root port service working in
accordance with the above description.
Based on a patch from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add function pci_check_pme_status() that will check the PME status
bit of given device and clear it along with the PME enable bit. It
will be necessary for PCI run-time power management.
Based on a patch from Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make pci_bridge_check_ranges() store the PCI_PREF_RANGE_TYPE_64 in
addition to IORESOURCE_MEM_64. Just like pci_read_bridge_bases().
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Handle the case where the slot bridge that doesn't get a pre-allocated
resource big enough to handle its child resources.. For example pcie
devices need 256M, but the bridge only gets 2M preallocated.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move bus_size_bridges and assign resources out of pciehp_add_bridge()
and do them all together, one time, including slot bridge, to avoid to
calling assign resources several times when there are several bridges
under the slot bridge. Using pci_assign_unassigned_bridge_resources.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For use by pciehp.
pci_setup_bridge() will not check enabled for the slot bridge, otherwise
update res is not updated to bridge BAR. That is, bridge is already
enabled for port service.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
BIOS separates IO ranges between several IOHs, and on some slots, BIOS assigns
resources to a bridge, but stops assigning resources to the device under that
bridge, because the device needs a big resource.
So:
1. allocate resources and record the failed device resources
2. clear the BIOS assigned resources of the parent bridge of failing device
3. go back and call pci assign unassigned
4. if it still fails, go up the tree, clear more bridges. and try again
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When clearing leaf bridge resources, trying to get a big enough one, we
could shrink the bridge if there is no resource under it. Confirm
against the old resource side to make sure we're increasing the
allocation.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows us to track failed allocations for later re-trying with
reallocation.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We use this in later patches to free resrouce ranges for reassignment in
an effort to support a wider variety of PCI topologies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add header file to fix build error:
drivers/pci/hotplug/ibmphp_hpc.c:135: error: implicit declaration of function 'init_MUTEX'
drivers/pci/hotplug/ibmphp_hpc.c:136: error: implicit declaration of function 'init_MUTEX_LOCKED'
drivers/pci/hotplug/ibmphp_hpc.c:797: error: implicit declaration of function 'down'
drivers/pci/hotplug/ibmphp_hpc.c:807: error: implicit declaration of function 'up'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty. Fix this by exiting early from
pci_scan_slot if there is no device in the slot.
Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt. ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found an ommitted pci_dev_put on one error path in
cpcihp_generic_init. The path is taken on !dev, but also when
dev->hdr_type != PCI_HEADER_TYPE_BRIDGE. However it omits to
pci_dev_put on the latter.
As it is fine to pass NULL to pci_dev_put, put it in there
uncoditionally.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Scott Murray <scott@spiteful.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ISDN4Linux HiSax driver family contains the last remaining users
of the deprecated pci_find_device() function. This patch creates a
private copy of that function in HiSax, and removes the now unused
global function together with its controlling configuration option,
CONFIG_PCI_LEGACY.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't print out resources without flags to avoid cluttering up the debug
output.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is a good cleanup in itself, and makes it easier to modify specific
resource types in later code.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ibmphp driver currently maps only 1KB of ebda memory area into kernel address
space during driver initialization. This causes kernel oops when the driver is
modprobe'd and it accesses memory beyond 1KB within ebda segment. The first
byte of ebda segment actually stores the length of the ebda region in
Kilobytes. Hence make use of the length parameter and map the entire ebda
region.
Signed-off-by: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found a cut&pasted memory leak in pciehp_queue_pushbutton_work
and shpchp_queue_pushbutton_work. info is not freed/assigned on all
paths. Fix that.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file). This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.
To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No longer needed and causes build breakage.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Take advantage of some gaps in the table to fit in support for AGP speeds.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the max_bus_speed and cur_bus_speed into the pci_bus. Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array. Use a single enum, and move it to
pci.h. Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions. They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all. By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.
We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports. These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI deep C-state entry had a long standing bug/missing feature, wherein we were sending
resched IPIs when an idle CPU is in mwait based deep C-state. Only mwait based C1 was using
the write to the monitored address to wake up mwait'ing CPU.
