commit 1e249cb5b7 upstream.
When lazytime is enabled and an inode is being written due to its
in-memory updated timestamps having expired, either due to a sync() or
syncfs() system call or due to dirtytime_expire_interval having elapsed,
the VFS needs to inform the filesystem so that the filesystem can copy
the inode's timestamps out to the on-disk data structures.
This is done by __writeback_single_inode() calling
mark_inode_dirty_sync(), which then calls ->dirty_inode(I_DIRTY_SYNC).
However, this occurs after __writeback_single_inode() has already
cleared the dirty flags from ->i_state. This causes two bugs:
- mark_inode_dirty_sync() redirties the inode, causing it to remain
dirty. This wastefully causes the inode to be written twice. But
more importantly, it breaks cases where sync_filesystem() is expected
to clean dirty inodes. This includes the FS_IOC_REMOVE_ENCRYPTION_KEY
ioctl (as reported at
https://lore.kernel.org/r/20200306004555.GB225345@gmail.com), as well
as possibly filesystem freezing (freeze_super()).
- Since ->i_state doesn't contain I_DIRTY_TIME when ->dirty_inode() is
called from __writeback_single_inode() for lazytime expiration,
xfs_fs_dirty_inode() ignores the notification. (XFS only cares about
lazytime expirations, and it assumes that i_state will contain
I_DIRTY_TIME during those.) Therefore, lazy timestamps aren't
persisted by sync(), syncfs(), or dirtytime_expire_interval on XFS.
Fix this by moving the call to mark_inode_dirty_sync() to earlier in
__writeback_single_inode(), before the dirty flags are cleared from
i_state. This makes filesystems be properly notified of the timestamp
expiration, and it avoids incorrectly redirtying the inode.
This fixes xfstest generic/580 (which tests
FS_IOC_REMOVE_ENCRYPTION_KEY) when run on ext4 or f2fs with lazytime
enabled. It also fixes the new lazytime xfstest I've proposed, which
reproduces the above-mentioned XFS bug
(https://lore.kernel.org/r/20210105005818.92978-1-ebiggers@kernel.org).
Alternatively, we could call ->dirty_inode(I_DIRTY_SYNC) directly. But
due to the introduction of I_SYNC_QUEUED, mark_inode_dirty_sync() is the
right thing to do because mark_inode_dirty_sync() now knows not to move
the inode to a writeback list if it is currently queued for sync.
Fixes: 0ae45f63d4 ("vfs: add support for a lazytime mount option")
Cc: stable@vger.kernel.org
Depends-on: 5afced3bf2 ("writeback: Avoid skipping inode writeback")
Link: https://lore.kernel.org/r/20210112190253.64307-2-ebiggers@kernel.org
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fcd57505c upstream.
The only use of I_DIRTY_TIME_EXPIRE is to detect in
__writeback_single_inode() that inode got there because flush worker
decided it's time to writeback the dirty inode time stamps (either
because we are syncing or because of age). However we can detect this
directly in __writeback_single_inode() and there's no need for the
strange propagation with I_DIRTY_TIME_EXPIRE flag.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c02406428 upstream.
Otherwise a malicious user could (ab)use the "recalculate" feature
that makes dm-integrity calculate the checksums in the background
while the device is already usable. When the system restarts before all
checksums have been calculated, the calculation continues where it was
interrupted even if the recalculate feature is not requested the next
time the dm device is set up.
Disable recalculating if we use internal_hash or journal_hash with a
key (e.g. HMAC) and we don't have the "legacy_recalculate" flag.
This may break activation of a volume, created by an older kernel,
that is not yet fully recalculated -- if this happens, the user should
add the "legacy_recalculate" flag to constructor parameters.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Daniel Glockner <dg@emlix.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8a950d0d3 upstream.
Several Makefiles in tools/ need to define the host toolchain variables.
Move their definition to tools/scripts/Makefile.include
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/bpf/20201110164310.2600671-2-jean-philippe@linaro.org
Cc: Alistair Delva <adelva@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7955f105af upstream.
