Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redudant calls to the PCI for changing a power state since it's done by bus
code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current kernel, the CONFIG_PPC_OF is always 'y' for the ppc
arch. So we don't need to check it with other ppc specific options.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As more ARM platforms are moving into ARCH_MULTIPLATFORM, we can now
have integrator and versatile in the same kernel, and first one selects
this driver, causing a Kconfig warning:
warning: (ARCH_INTEGRATOR_AP) selects SERIAL_AMBA_PL010 which has unmet direct dependencies (TTY && HAS_IOMEM && ARM_AMBA && (BROKEN || !ARCH_VERSATILE))
It turns out that it has not been broken on versatile for a long time,
so we can remove the statement here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This problem was taken care of three times already in
* b0de59b573 (TTY: do not update
atime/mtime on read/write),
* 37b7f3c765 (TTY: fix atime/mtime
regression), and
* b0b885657b (tty: fix up atime/mtime
mess, take three)
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com>
Cc: <stable@vger.kernel.org> # all, as b0b885657 was backported
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These quirk entries have the same effect as default
quirk entry, so we can just delete them.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b5c913f7e
("serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection")
trigger one redundant entry report message.
This patch fix it.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0aa525d118.
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d118 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO")
Reported-By: Nicolas Schichan <nschichan@freebox.fr>
Debuged-By: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6d01bb9dc8.
The exact same code was added in commit 3239fd31d4 (serial: of-serial: fetch
line number from DT) a few lined above. Doing this once should be enough.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We never report the error because we don't assign it to ret.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IRQ line connected to the DBGU UART is often shared with a timer device
which request the IRQ with IRQF_NO_SUSPEND.
Since the UART driver is correctly disabling IRQs when entering suspend
we can safely request the IRQ with IRQF_COND_SUSPEND so that irq core
will not complain about mixing IRQF_NO_SUSPEND and !IRQF_NO_SUSPEND.
Rework the interrupt handler to wake the system up when an interrupt
happens on the DEBUG_UART while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtgkACgkQMUfUDdst+ykXbACg14oFAmeYjO9RsdIHPXBvKseO
47QAn0foy91bpNQ5UFOxWS5L6Fzj2ZND
=syx2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
Merge second set of updates from Andrew Morton:
"More of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits)
mm/nommu.c: fix arithmetic overflow in __vm_enough_memory()
mm/mmap.c: fix arithmetic overflow in __vm_enough_memory()
vmstat: Reduce time interval to stat update on idle cpu
mm/page_owner.c: remove unnecessary stack_trace field
Documentation/filesystems/proc.txt: describe /proc/<pid>/map_files
mm: incorporate read-only pages into transparent huge pages
vmstat: do not use deferrable delayed work for vmstat_update
mm: more aggressive page stealing for UNMOVABLE allocations
mm: always steal split buddies in fallback allocations
mm: when stealing freepages, also take pages created by splitting buddy page
mincore: apply page table walker on do_mincore()
mm: /proc/pid/clear_refs: avoid split_huge_page()
mm: pagewalk: fix misbehavior of walk_page_range for vma(VM_PFNMAP)
mempolicy: apply page table walker on queue_pages_range()
arch/powerpc/mm/subpage-prot.c: use walk->vma and walk_page_vma()
memcg: cleanup preparation for page table walk
numa_maps: remove numa_maps->vma
numa_maps: fix typo in gather_hugetbl_stats
pagemap: use walk->vma instead of calling find_vma()
clear_refs: remove clear_refs_private->vma and introduce clear_refs_test_walk()
...
Pull s390 updates from Martin Schwidefsky:
- The remaining patches for the z13 machine support: kernel build
option for z13, the cache synonym avoidance, SMT support,
compare-and-delay for spinloops and the CES5S crypto adapater.
- The ftrace support for function tracing with the gcc hotpatch option.
This touches common code Makefiles, Steven is ok with the changes.
- The hypfs file system gets an extension to access diagnose 0x0c data
in user space for performance analysis for Linux running under z/VM.
- The iucv hvc console gets wildcard spport for the user id filtering.
- The cacheinfo code is converted to use the generic infrastructure.
- Cleanup and bug fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/process: free vx save area when releasing tasks
s390/hypfs: Eliminate hypfs interval
s390/hypfs: Add diagnose 0c support
s390/cacheinfo: don't use smp_processor_id() in preemptible context
s390/zcrypt: fixed domain scanning problem (again)
s390/smp: increase maximum value of NR_CPUS to 512
s390/jump label: use different nop instruction
s390/jump label: add sanity checks
s390/mm: correct missing space when reporting user process faults
s390/dasd: cleanup profiling
s390/dasd: add locking for global_profile access
s390/ftrace: hotpatch support for function tracing
ftrace: let notrace function attribute disable hotpatching if necessary
ftrace: allow architectures to specify ftrace compile options
s390: reintroduce diag 44 calls for cpu_relax()
s390/zcrypt: Add support for new crypto express (CEX5S) adapter.
s390/zcrypt: Number of supported ap domains is not retrievable.
s390/spinlock: add compare-and-delay to lock wait loops
s390/tape: remove redundant if statement
s390/hvc_iucv: add simple wildcard matches to the iucv allow filter
...
Commit 5695be142e ("OOM, PM: OOM killed task shouldn't escape PM
suspend") has left a race window when OOM killer manages to
note_oom_kill after freeze_processes checks the counter. The race
window is quite small and really unlikely and partial solution deemed
sufficient at the time of submission.
Tejun wasn't happy about this partial solution though and insisted on a
full solution. That requires the full OOM and freezer's task freezing
exclusion, though. This is done by this patch which introduces oom_sem
RW lock and turns oom_killer_disable() into a full OOM barrier.
oom_killer_disabled check is moved from the allocation path to the OOM
level and we take oom_sem for reading for both the check and the whole
OOM invocation.
oom_killer_disable() takes oom_sem for writing so it waits for all
currently running OOM killer invocations. Then it disable all the further
OOMs by setting oom_killer_disabled and checks for any oom victims.
Victims are counted via mark_tsk_oom_victim resp. unmark_oom_victim. The
last victim wakes up all waiters enqueued by oom_killer_disable().
Therefore this function acts as the full OOM barrier.
The page fault path is covered now as well although it was assumed to be
safe before. As per Tejun, "We used to have freezing points deep in file
system code which may be reacheable from page fault." so it would be
better and more robust to not rely on freezing points here. Same applies
to the memcg OOM killer.
out_of_memory tells the caller whether the OOM was allowed to trigger and
the callers are supposed to handle the situation. The page allocation
path simply fails the allocation same as before. The page fault path will
retry the fault (more on that later) and Sysrq OOM trigger will simply
complain to the log.
