After moving a VPE from a redistributor to another, we're still left
with a potential pending doorbell interrupt on the old redistributor.
That interrupt should be moved to the new one to be either cleared
or take, depending on what the hypervisor wishes to do.
So let's move it right after having execited VMOVP. This doesn't
add much cost in the !DirectLPI case (we trade a DISCARD for a MOVI),
and the cost of the DIRECTLPI case should be minimal (two extra MMIO
accesses).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we don't have the DirectLPI feature, we must work around the
architecture shortcomings to be able to perform the required
maintenance (interrupt masking, clearing and injection).
For this, we create a fake device whose sole purpose is to
provide a way to issue commands as if we were dealing with LPIs
coming from that device (while they actually originate from
the ITS). This fake device doesn't have LPIs allocated to it,
but instead uses the VPE LPIs.
Of course, this could be a real bottleneck, and a naive
implementation would require 6 commands to issue an invalidation.
Instead, let's allocate at least one event per physical CPU
(rounded up to the next power of 2), and opportunistically
map the VPE doorbell to an event. This doorbell will be mapped
until we roll over and need to reallocate this slot.
This ensures that most of the time, we only need 2 commands
to issue an INV, INT or CLEAR, making the performance a lot
better, given that we always issue a CLEAR on entry, and
an INV on each side of a trapped WFI.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The normal course of action when allocating the ITS' view of a
device is to allocate the corresponding LPIs. But we're about
to introduce devices that borrow their interrupts from
some other entities.
So let's make the allocation optional.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When masking/unmasking a doorbell interrupt, it is necessary
to issue an invalidation to the corresponding redistributor.
We use the DirectLPI feature by writting directly to the corresponding
redistributor.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we're about to run a vcpu, it is crucial that the redistributor
associated with the physical CPU is being told about the new residency.
This is abstracted by hijacking the irq_set_affinity method for the
doorbell interrupt associated with the VPE. It is expected that the
hypervisor will call this method before scheduling the VPE.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a guest issues a INVALL command targetting a collection, it must
be translated into a VINVALL for the VPE that has this collection.
This patch implements a hook that offers this functionallity to the
hypervisor.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VPE is scheduled to run, the corresponding redistributor must
be told so, by setting VPROPBASER to the VM's property table, and
VPENDBASER to the vcpu's pending table.
When scheduled out, we preserve the IDAI and PendingLast bits. The
latter is specially important, as it tells the hypervisor that
there are pending interrupts for this vcpu.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On activation, a VPE is mapped using the VMAPP command, followed
by a VINVALL for a good measure. On deactivation, the VPE is
simply unmapped.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When creating a VM, the low level GICv4 code is responsible for:
- allocating each VPE a unique VPEID
- allocating a doorbell interrupt for each VPE
- allocating the pending tables for each VPE
- allocating the property table for the VM
This of course has to be reversed when the VM is brought down.
All of this is wired into the irq domain alloc/free methods.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the basic GICv4 VPE (vcpu in GICv4 parlance) infrastructure
(irqchip, irq domain) that is going to be populated in the following
patches.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When a VLPI is reconfigured (enabled, disabled, change in priority),
the full configuration byte must be written, and the caches invalidated.
Also, when using the irq_mask/irq_unmask methods, it is necessary
to disable the doorbell for that particular interrupt (by mapping it
to 1023) on top of clearing the Enable bit.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to let a VLPI being injected into a guest, the VLPI must
be mapped using the VMAPTI command. When moved to a different vcpu,
it must be moved with the VMOVI command.
These commands are issued via the irq_set_vcpu_affinity method,
making sure we unmap the corresponding host LPI first.
The reverse is also done when the VLPI is unmapped from the guest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the skeleton irq_set_vcpu_affinity method that will be used
to configure VLPIs.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the new GICv4 ITS command definitions, most of them, being
defined in terms of their physical counterparts.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch introduces a new header providing accessor functions for the
MIPS Global Interrupt Controller (GIC) mirroring those provided for the
other 2 components of the MIPS Coherent Processing System (CPS) - the
Coherence Manager (CM) & Cluster Power Controller (CPC).
This header makes use of the new standardised CPS accessor macros where
possible, but does require some custom accessors for cases where we have
either a bit or a register per interrupt.
A major advantage of this over the existing
include/linux/irqchip/mips-gic.h definitions is that code performing
accesses can become much simpler, for example this:
gic_update_bits(GIC_REG(SHARED, GIC_SH_SET_TRIGGER) +
GIC_INTR_OFS(intr), 1ul << GIC_INTR_BIT(intr),
(unsigned long)trig << GIC_INTR_BIT(intr));
...can become simply:
change_gic_trig(intr, trig);
The accessors handle 32 vs 64 bit in the same way as for CM & CPC code,
which means that GIC code will also not need to worry about the access
size in most cases. They are also accessible outside of
drivers/irqchip/irq-mips-gic.c which will allow for simplification in
the use of the non-interrupt portions of the GIC (eg. counters) which
currently require the interrupt controller driver to expose helper
functions for access.
