Protect against invalid phy entries in the eeprom.
Extend eeprom access timeout.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The doorbell writes may be seen out of order by the firmware if they
are in WC memory since the tx spin(un)lock does not flush WC writes.
Hence if the "stop" is written on a different CPU than the "go", it
is possible that the stop will arrive after the go unless we add an
explicit memory barrier (and mmiowb() is not enough).
It fixes transmit hangs in multi tx queue mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a different
CCK power setting code as compared with the Linux driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Piter Punk <piterpk@terra.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keeping all the orinoco drivers in a common directory will make
maintenance easier.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a debugfs file (ieee80211/phy#/hwsim/ps) that can be
used to force a simulated radio into power save mode. Following values
can be written into this file to change PS mode:
0 = power save disabled (constantly awake)
1 = power save enabled (drop all frames; do not send PS-Poll)
2 = power save enabled (send PS-Poll frames automatically to receive
buffered unicast frames); not yet fully implemented
3 = manual PS-Poll trigger (send a single PS-Poll frame)
Two different behavior for power save mode processing can be tested:
- move between modes 1 and 0 (i.e., receive all buffered frames at a
time)
- move to mode 1 and use manual PS-Poll frames (write 3 to the 'ps'
debugfs file) to fetch power save buffered frames one at a time
Mode 2 (automatic PS-Poll) does not yet parse Beacon frames, but
eventually, it should take a look at TIM IE and send PS-Poll if a
traffic bit is set for our AID.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible to trigger a kernel panic because beacon_timer may not
have been deleted in all cases when the kernel module was removed while
hostapd was still running.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide detailed information on TX queue parameter changes to make it
easier to debug mac80211 functionality.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide detailed information on BSS configuration changes to make it
easier to debug mac80211 functionality.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new mechanism for allocing space for control frames,
didn't "zero" out the payload data... However I haven't
heard of any hiccups so far...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix rate scaling initialization. Rate scaling
was initialized always with B antenna.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch change the name of the double inclusion protection in
iwl-commands.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames functions that are generic in iwl-agn and had a iwl4965
prefix.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 supports multiple virtual interfaces for a single device. For
example, a managed interface (wlan0) and a monitor interface (mon0) can
exist at the same time. Thus priv->iw_mode is not sufficient to track
the wireless mode any more. The patch redefines priv->iw_mode as the
first interface mode (the same as priv->vif->type if priv->vif != NULL).
If another monitor type interface is created later, we don't change
priv->iw_mode into monitor. This way, the original interface still
works. The patch also requests mac80211 to do reassociation after we
change the Rx filter flags.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes 4965 prefix from comments and one function
in iwl-agn-rs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up FH bits and adds missing register values
that will be used later in TX initialization rewrite
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements proper short slot handling and adds code to
program the hardware for the correct response rates derived
from the basic rate set for the current BSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath9k/xmit.c: In function ‘ath_tx_start’:
drivers/net/wireless/ath9k/xmit.c:1858: warning: ‘tid’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a 10 msec
delay after the call to set a new channel, but not before.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each of the primary write routines, rtl8187_write_phy(),
rtl8225_write_bitbang(), and rtl8225_write_8051() all conclude with an
msleep() command. Testing shows that these are not needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routine rtl8225_write() calls either rtl8225_write_bitbang() or
rtl8225_write_8051(), both of which end with an msleep() command. As a
result, a rtl8225_write() immediately followed by an msleep() is not needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routine rtl8225_write_phy_cck() calls rtl8225_write_phy(), which concludes
with a sleep of 1 msec; therefore a call to rtl8225_write_phy_cck()
immediately followed by an msleep(1) is not needed.
Signed-off-by: Larry Finger <Larry.Finger@larry.finger>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routine rtl8225_write_phy_ofdm() calls rtl8225_write_phy(), which concludes
with a sleep of 1 msec; therefore a call to rtl8225_write_phy_ofdm()
immediately followed by an msleep(1) is not needed.