Normally there wouldn't be any unfrozen user tasks after
try_to_freeze_tasks so the function will not block. But if there was an
OOM killer racing with try_to_freeze_tasks and the OOM victim didn't
finish yet then we have to wait for it. This should complete in a finite
time, though, because
- the victim cannot loop in the page fault handler (it would die
on the way out from the exception)
- it cannot loop in the page allocator because all the further
allocation would fail and __GFP_NOFAIL allocations are not
acceptable at this stage
- it shouldn't be blocked on any locks held by frozen tasks
(try_to_freeze expects lockless context) and kernel threads and
work queues are not frozen yet
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Suggested-by: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While touching this area let's convert printk to pr_*. This also makes
the printing of continuation lines done properly.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UARTs which do not trigger THRE interrupt if the fifo is already
empty when the interrupt is enabled need tx primed manually. These
UARTs are identified by the UART_BUG_TXEN flag to enable the
required workaround.
However, the current workaround is broken; if the fifo is already
empty but the shifter is still transmitting, then serial8250_tx_chars()
will not be called but no further THRE interrupt will occur, and
tx will stall. The appropriate check is for fifo empty (THRE), not
transmitter empty (TEMT).
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
[pjh: rewrote commit log]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the last missing piece to get a kernel booting to a prompt in qemu-cris.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sprop is unused in find_console_handle() since commit a752ee56ad
("tty: Update hypervisor tty drivers to use core stdout parsing code.")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The general agreed way to specify a fixed line number
for a serial console is to provide a "serial" alias
in the devicetree. Start parsing this property in
of_serial.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EarlyCon support depends on serial console infrastructure, so the code
implementing it should depend on CONFIG_SERIAL_SAMSUNG_CONSOLE.
This patch fixes the following build break:
CC [M] drivers/tty/serial/samsung.o
drivers/tty/serial/samsung.c:2468:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2468:1: error: expected declaration specifiers or ‘...’ before ‘s3c2410_setup_earlycon’
drivers/tty/serial/samsung.c:2487:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2487:1: error: expected declaration specifiers or ‘...’ before ‘s3c2412_setup_earlycon’
drivers/tty/serial/samsung.c:2488:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2488:1: error: expected declaration specifiers or ‘...’ before ‘s3c2440_setup_earlycon’
drivers/tty/serial/samsung.c:2489:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2489:1: error: expected declaration specifiers or ‘...’ before ‘s3c6400_setup_earlycon’
drivers/tty/serial/samsung.c:2506:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2506:1: error: expected declaration specifiers or ‘...’ before ‘s5pv210_setup_earlycon’
drivers/tty/serial/samsung.c:2507:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2507:1: error: expected declaration specifiers or ‘...’ before ‘exynos4210_setup_earlycon’
drivers/tty/serial/samsung.c:2468:1: warning: ‘s3c2410_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2487:1: warning: ‘s3c2412_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2488:1: warning: ‘s3c2440_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2489:1: warning: ‘s3c6400_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2506:1: warning: ‘s5pv210_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2507:1: warning: ‘exynos4210_setup_earlycon’ defined but not used [-Wunused-function]
make[3]: *** [drivers/tty/serial/samsung.o] Error 1
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/8250/8250_core.c:2503:6: sparse: symbol 'serial8250_set_divisor' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a full sc9836-uart driver for SC9836 SoC which is based on the
spreadtrum sharkl64 platform.
This driver also support earlycon.
Originally-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function s3c24xx_serial_start_tx_pio() enables interrupts if needed,
so we don't have to (or even we shouldn't) enable them before.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_set_termios() is an internal helper intended for file scope use.
UART drivers which are capable of driving the RTS pin must
properly handle the tiocmset() method, regardless of termios settings.
A failure to do so is a UART driver bug and should be fixed there.
Do not use this interface to workaround UART driver bugs.
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: <linux-bluetooth@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART ignores MCR[1] (ie., RTS) when in autoRTS mode. This
makes it impossible for either the serial core or userspace to
manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88838d3112702 ("serial: omap_8250: Fix RTS handling") fixed
RTS pin control when in autoRTS mode.
New support added in "serial: core: Rework hw-assisted flow control support"
enables a much simpler approach; rather than masking out autoRTS
whenever writing the EFR register, use the UPSTAT_* mode to determine if
autoRTS should be enabled when raising RTS (in omap8250_set_mctrl()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cb ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7a ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA variant of the 8250 UART adds a UART enable bit which must not
be cleared. Make the earlycon support maintain this bit if it is set.
This implies some initialization of the UART, but we cannot
unconditionally set the bit as some other variants require this bit to
be clear for other functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mrvl,pxa-uart and mrvl,mmp-uart compatible strings for the of_serial
driver. These are 8250 variants which have a port type of PORT_XSCALE.
There is also the serial driver pxa.c with these compatible strings
already. However, it can be replaced with the common 8250 driver. It has
some issues like it cannot coexist with the 8250 driver due to tty name
collision. That also means adding these compatible strings here should
not case a problem.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for alias parsing from the DT. This allows for consistent
tty numbering.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port shadow registers, ->fcr and ->mcr, must be protected from
concurrent updates. Relocate the shadow register updates in
serial8250_do_set_termios() to the port lock critical section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.
Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.
This workaround is disabled for omap_8250 (which uses different divisor
programming).
Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar XR17V35X PCIe uarts support a 4-bit fractional divisor register.
Refactor the divisor calculation from the divisor programming.
Allow a fractional result from serial8250_get_divisor() and pass this
result to serial8250_dl_write().
Simplify the calculation for quot and quot_frac. This was verified
to be identical to the results of the original calculation with a test
jig.
NB: The results were also compared with the divisor value chart
on pg 33 of the Exar XR17V352 datasheet, rev 1.0.3, here:
http://www.exar.com/common/content/document.ashx?id=1585
which differs from the calculated values by 1 in the fractional result.
This is because the calculated values are still rounded in the
fractional result, whereas the table values are truncated. Note
that the data error rate % values in the datasheet are for
rounded fractional results, as the truncated fractional results
have more error.
Cc: Joe Schultz <jschultz@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor divisor register programming into a new function,
serial8250_set_divisor; this allows serial console to reinitialize
early after resume from suspend.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the computation of the LCR register value from termios c_cflag
into a new local function, serial8250_compute_lcr().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_BUG_QUOT workaround adjusts the divisor computed from the
baud rate by serial8250_get_divisor(). Move the workaround into
serial8250_get_divisor(), so that divisor-from-baud computation
is encapsulated.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
16z135 IP Core has changed so the driver needs to be updated to respect
these changes. The following changes have been made:
* Don't invert the 16z135 modem status register when reading.