This patch doesn't change any existing code over to use the new
accessors yet, since a wholesale change would be invasive & difficult to
review. Instead follow-on patches will convert code piecemeal to use
this new header. The one change to existing code is to rename gic_base
to mips_gic_base & make it global, in order to fit in with the naming
expected by the standardised CPS accessor macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17020/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c2 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c2 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.19.x-
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.
In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Up until now we have open-coded checks for whether CPUs are siblings,
with slight variations on whether we consider the package ID or not.
This will only get more complex when we introduce cluster support, so in
preparation for that this patch introduces a cpus_are_siblings()
function which can be used to check whether or not 2 CPUs are siblings
in a consistent manner.
By checking globalnumber with the VP ID masked out this also has the
neat side effect of being ready for multi-cluster systems already.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h
when declaring macros corresponding to register fields. This patch
modifies our definitions to do so.
The *_SHF definitions are removed entirely - they duplicate information
found in the masks, are infrequently used & can be replaced with use of
__ffs() where needed.
The *_MSK definitions then lose their _MSK suffix which is now somewhat
redundant, and users are modified to match.
The field definitions are moved to follow the appropriate register's
accessor functions, which helps to keep the field definitions in order &
to find the appropriate fields for a given register. Whilst here a
comment is added describing each register & including its name, which is
helpful both for linking the register back to hardware documentation &
for grepping purposes.
This also cleans up a couple of issues that became obvious as a result
of making the changes described above:
- We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony
copy of that named GCR_RESET_EXT_BASE - a register which does not
exist. The bad definitions were added by commit 497e803ebf ("MIPS:
smp-cps: Ensure secondary cores start with EVA disabled") and made
use of from boot_core(), which is now modified to use the
GCR_Cx_RESET_EXT_BASE definitions.
- We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly
define this as inFo rather than inGo.
Now that we don't duplicate field information between _SHF & _MSK
definitions, and keep the fields next to the register accessors, it will
be much easier to spot & prevent any similar oddities being introduced
in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17001/
Patchwork: https://patchwork.linux-mips.org/patch/17216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We're are going to need to change a bit more than just the enable
bit in the LPI property table in the future. So let's change the
LPI configuration funtion to take a set of bits to be cleared,
and a set of bits to be set.
This way, we'll be able to use it when a guest updates an LPI
property (priority, for example).
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we want to use 2-level tables for VCPUs, let's hack the device
table allocator in order to make it slightly more generic. It
will get reused in subsequent patches.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rework LPI deallocation so that it can be reused by the v4 support
code.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just as for the property table, let's move the pending table
allocation to a separate function.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VCPU tables can be quite sparse as well, and it makes sense
to use indirect tables as well if possible.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move the LPI property table allocation into its own function, as
this is going to be required for those associated with VMs in
the future.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Allow the pending state of an LPI to be set or cleared via
irq_set_irqchip_state.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Most ITS commands do operate on a collection object, and require
a SYNC command to be performed on that collection in order to
guarantee the execution of the first command.
With GICv4 ITS, another set of commands perform similar operations
on a VPE object, and a VSYNC operations must be executed to guarantee
their execution.
Given the similarities (post a command, perform a synchronization
operation on a sync object), it makes sense to reuse the same
mechanism for both class of commands.
Let's start with turning its_send_single_command into a huge macro
that performs the bulk of the work, and a set of helpers that
make this macro usable for the GICv3 ITS commands.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the probing code for the ITS VLPI support. This includes
configuring the ITS number if not supporting the single VMOVP
command feature.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The various LPI definitions are in the middle of the code, and
would be better placed at the beginning, given that we're going
to use some of them much earlier.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add helper functions that probe for VLPI and DirectLPI properties.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to discover the VLPI properties, we need to iterate over
the redistributor regions. As we already have code that does this,
let's factor it out and make it slightly more generic.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee@kernel.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
wait_for_range_completion() is nicely busted when handling
wrapping of the command queue, leading to an early exit
instead of waiting for the command to have been executed.
