There are several unportable uses of CKSEG0ADDR() in MIPS KVM, which
implicitly assume that a host physical address will be in the low 512MB
of the physical address space (accessible in KSeg0). These assumptions
don't hold for highmem or on 64-bit kernels.
When interpreting the guest physical address when reading or overwriting
a trapping instruction, use kmap_atomic() to get a usable virtual
address to access guest memory, which is portable to 64-bit and highmem
kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calculate the PFN of the commpage using virt_to_phys() instead of
CPHYSADDR(). This is more portable as kzalloc() may allocate from XKPhys
instead of KSeg0 on 64-bit kernels, which CPHYSADDR() doesn't handle.
This is sufficient for highmem kernels too since kzalloc() will allocate
from lowmem in KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Default the guest PRId register to represent a generic QEMU machine
instead of a 24kc on MIPSr6. 24kc isn't supported by r6 Linux kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM emulates the RDHWR instruction, decode the instruction more
strictly. The rs field (bits 25:21) should be zero, as should bits 10:9.
Bits 8:6 is the register select field in MIPSr6, so we aren't strict
about those bits (no other operations should use that encoding space).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Recognise the new MIPSr6 CACHE instruction encoding rather than the
pre-r6 one when an r6 kernel is being built. A SPECIAL3 opcode is used
and the immediate field is reduced to 9 bits wide since MIPSr6.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support in KVM for emulation of instructions in the forbidden slot
of MIPSr6 compact branches. If we hit an exception on the forbidden
slot, then the branch must not have been taken, which makes calculation
of the resume PC trivial.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MIPSr6 doesn't have lo/hi registers, so don't bother saving or
restoring them, and don't expose them to userland with the KVM ioctl
interface either.
In fact the lo/hi registers aren't callee saved in the MIPS ABIs anyway,
so there is no need to preserve the host lo/hi values at all when
transitioning to and from the guest (which happens via a function call).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
__kvm_save_fpu and __kvm_restore_fpu use .set mips64r2 so that they can
access the odd FPU registers as well as the even, however this causes
misassembly of the return instruction on MIPSr6.
Fix by replacing .set mips64r2 with .set fp=64, which doesn't change the
architecture revision.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently on a guest exception the guest's k0 register is saved to the
scratch temp register and the guest k1 saved to the exception base
address + 0x3000 using k0 to extract the Exception Base field of the
EBase register and as the base operand to the store. Both are then
copied into the VCPU structure after the other general purpose registers
have been saved there.
This bouncing to exception base + 0x3000 is not actually necessary as
the VCPU pointer can be determined and written through just as easily
with only a single spare register. The VCPU pointer is already needed in
k1 for saving the other GP registers, so lets save the guest k0 register
straight into the VCPU structure through k1, first saving k1 into the
scratch temp register instead of k0.
This could potentially pave the way for having a single exception base
area for use by all guests.
The ehb after saving the k register to the scratch temp register is also
delayed until just before it needs to be read back.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a relative branch to get from the individual exception vectors to
the common guest exit handler, rather than loading the address of the
exit handler and jumping to it.
This is made easier due to the fact we are now generating the entry code
dynamically. This will also allow the exception code to be further
reduced in future patches.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Scratch cop0 registers are needed by KVM to be able to save/restore all
the GPRs, including k0/k1, and for storing the VCPU pointer. However no
registers are universally suitable for these purposes, so the decision
should be made at runtime.
Until now, we've used DDATA_LO to store the VCPU pointer, and ErrorEPC
as a temporary. It could be argued that this is abuse of those
registers, and DDATA_LO is known not to be usable on certain
implementations (Cavium Octeon). If KScratch registers are present, use
them instead.
We save & restore the temporary register in addition to the VCPU pointer
register when using a KScratch register for it, as it may be used for
normal host TLB handling too.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On return from the exit handler to the host (without re-entering the
guest) we restore the saved value of the DDATA_LO register which we use
as a scratch register. However we've already restored it ready for
calling the exit handler so there is no need to do it again, so drop
that code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check for presence of MSA at uasm assembly time rather than at runtime
in the generated KVM host entry code. This optimises the guest exit path
by eliminating the MSA code entirely if not present, and eliminating the
read of Config3.MSAP and conditional branch if MSA is present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The FPU handling code on entry from guest is unnecessary if no FPU is
present, so allow it to be dropped at uasm assembly time.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dump the generated entry code with pr_debug(), similar to how it is done
in tlbex.c, so it can be more easily debugged.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the whole of locore.S (assembly to enter guest and handle
exception entry) to be generated dynamically with uasm. This is done
with minimal changes to the resulting code.
The main changes are:
- Some constants are generated by uasm using LUI+ADDIU instead of
LUI+ORI.
- Loading of lo and hi are swapped around in vcpu_run but not when
resuming the guest after an exit. Both bits of logic are now generated
by the same code.