* Add module parameter to configure the (baud rate dependent) RX timeout.
Character timeout in seconds = (timeout_reg * baud_reg * 4)/freq_reg.
* Enable the handling of UART core's automatic flow control feature.
When AFE is active disable generation of modem status IRQs.
* Rework the handling of IRQs to be conform with newer FPGA versions and
take precautions not to miss an interrupt because of the destructive read
of the IIR register.
* Correct men_z135_handle_modem_status(), MSR is stat_reg[15:8] not
stat_reg[7:0]
* Correct calling of uart_handle_{dcd,cts}_change()
* Reset CLOCAL when CRTSCTS is set
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart port being suspended is a console and consoles are
not suspending (kernel command line contains no_console_suspend),
then no action is performed for that port, and the function can
return early.
If the function has not returned early, then one of the conditions
is not true, so the expression
(console_suspend_enabled || !uart_console(uport))
must be true and can be eliminated.
Similarly, the expression
(console_suspend_enabled && uart_console(uport))
simplifies to just uart_console(uport).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BRKINT and ISIG requires input and output flush when a signal char
is received. However, the order of operations is significant since
parallel i/o may be ongoing.
Merge the signal handling for BRKINT with ISIG handling.
Process the signal first. This ensures any ongoing i/o is aborted;
without this, a waiting writer may continue writing after the flush
occurs and after the signal char has been echoed.
Write lock the termios_rwsem, which excludes parallel writers from
pushing new i/o until after the output buffers are flushed; claiming
the write lock is necessary anyway to exclude parallel readers while
the read buffer is flushed.
Subclass the termios_rwsem for ptys since the slave pty performing
the flush may appear to reorder the termios_rwsem->tty buffer lock
lock order; adding annotation clarifies that
slave tty_buffer lock-> slave termios_rwsem -> master tty_buffer lock
is a valid lock order.
Flush the echo buffer. In this context, the echo buffer is 'output'.
Otherwise, the output will appear discontinuous because the output buffer
was cleared which contains older output than the echo buffer.
Open-code the read buffer flush since the input worker does not need
kicking (this is the input worker).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pty driver does not clear its write buffer when commanded.
This is to avoid an apparent deadlock between parallel flushes from
both pty ends; specifically when handling either BRK or INTR input.
However, parallel flushes from this source is not possible since
the pty master can never be set to BRKINT or ISIG. Parallel flushes
from other sources are possible but these do not threaten deadlocks.
Annotate the tty buffer mutex for lockdep to represent the nested
tty_buffer locking which occurs when the pty slave is processing input
(its buffer mutex held) and receives INTR or BRK and acquires the
linked tty buffer mutex via tty_buffer_flush().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides nested legacy_mutex locking which is required on pty pair
teardown, other nested pty operations require lock subclassing.
Move lock subclass definition to tty interface header, include/linux/tty.h,
and document its use.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In canon mode, the read buffer head will advance over the buffer tail
if the input > 4095 bytes without receiving a line termination char.
Discard additional input until a line termination is received.
Before evaluating for overflow, the 'room' value is normalized for
I_PARMRK and 1 byte is reserved for line termination (even in !icanon
mode, in case the mode is switched). The following table shows the
transform:
actual buffer | 'room' value before overflow calc
space avail | !I_PARMRK | I_PARMRK
--------------------------------------------------
0 | -1 | -1
1 | 0 | 0
2 | 1 | 0
3 | 2 | 0
4+ | 3 | 1
When !icanon or when icanon and the read buffer contains newlines,
normalized 'room' values of -1 and 0 are clamped to 0, and
'overflow' is 0, so read_head is not adjusted and the input i/o loop
exits (setting no_room if called from flush_to_ldisc()). No input
is discarded since the reader does have input available to read
which ensures forward progress.
When icanon and the read buffer does not contain newlines and the
normalized 'room' value is 0, then overflow and room are reset to 1,
so that the i/o loop will process the next input char normally
(except for parity errors which are ignored). Thus, erasures, signalling
chars, 7-bit mode, etc. will continue to be handled properly.
If the input char processed was not a line termination char, then
the canon_head index will not have advanced, so the normalized 'room'
value will now be -1 and 'overflow' will be set, which indicates the
read_head can safely be reset, effectively erasing the last char
processed.
If the input char processed was a line termination, then the
canon_head index will have advanced, so 'overflow' is cleared to 0,
the read_head is not reset, and 'room' is cleared to 0, which exits
the i/o loop (because the reader now have input available to read
which ensures forward progress).
Note that it is possible for a line termination to be received, and
for the reader to copy the line to the user buffer before the
input i/o loop is ready to process the next input char. This is
why the i/o loop recomputes the room/overflow state with every
input char while handling overflow.
Finally, if the input data was processed without receiving
a line termination (so that overflow is still set), the pty
driver must receive a write wakeup. A pty writer may be waiting
to write more data in n_tty_write() but without unthrottling
here that wakeup will not arrive, and forward progress will halt.
(Normally, the pty writer is woken when the reader reads data out
of the buffer and more space become available).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If PARMRK is enabled, the available read buffer space computation is
overly-pessimistic, which results in severely throttled i/o, even
in the absence of parity errors. For example, if the 4k read buffer
contains 1k processed data, the input worker will compute available
space of 333 bytes, despite 3k being available. At 1365 chars of
processed data, 0 space available is computed.
*Divide remaining space* by 3, truncating down (if left == 2, left = 0).
Reported-by: Christian Riesch <christian.riesch@omicron.at>
Conflicts:
drivers/tty/n_tty.c
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add commit_head buffer index, which the producer-side publishes
after input processing in non-canon mode. This ensures the consumer-side
observes correctly-ordered writes in non-canonical mode (ie., the buffer
data is written before the buffer index is advanced). Fix consumer-side
uses of read_cnt() to use commit_head instead.
Add required memory barriers to the tail index to guarantee
the consumer-side has completed the loads before the producer-side
begins writing new data. Open-code the producer-side receive_room()
into the i/o loop.
Remove no-longer-referenced receive_room().
Based on work by Christian Riesch <christian.riesch@omicron.at>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The adjustments performed by receive_room() are to ensure a line
termination can always be written to the read buffer. However,
these adjustments are irrelevant to the throttle threshold (because
the threshold < buffer limit).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty driver will be mistakenly throttled if a line termination
has not been received, and the line exceeds 3967 chars. Thus, it is
possible for the driver to stop sending when it has not yet sent
the newline. This does not apply to the pty driver.
Don't throttle until at least one line termination has been
received.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The input worker never reschedules itself; it only processes input until
either there is no more input or the read buffer is full. So the reader
is responsible for restarting the input worker only if the read buffer
was previously full (no_room == 1) _and_ space is now available to process
more input because the reader has consumed data from the read buffer.