This patch changes the code to retain TS_POLLING bit if we are entering an mwait based
deep C-state.
The patch has been verified to reduce the number of resched IPIs in general and also
improves the performance/power on workloads with low system utilization (i.e., when mwait based
deep C-states are being used).
Fixes "netperf ~50% regression with 2.6.33-rc1, bisect to 1b9508f"
http://marc.info/?l=linux-kernel&m=126441481427331&w=4
Reported-by: Lin Ming <ming.m.lin@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: usbtouchscreen - extend coordinate range for Generaltouch devices
Input: polldev can cause crash in case when polling disabled
Commit 84b79f8d28 (drm/i915: Fix crash
while aborting hibernation) attempted to fix a regression introduced
by commit cbda12d77e (drm/i915:
implement new pm ops for i915), but it went too far trying to split
the freeze/suspend and resume/thaw parts of the code. As a result,
it introduced another regression, which only is visible on some systems.
Fix the problem by merging i915_drm_suspend() with
i915_drm_freeze() and moving some code from i915_resume()
into i915_drm_thaw(), so that intel_opregion_free() and
intel_opregion_init() are also executed in the freeze and thaw code
paths, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Pedro Ribeiro <pedrib@gmail.com>
Tested-by: Tino Keitel <tino.keitel@tikei.de>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check the frame control for ieee80211_is_data_qos() is true before
counting the number of tfds can be free, the tfds_in_queue only
increment when ieee80211_is_data_qos() is true before transmit; so it
should only decrement if the type match.
Remove ieee80211_is_data_qos check for frame_ctrl in tx_resp to avoid
invalid information pass from uCode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive reply_tx and ready to decrement the count for number of
tfds in queue, do error checking to prevent error condition and
tfds_in_queue become negative number.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generaltouch protocol allows for coordinates in [0, 0xffff] range and
there are devices reporting coordinates as high as 0x7fff so let's update
the driver to reflect that.
Signed-off-by: Roy Yin <yhch@generaltouch.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Relying on overflow/wrap around isn't exact because if you wrap far
enough, you get back to "valid" values.
Reported-by: Thorsten Pohlmann <pohlmann@tetronik.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: bttv: Move I2C IR initialization
V4L/DVB: Video : pwc : Fix regression in pwc_set_shutter_speed caused by bad constant => sizeof conversion.
soc-camera: mt9t112: modify exiting conditions from standby mode
V4L/DVB: cxusb: Select all required frontend and tuner modules
V4L/DVB: dvb: l64781.ko broken with gcc 4.5
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: allow alignment fault mode to be configured at kernel boot
ARM: Update mach-types
ARM: 5951/1: ARM: fix documentation of the PrimeCell bus
ARM: 5950/1: ARM: Fix build error for arm1026ej-s processor
MAINTAINERS: fix my e-mail and status for Gemini and FA526
Gemini: wrong registers used to set reg_level in gpio_set_irq_type()
ARM: 5944/1: scsi: fix timer setup in fas216.c
ARM: 5938/1: ARM: L2: export outer_cache_fns
When polled input device is opened and closed and there are no other
users of polled device, the workqueue is created and destroyed in
every open / close operation. It is probable that at some point
dynamic allocation of internal parts of the workqueue cause changes to the
workqueue.
When a work is queued to the workqueue the work struct contains pointers
to the workqueue data. If the workqueue has been changed and the work
has never been queued to the new workqueue, work-struct contains pointers
to the non-existing workqueue. This will cause crash at the work
cancellation during device close since cancellation of a work assumes
that the workqueue exists.
To prevent that, work struct is cleaned up at device close. This keeps
work struct clean for the next use.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: fix for 32bit apps
[SCSI] fcoe: Only rmmod fcoe.ko if there are no active connections
[SCSI] libfcoe: Send port LKA every FIP_VN_KA_PERIOD secs.
