Allow the device tree to specify a watchdog to fallover to
the alternate boot source.
The aspeeed watchdog can set a latch directing flash chip select 0 to
chip select 1, allowing boot from an alternate media if the watchdog
is not reset in time. On the ast2400 bank 1 also goes to flash bank 1,
while on the ast2500 the chip selects are swapped.
Also clear the secondary boot bit during the machine restart operation.
Otherwise, the system will switch to the alternate boot after every
reboot, which is not desired.
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Nuvoton NPCM750 has a watchdog implemented as a single register
inside the timer peripheral.
This driver exposes that watchdog as a standard watchdog device with
coarse timeout intervals, limited by the combination of prescaler and
counter that is provided by the hardware. The calculation is taken from
the Nuvoton vendor tree.
The watchdog is left running if a bootloader had it going. The rate is
the one specified in the device tree, or the default value (obtained
from the datasheet).
There is a pre-timeout IRQ that is wired up. This timeout always occurs
1024 clocks before the timeout.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These bindings describe the watchdog IP as used by the Nuvoton NPCM750
(Poleg) BMC SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On iWave's boards iwg20d and iwg22d the only way to reboot the system is
by means of the watchdog.
This patch adds a restart handler to rwdt_ops, and also makes sure we
keep its priority to the lowest level, in order to not override other
more effective handlers.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Due to commits:
* "ARM: shmobile: Add watchdog support",
* "ARM: shmobile: rcar-gen2: Add watchdog support", and
* "soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2",
we now have everything we needed for the watchdog to work on Gen2 and
RZ/G1.
However, on early revisions of some R-Car Gen2 SoCs, and depending on SMP
configuration, the system may fail to restart on watchdog time-out, and
lock up instead.
Specifically:
- On R-Car H2 ES1.0 and M2-W ES1.0, watchdog restart fails unless
only the first CPU core is in use (using e.g. the "maxcpus=1" kernel
commandline option).
- On R-Car V2H ES1.1, watchdog restart fails unless SMP is disabled
completely (using CONFIG_SMP=n during build configuration, or using
the "nosmp" or "maxcpus=0" kernel commandline options).
This commit adds "renesas,rcar-gen2-wdt" as compatible string for R-Car
Gen2 and RZ/G1, but also prevents the system from using the watchdog
driver in cases where the system would fail to restart by blacklisting
the affected SoCs, using the minimum known working revisions (ES2.0 on R-Car
H2, and ES3.0 on M2-W), and taking the actual SMP software configuration
into account.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
[Geert: blacklisting logic]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On R-Car Gen2 and RZ/G1 the watchdog IP clock needs to be always ON,
on R-Car Gen3 we power the IP down during suspend.
This commit adds suspend/resume support, so that the watchdog counting
"pauses" during suspend on all of the SoCs compatible with this driver
and on those we are now adding support for (R-Car Gen2 and RZ/G1).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Update driver version number to reflect changes.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a few dynamic debug messages to aid in module level debug.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make whether or not the hpwdt watchdog delivers a pretimeout NMI
programable by the user.
The underlying iLO hardware is programmable as to whether or not
a pre-timeout NMI is delivered to the system before the iLO resets
the system. However, the iLO does not allow for programming the
length of time that NMI is delivered before the system is reset.
By watchdog API, in hpwdt_set_pretimeout a val == 0 disables the NMI.
When val != 0, hpwdt_set_pretimeout will enable the pretimeout NMI
provided the current timeout is greator than the HW specified
pretimeout length. Otherwise an error is returned.
In set_timeout, if the new timeout is <= an already established pretimeout,
the pretimeout is canceled. This matches the action watchdog_set_timeout
in the watchdog core would do if an hpwdt specific set_timeout
function wasn't specified.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The intent of this parameter is unclear and it sets up a
race between the reset of the system by ASR and crashdump.
The length of time between receipt of the pretimeout NMI
and the ASR reset of the system is fixed by hardware.
Turning the parameter off doesn't necessairly prevent a crash dump.
Also, having the ASR reset occur while the system is crash dumping
doesn't imply that the dump was hung given the short duration
between the NMI and the reset.
This parameter is not a substitute for having a architected watchdog
crashdump hang detection paridigm.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Modify prior change to not claim an NMI unless originated
from iLO to apply only to iLO5 and later going forward.