Signed-off-by: Larry Finger <Larry.Finger@larry.finger>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtl8187 driver contains 3 sleep statements that are longer than
a second. Testing has shown no bad effects when they are removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All operating modes which require beaconing should
depend on the availability of beacon entries from
the hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can safely remove ieee80211_bss_conf from rt2x00_intf,
it is provided by mac80211 in ieee80211_vif as well.
(rt2x00_intf is the drv_priv field of ieee80211_vif).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer parts have slots at entry+64 for michael mic and can do WPA-TKIP
in hardware. The open-sourced Atheros HAL has code for accessing this
portion so now we know how where to put the key material.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change re-enables hardware encryption for ath5k after setting up
mac80211 to handle the initialization vectors which happens to make it
work. Add a module param (nohwcrypt) to optionally turn it off.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has RX A-MPDU reordering support.
Use that and remove redundant RX processing within the driver.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing an interface down/up leaves the old HT assoc
information, clear it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing mac80211's internal state machine is wrong.
Will add resumption of a TID in a later patch.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
config_interface() was the wrong place to enable interrupts
when bringing up an interface, move it to ath_open().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TSF is already reset properly via mac80211's callback.
Resetting it in config_interface() is not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify attach and detach routines by consolidating
the stop and suspend functions.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split hw.c into more manageable files:
ani.c
calib.c
eeprom.c
mac.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the internal VAP management routines
and embed ath_vap in mac80211's driver private area
provided in ieee80211_vif.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, random indentation and whitespace cleanup.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ath_buf instance associated with each tx frame
directly and remove all redundant information in ath_tx_control.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Start removing the internal node list in ath9k, in preparation
for using mac80211's STA list.
Remove lists, locks, routines, flags, functions managing nodes in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Be sure we clear out both the mic (if applicable) and
the encryption key type.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* In set_opmode don't handle antenna settings and preserve other STA_ID1 settings
(shouldn't matter because we call it during reset but it makes things cleaner)
Also set properly AP/ADHOC indicator flag on CFG while setting AP/ADHOC modes
and always enable key search mode.
* Properly set BSSID Mask during reset (cache it and reuse it durring set_associd)
* Update beacon_init to flush pending BMISS interrupts and handle setting of adhoc
beacon ATIM policy flag for ad-hoc mode. Also set TSF to 0 to start TSF increment
on AP mode. We need to handle sleep timers for AR5212 there + add support for PCF.
* Properly clean MIC key from keytable when TKIP is used (Bob is working on set_key
function etc so i leave it for now).
Tested on AR5212 (Hainan) and AR5413 and works fine
v2 Set PISR on AR5211+ and ISR on AR5210, got to sleep more ;-)
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert all the drivers using net/ieee80211.h to use linux/ieee80211.h.
Contains a bugfix in libertas where the SSID parsing could overrun the
buffer when the AP sends invalid information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Dan Williams <dcbw@redhat.com> [airo, libertas]
Acked-by: Pavel Roskin <proski@gnu.org> [orinoco]
Acked-by: David Kilroy <kilroyd@googlemail.com> [orinoco]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I added this comment myself, but it's clearly wrong. I had meant
to place it in iwl_mac_add_interface, which at the time didn't
honour the MAC address setting, but it does now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since adm8211 currently doesn't implement IBSS mode anyway,
it can't be using the SSID. And if/when it does implement
IBSS mode, we'll have to see how to make it beacon anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSID programmed into the device is used by the ucode only
to reply to probe requests, a functionality we disable anyway
because it doesn't fit with the mac80211/hostapd programming
model. Therefore, it isn't useful to program the SSID into
device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the essid stuff is unused, so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an undirected scan is requested and iwlwifi is not associated but
the user has set an SSID (and maybe was associated with that network at
some point) then iwlwifi will assume the user wanted to scan for this
SSID which seems wrong. Remove this code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Was wondering about this code since supposedly the firmware will
add the SSID element. Turns out it's dead, so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added .set_frag_threshold I didn't realise it was already
there which now generated a sparse warning. Therefore, remove
the .set_frag_threshold NULL initialiser, and while at it all the
other useless ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/p54/p54common.c: In function ‘p54_tx’:
drivers/net/wireless/p54/p54common.c:1058: warning: ‘tim_len’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch finally adds all necessary code to test Ad-hoc & AP mode with p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
stlc45xx's specs finally brought some light what all the 4 extra queues for.
now CAB data and managment frames have their own queue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports more useful features to p54
- PDR definitions for the synth chips & regulatory domain.
