Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes: c83b8fab06 ("bridge: Restart queries when last querier expires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce says:
====================
Fix thunderx MTU with XDP
The thunderx driver can't use XDP with all MTU values.
This patches sets the right MTU values, and add a check to avoid setting
a wrong value which will not function.
v3: Fix a copy-paste from two functions, tested on proper hardware:
2: enP2p1s0v0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 1c:1b:0d:0d:52:a4 brd ff:ff:ff:ff:ff:ff
[ 787.019730] nicvf 0002:01:00.1 enP2p1s0v0: Jumbo frames not yet supported with XDP, current MTU 1800.
RTNETLINK answers: Operation not supported
[ 800.574568] nicvf 0002:01:00.1 enP2p1s0v0: Link is Up 10000 Mbps Full duplex
[ 807.248321] nicvf 0002:01:00.1 enP2p1s0v0: Jumbo frames not yet supported with XDP, current MTU 1500.
RTNETLINK answers: Invalid argument
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: fixes 2019-04-11
here are some fixes in different areas of the smc code for the net
tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit <26d92e951fe0>
("net/smc: move unhash as early as possible in smc_release()")
fixes one occurrence in the smc code, but the same pattern exists
in other places. This patch covers the remaining occurrences and
makes sure, the unhash operation is done before the smc->clcsock is
released. This avoids a potential use-after-free in smc_diag_dump().
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLUSH command is used to empty the pnet table. No return code is
expected from the command. Commit a9d8b0b1e3d6 added namespace support
for the pnet table and changed the FLUSH command processing to call
smc_pnet_remove_by_pnetid() to remove the pnet entries. This function
returns -ENOENT when no entry was deleted, which is now the return code
of the FLUSH command. As a result the FLUSH command will return an error
when the pnet table is already empty.
Restore the expected behavior and let FLUSH always return 0.
Fixes: a9d8b0b1e3d6 ("net/smc: add pnet table namespace support")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fcntl(fd, F_SETOWN, getpid()) selects the recipient of SIGURG signals
that are delivered when out-of-band data arrives on socket fd.
If an SMC socket program makes use of such an fcntl() call, it fails
in case of fallback to TCP-mode. In case of fallback the traffic is
processed with the internal TCP socket. Propagating field "file" from the
SMC socket to the internal TCP socket fixes the issue.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case alloc_ordered_workqueue fails, the fix returns NULL
to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the clcsock is already released using sock_release() and a pending
smc_listen_work accesses the clcsock than that will fail. Solve this
by canceling and waiting for the work to complete first. Because the
work holds the sock_lock it must make sure that the lock is not hold
before the new helper smc_clcsock_release() is invoked. And before the
smc_listen_work starts working check if the parent listen socket is
still valid, otherwise stop the work early.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gue tunnels run iptunnel_pull_offloads on received skbs. This can
determine a possible use-after-free accessing guehdr pointer since
the packet will be 'uncloned' running pskb_expand_head if it is a
cloned gso skb (e.g if the packet has been sent though a veth device)
Fixes: a09a4c8dd1 ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When binding multiple services with specific type 1Ki, 2Ki..,
this leads to some entries in the name table of publications
missing when listed out via 'tipc name show'.
The problem is at identify zero last_type conditional provided
via netlink. The first is initial 'type' when starting name table
dummping. The second is continuously with zero type (node state
service type). Then, lookup function failure to finding node state
service type in next iteration.
To solve this, adding more conditional to marked as dirty type and
lookup correct service type for the next iteration instead of select
the first service as initial 'type' zero.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to accept zero size iova range which will lead a infinite loop
in translate_desc(). Fixing this by failing the request in this case.
Reported-by: syzbot+d21e6e297322a900c128@syzkaller.appspotmail.com
Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike '&&' operator, the '&' does not have short-circuit
evaluation semantics. IOW both sides of the operator always
get evaluated. Fix the wrong operator in
tls_is_sk_tx_device_offloaded(), which would lead to
out-of-bounds access for for non-full sockets.
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev appears through hot plug then gets enslaved by a failover
master that is already up and running, the slave will be opened
right away after getting enslaved. Today there's a race that userspace
(udev) may fail to rename the slave if the kernel (net_failover)
opens the slave earlier than when the userspace rename happens.
