commit fe634a7a9a upstream.
The clock setup on Meson8 cannot achieve a Mali frequency of exactly
182.15MHz. The vendor driver uses "FCLK_DIV7 / 2" for this frequency,
which translates to 2550MHz / 7 / 2 = 182142857Hz.
Update the GPU operating point to that specific frequency to not confuse
myself when comparing the frequency from the .dts with the actual clock
rate on the system.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46c9585ed4 upstream.
The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.
Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
#define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
#define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
#define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
#define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)
Meson8b additionally has these three registers:
#define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
#define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
#define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)
Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).
The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.
Fixes: 4a5a27116b ("ARM: dts: meson8: add support for booting the secondary CPU cores")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM Mali
GPU devices added to device trees, since the DRM drivers have now been
merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Polish and fixes for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now at
feature parity with TX1
-----BEGIN PGP SIGNATURE-----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=sHZs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM
Mali GPU devices added to device trees, since the DRM drivers have now
been merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Fixes and polish for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now
at feature parity with TX1"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits)
ARM: dts: gemini: Set DIR-685 SPI CS as active low
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
arm64: dts: qcom: qcs404: Add missing space for cooling-cells property
arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire
arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs
arm64: dts: rockchip: enable rk3328 watchdog clock
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
arm64: dts: rockchip: Add support for Hugsun X99 TV Box
arm64: dts: rockchip: Define values for the IPA governor for rock960
arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi
arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs
arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance.
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
arm64: dts: qcom: sdm845-cheza: add initial cheza dt
ARM: dts: msm8974-FP2: Add vibration motor
...
While the text specifies "of the GPL or the X11 license" the actual
license text matches the MIT license as specified at [0]
[0] https://spdx.org/licenses/MIT.html
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the canvas module to Meson8 because it's required for the VPU
(video output) and video decoders.
The canvas module is located inside thie "DMC bus" (where also some of
the memory controller registers are located). The "DMC bus" itself is
part of the so-called "MMC bus".
Amlogic's vendor kernel has an explicit #define for the "DMC" register
range on Meson8m2 while there's no such #define for Meson8. However, the
canvas and memory controller registers on Meson8 are all expressed as
"0x6000 + actual offset", while Meson8m2 uses "DMC + actual offset".
Thus it's safe to assume that the DMC bus exists on both SoCs even
though the registers inside are slightly different.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The interrupts in Amlogic's vendor kernel sources are all contiguous.
There are two typos leading to pp2 and pp4 as well as ppmmu2 and ppmmu4
incorrectly sharing the same interrupt line.
Fix this by using interrupt 170 for pp2 and 171 for ppmmu2.
Also drop the undocumented "switch-delay" which is a left-over from my
experiments with an early lima kernel driver when it was still
out-of-tree and required this property on Amlogic SoCs.
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 32-bit Meson SoCs have an RTC block in the AO (always on) area. The
RTC requires an external 32.768 kHz oscillator to work properly. Whether
or not this crystal exists depends on the board, so it has to be added
for each board.dts (instead of adding it somewhere in a generic .dtsi).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson8 SoC has an internal clock measurer IP which allows
measuring frequencies of various clock paths.
Enable it on meson8.dtsi so we can use it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SAR ADC can measure the chip temperature of the SoC. This only
works if the chip is calibrated and if the calibration data is written
to the correct registers. The calibration data is stored in the upper
two bytes of eFuse offset 0x1f4.
This adds the eFuse cell for the temperature calibration data and
passes it to the SAR ADC. We also need to pass the HHI sysctrl node to
the SAR ADC because the 4th TSC (temperature sensor calibration
coefficient) bit is stored in the HHI region (unlike bits [3:0] which
are stored directly inside the SAR ADC's register area).
On boards that have the SAR ADC enabled channel 8 can be used to
measure the chip temperature.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller on Meson8/Meson8m2 and Meson8b is part of a
register region called "HHI". This register area contains more
functionality than just a clock controller:
- the clock controller
- some reset controller bits
- temperature sensor calibration data (on Meson8b and Meson8m2 only)
- HDMI controller
Allow access to this HHI register area as "system controller". Also
migrate the Meson8 and Meson8b clock controllers to this new node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the Mali-450 GPU and it's OPP table for the Meson8 and Meson8m2 (the
latter inherits meson8.dtsi).