[SCSI] libfc: Don't assume response request present.
[SCSI] libfc: Fix e_d_tov ns -> ms scaling factor in PLOGI response.
[SCSI] libfc: call ddp setup for only FCP reads to avoid accessing junk fsp pointer
[SCSI] iscsi_tcp regression: remove bogus warn on in write path
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
sfc: SFE4002/SFN4112F: Widen temperature and voltage tolerances
sfc: Fix sign of efx_mcdi_poll_reboot() error in efx_mcdi_poll()
net-sysfs: Use rtnl_trylock in wireless sysfs methods.
net: Fix sysctl restarts...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: bump the UMS driver version number to indicate rv740 fix
drm/radeon/kms: free fence IB if it wasn't emited at IB free time
drm/ttm: fix caching problem on non-PAT systems.
drm/radeon/rv740: fix backend setup
drm/radeon/kms: fix shared ddc detection
drm/radeon/kms/rs600: add connector quirk
vgaarb: fix "target=default" passing
The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.
Based on a review of the chip datasheets and advice from the designer
of these boards:
- Raise the maximum board temperatures to the specified maximum ambient
temperatures for their PHYs plus the expected temperature bias of the
board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol. It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
http://bugzilla.kernel.org/show_bug.cgi?id=15328
This fixes a serious regression on AGP/non-PAT systems, where
pages were ending up in the wrong state and slowing down the
whole system.
[airlied: taken this from the bug as the other option is to revert
the change which caused it].
Tested-by: John W. Linville (in bug).
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just compare the i2c id since the i2c structs
may be slighly different.
Fixes fdo bug 26616.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 board lists DVI port as HDMI.
Fixes fdo bug 26605
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 77c1ff3982 fixed the userspace
pointer dereference, but introduced another bug pointed out by Eugene Teo
in RH bug #564264. Instead of comparing the point we were at in the string,
we instead compared the beginning of the string to "default".
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reported-by: Eugene Teo <eteo@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It looks like this patch -
commit 7b2519afa1
Author: Yang, Bo <Bo.Yang@lsi.com>
Date: Tue Oct 6 14:52:20 2009 -0600
[SCSI] megaraid_sas: fix 64 bit sense pointer truncation
has caused a problem for 32bit programs with 64bit os -
http://bugzilla.kernel.org/show_bug.cgi?id=15001
fix by converting the user space 32bit pointer to a 64 bit one when
needed.
[jejb: fix up some 64 bit warnings]
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Cc: Bo Yang <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The HT extension channel settings require priv->staging_rxon.channel to be
accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel
and thus HT40 could be broken unless another call to iwl_mac_config came in.
This problem was recently introduced by "iwlwifi: Fix to set correct ht
configuration"
The particular setting in which I noticed this was monitor mode:
iwconfig wlan0 mode monitor
ifconfig wlan0 up
./iw wlan0 set channel 64 HT40-
#./iw wlan0 set channel 64 HT40-
tcpdump -i wlan0 -y IEEE802_11_RADIO
would only catch HT40 packets if I issued the IW command twice.
From visual inspection, iwl_set_rxon_channel does not depend on
iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the large CDB allocation logic in sd.c means that
scsi_io_completion does not have access to the command buffer. That in
turn causes garbage to be printed when a 32-byte command fails. Move the
command printing to sd_done where the command buffer is intact. Clear
the command buffer pointer after the extended CDB has been freed.
Make scsi_print_command ignore commands with NULL CDB pointers to
inhibit printing of garbled command strings.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We dereferenced the MAINTENANCE IN array when decoding variable length
commands. Use the right array. Also consolidate identical if
statements below.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a bug in the interpretation of the ADDITIONAL CDB LENGTH (add_cdb_len)
field of SRP_CMD requests. According to the SRP specification, the layout
of this single-byte field is as follows:
* Bits 0 and 1 are reserved.
* Bits 2 to 7 represent the ADDITIONAL CDB LENGTH field, symbolically
represented as n.
