Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:
[ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4
[ 233.602642] Hardware name: Google Scarlet (DT)
[ 233.602647] Call trace:
[ 233.602663] dump_backtrace+0x0/0x11c
[ 233.602672] show_stack+0x20/0x28
[ 233.602681] dump_stack+0x98/0xbc
[ 233.602690] ___might_sleep+0x154/0x16c
[ 233.602696] __might_sleep+0x78/0x88
[ 233.602704] mutex_lock+0x2c/0x5c
[ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[ 233.602757] net_rx_action+0x140/0x388
[ 233.602766] __do_softirq+0x1b0/0x35c
[...]
ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.
A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null
(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)
The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.
I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.
Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com
Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit fc3a2fcaa1 ("mwifiex: use atomic bitops to represent
adapter status variables") had a fairly straightforward bug in it. It
contained this bit of diff:
- if (!adapter->is_suspended) {
+ if (test_bit(MWIFIEX_IS_SUSPENDED, &adapter->work_flags)) {
As you can see the patch missed the "!" when converting to the atomic
bitops. This meant that the resume hasn't done anything at all since
that commit landed and suspend/resume for mwifiex SDIO cards has been
totally broken.
After fixing this mwifiex suspend/resume appears to work again, at
least with the simple testing I've done.
Fixes: fc3a2fcaa1 ("mwifiex: use atomic bitops to represent adapter status variables")
Cc: <stable@vger.kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Fix an oops when creating debugfs entries;
* Fix bug when trying to capture debugging info while in rfkill;
* Prevent potential uninitialized memory dumps into debugging logs;
* Fix some initialization parameters for AX210 devices;
* Fix an oops with non-MSIX devices;
-----BEGIN PGP SIGNATURE-----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=I1UT
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2019-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Third batch of iwlwifi fixes intended for v5.1
* Fix an oops when creating debugfs entries;
* Fix bug when trying to capture debugging info while in rfkill;
* Prevent potential uninitialized memory dumps into debugging logs;
* Fix some initialization parameters for AX210 devices;
* Fix an oops with non-MSIX devices;
Specifically, max_tfd_queue_size should be 0x10000 like in
22560 family and not 0x100 like in 22000 family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
debugfs can now report an error code if something went wrong instead of
just NULL. So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.
This is now happening because of ff9fb72bc0 ("debugfs: return error
values, not NULL"). If multiple iwlwifi devices are in the system, this
can cause problems when the driver attempts to create the main debugfs
directory again. Later on in the code we fail horribly by trying to
dereference a pointer that is an error value.
Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Gabriel Ramirez <gabriello.ramirez@gmail.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: stable <stable@vger.kernel.org> # 5.0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In ini debug TLVs bit 24 is set. The driver relies on it in the memory
allocation for the debug configuration. This implementation is
problematic in case of a new debug TLV that is not supported yet is added
and uses bit 24. In such a scenario the driver allocate space without
using it which causes errors in the apply point enabling flow.
Solve it by explicitly checking if a given TLV is part of the list of
the supported ini debug TLVs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f14cda6f3b ("iwlwifi: trans: parse and store debug ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we fail to initialize because rfkill is enabled, then trying
to do debug collection currently just fails. Prevent that in the
high-level code, although we should probably also fix the lower
level code to do things more carefully.
It's not 100% clear that it fixes this commit, as the original
dump code at the time might've been more careful. In any case,
we don't really need to dump anything in this expected scenario.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 7125648074 ("iwlwifi: add fw dump upon RT ucode start failure")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver uses msix causes-register to handle both msix and non msix
interrupts when performing sync nmi. On devices that do not support
msix this register is unmapped and accessing it causes a kernel panic.
Solve this by differentiating the two cases and accessing the proper
causes-register in each case.
Reported-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAINTAINERS contains a lower-case and upper-case variant of
Woojung Huh' s email address.
Only keep the lower-case variant in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bond is enslaved to another bond, bond_netdev_event() only
handles the event as if the bond is a master, and skips treating the
bond as a slave.
This leads to a refcount leak on the slave, since we don't remove the
adjacency to its master and the master holds a reference on the slave.
Reproducer:
ip link add bondL type bond
ip link add bondU type bond
ip link set bondL master bondU
ip link del bondL
No "Fixes:" tag, this code is older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for 5.1.
iwlwifi
* add some new PCI IDs (plus a struct name change they depend on)
* fix crypto with new devices, namely 22560 and above
* fix for a potential deadlock in the TX path
* a fix for offloaded rate-control
* support new PCI HW IDs which use a new FW
mt76
* fix lock initialisation and a possible deadlock
* aggregation fixes
rt2x00
* fix sequence numbering during retransmits
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJctIf2AAoJEG4XJFUm622bm4UH/RjizpPno79+PxKgZFxhYcWJ
4sBW1hDwcO4FNKLX3tf6WR4N/vxkPEWSbB1gGRbHAIeYeb74ab5hYQoCVaOnU8GL
uzhjgGVHwUnBi0oluuG12gpU9Zf6raV4Ec9HdRszx1A8DOa0qn5lUrXwWbF3GlZZ
BU4ojdOZOVQx+yqE+xIr7okcbBpxRZgLK7KthKWgR4G9RlISIsfMYAHE1fwPmPr8
b7fwqAKkgJ5fGSxez1tv7hlYaRw2zVwFYrVv3TegRKMl1pHTI/ps3ip37JTwv+O0
lv5112AgEO2cSPT/R0wWqEkZ21Rc/AeFbttcQ9Ejw1SPc/w2d+fX8pTY5/RPw8w=
=RCyH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-04-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
Second set of fixes for 5.1.