- honour IEEE80211_TX_CTL_ASSIGN_SEQ flag, if it's set.
- adds some lost mutex_lock & mutex_unlock.
- replace two more "magic values" that sneaked past.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes thought it would have been a good idea to change the firmware names.
Note: we still have fallbacks in case our users don't want to "break their running system",
but we won't advertise them with MODULE_FIRMWARE.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.
Different to readonly reference of netdev->priv, in this driver, netdev->priv
was changed. I use netdev->ml_priv to replace netdev->priv.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
But do it carefully so we register the loopback device after
we clear dev_boot_phase.
Signed-off-by: Eric W. Biederman <ebiederm@maxwell.aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yup, this appears to be the problem, thanks. I think &hso_net->net->dev
is more intuitive for the error message, so I've used that. I've also
added missing line endings on the error messages and set our local
rfkill structure element to NULL on failure so we don't try to call
rfkill_unregister on driver removal if we failed to register at all.
The patch below Works For Me (TM); the device is detected fine, can be
removed without problems and connects ok. I'll have a prod at why the
rfkill stuff isn't working next, but I believe this cleanup of the error
handling is appropriate no matter what the issue with registration is.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tried to deactivate rx ring that wasn't activated,
used wrong index.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Write interrupt ack bit in fjn_interrupt for lan and modem to work
simultaneously.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
This patch fixes iwl3945 deadlock during suspend by moving notify_mac out
of iwl3945 mutex. This is a portion of the same fix for iwlwifi by Tomas.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures we clear any scan status bit when
an error occurs while sending the scan command. It is
the implementation of patch:
"iwlwifi: clear scanning bits upon failure"
for iwl3945.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_rx_status fields rs_antenna and rs_more are u8s, but we
were setting them with bitwise ANDs of 32-bit values.
As a consequence, jumbo frames would not be discarded as intended.
Then, because the hw rate value of such frames is zero, and, since
"ath5k: rates cleanup", we do not fall back to the basic rate, such
packets would trigger the following WARN_ON:
------------[ cut here ]------------
WARNING: at net/mac80211/rx.c:2192 __ieee80211_rx+0x4d/0x57e [mac80211]()
Modules linked in: ath5k af_packet sha256_generic aes_i586 aes_generic cbc loop i915 drm binfmt_misc acpi_cpufreq fan container nls_utf8 hfsplus dm_crypt dm_mod kvm_intel kvm fuse sbp2 snd_hda_intel snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy snd_seq_oss arc4 joydev hid_apple ecb snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device usbhid appletouch mac80211 sky2 snd ehci_hcd ohci1394 bitrev crc32 sr_mod cdrom rtc sg uhci_hcd snd_page_alloc cfg80211 ieee1394 thermal ac battery processor button evdev unix [last unloaded: ath5k]
Pid: 0, comm: swapper Tainted: G W 2.6.28-rc2-wl #14
Call Trace:
[<c0123d1e>] warn_on_slowpath+0x41/0x5b
[<c012005d>] ? sched_debug_show+0x31e/0x9c6
[<c012489f>] ? vprintk+0x369/0x389
[<c0309539>] ? _spin_unlock_irqrestore+0x54/0x58
[<c011cd8f>] ? try_to_wake_up+0x14f/0x15a
[<f81918cb>] __ieee80211_rx+0x4d/0x57e [mac80211]
[<f828872a>] ath5k_tasklet_rx+0x5a1/0x5e4 [ath5k]
[<c013b9cd>] ? clockevents_program_event+0xd4/0xe3
[<c01283a9>] tasklet_action+0x94/0xfd
[<c0127d19>] __do_softirq+0x8c/0x13e
[<c0127e04>] do_softirq+0x39/0x55
[<c0128082>] irq_exit+0x46/0x85
[<c010576c>] do_IRQ+0x9a/0xb2
[<c010461c>] common_interrupt+0x28/0x30
[<f80e934a>] ? acpi_idle_enter_bm+0x2ad/0x31b [processor]
[<c02976bf>] cpuidle_idle_call+0x65/0x9a
[<c010262c>] cpu_idle+0x76/0xa6
[<c02fb402>] rest_init+0x62/0x64
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
07fa/1196
Bewan BWIFI-USB54AR: Tested by night1308, this device is a ZD1211B with
an AL2230S radio.