- Register MOVEs in uasm use different ADDU operand ordering to GNU as,
putting zero register into rs instead of rt.
- The JALR.HB to call the C exit handler is switched to JALR, since the
hazard barrier would appear to be unnecessary.
This will allow further optimisation in the future to dynamically handle
the capabilities of the CPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the functions from context_tracking.h directly.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Combine the kvm_enter, kvm_reenter and kvm_out trace events into a
single kvm_transition event class to reduce duplication and bloat.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 93258604ab ("MIPS: KVM: Add guest mode switch trace events")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert MIPS KVM guest register state initialisation to use the standard
<asm/mipsregs.h> register field definitions for Config registers, and
drop the custom definitions in kvm_host.h which it was using before.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialise the guest's CP0_Config register with a few more bits of
information from the host. The BE bit should be set on big endian
machines, the VI bit should be set on machines with a virtually tagged
instruction cache, and the reported architecture revision should match
that of the host (since we won't support emulating pre-r6 instruction
encodings on r6 or vice versa).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM TLB mappings for the guest were being created with a cache coherency
attribute (CCA) of 3, which is cached incoherent. Create them instead
with the default host CCA, which should be the correct one for coherency
on SMP systems.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The comm page which is mapped into the guest kernel address space at
0x0 has the unfortunate side effect of allowing guest kernel NULL
pointer dereferences to succeed. The only constraint on this address is
that it must be within 32KiB of 0x0, so that single lw/sw instructions
(which have 16-bit signed offset fields) can be used to access it, using
the zero register as a base.
So lets move the comm page as high as possible within that constraint so
that 0x0 can be left unmapped, at least for page sizes < 32KiB.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow up to 6 KVM guest KScratch registers to be enabled and accessed
via the KVM guest register API and from the guest itself (the fallback
reading and writing of commpage registers is sufficient for KScratch
registers to work as expected).
User mode can expose the registers by setting the appropriate bits of
the guest Config4.KScrExist field. KScratch registers that aren't usable
won't be writeable via the KVM Ioctl API.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Actually provide the VCPU number when emulating the RDHWR CPUNum
register, so that it will match the CPUNum field of CP0_EBase register,
rather than always returning 0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ULRI bit in Config3 specifies whether the UserLocal register is
implemented, but it is assumed to always be set. Now that the Config
registers can be modified by userland, allow Config3.ULRI to be cleared
and check ULRI before allowing the corresponding bit to be set in
HWREna.
In fact any HWREna bits corresponding to unimplemented RDHWR registers
should read as zero and be ignored on write, so we actually prevent
other unimplemented bits being set too.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM modifies CP0_HWREna during guest execution so it can trap and
emulate RDHWR instructions, however it always restores the hardcoded
value 0x2000000F. This assumes the presence of the UserLocal register,
and the absence of any implementation dependent or future HW registers.
Fix by exporting the value that traps.c write into CP0_HWREna, and
loading from there instead of hard coding.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No preprocessor definitions are used in the handling of the registers
accessible with the RDHWR instruction, nor the corresponding bits in the
CP0 HWREna register.
Add definitions for both the register numbers (MIPS_HWR_*) and HWREna
bits (MIPS_HWRENA_*) in asm/mipsregs.h and make use of them in the
initialisation of HWREna and emulation of the RDHWR instruction.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make KVM_GET_REG_LIST list FPU & MSA registers. Specifically we list all
32 vector registers when MSA can be enabled, 32 single-precision FP
registers when FPU can be enabled, and either 16 or 32 double-precision
FP registers when FPU can be enabled depending on whether FR mode is
supported (which provides 32 doubles instead of 16 even doubles).
Note, these registers may still be inaccessible depending on the current
FP mode of the guest.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the implementation of KVM_GET_REG_LIST more dynamic so that only
the subset of registers actually available can be exposed to user mode.
This is important for VZ where some of the guest register state may not
be possible to prevent the guest from accessing, therefore the user
process may need to be aware of the state even if it doesn't understand
what the state is for.
This also allows different MIPS KVM implementations to provide different
registers to one another, by way of new num_regs(vcpu) and
copy_reg_indices(vcpu, indices) callback functions, currently just
stubbed for trap & emulate.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass all unrecognised register IDs through to the set_one_reg() and
get_one_reg() callbacks, not just select ones. This allows
implementation specific registers to be more easily added without having
to modify arch/mips/kvm/mips.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert various MIPS KVM guest instruction emulation functions to decode
instructions (and encode translations) using the union mips_instruction
and related enumerations in asm/inst.h rather than #defines and
hardcoded values.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The code in kvm_mips_dyntrans.c to write a translated guest instruction
to guest memory depending on the segment is duplicated between each of
the functions. Additionally the cache op translation functions assume
the instruction is in the KSEG0/1 segment rather than KSEG2/3, which is
generally true but isn't guaranteed.