These SoCs have a Mali-450 GPU with six pixel processors. The OPP table
is taken from the 3.10 vendor kernel which uses the following table:
FCLK_DEV7 | 1, /* 182.1 Mhz */
FCLK_DEV4 | 1, /* 318.7 Mhz */
FCLK_DEV3 | 1, /* 425 Mhz */
FCLK_DEV5 | 0, /* 510 Mhz */
FCLK_DEV4 | 0, /* 637.5 Mhz */
This describes the mux (FCLK_DEVx) and a 0-based divider in the clock
controller. "FCLK" is "fixed_pll" which is running at 2550MHz.
The "turbo" setting is described by "turbo_clock = 4" where 4 is the
index of the table above.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Various peripherals (Mali GPU, NAND controller, VPU, etc.) are located
in the APB bus. Describe this bus so we can add devices to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The values are taken from Amlogic's 3.10 kernel sources. Their sources
have a "meson8m2_n200_2G.dtd" which defines a different voltage table:
- 0.86V for 96MHz
- (values in between omitted)
- 1.14V for 1.992GHz
The reason for this is simply the hardware design because the voltage
regulator on this board is has a minimum output of 0.86V and a maximum
output of 1.14V. The recommended settings are added with this patch
instead of using the values that are only valid for one board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoCs are using four Cortex-A9 cores. These come
with an ARM global timer.
This adds the Cortex-A9 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoC are using four ARM Cortex-A9 cores which
come with a "TWD" (Timer-Watchdog) based timer. This adds support for
the ARM TWD Timer on these two SoCs.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The public Meson8b (S805) datasheet describes a memory region called "A9
Periph base" which starts at 0xC4300000 and ends at 0xC430FFFF. Add a
simple-bus node and move all peripherals that are part of this memory
region.
This makes the .dts a bit easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson Timer IP block has two clock inputs:
- clk81 for using the system clock as timebase
- xtal for a timebase with 1us, 10us, 100us and 1ms resolution
The clocksource driver does not use these yet, but it's still a good
idea to add them as this describes how the hardware actually works
internally.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 2c323c43a3 ("ARM: dts: meson8: add and use the real clock controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the pins for uart_A, which is used to connect to the Bluetooth
module on some devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the performance monitor unit on Meson8.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that we support the reset controller on Meson8 we can add the reset
line to the USB PHYs (just like on Meson8b).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson8 uses the same reset controller as Meson8b. Add the node along
with the #include for the reset lines to meson8.dtsi so we can use it
from there as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This enables the GPIO interrupt controller for the Meson8 SoCs.
Interrupt support on the GPIOs can be used by the MMC framework to
detect when an SD card is inserted/removed or by the input framework to
detect button presses.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch to the stable UART bindings and add the correct gate clocks
to the non-AO UART nodes.
This fixes the non-AO UARTs if the bootloader didn't un-gate the clocks.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SAR ADC modules doesn't require The "sana" clock.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic's vendor kernel prints these PL310 L2 cache controller settings
during boot:
8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
Add the "prefetch-data", "prefetch-instr" and "arm,shared-override"
properties to get the same L2 cache controller configuration as the
vendor kernel.
Two differences still remain:
- L310_AUX_CTRL_NS_INT_CTRL is currently not supported by the cache-l2x0
driver
- bit 23 is set by the vendor kernel, but this is defined in cache-l2x0.h
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson6, Meson8 and Meson8b use a similar IP block which has access to
512 bytes of efuse data.
During SoC manufacturing some calibration settings for the CVBS
connector and the internal temperature sensor are written to this efuse.
On some boards it additionally stores for example the MAC addresses.
The efuse is enabled on Meson8 and Meson8b but kept disabled on Meson6
since we do not have a clock driver there (which is required to read
data from the efuse).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Booting the secondary CPU cores involves the following nodes/devices:
- SCU (Snoop-Control-Unit, for which we already have a DT node)
- a reset line for each CPU core, provided by the reset-controller
which is built into the clock-controller
- the PMU (power management unit) which controls the power of the CPU
cores
- a range in the SRAM specifically reserved for booting secondary CPU
cores
- the "enable-method" which activates booting the secondary CPU cores
This adds all required nodes and properties to boot the secondary CPU
cores.
Suggested-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson6, Meson8 and Meson8b are using the same MMC controller IP. This
adds the MMC controller node to meson.dtsi so it can be used by all
SoCs.
The controller itself is a bit special, because it has multiple slots.
Each slot is accessed through a sub-node of the controller. However,
currently the driver for this hardware only supports one slot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove pin offset on the AO controller. meson pinctrl no longer has
this quirk
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SoC type and version information is encoded in different register
blocks.