0ace/b215
HP 802.11abg: Tested by Robert Philippe
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tasklet_handler -> __ieee80211_rx ->
__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
iwl_scan_cancel_timeout -> msleep
Ooops!
Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch removes some trailing whitespaces and spaces before tabs.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The TX watchdog should trigger a reset, but a temperature/power alarm
should not as this is unlikely to solve the problem.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash. Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.
Add a comment on the partitioning.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch implements alternative aggregator selection policies
for 802.3ad. The existing policy, now termed "stable," selects the active
aggregator by greatest bandwidth, and only reselects a new aggregator
if the active aggregator is entirely disabled (no more ports or all ports
down).
This patch adds two new policies: bandwidth and count, selecting
the active aggregator by total bandwidth (like the stable policy) or by
the number of ports in the aggregator, respectively. These two policies
also differ from the stable policy in that they will reselect the active
aggregator when availability-related changes occur in the bond (e.g.,
link state change).
This permits "gang failover" within 802.3ad, allowing redundant
aggregators along parallel paths to always maintain the "best" aggregator
as the active aggregator (rather than having to wait for the active to
entirely fail).
This patch also updates the driver version to 3.5.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current ALB function that processes incoming ARPs
does not handle traffic for VLANs configured above bonding. This causes
traffic on those VLANs to all be assigned the same slave. This patch
corrects that misbehavior by locating the bonding interface nested below
the VLAN interface.
Bug reported by Sven Anders <anders@anduras.de>, who also
tested an earlier version of this patch and confirmed that it resolved
the problem.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I was recently hunting a bug that occurred in network namespace
cleanup. In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present. Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.
Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init(). This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix
drivers/net/mlx4/profile.c:55: warning: 'res_name' defined but not used
by making mlx4_dbg() always use all of its parameters, regardless of
whether CONFIG_MLX4_DEBUG is set or not.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.
This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version to 3.95.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the expansion register access routines a little more
formal. They will be used by the following bcm50610 support patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds flow control support to Broadcom phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines support for the 5785 device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines the phylib support in the tg3 driver. The patch does
the following things :
* Rename tg3_mdio_config() to tg3_mdio_config_5785(). The 5785 will be
the only device that will use it so the name might as well reflect
that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
MAC <=> PHY interface.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows WOL to be enabled for Broadcom phys under phylib
control. The only exception is the AC131, which has a completely
different register set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver. The patch was understandably conservative, so this patch
elaborates on that work.
The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL. The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.
The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled. The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, phylib reports appear with a eth%d prefix. Move the line
after register_netdev() and place it alongside the other informative
messages. Update nearby informative messages accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled. Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag. It only
used twice in non-fast paths. This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the __tg3_set_mac_addr() function earlier in the file
listing, to avoid a function prototype, and calls the function to
restore the LAA after a driver unload chip reset. With this code in
place, the administrator can wake the machine using the LAA.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.
When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames. Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver. The first hunk of this patch preserves this setting.
The second hunk of this patch wipes out the driver present signature of
the APE memory space. By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the existing APE register mapping code with a call
to pci_ioremap_bar(). The code that maps the main device register space
did not undergo a similar change because the information derived from
the pci_resource_start() and pci_resource_len() is still used to
populate the (optional) mem_start and mem_end netdevice members.
Replace hardcoded constants where appropriate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 5761S chip variants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.
If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again. This would lead to occasional SMI access timeouts
when the system would be under heavy load.
The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts 51ac3beffd ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.
The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.