In the negotiate protocol preauth context, the server is not required
to populate the salt (although it is done by most servers) so do
not warn on mount.
We retain the checks (warn) that the preauth context is the minimum
size and that the salt does not exceed DataLength of the SMB response.
Although we use the defaults in the case that the preauth context
response is invalid, these checks may be useful in the future
as servers add support for additional mechanisms.
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc1a0f9e1 upstream.
On arm64, the global variable memstart_addr represents the physical
address of PAGE_OFFSET, and so physical to virtual translations or
vice versa used to come down to simple additions or subtractions
involving the values of PAGE_OFFSET and memstart_addr.
When support for 52-bit virtual addressing was introduced, we had to
deal with PAGE_OFFSET potentially being outside of the region that
can be covered by the virtual range (as the 52-bit VA capable build
needs to be able to run on systems that are only 48-bit VA capable),
and for this reason, another translation was introduced, and recorded
in the global variable physvirt_offset.
However, if we go back to the original definition of memstart_addr,
i.e., the physical address of PAGE_OFFSET, it turns out that there is
no need for two separate translations: instead, we can simply subtract
the size of the unaddressable VA space from memstart_addr to make the
available physical memory appear in the 48-bit addressable VA region.
This simplifies things, but also fixes a bug on KASLR builds, which
may update memstart_addr later on in arm64_memblock_init(), but fails
to update vmemmap and physvirt_offset accordingly.
Fixes: 5383cc6efe ("arm64: mm: Introduce vabits_actual")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Link: https://lore.kernel.org/r/20201008153602.9467-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbeb97464e upstream.
Below race can come, if trace_open and resize of
cpu buffer is running parallely on different cpus
CPUX CPUY
ring_buffer_resize
atomic_read(&buffer->resize_disabled)
tracing_open
tracing_reset_online_cpus
ring_buffer_reset_cpu
rb_reset_cpu
rb_update_pages
remove/insert pages
resetting pointer
This race can cause data abort or some times infinte loop in
rb_remove_pages and rb_insert_pages while checking pages
for sanity.
Take buffer lock to fix this.
Link: https://lkml.kernel.org/r/1601976833-24377-1-git-send-email-gkohli@codeaurora.org
Cc: stable@vger.kernel.org
Fixes: 83f40318da ("ring-buffer: Make removal of ring buffer pages atomic")
Reported-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Gaurav Kohli <gkohli@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No upstream commit, this is a fix to a stable 5.4 specific backport.
The intention of backport commit cac68d12c5 ("io_uring: grab ->fs as part
of async offload") as found in the stable 5.4 tree was to make
io_sq_wq_submit_work() to switch the workqueue task's ->fs over to the
submitting task's one during the IO operation.
However, due to a small logic error, this change turned out to not have any
actual effect. From a high level, the relevant code in
io_sq_wq_submit_work() looks like
old_fs_struct = current->fs;
do {
...
if (req->fs != current->fs && current->fs != old_fs_struct) {
task_lock(current);
if (req->fs)
current->fs = req->fs;
else
current->fs = old_fs_struct;
task_unlock(current);
}
...
} while (req);
The if condition is supposed to cover the case that current->fs doesn't
match what's needed for processing the request, but observe how it fails
to ever evaluate to true due to the second clause:
current->fs != old_fs_struct will be false in the first iteration as per
the initialization of old_fs_struct and because this prevents current->fs
from getting replaced, the same follows inductively for all subsequent
iterations.
Fix said if condition such that
- if req->fs is set and doesn't match current->fs, the latter will be
switched to the former
- or if req->fs is unset, the switch back to the initial old_fs_struct
will be made, if necessary.
While at it, also correct the condition for the ->fs related cleanup right
before the return of io_sq_wq_submit_work(): currently, old_fs_struct is
restored only if it's non-NULL. It is always non-NULL though and thus, the
if-condition is rendundant. Supposedly, the motivation had been to optimize
and avoid switching current->fs back to the initial old_fs_struct in case
it is found to have the desired value already. Make it so.