The SoC type information is part of the "assist" registers.
The misc version information is part of the "bootrom" registers.
On Meson8, Meson8b and Meson8m2 there is additionally information about
the minor version. This information is stored in the "analog top"
registers.
Add the nodes for these register blocks so we can decode the SoC type
and version information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller provides a few reset lines as well. Add the
corresponding CPU cores.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
pwm_ab and pwm_cd are already inherited from meson.dtsi, we only need to
define the correct "compatible" string so the pwm-meson driver can
choose the parent clocks correctly.
pwm_ef is added to meson8.dtsi directly (similar to how it's done in
meson8b.dtsi) as this controller only exists on Meson8 and Meson8b.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Until now clk81 was used as gate clock for the ethernet controller on
Meson8 whereas Meson8b did not configure a gate clock at all. Use
CLKID_ETH for both SoCs, which is the real gate clock for the ethernet
controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic's Meson8b SoC has a Snoop Control Unit (SCU), just like many
other Cortex-A5 SoCs. Add the corresponding devicetree node so it can be
used during SMP boot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the DWC2 USB controller nodes and the corresponding USB2 PHY
nodes to meson.dtsi (as the same - or at least a very similar) IP block
is used on all SoCs (at the same physical address).
Additionally meson8.dtsi and meson8b.dtsi add the required clocks to the
DWC2 and USB2 PHY nodes, otherwise the DWC2 controller cannot be
initialized by the dwc2 driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All supported Meson SoCs have a random number generator in CBUS.
Newer SoCs (GXBB, GXL and GXM) provide only one 32-bit random number
register, whereas the older SoCs (Meson6, Meson8 and Meson8b) have two
32-bit random number registers. The existing meson-rng driver only
supports the lower 32-bit - but it still works fine on the older SoCs
apart from this small limitation.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There seem to be two memory regions that need to be reserved, otherwise
the system just hangs when running:
$ stress --vm-bytes $(awk '/MemFree/{printf "%d\n", $2 * 0.9;}' < /proc/meminfo)k \
--vm-keep -m 1
The first memory region is really crucial and without it the system
hangs. I could not find any references to this in Amlogic's GPL kernel
sources.
The second region is used by the "suspend firmware". The u-boot sources
(/arch/arm/cpu/aml_meson/m8/firmwareld.c) state that the suspend
firmware is located at "64M + 15M" which matches CONFIG_MESON_SUSPEND in
the Amlogic GPL kernel sources. The "suspend firmware" is responsible
for waking up the system from suspend state.
This also fixes reading the full SD card as without this the system
would simply hang (probably related to the first memory region, if some
buffer is allocated there).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the SAR ADC to meson.dtsi and configures the clocks on Meson8
and Meson8b to allow boards to use it. Some boards use it to connect a
button to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the definition of the PWM_E (CBUS) and PWM_F (AOBUS) to
meson8.dtsi, allowing devices to use them. PWM_E can be used on some
devices to generate the 32.768kHz clock for the SDIO wifi module, while
PWM_F can be used to control the power LED.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This replaces the "/include/" syntax with the "#include" syntax in all
Amlogic Meson .dts and .dtsi files. That is required to use preprocessor
defines (like GIC_SPI and IRQ_TYPE_EDGE_RISING) in meson.dtsi (all files
which directly or indirectly include meson.dtsi need to use the
"#include" syntax, otherwise the .dts files cannot be compiled).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The IR receiver pins are currently defined in the CBUS pin-controller.
However the pins are in the AO region, which is controlled by the AOBUS
pin-controller. Move the pins to pinctrl_aobus so they can actually be
used.
Fixes: b60e1157d8 ("ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This removes the dummy clk81 gate and replaces it with the actual clock
controller's CLKID_CLK81. This will also allow us to pass the real clock
IDs to all devices where the clock is controlled by clkc in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch extends the L2 cache controller node for the Amlogic Meson8
and Meson8b SoCs with some missing parameters. These are taken from the
Amlogic GPL kernel source.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[apply the change to Meson8 and Meson8b and updated description]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson SoCs have most of the internal peripherals organized
in busses. Use them to make the dts easier to read and to avoid
duplicated register (bus) offset definitions.
The bus information is taken from the vendor kernel:
#define IO_CBUS_PHY_BASE 0xc1100000 ///2M
#define IO_AOBUS_PHY_BASE 0xc8100000 ///1M
There are more internal busses (such as the abp bus which seems to
contain audio, HDMI and Mali registers), but since we don't have
drivers for them yet these are not added (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl