[ Upstream commit 7cf4df30a9 ]
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f19c3f6c81 ]
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbd7814bb ]
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c6b9e95dde upstream.
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdf16d7894 upstream.
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89efbe70b2 upstream.
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ff ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27afac93e3 upstream.
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f1 ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f1 ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c6c378b0c upstream.
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8d1653dae upstream.
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
[1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3
Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce684552a2 upstream.
syzbot is reporting general protection fault in do_con_write() [1] caused
by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0
caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by
fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for
gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate()
from con_install() from tty_init_dev() from tty_open() on such console
causes vc->vc_pos == 0x10000000e due to
((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1).
I don't think that a console with 0 column or 0 row makes sense. And it
seems that vc_do_resize() does not intend to allow resizing a console to
0 column or 0 row due to
new_cols = (cols ? cols : vc->vc_cols);
new_rows = (lines ? lines : vc->vc_rows);
exception.
Theoretically, cols and rows can be any range as long as
0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g.
cols == 1048576 && rows == 2 is possible) because of
vc->vc_size_row = vc->vc_cols << 1;
vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row;
in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate().
Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in
visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return
an error, and con_write() will not be called on a console with 0 column
or 0 row.
We need to make sure that integer overflow in visual_init() won't happen.
Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying
1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate()
will be practically fine.
This patch does not touch con_init(), for returning -EINVAL there
does not help when we are not returning -ENOMEM.
[1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8
Reported-and-tested-by: syzbot <syzbot+017265e8553724e514e8@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200712111013.11881-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 551e553f0d upstream.
Commit 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064e ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b374c562ee upstream.
Commit 33ae787b74 ("serial: tegra: add support to ignore read") added
support for dropping input in case CREAD isn't set, but for PIO the
ignore_status_mask wasn't checked until after the character had been
put in the receive buffer.
Note that the NULL tty-port test is bogus and will be removed by a
follow-on patch.
Fixes: 33ae787b74 ("serial: tegra: add support to ignore read")
Cc: stable <stable@vger.kernel.org> # 5.4
Cc: Shardar Shariff Md <smohammed@nvidia.com>
Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22a82fa7d6 upstream.
The problems started with the revert (18cc7ac8a2). The
cdns_uart_console.index is statically assigned -1. When the port is
registered, Linux assigns consecutive numbers to it. It turned out that
when using ttyPS1 as console, the index is not updated as we are reusing
the same cdns_uart_console instance for multiple ports. When registering
ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it
already is 0 and not updated.
That led to 2ae11c46d5. It assigns the index prior to registering
the uart_driver once. Unfortunately, that ended up breaking the
situation where the probe order does not match the id order. When using
the same device tree for both uboot and linux, it is important that the
serial0 alias points to the console. So some boards reverse those
aliases. This was reported by Jan Kiszka. The proposed fix was reverting
the index assignment and going back to the previous iteration.
However such a reversed assignement (serial0 -> uart1, serial1 -> uart0)
was already partially broken by the revert (18cc7ac8a2). While the
ttyPS device works, the kmsg connection is already broken and kernel
messages go missing. Reverting the id assignment does not fix this.
>From the xilinx_uartps driver pov (after reverting the refactoring
commits), there can be only one console. This manifests in static
variables console_pprt and cdns_uart_console. These variables are not
properly linked and can go out of sync. The cdns_uart_console.index is
important for uart_add_one_port. We call that function for each port -
one of which hopefully is the console. If it isn't, the CON_ENABLED flag
is not set and console_port is cleared. The next cdns_uart_probe call
then tries to register the next port using that same cdns_uart_console.
It is important that console_port and cdns_uart_console (and its index
in particular) stay in sync. The index assignment implemented by
Shubhrajyoti Datta is correct in principle. It just may have to happen a
second time if the first cdns_uart_probe call didn't encounter the
console device. And we shouldn't change the index once the console uart
is registered.
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Fixes: 76ed2e1057 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fdbe136ae ]
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8edf8eb5f upstream.
This driver calls ioremap() in probe, but it misses calling iounmap() in
probe's error handler and remove.
Add the missed calls to fix it.
Fixes: 47d37d6f94 ("serial: Add auart driver for i.MX23/28")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200709135608.68290-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76ed2e1057 upstream.
This reverts commit 2ae11c46d5.
It turned out to break the ultra96-rev1, e.g., which uses uart1 as
serial0 (and stdout-path = "serial0:115200n8").
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf9c94456e upstream.
This reverts commit e2bd1dcbe1.