Factor that code into a new kvm_mips_trans_replace() which handles both
KSEG0/1 and KSEG2/3.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MIPS KVM dynamic translation is meant to translate "MFC0 rt, ErrCtl"
instructions into "ADD rt, zero, zero" to zero the destination register,
however the rt register number was copied into rt of the ADD instruction
encoding, which is the 2nd source operand. This results in "ADD zero,
zero, rt" which is a no-op, so only the first execution of each such
MFC0 from ErrCtl will actually read 0.
Fix the shift to put the rt from the MFC0 encoding into the rd field of
the ADD.
Fixes: 50c8308538 ("KVM/MIPS32: Binary patching of select privileged instructions.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When trying to emulate an unrecognised load or store instruction, print
the encoding to aid debug.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If kvm_get_inst() fails to find a guest TLB mapping for the guest PC
then dump the guest TLB entries. The contents of the guest TLB is likely
to be more interesting than the host TLB entries.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Trace emulation of guest access to various registers via
MFC0/MTC0/DMFC0/DMTC0 instructions (coprocessor 0) and the RDHWR
instruction (hardware registers exposed to userland), replacing some
existing kvm_debug calls. Trace events are much more practical for this
kind of debug output.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a few trace events for entering and coming out of guest mode, as well
as re-entering it from a guest exit exception.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up the MIPS kvm_exit trace event so that the exit reasons are
specified in a trace friendly way (via __print_symbolic), and so that
the exit reasons that derive straight from Cause.ExcCode values map
directly, allowing a single trace_kvm_exit() call to replace a bunch of
individual ones.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a MIPS specific trace event for auxiliary context operations
(notably FPU and MSA). Unfortunately the generic kvm_fpu trace event
isn't flexible enough to handle the range of interesting things that can
happen with FPU and MSA context.
The type of state being operated on is traced:
- FPU: Just the FPU registers.
- MSA: Just the upper half of the MSA vector registers (low half already
loaded with FPU state).
- FPU & MSA: Full MSA vector state (includes FPU state).
As is the type of operation:
- Restore: State was enabled and restored.
- Save: State was saved and disabled.
- Enable: State was enabled (already loaded).
- Disable: State was disabled (kept loaded).
- Discard: State was discarded and disabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
[Fix remaining occurrence of "fpu_msa", change to "aux". - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename fpu_inuse and the related definitions to aux_inuse so it can be
used for lazy context management of other auxiliary processor state too,
such as VZ guest timer, watchpoints and performance counters.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like other functions, make use of a local unsigned long va, for the
virtual address of the PC. This reduces the amount of verbose casting of
the opc pointer to an unsigned long.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The handle_tlb_ld/st_miss handlers are logically equivalent and
textually almost identical, so combine their implementations into a
single kvm_trap_emul_handle_tlb_miss().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert KVM to use the MIPS_ENTRYLO_* definitions from <asm/mipsregs.h>
rather than custom definitions in kvm_host.h
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The values of the EntryLo0 and EntryLo1 registers for a TLB entry are
stored in separate members of struct kvm_mips_tlb called tlb_lo0 and
tlb_lo1 respectively. To allow future code which needs to manipulate
arbitrary EntryLo data in the TLB entry to be simpler and less
conditional, replace these members with an array of two elements.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM implements its own routine for dumping the host TLB entries, but we
already have dump_tlb_all() which does something very similar (although
it only prints out TLB entries which match the current ASID or are
global).
Make KVM use dump_tlb_all() along with dump_tlb_regs() to avoid the
duplication and inevitable bitrot, allowing TLB dumping enhancements
(e.g. for VZ and GuestIDs) to be made in a single place.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM's host TLB handling routines were using tlbw hazard barrier macros
around tlb_read(). Now that hazard barrier macros exist for tlbr, update
this case to use them.
Also fix various other unnecessary hazard barriers in this code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The host kernel's exception vector base address is currently saved in
the VCPU structure at creation time, and restored on a guest exit.
However it doesn't change and can already be easily accessed from the
'ebase' variable (arch/mips/kernel/traps.c), so drop the host_ebase
member of kvm_vcpu_arch, export the 'ebase' variable to modules and load
from there instead.
This does result in a single extra instruction (lui) on the guest exit
path, but simplifies the code a bit and removes the redundant storage of
the host exception base address.
Credit for the idea goes to Cavium's VZ KVM implementation.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function kvm_mips_handle_mapped_seg_tlb_fault() has two completely
unused pointer arguments, hpa0 and hpa1, for which all users always pass
NULL.
Drop these two arguments and update the callers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When handling TLB faults in the guest KSeg0 region, a pair of physical
addresses are read from the guest physical address map. However that
process is rather convoluted with an if/then/else statement. Simplify it
to just clear the lowest bit for the even entry and set the lowest bit
for the odd entry.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
