In case of error, the function devm_clk_get() returns ERR_PTR()
and not returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In case of error, the function devm_clk_get() returns ERR_PTR()
and not returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When transmitting a message and waiting for a reply it would be good
to know the time between when the message was transmitted and when
the reply arrived. With only one timestamp field it was set to when
the reply arrived and the original transmit time was overwritten.
Just taking the timestamp in userspace right before CEC_TRANSMIT is
called is not reliable, since the actual transmit can be delayed if
the CEC bus is busy. Only the driver can fill this in accurately.
So split up the ts field into an rx_ts and a tx_ts. Also move the
status fields to after the 'reply' field: they were placed in a
strange position and make much more sense when grouped with the
other status-related fields.
This patch also makes sure that the timestamp is taken as soon as
possible.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check (and warn) if the msg->len is too long or if it is 0.
Should never happen, but just in case...
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DW2102 DVB-S/S2 driver uses the info() logging function from
dvb-usb.h. This function already appends a newline to the provided log
message, causing the dmesg output from DW2102 to include blank lines.
Fix this by removing the newline in the calls to info().
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We have assigned memory while requesting the firmware but if the sanity
check fails then we are not releasing the firmware.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Explain what needs to be done to move this driver out of staging.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add entry for the pulse8-cec driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This supports the Pulse-Eight USB-CEC Adapter.
It has been tested with firmware versions 4 and 5, but it should
hopefully work fine with older firmwares as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is for the new pulse8-cec staging driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the device is in monitor mode, then you should always be able to
call CEC_RECEIVE, even it the device is unconfigured.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support fo the Hauppauge WinTV quadHD DVB version.
IR support has not been provided, all 4 tuners, demodulators etc are working.
Further documentation can be found on Linux TV wiki.
Signed-off-by: Stephen Backway <stev391@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC USB dongles can be unplugged at any time, and at that point they will
be unregistered. Make sure that any attempt afterwards to set the physical
or logical addresses will be ignored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Correctly set the h/vsync polarities instead of keeping to the
default (positive).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This field should be zeroed. Both for s_dv_timings and for enum_dv_timings.
In fact, for the latter anything after the pad field can be zeroed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These platform_data fields are no longer needed, drop them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The adv7604/adv7842 drivers now handle that register setting themselves
and need no input from platform data anymore.
This was a left-over from the time that the pixelport output format was
decided by the platform data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a number of bugs that appeared when support for mediabus formats was
added:
- Support for V4L2_DV_RGB_RANGE_FULL/LIMITED should only be enabled
for HDMI RGB formats, not for YCbCr formats. Since, as the name
says, this setting is for RGB only. So read the InfoFrame to check
the format.
- the quantization range for the pixelport depends on whether the
mediabus code is RGB or not: if it is RGB, then produce full range
RGB values, otherwise produce limited range YCbCr values.
This means that the op_656_range and alt_data_sat fields of the
platform data are no longer used and these will be removed in a
following patch.
- when setting up a new format the RGB quantization range settings
were never updated. Do so, since this depends on the format.
- fix the log_status output which was confusing and incorrect.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 1fb69bfd29 (adv7511: improve
colorspace handling) introduced a number of bugs, specifically with
regards to YCbCr output and quantization range handling:
- if the output is not RGB, then disable the full-to-limited range
CSC matrix since that is meant for RGB formats. YCbCr formats are
always limited range, so there is nothing to convert. (OK, full
range YCbCr is possible, but we don't support that right now).
- the mediabus code that was passed to adv7511_set_fmt was always cleared
by the memset in adv7511_fill_format. This made it effectively impossible
to select YCbCr output.
- adv7511_set_fmt never updated the rgb quantization range.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IT Content bit has nothing to do with CE vs IT timings.