Unlike bond or team, the primary slave of failover can't be renamed by
userspace ahead of time, since the kernel initiated auto-enslavement is
unable to, or rather, is never meant to be synchronized with the rename
request from userspace.
As the failover slave interfaces are not designed to be operated
directly by userspace apps: IP configuration, filter rules with
regard to network traffic passing and etc., should all be done on master
interface. In general, userspace apps only care about the
name of master interface, while slave names are less important as long
as admin users can see reliable names that may carry
other information describing the netdev. For e.g., they can infer that
"ens3nsby" is a standby slave of "ens3", while for a
name like "eth0" they can't tell which master it belongs to.
Historically the name of IFF_UP interface can't be changed because
there might be admin script or management software that is already
relying on such behavior and assumes that the slave name can't be
changed once UP. But failover is special: with the in-kernel
auto-enslavement mechanism, the userspace expectation for device
enumeration and bring-up order is already broken. Previously initramfs
and various userspace config tools were modified to bypass failover
slaves because of auto-enslavement and duplicate MAC address. Similarly,
in case that users care about seeing reliable slave name, the new type
of failover slaves needs to be taken care of specifically in userspace
anyway.
It's less risky to lift up the rename restriction on failover slave
which is already UP. Although it's possible this change may potentially
break userspace component (most likely configuration scripts or
management software) that assumes slave name can't be changed while
UP, it's relatively a limited and controllable set among all userspace
components, which can be fixed specifically to listen for the rename
events on failover slaves. Userspace component interacting with slaves
is expected to be changed to operate on failover master interface
instead, as the failover slave is dynamic in nature which may come and
go at any point. The goal is to make the role of failover slaves less
relevant, and userspace components should only deal with failover master
in the long run.
Fixes: 30c8bd5aa8 ("net: Introduce generic failover module")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding a team interface to bridge, the team interface will enter
promisc mode. Then if we add a new slave to team0, the slave will keep
promisc off. Fix it by setting slave to promisc on if team master is
already in promisc mode, also do the same for allmulti.
v2: add promisc and allmulti checking when delete ports
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
buildbot noticed that TLS_HW is not defined if CONFIG_TLS_DEVICE=n.
Wrap the cleanup branch into an ifdef, tls_device_free_resources_tx()
wouldn't be compiled either in this case.
Fixes: 35b71a34ad ("net/tls: don't leak partially sent record in device mode")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: tls: fix memory leaks and freeing skbs
This series fixes two memory issues and a stack overflow.
First two patches are fairly simple leaks. Third patch
partially reverts an optimization made to the strparser
which causes creation of skb->frag_list->skb->frag_list...
chains of 100s of skbs, leading to recursive kfree_skb()
filling up the kernel stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the first part of commit 4e485d06bb ("strparser: Call
skb_unclone conditionally"). To build a message with multiple
fragments we need our own root of frag_list. We can't simply
use the frag_list of orig_skb, because it will lead to linking
all orig_skbs together creating very long frag chains, and causing
stack overflow on kfree_skb() (which is called recursively on
the frag_lists).
BUG: stack guard page was hit at 00000000d40fad41 (stack is 0000000029dde9f4..000000008cce03d5)
kernel stack overflow (double-fault): 0000 [#1] PREEMPT SMP
RIP: 0010:free_one_page+0x2b/0x490
Call Trace:
__free_pages_ok+0x143/0x2c0
skb_release_data+0x8e/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
[...]
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
__kfree_skb+0xe/0x20
tcp_disconnect+0xd6/0x4d0
tcp_close+0xf4/0x430
? tcp_check_oom+0xf0/0xf0
tls_sk_proto_close+0xe4/0x1e0 [tls]
inet_release+0x36/0x60
__sock_release+0x37/0xa0
sock_close+0x11/0x20
__fput+0xa2/0x1d0
task_work_run+0x89/0xb0
exit_to_usermode_loop+0x9a/0xa0
do_syscall_64+0xc0/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Let's leave the second unclone conditional, as I'm not entirely
sure what is its purpose :)
Fixes: 4e485d06bb ("strparser: Call skb_unclone conditionally")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reports that tls triggers warnings related to
sk->sk_forward_alloc not being zero at destruction time:
WARNING: CPU: 5 PID: 6831 at net/core/stream.c:206 sk_stream_kill_queues+0x103/0x110
WARNING: CPU: 5 PID: 6831 at net/ipv4/af_inet.c:160 inet_sock_destruct+0x15b/0x170
When sender fills up the write buffer and dies from
SIGPIPE. This is due to the device implementation
not cleaning up the partially_sent_record.