However, computing the actual space available is not required to determine
if the reader has consumed data from the read buffer. This condition is
evaluated in 5 situations, each of which the space avail is already known:
1. n_tty_flush_buffer() - the read buffer is empty; kick the worker
2. n_tty_set_termios() - no data has been consumed; do not kick the worker
(although it may have kicked the reader so data _will be_ consumed)
3. n_tty_check_unthrottle - avail space > 3968; kick the worker
4. n_tty_read, before leaving - only kick the worker if the reader has
moved the tail. This prevents unnecessarily kicking the worker
when timeout-style reading is used.
5. n_tty_read, before sleeping - although it is possible for the read
buffer to be full and input_available_p() to be false, this can
only happen when the input worker is racing the reader, in which
case the reader will have been woken and won't sleep.
Rename n_tty_set_room() to n_tty_kick_worker() to reflect what the
function actually does.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for early console initialized from device tree
and kernel command line to all variants of Samsung serial driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[mszyprow: added support for command line based initialization,
fixed comments, added documentation]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver cannot return from overrun error if characters
are output during overrun process, use dev_dbg() instead of
dev_notice() to log the error message of overrun in syslog.
Based on a patch by Hisashi Nakamura.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we would like to send amount of data less than FIFO size we better would do
this via PIO mode. Otherwise the overhead could be significant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sci_{suspend|remove}() for the PM {freeze|
thaw|restore}() methods. It's handy to achieve this by using SIMPLE_DEV_PM_OPS()
macro, however we have to annotate sci_{suspend|remove}() with '__maybe_unused'
in order to avoid compilation warnings when CONFIG_PM_SLEEP is undefined.
Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pty_space() computation is broken; the space already consumed
in the tty buffer is not accounted for.
Use tty_buffer_set_limit(), which enforces the limit automatically.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of flushing the RX FIFO breaks in a number of cases,
it is impossible to ensure an complete flush of the RX FIFO due to the
hardware not allowing the use of the FIFOs when the receiver is disabled
(Reading from the FIFO register does not remove it from the FIFO when
the RX_EN=0 or RX_DIS=1). Additionally during an initial set_termios
call where RX_DIS=1 causes a hang waiting forever for the RX FIFO to
empty. On top of this the FIFO will be cleared by the use of the RXRST
bits on the Control Register, making the RX flush pointless (as it does
not preserve the data read anyway).
Due to the TXRST the TX FIFO and transmitter can be interrupted during
frame trasmission, causing corruption and additionally data lost in the
FIFO. Most other serial drivers do not flush or clear the FIFOs during
a termios configuration change and as such do not have issues with
corruption. For this UART controller is it required that the TXRST/RXRST
bit be flagged during the change, this means that the data in the FIFO
will be dropped when changing configuration. In order to prevent data
loss and corruption of the transmitted data, wait until the TX FIFO is
empty before changing the configuration. The performance of this may
cause the set_termios call to take a longer amount of time especially
on lower baud rates, however it is comparable to the same performance
hit that a console_write call costs.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Acked-by: Anirudha Sarangi <anirudh@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building an arm allmodconfig kernel triggers a lengthy but harmless
warning in the isicom driver:
drvers/tty/isicom.c: In function 'isicom_send_break':
uapi/linux/swab.h:13:15: warning: integer overflow in expression [-Woverflow]
(((__u16)(x) & (__u16)0x00ffU) << 8) | \
^
uapi/linux/swab.h:107:2: note: in expansion of macro '___constant_swab16'
___constant_swab16(x) : \
^
uapi/linux/byteorder/big_endian.h:34:43: note: in expansion of macro '__swab16'
#define __cpu_to_le16(x) ((__force __le16)__swab16((x)))
^
linux/byteorder/generic.h:89:21: note: in expansion of macro '__cpu_to_le16'
#define cpu_to_le16 __cpu_to_le16
^
include/asm/io.h:270:6: note: in expansion of macro 'cpu_to_le16'
cpu_to_le16(v),__io(p)); })
^
drivers/tty/isicom.c:1058:2: note: in expansion of macro 'outw'
outw((length & 0xff00), base);
^
Apparently, the problem is related to the fact that the value 0xff00,
when used as a 16-bit number, is negative and passed into bitwise
operands of the generic byte swapping code.
Marking the input argument as unsigned in both technically correct
and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to explicitly zero the 'ret' variable as it is properly
initialized in a few lines below as:
ret = serial_mxs_probe_dt(s, pdev);
Remove the unneeded zeroing of 'ret'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should check whether platform_get_irq() failed, and in the case of error
this needs to be propagated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irq number is only used inside the probe function, so there is no need
to keep it in the private mxs_auart_port structure.
Use a local 'irq' variable for storing the irq number instead.
Also make its type of 'int' as platform_get_irq() may fail and return a
negative number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Digicolor USART hardware does not support detecting the BREAK condition.
This means that we can't support sysrq on this hardware. Remove all reference
to sysrq from the code.
This also fixes build when sysrq is disabled:
drivers/tty/serial/digicolor-usart.c: In function 'digicolor_uart_console_write':
drivers/tty/serial/digicolor-usart.c:407:33: error: 'struct uart_port' has no member named 'sysrq'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.
When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change does following:
- baud, flow, bits, parity were being overwritten as they were
being reinitialized after parsing. Initialize them when they are
declared so that user provided setting are not overwritten.
- msm_set_baud_rate() is anyway called in uart_set_options when it calls
msm_set_termios(). msm_reset() is called when we change the baud rate.
Hence doing away with both of these calls.
- CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
So do away with this here.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.
This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.
Clear UCR2_SRST bit so that the UART FIFO is flushed properly.
Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Acked-by: Jason Liu <r64343@freecale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.
This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.
Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.
Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 26df6d1340 ("tty: Add EXTPROC support for LINEMODE")
allows a process which has opened a pty master to send _any_ signal
to the process group of the pty slave. Although potentially
exploitable by a malicious program running a setuid program on
a pty slave, it's unknown if this exploit currently exists.
Limit to signals actually used.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Howard Chu <hyc@symas.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org> # 2.6.36+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vcs device's poll/fasync support relies on the vt notifier to signal
changes to the screen content. Notifier invocations were missing for
changes that comes through the selection interface though. Fix that.
Tested with BRLTTY 5.2.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: Dave Mielke <dave@mielke.cc>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a wildcard character to filter a range of z/VM user IDs with a single
filter entry. Only the leading portion up to the wildcard of an filter entry
contributes to the match.
This reduces the filter size and avoids configuration updates when deploying
new terminal server instances.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently vt_bind and vt_unbind access at least the con_driver object
and registered_con_driver array without holding the console lock. Fix
this by locking around the whole function in each case.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default console driver (conswitchp) and busy drivers bound to a
console (as reported by con_is_bound()) shouldn't be unregistered.