This restores hpwdt traditional behavior of calling panic
if the NMI is NMI_IO_CHECK, NMI_SERR, or NMI_UNKNOWN for
legacy hardware.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Include the nmistat in the nmi_panic message to give support
an indication why the NMI was called (e.g. a timeout or generate
nmi button.)
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If devm_reset_control_get_exclusive() fails, asm9260_wdt_probe()
returns immediately. But clks has been already enabled at that point,
so it is required to disable them or to move the code around.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Licence text is specifying "GPLv2" but the MODULE_LICENSE is set to "GPLv2
or later".
See include/linux/module.h:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
When on it, add SPDX identifier tag.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if
no parameter nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if
no parameter nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will preserve wdd->timeout value if no parameter
nor timeout-secs dt property is set.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also
let us to set timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog_init_timeout() will allways pick timeout_param since it
defaults to a valid timeout.
Following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt to make use of
the parameter logic.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
By following best practice described in
Documentation/watchdog/watchdog-kernel-api.txt, it also let us to set
timout-sec property in devicetree.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Gen8 and prior Proliant systems supported the "CRU" interface
to firmware. This interfaces allows linux to "call back" into firmware
to source the cause of an NMI. This feature isn't fully utilized
as the actual source of the NMI isn't printed, the driver only
indicates that the source couldn't be determined when the call
fails.
With the advent of Gen9, iCRU replaces the CRU. The call back
feature is no longer available in firmware. To be compatible and
not attempt to call back into firmware on system not supporting CRU,
the SMBIOS table is consulted to determine if it is safe to
make the call back or not.
This results in about half of the driver code being devoted
to either making CRU calls or determing if it is safe to make
CRU calls. As noted, the driver isn't really using the results of
the CRU calls.
Furthermore, as a consequence of the Spectre security issue, the
BIOS/EFI calls are being wrapped into Spectre-disabling section.
Removing the call back in hpwdt_pretimeout assists in this effort.
As the CRU sourcing of the NMI isn't required for handling the
NMI and there are security concerns with making the call back, remove
the legacy (pre Gen9) NMI sourcing and the DMI code to determine if
the system had the CRU interface.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to SBSA spec v3.1 section 5.3:
All registers are 32 bits in size and should be accessed using
32-bit reads and writes. If an access size other than 32 bits
is used then the results are IMPLEMENTATION DEFINED.
[...]
The Generic Watchdog is little-endian
The current code uses readq to read the watchdog compare register
which does a 64-bit access. This fails on ThunderX2 which does not
implement 64-bit access to this register.
Fix this by using lo_hi_readq() that does two 32-bit reads.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Watchdog close is "expected" when any byte is 'V' not just the last one.
Writing "V" to the device fails because the last byte is the end of string.
$ echo V > /dev/watchdog
f71808e_wdt: Unexpected close, not stopping watchdog!
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
isp5100_tco.c uses watchdog core functions (from watchdog_core.c) and, when
compiled without CONFIG_WATCHDOG_CORE being set, it produces the
following build error:
ERROR: "devm_watchdog_register_device" [drivers/watchdog/sp5100_tco.ko] undefined!
ERROR: "watchdog_init_timeout" [drivers/watchdog/sp5100_tco.ko] undefined!
Fix this by selecting CONFIG_WATCHDOG_CORE.
Fixes: 7cd9d5fff7 ("watchdog: sp5100_tco: Convert to use watchdog subsystem")
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
xen_wdt uses watchdog core functions (from watchdog_core.c) and, when
compiled without CONFIG_WATCHDOG_CORE being set, it produces the
following build error:
ERROR: "devm_watchdog_register_device" [drivers/watchdog/xen_wdt.ko] undefined!
ERROR: "watchdog_init_timeout" [drivers/watchdog/xen_wdt.ko] undefined!
Fix this by selecting CONFIG_WATCHDOG_CORE when CONFIG_XEN_WDT is set.
Fixes: 18cffd68e0 ("watchdog: xen_wdt: use the watchdog subsystem")
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
i6300esb uses fuctions defined in watchdog_core.c, and when
CONFIG_WATCHDOG_CORE is not set we have this build error:
drivers/watchdog/i6300esb.o: In function `esb_remove':
i6300esb.c:(.text+0xcc): undefined reference to `watchdog_unregister_device'
drivers/watchdog/i6300esb.o: In function `esb_probe':
i6300esb.c:(.text+0x2a1): undefined reference to `watchdog_init_timeout'
i6300esb.c:(.text+0x388): undefined reference to `watchdog_register_device'
make: *** [Makefile:1029: vmlinux] Error 1
Fix this by selecting CONFIG_WATCHDOG_CORE when I6300ESB_WDT is set.