Based upon a build failure report from Manuel Lauss.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
dev_kfree_skb should not be called with irqs disabled, use dev_kfree_skb_irq
instead. The warning caused looks like this:
======================================================
[ INFO: hard-safe -> hard-unsafe lock order detected ]
2.6.28-rc1 #273
------------------------------------------------------
swapper/0 [HC0[0]:SC1[2]:HE0:SE0] is trying to acquire:
(clock-AF_INET){-..+}, at: [<4015c17c>] _sock_def_write_space+0x28/0xd8
and this task is already holding:
(&lp->lock){++..}, at: [<4013f230>] _smc911x_hard_start_xmit+0x30/0x4b8
which would create a new lock dependency:
(&lp->lock){++..} -> (clock-AF_INET){-..+}
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The smc_drv_probe() is the platform_driver probe function and it is only
called during init. Further, it calls smc_probe() which is marked as __init
already.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This eliminates the following often-generated warning from my 64 bit
Opteron SMP test stand:
eth0: too many iterations (6) in nv_nic_irq
According to the web, the problem is that the forcedeth driver has a
too-low value for max_interrupt_work. Grepping the kernel I see that
forcedeth has the second lowest value of all ethernet drivers (ie, 6).
Most are in the 20-40 range. So this patch increases this a bit, from 6
to 15 (at 15 forcedeth becomes the driver with third-lowest
max_interrupt_work value).
My test stand, which used to print out the above warnings repetitively
whenever it was under heavy net load, no longer does so.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do some cleanup on timer usage in this driver:
* Use round_jiffies to align wakeups and reduce power.
* Remove atl1_watchdog which does nothing but rearm itself
* Use setup_timer() function
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is now a net_device_stats structure inside net_device that should
be used if possible by devices. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was being discussed where we would put this, but now it found a home
so use its define.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_keyreset returns true in either branch.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If card is using downloadable firmware (like Agere 9.x), firmware has
to be reloaded during resume. It is not possible to use request_firmware
for that, because tasks are still frozen, so request_firmware will
just timeout and fail. So cache firmware image in memory for later
reuse in ->resume method.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On resume card state is likely lost so we have to reload firmware
again.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Properly get/set all available ISR/IMR values and review common/uncommon bits
*Better handling of per-txq interrupts (we can now resolve what q is generating
each interrupt -this will help in debuging wme later)
*Some minor updates from legacy-hal
*Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set
them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM
and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested
it on various cards and it works fine.
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reclaim flag should include REPLY_RX_MPDU_CMD in the list of commands
issued by uCode. This is for safety in case the SEQ_RX_FRAME bit is set
incorrectly.
Signed-off-by: Daniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem fixed here is that iwl3945_mac_get_tsf() returns 0, as the
function is not implemented, and this is considered as a valid value by
the mac layer in mlme.c:1605. The consequence is that the STA in ad-hoc
mode is inserted/removed quite frequently due to IBSS merging.
This patch fixes :
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1781
and https://bugzilla.redhat.com/show_bug.cgi?id=459401
Signed-off-by: Fabrice Bellet <fabrice@bellet.info>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch drops unreadable usage of IWL_SET/GET_BITS16 in byte count
tables handling
This patch also cleans a bit the byte count table code and adds
WARN_ON traps on invalid values
This patch is pure cleanup, no functional changes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver does not properly convert rate_n_flags to PLCP index for mimo3
packets. This makes mac80211 drop the packets
Signed-off-by: Daniel C. Halperin <daniel.c.halperin@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since calibration framework is not HW specific remove 5000 and 4965 prefix
This patch doesn't provide any functional changes only code renaming
and movement
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses new parameters eeprom_ver and eeprom_calib_ver
to support additional HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that station table is not accessed
with invalid station id in 4965 TX response path
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch utilize 5000 new TX response command
which contains all necessary information and avoids
back referencing to the original TX frame.
It also change handling of software queue tracking
4965 flow is aligned with changes as much as possible.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were also changing tx power even when we were not asked to,
this enforces the change only when we are asked nicely. When
not asked we simply try to use the max power, we don't tx power
at all for rate control.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables hardware interrupt mitigation on RX.
It should alleviate system interrupt load intelligently.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sc_txintrperiod is currently set to 0 and never updated. We won't
be using this, if anything we will consider using TX interrupt
mitigation but that is different and not yet tested. So remove
sc_txintrperiod and the pointless spin_lock_bh() on tx prepare.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unnecessary and of questionable value. Also remove
is_empty_ssid, as it is also unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs_create_bool() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the rt2x00 driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the ath5k driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A compilation with the command "make C=2 CF="-D__CHECK_ENDIAN__" \
drivers/net/wireless/hostap/"
yields the following warnings:
CHECK drivers/net/wireless/hostap/hostap_info.c
drivers/net/wireless/hostap/hostap_info.c:156:43: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:156:43: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:156:43: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:294:44: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:294:44: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:294:44: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:487:12: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:487:12: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:487:12: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:491:12: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:491:12: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:491:12: got long *<noident>
The warnings are fixed with the following compile-tested fix:
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch protects iwl-csr.h and iwl-fh.h from double inclusion
by ifndef define endif idiom
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes most/all? of the "magic" numbers and unknown structure
variables inside the code and replaces them with meaningful prototypes.
(Plus a one line warning fix from Larry Finger <Larry.Finger@lwfinger.net>.)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch initialize all remaining values which are necessary for
SPI firmwares.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have to be careful if multiple "control frames" are passed in a very short intervals to
the device's firmware. As p54_assign_address always put them into same memory location.
To guarantee that this won't happen anymore, we have to treat control frames like normal
data frames in the devices own memory management.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the long names and the nesting in p54_rx_frame_sent really
became a "line longer than 80 characters" problem.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch series hopefully increases p54's "longterm" stability.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes clear that tx command is attached to the same tfd as
the tx packet
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch:
1. fixes command DMA unmapping, this might be visible only
on platforms where DMA unmapping is no noop such as PPC64 (not tested)
2. attaches correctly high memory part of the host command buffer
3. changes structure of TFD TB
instead of describing transmit buffer (TB) tuple it describes single
TB and makes code more readable on price of one unaligned access
4. eliminates using of IWL_GET/SET_BITs for TFD handling
5. renames TFD structures to mach the HW spec
6. reduces iwl_tx_info size by reserving first TB to the host command
This patch should not have any visible effect on x86 32
This patch is rework of
iwlwifi: fix DMA code and bugs from
Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX antenna toggling is requested for management frames in tx and
scanning. I addition toggling in scanning was incorrect;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds iwl_cmd_queue_free function and
separate cmd queue freeing from regular tx queue freeing.
This improves readability and adds one more step in
restructuring of cmd queue handling
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes host commands structures from iwl_cmd
to make more HW oblivious
tx cmd was left it needs special treatment.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
change desc_lookup from hard coded switch to a simple lookup table and expand
list to include all errors. Also corrected output using this string so info
is aligned and easier to read when debugging issues.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
string repeated for definition of ucode firmware file and in preparation for
multiple firmware files need to consolidate location for their definition.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Acked-by: Tomas Winkler <tomas.winler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not attempt association until directed to do so by a user space
application. In particular, this avoids race conditions with
NetworkManager association state.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements multi-rate retry in p54. With lots of help
and testing from Christian and the limiting idea from nbd.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.
In this driver, I don't simply use netdev_priv() to replace netdev->priv.
The reason is:
Pointer netdev->priv was changed in this driver, but it shouldn't.
Because the memory was allocated when alloc_netdev() and netdev->priv
should always point to that memory.
So I use netdev->ml_priv to replace netdev->priv.
After replacing, both ai and ai->wifidev->ml_priv point to the same memory.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mesh point operation (thanks to YanBo for pointing
out the problem): make mesh point interfaces start beaconing when
they come up and configure the RX filter in mesh mode so that mesh
beacons and action frames are received. Add mesh point to the check
in ath5k_add_interface. Tested with multiple AR5211 cards.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adjusts ath5k's signal quality reporting taking into
consideration received beacons at an RSSI of 35 should indicate
you can use of 54 Mbps on a single stream card (all ath5k cards)
reliably.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adjusts ath9k's signal quality reporting taking into
consideration received beacons at an RSSI of 45 should indicate
you can use of MCS 15 rate (144 Mbps) reliably on dual stream card.