System console drivers (without the CON_DRIVER_FLAG_MODULE flag) can be
unregistered, provided they are neither default nor busy. The current
code checks for the CON_DRIVER_FLAG_INIT flag but this doesn't make
sense: this flag is set for a driver whenever its associated console's
con_startup() function is called, which first happens when the console
driver is registered (so before the console gets bound) and gets cleared
when the console gets unbound. The purpose of this flag is to show if we
need to call con_startup() on a console before we use it.
Based on the above, do_unregister_con_driver() in its current form will
allow unregistering a console driver only if it was never bound, but
will refuse to unregister one that was bound and later unbound.
Fix this by dropping the CON_DRIVER_FLAG_INIT check, allowing
unregistering of any console driver provided that it's not the default
one and it's not busy.
v2:
- reword the third paragraph to clarify how the fix works (Peter Hurley)
v3:
- unchanged
v4:
- Allow unregistering a system console driver too, needed by i915 to
unregister vgacon. Update commit description accordingly. (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the last argument of serial_paranoia_check by the actual function
name.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In early 8250, IER is already zero so no point in writing this - twice
per line
This helped improve the SystemC model based ARC OSCI platform
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
workaround of errata A-008006 which states that tx_loadsz should
be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IGNPAR is set in termios->c_iflag, characters with
framing errors should be ignored.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNPAR/INPCK are clear in termios->c_iflag, characters
received with parity or framing errors should be preserved
and passed to the upper layers of the tty stack.
Specifically, the decision of whether to set the character
value to zero should be made by n_tty.c/n_tty_receive_parity_error().
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RX DMA transfers support for samsung serial driver. It's enabled
when DMA controller for RX channel is specified in device-tree.
DMA transactions are started when number of bytes in RX FIFO reaches
trigger level, otherwise PIO mode is used. DMA transfer size is always
PAGE_SIZE which can cause large latency when smaller data amount is
transferred, so we always terminate DMA transaction on RX timeout
interrupt. Timeout interval is set to 64 frame times.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add TX DMA transfers support for samsung serial driver. It's enabled
when "dmas" property is defined in serial device-tree node, otherwise
TX transfers are prerformed using PIO.
TX DMA is used for data segments larger than fifosize to reduce number
of interrupts during data transmission. For buffers shorter than fifosize
PIO mode is selected.
Data blocks for DMA transfers are aligned to cache line size to avoid
problems with coherency (some areas of TX circ buffer can be used by
CPU during DMA transaction, so we have to ensure that our data is always
consistent).
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functions requesting and releasing RX and TX DMA channels. This
function are called only when "dmas" property in serial device-tree
node is defined.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have "dmas" property in serial node in device-tree, we do
memory alocation for dma structure which will be used in DMA handling
code.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This struct contains DMA configuration for each serial port.
It will be used in next commits adding DMA support in driver.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds Software flow control support in DMA mode.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other than enable Receiver Overrun Interrupt Enable (UCR4_OREN)
in start_tx interface, UCR4_OREN should be enabled before enable
of Receiver.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start rx_dma once RXFIFO is not empty that can avoid dma request lost
and causes data delay issue.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA mode for UART can be used even w/o HW flow control with RTS/CTS.
So it need to be initialized and enabled earlier.
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminating the DMA, make sure the interrupt is disabled, too.
This fixes random kernel Oops due to dma_tx_call() called for
invalid transmissions.
If we disable the TDMAEN, make sure it's enabled again if a TX
DMA is started.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in dma_tx_callback(), no matter if there is still
remaining data pending in circle buffer or not, DMA transmit
will be terminated.
This will result in some data never get transmitted.
In order to fix this issue, call imx_dma_tx() again in
dma_tx_callback, when there is pending data and uart hasn't
been stopped.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad28e3efe.
Instead of always wake up write_wait process in TX callback,
TX callback should call imx_dma_tx() again, and let imx_dma_tx
transfer the remaining data in circle buffer.
The issue with commit 2ad28e3 is, in case there is remaining
data in circle buffer, but no process is waiting on write_wait
queue, then as no following uart_write() will be called after
uart_write_wakeup(), thus cause data loss.
Moreover according to Documentation/serial/driver, uart_write_wakeup()
should be called in case the transmit buffer have dropped below
a threshold.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To synchronize between dma_tx_callback() and imx_dma_tx() use the same
variable, dma_is_txing. This prevents any race between these two functions
and ensures that a new DMA can start only after the first has been
finished.
Before the new DMA can be set up, update the circular buffer logic, first.
Therefore, change dma_is_txing after that update, instead of before.
While doing this, in dma_tx_callback() extend the locking to dma_unmap_sg()
and the update of dma_is_txing.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, reformat the code to exit immediately. This allows us to add
more code in more readable format.
In case the TX DMA was still running, remove and disable it's resources.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case dmaengine_prep_slave_sg() fails, add the missing dma_unmap_sg().
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inverting the logic of the if statement for the sg initialization
makes the if statement easier and better to read.
No functional change.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use imx_start_tx() just to enable the TX interrupt. It's the job of the
TX interrupt ISR to fill the transmit buffer, then. If the transmit buffer
is empty, the TX interrupt should be executed as soon as the start_tx()
enables the interrupt, so there is no reason for the extra
imx_transmit_buffer() call, here. Remove it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several places are accessing the UCR1 register without locking.
This probably will cause a race issue when another thread
is accessing the same register.
Add locking to preventing concurrent access of the UCR1 register.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CREAD flag hanlding in set_termios and UART DMA mode
which ignores all received chars when CREAD flag cleared.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes many bugs in the code dealing with the hardware handshake.
As an example, in atmel_set_termios(), we used to test whether the CRTSCTS
c_cflag was set. If so, we selected the "Hardware Handshake" mode through the
Mode Register. However, few lines below the mode was reset to "Normal" (0).
So there was no way to select the "Hardware Handshake" mode. To fix this issue,
we moved the CRTSCRTS c_cflag test AFTER the mode has been reset to "Normal".
Also setting the RTSEN and RTSDIS bits in the Control Register has different
results whether the USART is set in "Normal" or "Hardware Handshake" mode:
1) "Normal" mode
- the RTSEN bit forces the RTS line to low level, which tells the remote peer
that we are ready to received new data.
- the RTSDIS bit forces the RTS line to high level, which tells the remote peer
to stop sending new data.
2) "Hardware Handshake" mode
- the RTSEN bit forces the RTS line to high level.
- the RTSDIS bit lets the hardware control the RTS line.