Fixes: 7af4ac8772 ("watchdog: i6300esb: use the watchdog subsystem")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We can build this driver with or without NVMEM, but not built-in
when NVMEM is a loadable module:
drivers/watchdog/rave-sp-wdt.o: In function `rave_sp_wdt_probe':
rave-sp-wdt.c:(.text+0x27c): undefined reference to `nvmem_cell_get'
rave-sp-wdt.c:(.text+0x290): undefined reference to `nvmem_cell_read'
rave-sp-wdt.c:(.text+0x2c4): undefined reference to `nvmem_cell_put'
This adds a Kconfig dependency to enforce that.
Fixes: c3bb333457 ("watchdog: Add RAVE SP watchdog driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull x86 Kconfig fixes from Thomas Gleixner:
"Three patchlets to correct HIGHMEM64G and CMPXCHG64 dependencies in
Kconfig when CPU selections are explicitely set to M586 or M686"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Pull perf updates from Thomas Gleixner:
"Perf tool updates and kprobe fixes:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf
top' using it, making it bearable to use it in large core count
systems such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the
syscall table id -> string tables used by 'perf trace' (Hendrik
Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William
Cohen)
- Improve error handling and error propagation of ftrace based
kprobes so failures when installing kprobes are not silently
ignored and create disfunctional tracepoints"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
kprobes: Propagate error from disarm_kprobe_ftrace()
kprobes: Propagate error from arm_kprobe_ftrace()
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
perf s390: Rework system call table creation by using syscall.tbl
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
perf data: Document missing --force option
perf tools: Substitute yet another strtoull()
perf top: Check the latency of perf_top__mmap_read()
perf top: Switch default mode to overwrite mode
perf top: Remove lost events checking
perf hists browser: Add parameter to disable lost event warning
perf top: Add overwrite fall back
perf evsel: Expose the perf_missing_features struct
perf top: Check per-event overwrite term
perf mmap: Discard legacy interface for mmap read
perf test: Update mmap read functions for backward-ring-buffer test
perf mmap: Introduce perf_mmap__read_event()
perf mmap: Introduce perf_mmap__read_done()
...
Pull irq updates from Thomas Gleixner:
"A small set of updates mostly for irq chip drivers:
- MIPS GIC fix for spurious, masked interrupts
- fix for a subtle IPI bug in GICv3
- do not probe GICv3 ITSs that are marked as disabled
- multi-MSI support for GICv2m
- various small cleanups"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Re-use DEFINE_SHOW_ATTRIBUTE() macro
irqchip/bcm: Remove hashed address printing
irqchip/gic-v2m: Add PCI Multi-MSI support
irqchip/gic-v3: Ignore disabled ITS nodes
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
irqchip/gic-v3: Change pr_debug message to pr_devel
irqchip/mips-gic: Avoid spuriously handling masked interrupts
Pull core fix from Thomas Gleixner:
"A small fix which adds the missing for_each_cpu_wrap() stub for the UP
case to avoid build failures"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpumask: Make for_each_cpu_wrap() available on UP as well
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n5RP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180217' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes all over the map for nvme.
From various folks.
- Classic polling fix, that avoids a latency issue where we still end
up waiting for an interrupt in some cases. From Nitesh Shetty.
- Comment typo fix from Minwoo Im.
* tag 'for-linus-20180217' of git://git.kernel.dk/linux-block:
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
blk: optimization for classic polling
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+wYZ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
* tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: bcm2835: Don't overwrite max frequency unconditionally
Revert "mmc: meson-gx: include tx phase in the tuning process"
* Use the appropriate OOB layout in the VF610 driver
-----BEGIN PGP SIGNATURE-----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=MaSC
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- add missing dependency to NAND_MARVELL Kconfig entry
- use the appropriate OOB layout in the VF610 driver
* tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
mtd: nand: vf610: set correct ooblayout
The main attraction is a fix for a bug in the new drmem code, which was causing
an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as well as a
few other minor fixes.
