When commit 9017dc4fbd ("pwm: jz4740: Enhance precision in calculation
of duty cycle") from v5.8-rc1 was backported to v5.4.x its dependency on
commit ce1f9cece0 ("pwm: jz4740: Use clocks from TCU driver") was not
noticed which made the pwm-jz4740 driver fail to build.
As ce1f9cece0 depends on still more rework, just backport a small part
of this commit to make the driver build again. (There is no dependency
on the functionality introduced in ce1f9cece0, just the rate variable
is needed.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9017dc4fbd upstream.
Calculating the hardware value for the duty from the hardware value of
the period resulted in a precision loss versus calculating it from the
clock rate directly.
(Also remove a cast that doesn't really need to be here)
Fixes: f6b8a57000 ("pwm: Add Ingenic JZ4740 support")
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
[ukl: backport to v5.4.y and adapt commit log accordingly]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca162ce981 ]
Even in failed case of pm_runtime_get_sync(), the usage_count is
incremented. In order to keep the usage_count with correct value call
appropriate pm_runtime_put().
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c25b07e5e ]
The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().
Fixes: e5a06dc5ac ("pwm: Add BCM2835 PWM driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5a3c7a453 ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.
Fixes: 99b82abb0a ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1451a3eed2 ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should be disabled after the removal of the PWM
chip.
Fixes: ed6c1476bf ("pwm: Add support for R-Car PWM Timer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9cc5f232a4 upstream.
This driver allows pwms to be requested as gpios via gpiolib. Obviously,
it should not be allowed to request a GPIO when its corresponding PWM is
already requested (and vice versa). So it requires some exclusion code.
Given that the PWMm and GPIO cores are not synchronized with respect to
each other, this exclusion code will also require proper
synchronization.
Such a mechanism was in place, but was inadvertently removed by Uwe's
clean-up in commit e926b12c61 ("pwm: Clear chip_data in pwm_put()").
Upon revisiting the synchronization mechanism, we found that
theoretically, it could allow two threads to successfully request
conflicting PWMs/GPIOs.
Replace with a bitmap which tracks PWMs in-use, plus a mutex. As long as
PWM and GPIO's respective request/free functions modify the in-use
bitmap while holding the mutex, proper synchronization will be
guaranteed.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: e926b12c61 ("pwm: Clear chip_data in pwm_put()")
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.org/lkml/2019/5/31/963
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[cg: Tested on an i.MX6Q board with two NXP PCA9685 chips]
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com> # cg's rebase
Link: https://lore.kernel.org/lkml/20200330160238.GD2817345@ulmo/
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7cb3a1dd5 upstream.
This was found by coccicheck:
drivers/pwm/pwm-omap-dmtimer.c:304:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 255, but without a corresponding
object release within this function.
Reported-by: Markus Elfring <elfring@users.sourceforge.net>
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9871abffc8 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pwm/pwm-pca9685.c: In function ‘pca9685_pwm_gpio_free’:
drivers/pwm/pwm-pca9685.c:162:21: warning: variable ‘pwm’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed. In that case, hold and release
the lock 'pca->lock' can be removed since nothing will be done between
them.
Fixes: e926b12c61 ("pwm: Clear chip_data in pwm_put()")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43efdc8f0e ]
In the old code (e.g.) mutex_destroy() was called before
pwmchip_remove(). Between these two calls it is possible that a PWM
callback is used which tries to grab the mutex.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4cf7aa57e ]
Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.
This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.
Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50cc7e3e4f ]
Since 5.4-rc1, pwm_apply_state calls ->get_state after ->apply
if available, and this revealed an issue with integer precision
when calculating duty_cycle and period for the currently set
state in ->get_state callback.
This issue manifested in broken backlight on several Allwinner
based devices.
Previously this worked, because ->apply updated the passed state
directly.
Fixes: deb9c462f4 ("pwm: sun4i: Don't update the state for the caller of pwm_apply_state")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes: daa5abc41c ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It turns out that commit 01ccf903ed ("pwm: Let pwm_get_state() return
the last implemented state") causes backlight failures on a number of
boards. The reason is that some of the drivers do not write the full
state through to the hardware registers, which means that ->get_state()
subsequently does not return the correct state. Consumers which rely on
pwm_get_state() returning the current state will therefore get confused
and subsequently try to program a bad state.
Before this change can be made, existing drivers need to be more
carefully audited and fixed to behave as the framework expects. Until
then, keep the original behaviour of returning the software state that
was applied rather than reading the state back from hardware.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of, mostly
minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS file,
making official his role as a reviewer.
-----BEGIN PGP SIGNATURE-----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=C9sW
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
This adds pwm support for MT7629, and separate mt7629 compatible string
from mt7622
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add SPDX identifiers to pwm-mediatek.c. Update MODULE_LICENSE to
correctly reflect the GNU General Public License v2.0.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use pwm_mediatek as common prefix to match the filename. No functional
change intended.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of using fixed size of arrays, allocate the memory for them
based on the number of PWMs specified for each SoC generation.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
We can use fixed clocks to repair mt7628 PWM during configure from
userspace. The SoC is legacy MIPS and has no complex clock tree. Because
we can get the clock frequency for period calculation from fixed clocks
specified in DT, we can remove the has_clock field, and directly use
devm_clk_get() and clk_get_rate().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch drop the check for of_device_get_match_data. Due to the only
way call driver probe is compatible match. The data pointer which points
to the SoC specify data is directly set by driver, and it should not be
NULL in our case. We can safety remove the check for the result of
of_device_get_match_data().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the driver is now exclusively DT, it only binds if it finds a
match in the of_device_id table. But in that case the associated data
can never be NULL, so drop the unnecessary check.
While at it, drop the extra local variable and store the pointer to
this per-SoC data in the driver data directly.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since commit 26202873bb ("avr32: remove support for AVR32
architecture") there is no more user of platform_device_id and we
should only use dt bindings
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
LPTimer can use a 32KHz clock for counting. It depends on clock tree
configuration. In such a case, PWM output frequency range is limited.
Although unlikely, nothing prevents user from requesting a PWM frequency
above counting clock (32KHz for instance):
- This causes (prd - 1) = 0xffff to be written in ARR register later in
the apply() routine.
This results in badly configured PWM period (and also duty_cycle).
Add a check to report an error is such a case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:
#define PERIOD 5000000
#define DUTY_LITTLE 10
...
struct pwm_state state = {
.period = PERIOD,
.duty_cycle = DUTY_LITTLE,
.polarity = PWM_POLARITY_NORMAL,
.enabled = true,
};
pwm_apply_state(mypwm, &state);
...
state.duty_cycle = PERIOD / 2;
pwm_apply_state(mypwm, &state);
For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.
So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The pwm-fsl-ftm driver is one of only three PWM drivers which updates
the state for the caller of pwm_apply_state(). This might have
surprising results if the caller reuses the values expecting them to
still represent the same state.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The pwm-sun4i driver is one of only three PWM drivers which updates the
state for the caller of pwm_apply_state(). This might have surprising
results if the caller reuses the values expecting them to still
represent the same state.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The pwm-rockchip driver is one of only three PWM drivers which updates
the state for the caller of pwm_apply_state(). This might have
surprising results if the caller reuses the values expecting them to
still represent the same state.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When pwm_apply_state() is called the lowlevel driver usually has to
apply some rounding because the hardware doesn't support nanosecond
resolution. So let pwm_get_state() return the actually implemented state
instead of the last applied one if possible.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm->chip is dereferenced several times in the pwm_apply_state()
function. Introducing a local variable for it helps keeping some lines a
bit shorter.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Don't rely on *state being zero initialized and PWM_POLARITY_NORMAL
being zero. So always assign .polarity.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This suppresses error messages in case the PWM clock isn't ready yet.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The range check for period_ns was written under assumption of a fixed
PWM clock. With clk-bcm2835 driver the PWM clock is a dynamic one.
So fix this by doing the range check on the period register value.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM config can be triggered via sysfs, so we better suppress the
error message in case of an invalid period to avoid kernel log spamming.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the rcar_pwm_apply() has already checked whether state->enabled
is set or not, this patch removes a redundant condition.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch adds the Spreadtrum PWM support, which provides maximum 4
channels.
Signed-off-by: Neo Hou <neo.hou@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add the compatible and the platform data to support PWM on the MT8516
SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The JZ4740 PWM implementation doesn't fulfill the (up to now
insufficiently documented) requirements of the PWM API. At least
document them in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 4a6ef8e37c ("pwm: Add support referencing PWMs from ACPI")
made pwm_get unconditionally return the acpi_pwm_get return value if
the device passed to pwm_get has an ACPI fwnode.
But even if the passed in device has an ACPI fwnode, it does not
necessarily have the necessary ACPI package defining its pwm bindings,
especially since the binding / API of this ACPI package has only been
introduced very recently.
Up until now X86/ACPI devices which use a separate pwm controller for
controlling their LCD screen's backlight brightness have been relying
on the static lookup-list to get their pwm.
pwm_get unconditionally returning the acpi_pwm_get return value breaks
this, breaking backlight control on these devices.
This commit fixes this by making pwm_get fall back to the static
lookup-list if acpi_pwm_get returns -ENOENT.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=96571
Reported-by: youling257@gmail.com
Fixes: 4a6ef8e37c ("pwm: Add support referencing PWMs from ACPI")
Cc: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This set of changes contains a new driver for SiFive SoCs as well as
enhancements to the core (device links are used to track dependencies
between PWM providers and consumers, support for PWM controllers via
ACPI, sysfs will now suspend/resume PWMs that it has claimed) and
various existing drivers.
-----BEGIN PGP SIGNATURE-----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=nseo
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes contains a new driver for SiFive SoCs as well as
enhancements to the core (device links are used to track dependencies
between PWM providers and consumers, support for PWM controllers via
ACPI, sysfs will now suspend/resume PWMs that it has claimed) and
various existing drivers"
* tag 'pwm/for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: fsl-ftm: Make sure to unlock mutex on failure
pwm: fsl-ftm: Use write protection for prescaler & polarity
pwm: fsl-ftm: More relaxed permissions for updating period
pwm: atmel-hlcdc: Add compatible for SAM9X60 HLCDC's PWM
pwm: bcm2835: Improve precision of PWM
leds: pwm: Support ACPI via firmware-node framework
pwm: Add support referencing PWMs from ACPI
pwm: rcar: Remove suspend/resume support
pwm: sysfs: Add suspend/resume support
pwm: Add power management descriptions
pwm: meson: Add documentation to the driver
pwm: meson: Add support PWM_POLARITY_INVERSED when disabling
pwm: meson: Don't cache struct pwm_state internally
pwm: meson: Read the full hardware state in meson_pwm_get_state()
pwm: meson: Simplify the calculation of the pre-divider and count
pwm: meson: Move pwm_set_chip_data() to meson_pwm_request()
pwm: meson: Add the per-channel register offsets and bits in a struct
pwm: meson: Add the meson_pwm_channel data to struct meson_pwm
pwm: meson: Pass struct pwm_device to meson_pwm_calc()
pwm: meson: Don't duplicate the polarity internally
...
Upon failure to enable clocks while trying to enable the PWM, make sure
to unlock the mutex that was taken to avoid a deadlock during subsequent
operations.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Rayagonda Kokatanur