This is because commit a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
moved the partial record cleanup to the SW-only path.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f66de3ee2c ("net/tls: Split conf to rx + tx") made
freeing of IV and record sequence number conditional to SW
path only, but commit e8f6979981 ("net/tls: Add generic NIC
offload infrastructure") also allocates that state for the
device offload configuration. Remember to free it.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon says:
====================
ibmvnic: Fix netdev features settings on reset
In its current state, a driver reset clobbers any feature settings
a user may have toggled and will disable GRO as it is not explicitly
enabled in the driver. This patch set enables GRO and tries to retain
user settings after a reset. If the underlying carrier changes, however,
the driver will disable features unsupported by the new carrier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Various fixes
This patchset contains various small fixes for mlxsw.
Patch #1 fixes a warning generated by switchdev core when the driver
fails to insert an MDB entry in the commit phase.
Patches #2-#4 fix a warning in check_flush_dependency() that can be
triggered when a work item in a WQ_MEM_RECLAIM workqueue tries to flush
a non-WQ_MEM_RECLAIM workqueue.
It seems that the semantics of the WQ_MEM_RECLAIM flag are not very
clear [1] and that various patches have been sent to remove it from
various workqueues throughout the kernel [2][3][4] in order to silence
the warning.
These patches do the same for the workqueues created by mlxsw that
probably should not have been created with this flag in the first place.
Patch #5 fixes a regression where an IP address cannot be assigned to a
VRF upper due to erroneous MAC validation check. Patch #6 adds a test
case.
Patch #7 adjusts Spectrum-2 shared buffer configuration to be compatible
with Spectrum-1. The problem and fix are described in detail in the
commit message.
Please consider patches #1-#5 for 5.0.y. I verified they apply cleanly.
[1] https://patchwork.kernel.org/patch/10791315/
[2] Commit ce162bfbc0 ("mac80211_hwsim: don't use WQ_MEM_RECLAIM")
[3] Commit 39baf10310 ("IB/core: Fix use workqueue without WQ_MEM_RECLAIM")
[4] Commit 75215e5bb2 ("iwcm: Don't allocate iwcm workqueue with WQ_MEM_RECLAIM")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.
The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.
To work around this issue, commit e83c045e53 ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.
The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.
Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.
Fixes: fe099bf682 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that it is possible to set an IP address on a VRF and that it is
not vetoed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.
This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.
Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.
Fixes: 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e920 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.
Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.
Fixes: d965465b60 ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although XOR hash function can perform very well on some special use
cases, to align with all drivers, mlx5 driver should use Toeplitz hash
by default.
Toeplitz is more stable for the general use case and it is more standard
and reliable.
On top of that, since XOR (MLX5_RX_HASH_FN_INVERTED_XOR8) gives only a
repeated 8 bits pattern. When used for udp tunneling RSS source port
manipulation it results in fixed source port, which will cause bad RSS
spread.
Fixes: 2be6967cdb ("net/mlx5e: Support ETH_RSS_HASH_XOR")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit b820e6fb09.
Prior the commit we are reverting, checksum unnecessary was only set when
both the L3 OK and L4 OK bits are set on the CQE. This caused packets
of IP protocols such as SCTP which are not dealt by the current HW L4
parser (hence the L4 OK bit is not set, but the L4 header type none bit
is set) to go through the checksum none code, where currently we wrongly
report checksum unnecessary for them, a regression. Fix this by a revert.
Note that on our usual track we report checksum complete, so the revert
isn't expected to have any notable performance impact. Also, when we are
not on the checksum complete track, the L4 protocols for which we report
checksum none are not high performance ones, we will still report
checksum unnecessary for UDP/TCP.
Fixes: b820e6fb09 ("net/mlx5e: Enable reporting checksum unnecessary also for L3 packets")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Avi Urman <aviu@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
TC encap offload is supported only for the physical uplink
representor. Fail for non uplink representor.