WARNING:
when FIFOs are not available or not enabled, the RTS line is controlled by the
PDC. This is why using the Hardware Handshake mode requires using the PDC
channel for reception. However the Hardware Handshake mode DOES NOT work with
DMA controller since it cannot control the RTS line.
Future designs with FIFOs will introduce a new feature: the RTS line will be
controlled by the RX FIFO using thresholds. This patch was tested with this new
design.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-EDEFER error wasn't handle properly by atmel_serial_probe().
As an example, when atmel_serial_probe() is called for the first time, we pass
the test_and_set_bit() test to check whether the port has already been
initalized. Then we call atmel_init_port(), which may return -EDEFER, possibly
returned before by clk_get(). Consequently atmel_serial_probe() used to return
this error code WITHOUT clearing the port bit in the "atmel_ports_in_use" mask.
When atmel_serial_probe() was called for the second time, it used to fail on
the test_and_set_bit() function then returning -EBUSY.
When atmel_serial_probe() fails, this patch make it clear the port bit in the
"atmel_ports_in_use" mask, if needed, before returning the error code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_serial_probe() calls atmel_init_port(). In turn, atmel_init_port() calls
clk_disable_unprepare() to disable the peripheral clock before returning.
Later atmel_serial_probe() accesses some I/O registers such as the Mode and
Control registers for RS485 support then the Name and Version registers, through a call to
atmel_get_ip_name(), but at that moment the peripheral clock was still
disabled.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MARCO will not be supported any more and the project was dropped.
it has been replaced by CSR atlas7.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2aff5e2bc6 ('tty: Change
tty lock order to master->slave') added a warning which is broken
and unnecessary now that the tty lock has fixed lock subclasses,
added in commit 2febdb632b
('tty: Preset lock subclass for nested tty locks').
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable APM X-Gene SoC serial port functionality when using ACPI table to
initialize serial port.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to terminate transfer in the __dma_rx_complete() since it's
called at the end of transfer. Special case when serial timeout occurs is
handled separately where we have to terminate transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_request_irq() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_clk_get() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_kzalloc() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of jumping to the 'out' label, let's return the error immediately, which
makes the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the OMAP3 UART ignores MCR[1] (RTS) in autoRTS mode, autoRTS
mode must not be enabled unless RTS is set (or port->mctrl & TIOCM_RTS,
which is equivalent).
Fixes premature raising of RTS in omap_8250_set_termios() -- RTS was
raised even before UART mode was selected.
Fixes raise of RTS after port has been shutdown; omap_8250_pm() re-enabled
RTS after omap_8250_shutdown().
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fixes for omap-serial.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
index 18c30ca..f43ed2c 100644
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch invokes add_preferred_console() with ttyS based on ttyO
arguments if the user didn't specify it on its own. This ensures that
the user will see the kernel booting on his serial console in case he
forgot to update the command line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current output of the device probing looks like this:
ColdFire internal UART serial driver
(NULL device *): ttyS0 at MMIO 0xfc060000 (irq = 90, base_baud = 5208333) is a ColdFire UART
console [ttyS0] enabled
(NULL device *): ttyS1 at MMIO 0xfc064000 (irq = 91, base_baud = 5208333) is a ColdFire UART
(NULL device *): ttyS2 at MMIO 0xfc068000 (irq = 92, base_baud = 5208333) is a ColdFire UART
Fix the port device linkage at probing time so that the device name is
printed out properly, and not "(NULL device *)".
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivially fix the following compile time warnings:
CC drivers/tty/serial/mcf.o
drivers/tty/serial/mcf.c: In function ‘mcf_set_termios’:
drivers/tty/serial/mcf.c:201:19: warning: unused variable ‘pp’
drivers/tty/serial/mcf.c: In function ‘mcf_config_rs485’:
drivers/tty/serial/mcf.c:444:19: warning: unused variable ‘pp’
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change my email contact address from the obsolete gerg@snapgear.com to
gerg@uclinux.org.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c4dc304677.
This fix is superseded by commit 52bce7f8d4,
'pty, n_tty: Simplify input processing on final close'.
The final close now waits for input processing to complete before
destroying the pty, so poll() does not need to special case this
condition.
Cc: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exclusive mode ttys (TTY_EXCLUSIVE) do not allow further reopens;
fail the condition before associating the file pointer and calling
the driver open() method.
Prevents DTR programming when the tty is already in exclusive mode.
Reported-by: Shreyas Bethur <shreyas.bethur@ni.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Shreyas Bethur <shreyas.bethur@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WCH384 4S board is a PCI-E card with 4 DB9 COM ports detected as
Serial controller: Device 1c00:3470 (rev 10) (prog-if 05 [16850])
Signed-off-by: Sergej Pupykin <ml@sergej.pp.ru>
Acked-by: Zany Yan <sirlight@cox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This is a partial revert of 2f2dafe (serial: serial_core.c: printk
replacement) which gets us booting again. The real problem seems to be
the _emit path in early boot. However, until we can root cause it, we
need at least to get boot working.
Fixes: 2f2dafe77d
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_omap serial driver is a new user of CONFIG_PM_RUNTIME.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
#ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in 8250_omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Here's the big tty/serial driver update for 3.19-rc1.
There are a number of TTY core changes/fixes in here from Peter Hurley
that have all been teted in linux-next for a long time now. There are
also the normal serial driver updates as well, full details in the
changelog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD/MACgkQMUfUDdst+ymW+wCfbSzoYMRObIImMPWfoQtxkvvN
rpkAnAtyEP/zZIfkQIuKTSH6FJxocF8V
=WZt3
-----END PGP SIGNATURE-----
Merge tag 'tty-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.19-rc1.
There are a number of TTY core changes/fixes in here from Peter Hurley
that have all been teted in linux-next for a long time now. There are
also the normal serial driver updates as well, full details in the
changelog below"
* tag 'tty-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (219 commits)
serial: pxa: hold port.lock when reporting modem line changes
tty-hvsi_lib: Deletion of an unnecessary check before the function call "tty_kref_put"
tty: Deletion of unnecessary checks before two function calls
n_tty: Fix read_buf race condition, increment read_head after pushing data
serial: of-serial: add PM suspend/resume support
Revert "serial: of-serial: add PM suspend/resume support"
Revert "serial: of-serial: fix up PM ops on no_console_suspend and port type"
serial: 8250: don't attempt a trylock if in sysrq
serial: core: Add big-endian iotype
serial: samsung: use port->fifosize instead of hardcoded values
serial: samsung: prefer to use fifosize from driver data
serial: samsung: fix style problems
serial: samsung: wait for transfer completion before clock disable
serial: icom: fix error return code
serial: tegra: clean up tty-flag assignments
serial: Fix io address assign flow with Fintek PCI-to-UART Product
serial: mxs-auart: fix tx_empty against shift register
serial: mxs-auart: fix gpio change detection on interrupt
serial: mxs-auart: Fix mxs_auart_set_ldisc()
serial: 8250_dw: Use 64-bit access for OCTEON.