Keep in mind mac80211 does not yet have aggregation fixed but this
should still provide more accurate results.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds short slot handling for 8187B variant of rtl8187 chips.
Some things to note about changes done:
* Values used are chosen to met 802.11-2007 spec. This raised a question
about SIFS value used with 8187L: 0x22 (34) doesn't match any spec
value. For now just don't change 8187L, but is something to be
looked at.
* On 8187B, the location of EIFS register is at the same place as BRSR+1
of struct rtl818x_csr. Unfortunately there is no clean way to
accomodate 8187B differences currently, just use address of BRSR+1 and
comment about it. The same thing happens for Ack timeout register,
that is on CARRIER_SENSE_COUNTER location of 8187L. The eifs and ack
timeout values are in units of 4us. All these registers information
was gathered from references being the vendor gpl driver and 8180
datasheet, unfortunately there is no information about this on 8187B
datasheet. Also the ack timeout value was inspired by the same
calculation as done on rt2x00.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates 8187L handling for short slot after "mac80211: fix short
slot handling". For 8187B, there was no handling done for short slot
timing so nothing done, support for it will come in a following patch.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for AP mode. This involves:
- enablement in ath5k_beacon_config -- initialize beacon timer
- add AP to the supported modes in ath5k_add_interface
- handle beacon change even for AP in ath5k_config_interface
- remove useless test for IBSS in ath5k_beacon_update
Note that it doesn't enable the AP mode for the driver. It must
be enabled by NL80211_IFTYPE_AP bit added to interface_modes.
v2:
Fixed opmode constant (IEEE80211_ to NL80211_)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sorry about that, for some reason I didn't notice that I'd
left some unused variables in there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT handling has the following deficiencies, which I've
(partially) fixed:
* it always uses the AP info even if there is no AP,
hence has no chance of working as an AP
* it pretends to be HW config, but really is per-BSS
* channel sanity checking is left to the drivers
* it generally lets the driver control too much
HT enabling is still wrong with this patch if you have more than
one virtual STA mode interface, but that never happens currently.
Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be
wrong, see the comment in ieee80211_enable_ht().
Additionally, this fixes a number of bugs:
* mac80211: ieee80211_set_disassoc doesn't notify the driver any
more since the refactoring
* iwl-agn-rs: always uses the HT capabilities from the wrong stuff
mac80211 gives it rather than the actual peer STA
* ath9k: a number of bugs resulting from the broken HT API
I'm not entirely happy with putting the HT capabilities into
struct ieee80211_sta as restricted to our own HT TX capabilities,
but I see no cleaner solution for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Probably bugs I added.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.
This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch entitled "[PATCH] p54: Fix sparse warnings" added the __le16
variable rx_mtu to struct bootrec, but it could equally well be placed
in the struct bootrec_desc, which overlays the 'data' section of bootrec.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up a number of things:
* the unusable definition of the HT capabilities/HT information
information elements
* variable names that are hard to understand
* mac80211: move ieee80211_handle_ht to ht.c and remove the unused
enable_ht parameter
* mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
* mac80211: fix bug with casting the result of ieee80211_bss_get_ie
to an information element _contents_ rather than the
whole element, add size checking (another out-of-bounds
access bug fixed!)
* mac80211: remove some unused return values in favour of BUG_ON
checking
* a few minor other things
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch was made on behalf of Johannes request.
"mac80211 and IEEE80211_CONF_SHORT_SLOT_TIME"
Of course, bss_info_changed provides some more useful data.
e.g.: basic_rates, dtim_period, beacon_int and maybe even more.
Everything can be hooked up if it's necessary.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a typo in mac80211_hwsim.c:
use HWSIM_STA_MAGIC in hwsim_check_sta_magic() and hwsim_set_sta_magic()
instead of HWSIM_VIF_MAGIC.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors rxon time command. It removes the usage of union tsf
in favor of u64 value and hopefully makes code more readable. There are
no functional changes in this patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch selects a valid antennae upon rate scale init. This solves a
SYSASSERT complaining that the driver is setting a non valid antenna in
the LQ CMD.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds ability to configure initial calibration set. Not all HW
supported by iwlwifi use the same calibration set, XTAL is one example.