Fixes: 3e621b19b0 ("net/mlx5e: Support TC encapsulation offloads with upper devices")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the two places is_last_ethertype_ip is being called, the caller will
be looking inside the ip header, to be safe, add ip{4,6} header sanity
check. And return true only on valid ip headers, i.e: the whole header
is contained in the linear part of the skb.
Note: Such situation is very rare and hard to reproduce, since mlx5e
allocates a large enough headroom to contain the largest header one can
imagine.
Fixes: fe1dc06999 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an ethernet frame with ip payload is padded, the padding octets are
not covered by the hardware checksum.
Prior to the cited commit, skb checksum was forced to be CHECKSUM_NONE
when padding is detected. After it, the kernel will try to trim the
padding bytes and subtract their checksum from skb->csum.
In this patch we fixup skb->csum for any ip packet with tail padding of
any size, if any padding found.
FCS case is just one special case of this general purpose patch, hence,
it is removed.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
XDP programs might change packets data contents which will make the
reported skb checksum (checksum complete) invalid.
When XDP programs are loaded/unloaded set/clear rx RQs
MLX5E_RQ_STATE_NO_CSUM_COMPLETE flag.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When requested to recover from error, the tx reporter might open new
channels and close the existing ones. Use safe channels switch flow in
order to guarantee opened channels at the end of the recover flow.
For this purpose, define mlx5e_safe_reopen_channels function and use it
within those flows.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Skip recover operation if interface is in down state as TX objects are
not open. This fixes a bug were the recover flow re-opened TX objects
which were not opened before, leading to a possible memory leak at
driver unload.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
Added synchronize_rcu before kfree(flow)
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To avoid use-after-free, hold the rcu read lock until we are done copying
flow data into the command buffer.
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
-----BEGIN PGP SIGNATURE-----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=2EV9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes:
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.
Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).
Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.
2) There have been many weird regressions in r8169 since we turned ASPM
support on, some are still not understood nor completely resolved.
Let's turn this back off for now. From Heiner Kallweit.
3) Signess fixes for ethtool speed value handling, from Michael
Zhivich.
4) Handle timestamps properly in macb driver, from Paul Thomas.
5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
and we're holding a stale protocol header pointer". From Lorenzo
Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnxt_en: Reset device on RX buffer errors.
bnxt_en: Improve RX consumer index validity check.
net: macb driver, check for SKBTX_HW_TSTAMP
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
net: ip_gre: fix possible use-after-free in erspan_rcv
r8169: disable ASPM again
MAINTAINERS: ieee802154: update documentation file pattern
net: vrf: Fix ping failed when vrf mtu is set to 0
selftests: add a tc matchall test case
nfc: nci: Potential off by one in ->pipes[] array
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
Pull TPM fixes from James Morris:
"From Jarkko: These are critical fixes for v5.1. Contains also couple
of new selftests for v5.1 features (partial reads in /dev/tpm0)"
* 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selftests/tpm2: Open tpm dev in unbuffered mode
selftests/tpm2: Extend tests to cover partial reads
KEYS: trusted: fix -Wvarags warning
tpm: Fix the type of the return value in calc_tpm2_event_size()
KEYS: trusted: allow trusted.ko to initialize w/o a TPM
tpm: fix an invalid condition in tpm_common_poll
tpm: turn on TPM on suspend for TPM 1.x
- fix syscall number passed to trace_sys_exit;
- fix syscall number initialization in start_thread;
- fix level interpretation in the return_address;
- fix format string warning in init_pmd.
-----BEGIN PGP SIGNATURE-----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=EzVN
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtensa fixes from Max Filippov:
- fix syscall number passed to trace_sys_exit
- fix syscall number initialization in start_thread
- fix level interpretation in the return_address
- fix format string warning in init_pmd
* tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix format string warning in init_pmd
xtensa: fix return_address
xtensa: fix initialization of pt_regs::syscall in start_thread
xtensa: use actual syscall number in do_syscall_trace_leave
Michael Chan says:
====================
bnxt_en: 2 bug fixes.
The first patch prevents possible driver crash if we get a bad RX index
from the hardware. The second patch resets the device when the hardware
reports buffer error to recover from the error.
Please queue these for -stable also. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Duan