...
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- 'Nested Sleep Debugging', activated when CONFIG_DEBUG_ATOMIC_SLEEP=y.
This instruments might_sleep() checks to catch places that nest
blocking primitives - such as mutex usage in a wait loop. Such
bugs can result in hard to debug races/hangs.
Another category of invalid nesting that this facility will detect
is the calling of blocking functions from within schedule() ->
sched_submit_work() -> blk_schedule_flush_plug().
There's some potential for false positives (if secondary blocking
primitives themselves are not ready yet for this facility), but the
kernel will warn once about such bugs per bootup, so the warning
isn't much of a nuisance.
This feature comes with a number of fixes, for problems uncovered
with it, so no messages are expected normally.
- Another round of sched/numa optimizations and refinements, for
CONFIG_NUMA_BALANCING=y.
- Another round of sched/dl fixes and refinements.
Plus various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched: Add missing rcu protection to wake_up_all_idle_cpus
sched/deadline: Introduce start_hrtick_dl() for !CONFIG_SCHED_HRTICK
sched/numa: Init numa balancing fields of init_task
sched/deadline: Remove unnecessary definitions in cpudeadline.h
sched/cpupri: Remove unnecessary definitions in cpupri.h
sched/deadline: Fix rq->dl.pushable_tasks bug in push_dl_task()
sched/fair: Fix stale overloaded status in the busiest group finding logic
sched: Move p->nr_cpus_allowed check to select_task_rq()
sched/completion: Document when to use wait_for_completion_io_*()
sched: Update comments about CLONE_NEWUTS and CLONE_NEWIPC
sched/fair: Kill task_struct::numa_entry and numa_group::task_list
sched: Refactor task_struct to use numa_faults instead of numa_* pointers
sched/deadline: Don't check CONFIG_SMP in switched_from_dl()
sched/deadline: Reschedule from switched_from_dl() after a successful pull
sched/deadline: Push task away if the deadline is equal to curr during wakeup
sched/deadline: Add deadline rq status print
sched/deadline: Fix artificial overrun introduced by yield_task_dl()
sched/rt: Clean up check_preempt_equal_prio()
sched/core: Use dl_bw_of() under rcu_read_lock_sched()
sched: Check if we got a shallowest_idle_cpu before searching for least_loaded_cpu
...
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new
iommu DT binding. More drivers like this are likely to follow
for the following merge window, but we should be able to do
those through the iommu maintainer.
Other notable changes are:
* reset controller drivers from the reset maintainer (socfpga, sti, berlin)
* fixes for the keystone navigator driver merged last time
* at91 rtc driver changes related to the at91 cleanups
* ARM perf driver changes from Will Deacon
* updates for the brcmstb_gisb driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MwMG
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
Make the serial_mctrl_gpio driver the first user of the new gpiod_set_array
function, which is now available in the linux-gpio devel tree.
All modem control output signals are now set simultaneously.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The tty_kref_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions put_device() and tty_kref_put() test whether their argument
is NULL and then return immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 19e2ad6a09 ("n_tty: Remove overflow
tests from receive_buf() path") moved the increment of read_head into
the arguments list of read_buf_addr(). Function calls represent a
sequence point in C. Therefore read_head is incremented before the
character c is placed in the buffer. Since the circular read buffer is
a lock-less design since commit 6d76bd2618
("n_tty: Make N_TTY ldisc receive path lockless"), this creates a race
condition that leads to communication errors.
This patch modifies the code to increment read_head _after_ the data
is placed in the buffer and thus fixes the race for non-SMP machines.
To fix the problem for SMP machines, memory barriers must be added in
a separate patch.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds suspend/resume support for the of-serial driver
to provide power management support on devices attatched.
The handling may vary since not every of_serial device is
an 8250 port. Currently only 8250 port handling is added
in the suspend/resume function based on the type switch.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Joseph Lo <josephl@nvidia.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Florina Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2dea53bf57.
Turns out to be broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 513e438581.
It's broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Joseph Lo <josephl@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:
SysRq :
BUG: spinlock trylock failure on UP on CPU#0, swapper/0
lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
Call Trace:
<IRQ> [<ffffffff812c8d27>] dump_stack+0x19/0x1b
[<ffffffff8106812e>] spin_dump+0x7e/0xd0
[<ffffffff810681a6>] spin_bug+0x26/0x30
[<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
[<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
[<ffffffff812336d8>] serial8250_console_write+0x68/0x190
[<ffffffff811eb0b0>] ? sprintf+0x40/0x50
[<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
[<ffffffff8106b276>] console_unlock+0x3e6/0x490
[<ffffffff8106b595>] vprintk_emit+0x275/0x530
[<ffffffff812c869a>] printk+0x4d/0x4f
[<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
[<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
[<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
[<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
[<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
[<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
[<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
[<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
[<ffffffff8106da01>] handle_irq_event+0x41/0x70
[<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
[<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
[<ffffffff810041c2>] handle_irq+0x22/0x40
[<ffffffff812d096e>] do_IRQ+0x4e/0xf0
[<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
<EOI> [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
[<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
[<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
[<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
[<ffffffff812c726e>] rest_init+0xbe/0xd0
[<ffffffff816a4dcb>] start_kernel+0x339/0x346
[<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...
Before ebade5e833 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1. Restore that
behavior.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since most drivers interpret UPIO_MEM32 to mean "little-endian" and use
readl/writel to access the registers, add a parallel UPIO_MEM32BE to
request the use of big-endian MMIO accessors (ioread32be/iowrite32be).
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardcoded FIFO size can cause hardware performance limitation.
Using real size value provides better FIFO usage.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have fifosize set in driver data we prefer to use it instead of default
fifosize value (which is always 16). If there is defined fifosize for particular
serial we prefer to use it, otherwise we use value from info, which is
common for all serials on given platform.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds waiting until transmit buffer and shifter will be empty
before clock disabling.
Without this fix it's possible to have clock disabled while data was
not transmited yet, which causes unproper state of TX line and problems
in following data transfers.
Cc: <stable@vger.kernel.org> # v2.6.26+
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty break and error flags are not bit masks so do not to use bitwise
OR when assigning them.
Note that there is no functional change due to the if-else construct and
flag having been initialised to zero (TTY_NORMAL).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original driver fixed the io address with 0xe000+idx*8,
but real io address assigned from BIOS is dynamically from
read PCI configure space 0x24, 0x20, 0x1c.