iwlwifi
* add some new PCI IDs (plus a struct name change they depend on)
* fix crypto with new devices, namely 22560 and above
* fix for a potential deadlock in the TX path
* a fix for offloaded rate-control
* support new PCI HW IDs which use a new FW
mt76
* fix lock initialisation and a possible deadlock
* aggregation fixes
rt2x00
* fix sequence numbering during retransmits
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcrPOfAAoJEEg/ir3gV/o+c1sIAIuVUmF95OK6BxrNxQ31HN7i
0V/OW29V6B5musqyGXVa90nl9wJ9BE2tmtHsg2HPABXdGdiYhNRP7Tm+aq+QYBe3
8kJVk5U+HCLeHvf9k3dpJZokMzAgEhuWAbuAE1YelYUtbOXO9Zrj2uTL1NHJTYyc
SNOg9+gATOMsOAuiUyygN0XMoYESTsUE7UH4tuhyYr44cKR85qOQDPAlcDEHGTfO
uHWwmOznZqFVJUVyfwtEkTojsxNiW+QA2PR5faX/+eI7746qXOAzYq2JSjtNEyTz
4xB9a+t47xpGDw4Svwu51pDw+4Uiiy1Yv0kOKKpBqrCk892bZ8l1gWcHRgjYx/8=
=9wkB
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-09
This series provides some fixes to mlx5 driver.
I've cc'ed some of the checksum fixes to Eric Dumazet and i would like to get
his feedback before you pull.
For -stable v4.19
('net/mlx5: FPGA, tls, idr remove on flow delete')
('net/mlx5: FPGA, tls, hold rcu read lock a bit longer')
For -stable v4.20
('net/mlx5e: Rx, Check ip headers sanity')
('Revert "net/mlx5e: Enable reporting checksum unnecessary also for L3 packets"')
('net/mlx5e: Rx, Fixup skb checksum for packets with tail padding')
For -stable v5.0
('net/mlx5e: Switch to Toeplitz RSS hash by default')
('net/mlx5e: Protect against non-uplink representor for encap')
('net/mlx5e: XDP, Avoid checksum complete when XDP prog is loaded')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub forgot to either use nlmsg_len() or nlmsg_msg_size(),
allowing KMSAN to detect a possible uninit-value in rtnl_stats_get
BUG: KMSAN: uninit-value in rtnl_stats_get+0x6d9/0x11d0 net/core/rtnetlink.c:4997
CPU: 0 PID: 10428 Comm: syz-executor034 Not tainted 5.1.0-rc2+ #24
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x131/0x2a0 mm/kmsan/kmsan.c:619
__msan_warning+0x7a/0xf0 mm/kmsan/kmsan_instr.c:310
rtnl_stats_get+0x6d9/0x11d0 net/core/rtnetlink.c:4997
rtnetlink_rcv_msg+0x115b/0x1550 net/core/rtnetlink.c:5192
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2485
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5210
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
___sys_sendmsg+0xdb3/0x1220 net/socket.c:2137
__sys_sendmsg net/socket.c:2175 [inline]
__do_sys_sendmsg net/socket.c:2184 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2182
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2182
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
Fixes: 51bc860d4a ("rtnetlink: stats: validate attributes in get as well as dumps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Bolotin says:
====================
qed: Fix the Doorbell Overflow Recovery mechanism
This patch series fixes and improves the doorbell recovery mechanism.
The main goals of this series are to fix missing attentions from the
doorbells block (DORQ) or not handling them properly, and execute the
recovery from periodic handler instead of the attention handler.
Please consider applying the series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recompile IP options since IPCB may not be valid anymore when
ipv4_link_failure is called from arp_error_report.
Refer to the commit 3da1ed7ac3 ("net: avoid use IPCB in cipso_v4_error")
and the commit before that (9ef6b42ad6) for a similar issue.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Fixes
Here is a collection of fixes for rxrpc:
(1) rxrpc_error_report() needs to call sock_error() to clear the error
code from the UDP transport socket, lest it be unexpectedly revisited
on the next kernel_sendmsg() call. This has been causing all sorts of
weird effects in AFS as the effects have typically been felt by the
wrong RxRPC call.
(2) Allow a kernel user of AF_RXRPC to easily detect if an rxrpc call has
completed.
(3) Allow errors incurred by attempting to transmit data through the UDP
socket to get back up the stack to AFS.
(4) Make AFS use (2) to abort the synchronous-mode call waiting loop if
the rxrpc-level call completed.
(5) Add a missing tracepoint case for tracing abort reception.