Some clean ups are also included in this patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Saikiran Madugula, commit 7447ef63cf
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess kernel-doc function parameters from networking header
& driver files:
Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move SKB trim before we lookup the socket so we don't have to
put it on failure.
Based upon an initial patch by Jarek Poplawski and suggestions
from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the newly introduced pci_ioremap_bar() function in drivers/net.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement ethtool's get_flags and set_flags methods.
It enables ethtool to control the LRO settings.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adapt the e100 driver to the reworked PCI PM
* Use the observation that it is sufficient to call pci_enable_wake()
once, unless it fails
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adapt the skge driver to the reworked PCI PM
* Use device_set_wakeup_enable() and friends as needed
* Remove an open-coded reference to the standard PCI PM registers
* Use pci_prepare_to_sleep() and pci_back_from_sleep() in the
->suspend() and ->resume() callbacks
* Use the observation that it is sufficient to call pci_enable_wake()
once, unless it fails
Tested on Asus L5D (Yukon-Lite rev 7).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 401c0aabec introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.
This patch causes the VLAN tag to be stored in its proper location.
Tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:
bond_close()
bond_alb_deinitialize()
tlb_deinitialize()
kfree(bond_info->tx_hashtbl)
bond_info->tx_hashtbl = NULL
Unfortunately if there are still slaves in the bond, when removing the
module the following happens:
bonding_exit()
bond_free_all()
bond_release_all()
bond_alb_deinit_slave()
tlb_clear_slave()
tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
u32 next_index = tx_hash_table[index].next
As you might guess we panic when trying to access a few entries into the
table that no longer exists.
I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine. It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch reworks the resource free logic performed at the time
a bonding device is released. This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.
"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During the rework of the mii monitor for:
commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
I left out the increment of the link failure counter. This
patch corrects that omission.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As a bonus, removes some unnecessary byteswapping.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If macvlan's are used, it is useful to propgate speed and other settings
from underlying device up for application usage.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were setting RX_FILTER_BEACON even after entering STA mode,
which leads to a lot of unnecessary wakeups. This should fix the
bug "Ath5k driver has too many interrupts per second at idle" at
http://bugzilla.kernel.org/show_bug.cgi?id=11749.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take care to handle register 0xa228 exactly as in the HAL released by
Atheros. This change is required to make ath5k work again on my system
since commit 2203d6be (ath5k: Misc hw_reset updates), thus fixing a
regression in 2.6.27 and therefore hopefully eligible for inclusion into
a stable release.
v2: Only overwrite initial register values on later revisions of AR5212
chips.
v3: Use standard macros to manipulate the register.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make menuconfig RT2X00 a tristate instead of boolean,
otherwise we do not correctly inherit the mac80211 value
on which RT2X00 depends, and makes it possible to
compile rt2x00 into the kernel while mac80211 is a
module.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If somebody sends an invalid beacon/probe response, that can trash the
whole BSS descriptor. The descriptor is, luckily, large enough so that
it cannot scribble past the end of it; it's well above 400 bytes long.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.24-2.6.27, bug present in some form since driver was added (2.6.22)]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg detected this two sparse warnings:
drivers/net/wireless/libertas/cmd.c:609:16: warning: cast to restricted __le16
drivers/net/wireless/libertas/cmd.c:611:16: warning: cast to restricted __le16
... but cmd.minlevel is "s8", so we can access it directly and hope
for the sign-extension-code in the compiler to convert that to the
"s16" type.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes suspend to RAM after by moving
notify_mac out of iwlwifi mutex
http://bugzilla.kernel.org/show_bug.cgi?id=11845
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The veth network device is stored in a list in the netdev private.
AFAICS, this list is never used so I removed this list from the code.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The veth private structure contains a netdev pointer refering to its peer.
This field is never used and it is pointless because if we can access,
the veth_priv, that means we already have the netdev which is stored
in veth_priv->dev.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd8111e rx poll routine currently mishandles the case when we
process exactly the number of packets specified in the budget.
This patch is basically as suggested by David Miller.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