In discussion on the mailing list, it has been determined that this is
not the correct type of fix for this issue. Revert it so that we can do
this correctly.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Cc: Raghavendra Rao Ananta <rananta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4dd31f1ffe ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84d6f81c1f ]
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8508f4cba3 ]
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2bd1dcbe1 ]
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b668c064e ]
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e0a851fe6b upstream.
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a.
Fixes: 835d844d1a ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68e55f61c1 ]
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24eb2377f9 upstream.
hvc_open sets tty->driver_data to NULL when open fails at some point.
Typically, the failure happens in hp->ops->notifier_add(). If there is
a racing process which tries to open such mangled tty, which was not
closed yet, the process will crash in hvc_open as tty->driver_data is
NULL.
All this happens because close wants to know whether open failed or not.
But ->open should not NULL this and other tty fields for ->close to be
happy. ->open should call tty_port_set_initialized(true) and close
should check by tty_port_initialized() instead. So do this properly in
this driver.
So this patch removes these from ->open:
* tty_port_tty_set(&hp->port, NULL). This happens on last close.
* tty->driver_data = NULL. Dtto.
* tty_port_put(&hp->port). This happens in shutdown and until now, this
must have been causing a reference underflow, if I am not missing
something.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Raghavendra <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200526145632.13879-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b86dab0540 upstream.
When k_ascii is invoked several times in a row there is a potential for
signed integer overflow:
UBSAN: Undefined behaviour in drivers/tty/vt/keyboard.c:888:19 signed integer overflow:
10 * 1111111111 cannot be represented in type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.11 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
ubsan_epilogue+0xe/0x30 lib/ubsan.c:154
handle_overflow+0xdc/0xf0 lib/ubsan.c:184
__ubsan_handle_mul_overflow+0x2a/0x40 lib/ubsan.c:205
k_ascii+0xbf/0xd0 drivers/tty/vt/keyboard.c:888
kbd_keycode drivers/tty/vt/keyboard.c:1477 [inline]
kbd_event+0x888/0x3be0 drivers/tty/vt/keyboard.c:1495
While it can be worked around by using check_mul_overflow()/
check_add_overflow(), it is better to introduce a separate flag to
signal that number pad is being used to compose a symbol, and
change type of the accumulator from signed to unsigned, thus
avoiding undefined behavior when it overflows.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200525232740.GA262061@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17b4efdf4e upstream.
An uninitialised spin lock for sifive serial console raises a bad
magic spin_lock error as reported and discussed here [1].
Initialising the spin lock resolves the issue.
The fix is tested on HiFive Unleashed A00 board with Linux 5.7-rc4
and OpenSBI v0.7
[1] https://lore.kernel.org/linux-riscv/b9fe49483a903f404e7acc15a6efbef756db28ae.camel@wdc.com
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1589019852-21505-2-git-send-email-sagar.kadam@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ae11c46d5 ]
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57d38f26d8 ]
By directly using kfree() in different places we risk missing one if
it is switched to using vfree(), especially if the corresponding
vmalloc() is hidden away within a common abstraction.
Oh wait, that's exactly what happened here.
So let's fix this by creating a common abstraction for the free case
as well.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-by: syzbot+0bfda3ade1ee9288a1be@syzkaller.appspotmail.com
Fixes: 9a98e7a80f ("vt: don't use kmalloc() for the unicode screen buffer")
Cc: <stable@vger.kernel.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2005021043110.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3dc4db3662 upstream.
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a98e7a80f upstream.
Even if the actual screen size is bounded in vc_do_resize(), the unicode
buffer is still a little more than twice the size of the glyph buffer
and may exceed MAX_ORDER down the kmalloc() path. This can be triggered
from user space.
Since there is no point having a physically contiguous buffer here,
let's avoid the above issue as well as reducing pressure on high order
allocations by using vmalloc() instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003282214210.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2717769e20 upstream.
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c6 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7127d24372 upstream.
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abf42d2f33 upstream.
commit 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
breaks the UART on Cubieboard7-lite (based on S700 SoC), This is due to the
fact that generic clk routine clk_disable_unused() disables the gate clks,
and that in turns disables OWL UART (but UART driver never enables it). To
prove this theory, Andre suggested to use "clk_ignore_unused" in kernel
commnd line and it worked (Kernel happily lands into RAMFS world :)).
This commit fix this up by adding clk_prepare_enable().
Fixes: 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587067917-1400-1-git-send-email-amittomer25@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vignesh Raghavendra