Cc: stable@vger.kernel.org # v5.4
Fixes: cac68d12c5 ("io_uring: grab ->fs as part of async offload")
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 179e8e47c0 upstream.
The recent commit to fix a memory leak introduced an inadvertant NULL
pointer dereference. The `wacom_wac->pen_fifo` variable was never
intialized, resuling in a crash whenever functions tried to use it.
Since the FIFO is only used by AES pens (to buffer events from pen
proximity until the hardware reports the pen serial number) this would
have been easily overlooked without testing an AES device.
This patch converts `wacom_wac->pen_fifo` over to a pointer (since the
call to `devres_alloc` allocates memory for us) and ensures that we assign
it to point to the allocated and initalized `pen_fifo` before the function
returns.
Link: https://github.com/linuxwacom/input-wacom/issues/230
Fixes: 37309f47e2 ("HID: wacom: Fix memory leakage caused by kfifo_alloc")
CC: stable@vger.kernel.org # v4.19+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34b1a1ce14 upstream
fixup_pi_state_owner() tries to ensure that the state of the rtmutex,
pi_state and the user space value related to the PI futex are consistent
before returning to user space. In case that the user space value update
faults and the fault cannot be resolved by faulting the page in via
fault_in_user_writeable() the function returns with -EFAULT and leaves
the rtmutex and pi_state owner state inconsistent.
A subsequent futex_unlock_pi() operates on the inconsistent pi_state and
releases the rtmutex despite not owning it which can corrupt the RB tree of
the rtmutex and cause a subsequent kernel stack use after free.
It was suggested to loop forever in fixup_pi_state_owner() if the fault
cannot be resolved, but that results in runaway tasks which is especially
undesired when the problem happens due to a programming error and not due
to malice.
As the user space value cannot be fixed up, the proper solution is to make
the rtmutex and the pi_state consistent so both have the same owner. This
leaves the user space value out of sync. Any subsequent operation on the
futex will fail because the 10th rule of PI futexes (pi_state owner and
user space value are consistent) has been violated.
As a consequence this removes the inept attempts of 'fixing' the situation
in case that the current task owns the rtmutex when returning with an
unresolvable fault by unlocking the rtmutex which left pi_state::owner and
rtmutex::owner out of sync in a different and only slightly less dangerous
way.
Fixes: 1b7558e457 ("futexes: fix fault handling in futex_lock_pi")
Reported-by: gzobqq@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2dac39d93 upstream
Too many gotos already and an upcoming fix would make it even more
unreadable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ccc84f917 upstream
No point in open coding it. This way it gains the extra sanity checks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2156ac1934 upstream
Nothing uses the argument. Remove it as preparation to use
pi_state_update_owner().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5cade200a upstream
Updating pi_state::owner is done at several places with the same
code. Provide a function for it and use that at the obvious places.
This is also a preparation for a bug fix to avoid yet another copy of the
same code or alternatively introducing a completely unpenetratable mess of
gotos.
Originally-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b79c5520 upstream
If that unexpected case of inconsistent arguments ever happens then the
futex state is left completely inconsistent and the printk is not really
helpful. Replace it with a warning and make the state consistent.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12bb3f7f1b upstream
In case that futex_lock_pi() was aborted by a signal or a timeout and the
task returned without acquiring the rtmutex, but is the designated owner of
the futex due to a concurrent futex_unlock_pi() fixup_owner() is invoked to
establish consistent state. In that case it invokes fixup_pi_state_owner()
which in turn tries to acquire the rtmutex again. If that succeeds then it
does not propagate this success to fixup_owner() and futex_lock_pi()
returns -EINTR or -ETIMEOUT despite having the futex locked.
Return success from fixup_pi_state_owner() in all cases where the current
task owns the rtmutex and therefore the futex and propagate it correctly
through fixup_owner(). Fixup the other callsite which does not expect a
positive return value.
Fixes: c1e2f0eaf0 ("futex: Avoid violating the 10th rule of futex")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 757fed1d08 upstream.