Delete this code. This will also fix a bug where this could
override the 'content type' control, which is actually the
correct place to set/clear the ITC bit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix two warnings:
af9033.c: In function 'af9033_read_status':
af9033.c:883:25: warning: 'snr_lut' may be used uninitialized in this function [-Wmaybe-uninitialized]
const struct val_snr *snr_lut;
^
af9033.c:952:25: warning: 'tmp' may be used uninitialized in this function [-Wmaybe-uninitialized]
c->cnr.stat[0].svalue = tmp;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In practice, devices sometimes return frames larger than current buffer
size, leading to failure in solo_send_desc().
It is not clear which minimal increase in buffer size would be enough,
so this patch doubles it, this should be safely assumed as sufficient.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When disconnecting the usbtv device, the sound card is unregistered
from ALSA and the snd member of the usbtv struct is set to NULL. If
the usbtv snd_trigger work is running, this can cause a race condition
where the kernel will attempt to access free'd resources, shown in
[1].
This patch fixes the disconnection code by cancelling any snd_trigger
work before unregistering the sound card from ALSA and checking that
the snd member still exists in the work function.
[1]:
usb 3-1.2: USB disconnect, device number 6
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff81093850>] process_one_work+0x30/0x480
PGD 405bbf067 PUD 405bbe067 PMD 0
Call Trace:
[<ffffffff81093ce8>] worker_thread+0x48/0x4e0
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81099998>] kthread+0xd8/0xf0
[<ffffffff815c73c2>] ret_from_fork+0x22/0x40
[<ffffffff810998c0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 0f3dac5c1a38e610 ]---
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Tested-by: Peter Sutton <foxxy@foxdogstudios.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vivid driver didn't set the V4L2_CAP_TIMEPERFRAME flag in s_parm for the
non-webcam inputs. This caused a v4l2-compliance fail.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch fix sparse warning when running with parameters:
C=2 CF="-D__CHECK_ENDIAN__"
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: PoChun Lin <pochun.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_drv.c:433:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These are no longer used (finally!), so remove them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Nobody is using these ops anymore, so remove these callbacks from
the subdev drivers that still have them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These ops are deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These ops are deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These ops are deprecated and should not be used anymore (and in fact
they are not used at all).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These callbacks are no longer used since the davinci drivers use the
control framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old control code with the control framework.
This is one of the few remaining drivers that was not using this
framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Converts the dtt200u DVB USB driver over to the rc-core
infrastructure for its handling of IR remotes. This device can receive
generic NEC / NEC Extended signals and the switch to the newer core
enables the easy use of tools such as ir-keytable to modify the active
key map.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix RC5 decoding with Fintek CIR chipset
Commit e87b540be2 tightened up the RC5
decoding by adding a check for trailing silence to ensure a valid RC5
command had been received. Unfortunately the trailer length checked was
10 units and the Fintek CIR device does not want to provide details of a
space longer than 6350us. This meant that RC5 remotes working on a
Fintek setup on 3.16 failed on 3.17 and later. Fix this by shortening
the trailer check to 6 units (allowing for a previous space in the
received remote command).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117221
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Cc: stable@vger.kernel.org
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement memory barriers according to Documentation/circular-buffers.txt:
- use smp_store_release() to update ringbuffer read/write pointers
- use smp_load_acquire() to load write pointer on reader side
- use ACCESS_ONCE() to load read pointer on writer side
This fixes data stream corruptions observed e.g. on an ARM Cortex-A9
quad core system with different types (PCI, USB) of DVB tuners.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in updating parameters for
transfers. It has a single work item(&sd->work) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mtk-vcodec/mtk_vcodec_enc.c: In function 'mtk_venc_worker':
mtk-vcodec/mtk_vcodec_enc.c:1030:43: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type 'size_t {aka unsigned int}' [-Wformat=]
mtk-vcodec/mtk_vcodec_enc.c:1030:43: warning: format '%lx' expects argument of type 'long unsigned int', but argument 10 has type 'size_t {aka unsigned int}' [-Wformat=]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current code will expose a zero value if one of the stats is
not available, but this is not what userspace expects. Instead,
if something goes wrong on providing some stats, it should be
changing the scale to FE_SCALE_NOT_AVAILABLE.
So, change the logic to do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