The Fintek F81504/F81508/F81512 maybe malfunction without
this patch and malfunction surely when more then 1 PCI card.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tx_empty() should test whether both the transmitter fifo and shifter
for the port is empty, ie. the whole last char was transmitted.
The shift register is empty if AUART_STAT_BUSY is cleared.
The patch fixes the function against the shift register.
According to i.MX23 and i.MX28 Reference Manual:
AUART_STAT_TXFE:
TX FIFO or transmit holding register is empty.
AUART_STAT_BUSY:
AUART still transmits bits.
The BUSY signal goes HIGH as soon as the data is written to the
transmit FIFO (that is, the FIFO is non-empty) and remains asserted
HIGH while data is being transmitted.
BUSY is negated only when the transmit FIFO is empty, and the last
character has been transmitted from the shift register, including
the stop bits.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxs_auart_modem_status() did't detect gpio's state change
because s->mctrl_prev was modified before by mctrl_gpio_get().
The patch introduces mctrl_temp variable to fix the bug.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 732a84a037 ("serial: core: Pass termios to set_ldisc() notifications")
changed the set_ldisc prototype.
At the time of this commit the mxs_auart driver did not implement set_ldisc,
so that's why it has not been converted.
Adapt also mxs_auart_set_ldisc() so that the following build warning can be
fixed:
drivers/tty/serial/mxs-auart.c:962:2: warning: initialization from
incompatible pointer type
.set_ldisc = mxs_auart_set_ldisc,
^
drivers/tty/serial/mxs-auart.c:962:2: warning: (near initialization
for 'mxs_auart_ops.set_ldisc')
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable. Also the OCTEON simulation environments
prohibit 8-bit accesses.
For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.
We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_IMX_CONSOLE=n and CONFIG_CONSOLE_POLL=y we get the following
build warning:
drivers/tty/serial/imx.c:306:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:315:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
imx_port_ucrs_save/restore are only used under CONFIG_SERIAL_IMX_CONSOLE, so
their definitions should be also be protected only by CONFIG_SERIAL_IMX_CONSOLE.
This was detected when building 'allmodconfig'.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
Since of_alias_get_id() and pdev->id can get negative I check for the
error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
I (wrongly) assumed that line is an int and compiler didn't complain nor
did sparse. Since of_alias_get_id() and pdev->id can get negative I
check for the error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mcb_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in CSR A7DA SoC, uart6 located at BT module and it need multiple clock
sources, so for "sirf,marco-bt-uart" compatible uarts, drivers take 3
clock sources and enable them.
this patch also replaces clk_get by devm_clk_get function and fix DT
binding document in which we missed to fix when we added marco platform
in commit 909102db44 "serial: sirf: add support for Marco chip".
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the pr_warning to the more common pr_warn.
Other miscellanea:
o Convert unusual PR_FMT define and uses to pr_fmt
o Remove unnecessary OOM message
o Fix grammar in an error message
o Convert a pr_warning with a KERN_ERR to pr_err
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit deals with the checkpatch warning "Unnecessary space before
function pointer arguments".
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The changed function flushes the tx UART and the '4' corresponds to the
UART_FCR_CLEAR_XMIT value. This commit replaces the magic number with
this define.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the alignment of the 'case's i the switch statement.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flow of {neo,cls}_param() shows that at this stage the baud rate
has a non-zero value. This fact makes the if clausule obsolete and
acknowledges it's removal.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'force' parameter to the {cls,neo}_send_break() function has been
removed because it has not been used. The client to this API (the tty
code) always called this function with only one value.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes negative values of error rate to be checked, because these
values are valid as error rate. And this changes in the process of adopting
a value close to 0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2dea53bf57.
Turns out to be broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there isn't a DT alias then of_alias_get_id() will return
-ENODEV. This will cause the msm_serial driver to fail probe,
when we want to keep the previous behavior where we generated a
dynamic line number at probe time. Restore this behavior by
generating a dynamic id if the line number is still negative
after checking for an alias or in the non-DT case looking at the
.id field of the platform device.
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 68952076e9 ("vt: Remove
vt_get_kmsg_redirect() from uapi header") fails to compile if
!CONFIG_VT_CONSOLE.
Move macro definition for vt_get_kmsg_redirect() up with file-scope
function declarations.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos7 has a similar serial controller to that present in older Samsung
SoCs. To re-use the existing serial driver on Exynos7 we need to have
SERIAL_SAMSUNG_UARTS_4 and SERIAL_SAMSUNG_UARTS selected. This is not
possible because these symbols are dependent on PLAT_SAMSUNG which is
not present for the ARMv8 based exynos7.
Change the dependency of these symbols from PLAT_SAMSUNG to the serial
driver thus making it available on exynos7. As the existing platform
specific code making use of these symbols is related to uart driver this
change in dependency should not cause any issues.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fix spelling typo in printk and Kconfig within
various part of kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 1bd8324535.
To quote Olof:
This commit broke a whole lot of tegra boards in last night's
-next here. In particular, I've been looking at
tegra20-seaboard, which now doesn't boot with console any more.
Breaking existing systems is bad.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add equivalent attributes to those provided in the platform data
for use when RX DMA is enabled.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the DMA engine doesn't support residue processing then the RX DMA
handling won't work terribly well if polling is enabled. So, disable
RX DMA if residue handling isn't available.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA engines on some systems require that the dma_length is set
when using scatter gather lists.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing code assumed that PL011_DMA_BUFFER_SIZE == UART_XMIT_SIZE,
which may not always be the case. This allows for these two being
different sizes and not copying too much data.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating with __GFP_DMA avoids the need for bounce buffers
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no real value in displaying "serial: Freescale lpuart driver" in every
boot.
The uart_register_driver() can fail and even so the "serial: Freescale lpuart
driver" will be displayed, which is not really helpful.
This is particularly annoying when booting multi_v7_defconfig kernel on a SoC
that is not a Vybrid/Layerscape and even though this message gets displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'res' will be automatically checked inside devm_ioremap_resource(), so there is
no need to explicitly perform a NULL check.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit removes the address of Free Software Foundation from each
of the mentioned file in order to suppress the checkpatch warning.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enables support for the Digi Classic adapters line in the
jsm driver. This means changes in:
- device probing code
- device cleanup code
- driver description (Kconfig)
The init/cleanup code is based on the staging/dgnc driver.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the Digi Classic board implementation to the
staging/jsm driver.
The code here is taken from the staging/dgnc driver and modified to
match the serial/jsm state. This work is mostly based on the changes
that has been done to the code handling the Digi Neo cards with the
inspiration coming from the diff between staging/dgnc and serial/jsm
as well as the LKML history for the jsm_neo.c
The code compiles now and has no sparse and checkpatch errors or
warnings.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Simek