Thanks to:
Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black, Nathan Fontenot,
Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----
iQIwBAABCAAaBQJah/esExxtcGVAZWxsZXJtYW4uaWQuYXUACgkQUevqPMjhpYCi
KA/+IaDlvxKezRBNQnj6GElBrgfUzICH6MtG6qo+rCKsTMgbAiZJkk3vz/JgqKY/
EusTNCwcqLaPBDgwoSmbazdtnj7YOwBGdIQOq+rC/qeSV0/gpdo02dPUWaMMOE/x
nj+zASrOsv/o9XWX4XmJeuYWhW/8a/nWXKa+oLt3g/5pIHHP5TXTzMHvHH0Rn23D
1ejwDHDwMNL3p2jHlcf+v1DDol51/Kaa8e8KwJJMf00HVfFVXtdnH7do6I1qBeC0
t7PLDeWnpyY+3M1fNJ303EXIqc9DArUCn6tdhy6om96rGvBddORFuRkS4kkXbx76
pnTRPWnPa9aeC2rU+C84sJDQJgeBCpMYOvw96Yr1SxFhE9z0T+9YYTnZxiB7GISK
5BAf3EzE9dc0RtStrfTKnvcuz2OffPq2VZi3sqjiHFDit2TsF+i7ZkX/CR9UAmaH
HPk4Fbi/IzlSfx/RffrOXYrpsTNcUmzvA/Tj83qGhM30LCMQ24o84eGTZN36a/eg
Z+7/MZawtNElsNNpJz6MYtvEQkHZyrTUS+9iyqRwLXCIy/JIHZYwb4aRtu41SET8
lWwuaLjfwdpVPCeEkiNQwCswtppt4j2XS8Ggqef9GkqElsk6JKyxuZWTv2hRfJUK
DTQvPV4PIhvhrB6qvT11qOm5yDSSV9f6yaLJ5dm3BiXulF0=
=8QPF
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main attraction is a fix for a bug in the new drmem code, which
was causing an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as
well as a few other minor fixes.
Thanks to: Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black,
Nathan Fontenot, Nicholas Piggin"
* tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
powerpc/pseries: Add empty update_numa_cpu_lookup_table() for NUMA=n
powerpc/powernv: IMC fix out of bounds memory access at shutdown
powerpc/xive: Use hw CPU ids when configuring the CPU queues
powerpc: Expose TSCR via sysfs only on powernv
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the recursive
page table walking to take a significant time
- Fix some sparse warnings
-----BEGIN PGP SIGNATURE-----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=O6of
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"The bulk of this is the pte accessors annotation to READ/WRITE_ONCE
(we tried to avoid pushing this during the merge window to avoid
conflicts)
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the
recursive page table walking to take a significant time
- Fix some sparse warnings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cputype: Silence Sparse warnings
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
arm64: proc: Set PTE_NG for table entries to avoid traversing them twice
arm64: Add missing Falkor part number for branch predictor hardening
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJah+tbAAoJELDendYovxMvHIYH/38IC3Nd3IWTVsLvHXUCxFrn
fNPKgSyC5/igLbmwjPQ+kbr7bha6Vi3uZwmovoC/9i03gYfzmuuMhhOvOVByYHXg
HHC+kqegB7tZ2GFeR2hrIba4UxBz4ZC0R5+qQYHZMx5dRt0/Llby663mkcK7WEWr
Na8jT32AbIOiCKWHgsmTC7h2ZiSXeY+WVj1B3Re7ovLHMTYoMDQhVi5I7w34bcch
bgTLx4TokC8Z3kCNotPAwrL0rQggEJ+PR91j2mL52uEWv80Q4hgR+QIFtEwiYXmG
jDbx4Y+jQUAu4+r6/2z4S/gFTV93lB+dWbXYuHoFv5Mv1A+Ve7Al744RvrNh3gM=
=UVdB
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fixes for the Xen pvcalls frontend driver
- fix for booting Xen pv domains
- fix for the xenbus driver user interface
* tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: wait for other operations to return when release passive sockets
pvcalls-front: introduce a per sock_mapping refcount
x86/xen: Calculate __max_logical_packages on PV domains
xenbus: track caller request id
Passive sockets can have ongoing operations on them, specifically, we
have two wait_event_interruptable calls in pvcalls_front_accept.
Add two wake_up calls in pvcalls_front_release, then wait for the
potential waiters to return and release the sock_mapping refcount.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Marcus Folkesson