This reverts commit dde3c6b72a.
syzbot report a double-free bug. The following case can cause this bug.
- mm/slab_common.c: create_cache(): if the __kmem_cache_create() fails,
it does:
out_free_cache:
kmem_cache_free(kmem_cache, s);
- but __kmem_cache_create() - at least for slub() - will have done
sysfs_slab_add(s)
-> sysfs_create_group() .. fails ..
-> kobject_del(&s->kobj); .. which frees s ...
We can't remove the kmem_cache_free() in create_cache(), because other
error cases of __kmem_cache_create() do not free this.
So, revert the commit dde3c6b72a ("mm/slub: fix a memory leak in
sysfs_slab_add()") to fix this.
Reported-by: syzbot+d0bd96b4696c1ef67991@syzkaller.appspotmail.com
Fixes: dde3c6b72a ("mm/slub: fix a memory leak in sysfs_slab_add()")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e73b0101ae upstream.
The period is the sum of on and off values. That is, calculate period as
($on + $off) / clkrate
instead of
$off / clkrate - $on / clkrate
that makes no sense.
Reported-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[baruch: backport to kernels <= v5.10]
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d9b1ee0b2 upstream.
The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.
The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():
RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
as long as the receiver continues to respond probes. We support
this by default and reset icsk_probes_out with incoming ACKs.
This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell <jmaxwell37@gmail.com> for diagnosing the
actual issue.
In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.
Fixes: 9721e709fa ("tcp: simplify window probe aborting on USER_TIMEOUT")
Reported-by: William McCall <william.mccall@gmail.com>
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b160c28548 upstream.
Heiner Kallweit reported that some skbs were sent with
the following invalid GSO properties :
- gso_size > 0
- gso_type == 0
This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2.
Juerg Haefliger was able to reproduce a similar issue using
a lan78xx NIC and a workload mixing TCP incoming traffic
and forwarded packets.
The problem is that tcp_add_backlog() is writing
over gso_segs and gso_size even if the incoming packet will not
be coalesced to the backlog tail packet.
While skb_try_coalesce() would bail out if tail packet is cloned,
this overwriting would lead to corruptions of other packets
cooked by lan78xx, sharing a common super-packet.
The strategy used by lan78xx is to use a big skb, and split
it into all received packets using skb_clone() to avoid copies.
The drawback of this strategy is that all the small skb share a common
struct skb_shared_info.
This patch rewrites TCP gso_size/gso_segs handling to only
happen on the tail skb, since skb_try_coalesce() made sure
it was not cloned.
Fixes: 4f693b55c3 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Juerg Haefliger <juergh@canonical.com>
Tested-by: Juerg Haefliger <juergh@canonical.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423
Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e4052c32d upstream.
The > comparison should be >= to prevent accessing one element beyond
the end of the dev->vlans[] array in the caller function, b53_vlan_add().
The "dev->vlans" array is allocated in the b53_switch_init() function
and it has "dev->num_vlans" elements.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79267ae226 upstream.
The blamed commit was too aggressive, and it made ocelot_netdevice_event
react only to network interface events emitted for the ocelot switch
ports.
In fact, only the PRECHANGEUPPER should have had that check.
When we ignore all events that are not for us, we miss the fact that the
upper of the LAG changes, and the bonding interface gets enslaved to a
bridge. This is an operation we could offload under certain conditions.
Fixes: 7afb3e575e ("net: mscc: ocelot: don't handle netdev events for other netdevs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210118135210.2666246-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ceed9038b2 upstream.
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303 upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b51b008 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db7 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a11a496ee6 upstream.
During testing kasan_populate_early_shadow and kasan_remove_zero_shadow,
if the shadow start and end address in kasan_remove_zero_shadow() is not
aligned to PMD_SIZE, the remain unaligned PTE won't be removed.