* Still according to the SRP specification, the ADDITIONAL CDB section
takes 4*n bytes.
Currently libsrp is only used by the ibmvscsi driver. Since the ibmvscsi
driver doesn't support large CDB's, this bug hasn't caused any problems yet.
[jejb: use & ~3 to mask the bits]
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds IBM Power Virtual SCSI ALUA devices to the ALUA device handler.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Newer Netapp target software supports ALUA, so
this patch adds them to the scsi_dev_alua dev list.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Can be used to balance NIC/FCoE traffic distribution.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code could inadvertently skip the post processing of
port information returned from the SNS scan, if any link-flopping
asynchronous-events were received (noticed in FCAL topologies).
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The explicit logout (LOGO) issued at the end of the callback will
flush (via normal scsi_cmnd->done()) any outstanding commands
(FCP2) the firmware is holding. While iterating through the
outstanding_cmnd array in qla2x00_abort_fcport_cmds(), locking
and unlocking of the hardware spinlock, opens-up the driver to
cases where the processed SRB (sp) could be used after the
command completed from interrupt context.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Target-level resets are unlikely to complete if done after the
bus (LIP/OLS/NOS) has been reset. Perform target-level resets,
if necessary, prior to hitting the bus.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix for BSG request cleanup when the request timesout.
Proper release of driver resources used for BSG request during timeout cleanup.
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since bsg_job->reply->reply_payload_rcv_len is uninitialized
in case of failure, fc-transport triggers a warning for each command
failed.
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Earlier, Ingo Molnar posted a patch to make it so that the kernel would avoid
reading _PPC on his broken T60. Unfortunately, it seems that with Thomas
Renninger's patch last July to eliminate _PPC evaluations when the processor
driver loads, the kernel never actually reads _PPC at all! This is problematic
if you happen to boot your non-T60 computer in a state where the BIOS _wants_
_PPC to be something other than zero.
So, put the _PPC evaluation back into acpi_processor_get_performance_info if
ignore_ppc isn't 1.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Set the backlight to use the current brightness when loaded, rather than
always resetting the backlight to maximum brightness.
Fixes kernel bugzilla #14207
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Reported-by: Denis Mukhin <denis_mukhin@yahoo.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This avoids the case where an I2C IR
device is blocking audio support (at least the PV951 suffers from
this). It is also more logical to group IR support together,
regardless of the connectivity.
This fixes bug #15184:
http://bugzilla.kernel.org/show_bug.cgi?id=15184
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Regression was caused by my commit 6b35ca0d3d
which determined message size using sizeof rather than hardcoded constants.
Unfortunately pwc_set_shutter_speed reuses a 2 byte buffer for a one byte
message too so the sizeof was bogus in this case.
All other uses of sizeof checked and are ok.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This polling is needed if camera is in standby mode, but current exiting
condition is inverted.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cxusb uses the atbm8830 and lgs8gxx (not lgs8gl5) frontends and the
max2165 tuner, so it needs to select them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I'm trying to fix it on the GCC side (PR43007), but the module is
quite stupid in using ULL constants to operate on u32 values:
static int apply_frontend_param (struct dvb_frontend* fe, struct
dvb_frontend_parameters *param)
{
...
static const u32 ppm = 8000;
u32 spi_bias;
...
spi_bias *= 1000ULL;
spi_bias /= 1000ULL + ppm/1000;
which causes current GCC 4.5 to emit calls to __udivdi3 for i?86 again.
This patch fixes this issue.
Signed-off-by: Richard Guenther <rguenther@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mod_timer() takes an absolute time and not a delay as its argument.
Cc: <stable@kernel.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch (as1335) fixes a bug in scsi_sysfs_add_sdev(). Its callers
always remove the device if anything goes wrong, so it should never
remove the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1334) fixes a bug in scsi_get_host_dev(). It
incorrectly calls get_device() on the new device's target.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1333) fixes a bug in scsi_report_lun_scan(). If a
newly-allocated device can't be used, it should be deleted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