(6) Fix detection and handling of out-of-order ACKs.
====================
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rxrpc packet serial number cannot be safely used to compute out of
order ack packets for several reasons:
1. The allocation of serial numbers cannot be assumed to imply the order
by which acks are populated and transmitted. In some rxrpc
implementations, delayed acks and ping acks are transmitted
asynchronously to the receipt of data packets and so may be transmitted
out of order. As a result, they can race with idle acks.
2. Serial numbers are allocated by the rxrpc connection and not the call
and as such may wrap independently if multiple channels are in use.
In any case, what matters is whether the ack packet provides new
information relating to the bounds of the window (the firstPacket and
previousPacket in the ACK data).
Fix this by discarding packets that appear to wind back the window bounds
rather than on serial number procession.
Fixes: 298bc15b20 ("rxrpc: Only take the rwind and mtu values from latest ACK")
Signed-off-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace received calls that are aborted due to a connection abort, typically
because of authentication failure. Without this, connection aborts don't
show up in the trace log.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the state of the rxrpc call backing an afs call in each iteration of
the call wait loop in case the rxrpc call has already been terminated at
the rxrpc layer.
Interrupt the wait loop and mark the afs call as complete if the rxrpc
layer call is complete.
There were cases where rxrpc errors were not passed up to afs, which could
result in this loop waiting forever for an afs call to transition to
AFS_CALL_COMPLETE while the rx call was already complete.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change rxrpc_queue_packet()'s signature so that it can return any error
code it may encounter when trying to send the packet.
This allows the caller to eventually do something in case of error - though
it should be noted that the packet has been queued and a resend is
scheduled.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rxrpc_kernel_check_life() pass back the life counter through the
argument list and return true if the call has not yet completed.
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ICMP or ICMPV6 error is received, the error will be attached
to the socket (sk_err) and the report function will get called.
Clear any pending error here by calling sock_error().
This would cause the following attempt to use the socket to fail with
the error code stored by the ICMP error, resulting in unexpected errors
with various side effects depending on the context.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975a ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279 ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix for a potential deadlock in the TX path;
* a fix for offloaded rate-control;
* support new PCI HW IDs which use a new FW;
-----BEGIN PGP SIGNATURE-----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=EfCY
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2019-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of iwlwifi fixes intended for v5.1
* fix for a potential deadlock in the TX path;
* a fix for offloaded rate-control;
* support new PCI HW IDs which use a new FW;
Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.
This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.
Without fix retransmitted frames have wrong SN:
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1
With the fix SN stays correctly the same:
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
Cc: stable@vger.kernel.org
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
KMSAN will complain if valid address length passed to udpv6_pre_connect()
is shorter than sizeof("struct sockaddr"->sa_family) bytes.
(This patch is bogus if it is guaranteed that udpv6_pre_connect() is
always called after checking "struct sockaddr"->sa_family. In that case,
we want a comment why we don't need to check valid address length here.)
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bpf_bind() is
shorter than sizeof("struct sockaddr"->sa_family) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_llc) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_sco) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_rxrpc) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_nl) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to connect() is shorter
than sizeof("struct sockaddr"->sa_family) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof("struct sockaddr_mISDN"->family) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot is reporting uninitialized value at rds_connect() [1] and
rds_bind() [2]. This is because syzbot is passing ulen == 0 whereas
these functions expect that it is safe to access sockaddr->family field
in order to determine minimal address length for validation.
[1] https://syzkaller.appspot.com/bug?id=f4e61c010416c1e6f0fa3ffe247561b60a50ad71
[2] https://syzkaller.appspot.com/bug?id=a4bf9e41b7e055c3823fdcd83e8c58ca7270e38f
Reported-by: syzbot <syzbot+0049bebbf3042dbd2e8f@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+915c9f99f3dbc4bd6cd1@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit e21db6f69a ("tcp: track total bytes delivered with ECN CE marks")
core TCP stack does a very good job tracking ECN signals.
The "sender's best estimate of CE information" Yuchung mentioned in his
patch is indeed the best we can do.
DCTCP can use tp->delivered_ce and tp->delivered to not duplicate the logic,
and use the existing best estimate.
This solves some problems, since current DCTCP logic does not deal with losses
and/or GRO or ack aggregation very well.
This also removes a dubious use of inet_csk(sk)->icsk_ack.rcv_mss
(this should have been tp->mss_cache), and a 64 bit divide.
Finally, we can see that the DCTCP logic, calling dctcp_update_alpha() for
every ACK could be done differently, calling it only once per RTT.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Abdul Kabbani <akabbani@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of tests are verifying a route has been removed. The helper
expects the prefix as the first part of the expected output. When
checking that a route has been deleted the prefix is empty leading
to an invalid ip command:
$ ip ro ls match
Command line is not complete. Try option "help"
Fix by moving the comparison of expected output and output to a new
function that is used by both check_route and check_route6. Use the
new helper for the 2 checks on route removal.
Also, remove the reset of 'set -x' in route_setup which overrides the
user managed setting.
Fixes: d69faad765 ("selftests: fib_tests: Add prefix route tests with metric")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Norris