In the test case for kasan_remove_zero_shadow():
shadow_start: 0xffffffb802000000, shadow end: 0xffffffbfbe000000
3-level page table:
PUD_SIZE: 0x40000000 PMD_SIZE: 0x200000 PAGE_SIZE: 4K
0xffffffbf80000000 ~ 0xffffffbfbdf80000 will not be removed because in
kasan_remove_pud_table(), kasan_pmd_table(*pud) is true but the next
address is 0xffffffbfbdf80000 which is not aligned to PUD_SIZE.
In the correct condition, this should fallback to the next level
kasan_remove_pmd_table() but the condition flow always continue to skip
the unaligned part.
Fix by correcting the condition when next and addr are neither aligned.
Link: https://lkml.kernel.org/r/20210103135621.83129-1-lecopzer@gmail.com
Fixes: 0207df4fa1 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN")
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: YJ Chiang <yj.chiang@mediatek.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c556025d upstream.
Commit 3226b158e6 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e1 ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9778448175 upstream.
The allocated page is not released if error occurs in
nvm_submit_io_sync_raw(). __free_page() is moved ealier to avoid
possible memory leak issue.
Fixes: aff3fb18f9 ("lightnvm: move bad block and chunk state logic to core")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a2e94b3f upstream.
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff7 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87fe04367d upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes: 92307069a9 (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f477a538c1 upstream.
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed7
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
Fixes: d8902adcc1 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5a6266fb upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes: 8f97339d3f ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76e2fc63ca upstream.
Set the maximum DIE per package variable on AMD using the
NodesPerProcessor topology value. This will be used by RAPL, among
others, to determine the maximum number of DIEs on the system in order
to do per-DIE manipulations.
[ bp: Productize into a proper patch. ]
Fixes: 028c221ed1 ("x86/CPU/AMD: Save AMD NodeId as cpu_die_id")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Reported-by: Rafael Kitover <rkitover@gmail.com>
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Tested-by: Rafael Kitover <rkitover@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210939
Link: https://lkml.kernel.org/r/20210106112106.GE5729@zn.tnic
Link: https://lkml.kernel.org/r/20210111101455.1194-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a85c09a3f upstream.
- JZ4760 and JZ4760B have a similar register layout as the JZ4740, and
don't use the new register layout, which was introduced with the
JZ4770 SoC and not the JZ4760 or JZ4760B SoCs.
- The JZ4740 code path only expected two function modes to be
configurable for each pin, and wouldn't work with more than two. Fix
it for the JZ4760, which has four configurable function modes.
Fixes: 0257595a5c ("pinctrl: Ingenic: Add pinctrl driver for JZ4760 and JZ4760B.")
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1cf435e2 upstream.
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7e0c3c29 upstream.
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 576667bad3 upstream.
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
Cc: <stable@vger.kernel.org>
Tested-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef02684c4e upstream.
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e0dcf62ab upstream.
The vhub engine has two dma mode, one is descriptor list, another
is single stage DMA. Each mode has different stop register setting.
Descriptor list operation (bit2) : 0 disable reset, 1: enable reset
Single mode operation (bit0) : 0 : disable, 1: enable
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210108081238.10199-2-ryan_chen@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 643a4df7fe upstream.
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1610416647-45774-1-git-send-email-liulongfang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 280a9045bb upstream.
According to EHCI spec, EHCI HC clears USBSTS.HCHalted whenever
USBCMD.RS=1.
However, it is a good practice to wait some time after setting USBCMD.RS
(approximately 100ms) until USBSTS.HCHalted become zero.
Without this waiting, VirtualBox's EHCI virtual HC accidentally hangs
(see BugLink).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211095
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugene Korenevsky <ekorenevsky@astralinux.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210110173609.GA17313@himera.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ca955b5a upstream.
Commit c685af1108 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 927633a6d2 upstream.
In stm_heartbeat_init(): return value gets reset after the first
iteration by stm_source_register_device(), so allocation failures
after that will, after a clean up, return success. Fix that.
Fixes: 1192918530 ("stm class: Add heartbeat stm source device")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hui <john.wanghui@huawei.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20210115195917.3184-2-alexander.shishkin@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Biggers