Fortunately, the impact is pretty minor, as it only impair
the detection of an ITS that doesn't make any forward progress
for a whole second. And an ITS should *never* lock up.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Armada XP does not only support MSI, but also MSI-X. This patch sets
the MSI_FLAG_PCI_MSIX flag in the interrupt controller driver which
is the only change necessary to enable MSI-X support on this SoC. As
the Linux PCI MSI-X infrastructure takes care of writing the data and
address structures into the BAR specified by the MSI-X controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The xtensa-mx driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-13-marc.zyngier@arm.com
The MIPS GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-12-marc.zyngier@arm.com
The HIP04 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-11-marc.zyngier@arm.com
The metag-ext driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-10-marc.zyngier@arm.com
The BCM 7038-L1 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-9-marc.zyngier@arm.com
The BCM 6345-L1 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-8-marc.zyngier@arm.com
The Armada 370 XP driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-7-marc.zyngier@arm.com
The GICv3 ITS driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-6-marc.zyngier@arm.com
The GICv3 driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-5-marc.zyngier@arm.com
The GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-4-marc.zyngier@arm.com
While parsing the msi-parent property to chase up the IRQ domain
a given device belongs to, the index into the msi-parent tuple should
be incremented to ensure all properties entries are taken into account.
Current code missed the index update so the parsing loop does not work
in case multiple msi-parent phandles are present and may turn into
an infinite loop in of_pmsi_get_dev_id() if phandle at index 0 does
not correspond to the domain we are actually looking-up.
Fix the code by updating the phandle index at each iteration in
of_pmsi_get_dev_id().
Fixes: deac7fc1c8 ("irqchip/gic-v3-its: Parse new version of msi-parent property")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When enabling ITS NUMA support on D05, I got the boot log:
[ 0.000000] SRAT: PXM 0 -> ITS 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 1 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 2 -> Node 0
[ 0.000000] SRAT: PXM 1 -> ITS 3 -> Node 1
[ 0.000000] SRAT: ITS affinity exceeding max count[4]
This is wrong on D05 as we have 8 ITSs with 4 NUMA nodes.
So dynamically alloc the memory needed instead of using
its_srat_maps[MAX_NUMNODES], which count the number of
ITS entry(ies) in SRAT and alloc its_srat_maps as needed,
then build the mapping of numa node to ITS ID. Of course,
its_srat_maps will be freed after ITS probing because
we don't need that after boot.
After doing this, I got what I wanted:
[ 0.000000] SRAT: PXM 0 -> ITS 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 1 -> Node 0
[ 0.000000] SRAT: PXM 0 -> ITS 2 -> Node 0
[ 0.000000] SRAT: PXM 1 -> ITS 3 -> Node 1
[ 0.000000] SRAT: PXM 2 -> ITS 4 -> Node 2
[ 0.000000] SRAT: PXM 2 -> ITS 5 -> Node 2
[ 0.000000] SRAT: PXM 2 -> ITS 6 -> Node 2
[ 0.000000] SRAT: PXM 3 -> ITS 7 -> Node 3
Fixes: dbd2b82672 ("irqchip/gic-v3-its: Add ACPI NUMA node mapping")
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Cc: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Broadcom STB platforms support S5 and we allow specific hardware
wake-up events to take us out of this state. Because we were not
defining an irq_pm_shutdown() function pointer, we would not be
correctly masking non-wakeup events, which would result in spurious
wake-ups from sources that were not explicitly configured for wake-up.
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Devices that expose their interrupt status registers via system
registers (e.g. Statistical profiling, CPU PMU, DynamIQ PMU, arch timer,
vgic (although unused by Linux), ...) rely on a context synchronising
operation on the CPU to ensure that the updated status register is
visible to the CPU when handling the interrupt. This usually happens as
a result of taking the IRQ exception in the first place, but there are
two race scenarios where this isn't the case.
For example, let's say we have two peripherals (X and Y), where Y uses a
system register for its interrupt status.
Case 1:
1. CPU takes an IRQ exception as a result of X raising an interrupt
2. Y then raises its interrupt line, but the update to its system
register is not yet visible to the CPU
3. The GIC decides to expose Y's interrupt number first in the Ack
register
4. The CPU runs the IRQ handler for Y, but the status register is stale
Case 2:
1. CPU takes an IRQ exception as a result of X raising an interrupt
2. CPU reads the interrupt number for X from the Ack register and runs
its IRQ handler
3. Y raises its interrupt line and the Ack register is updated, but
again, the update to its system register is not yet visible to the
CPU.
4. Since the GIC drivers poll the Ack register, we read Y's interrupt
number and run its handler without a context synchronisation
operation, therefore seeing the stale register value.
In either case, we run the risk of missing an IRQ. This patch solves the
problem by ensuring that we execute an ISB in the GIC drivers prior
to invoking the interrupt handler. This is already the case for GICv3
and EOIMode 1 (the usual case for the host).
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The version check was added due to dependency to
a618c7f89a ACPICA: Add support for new SRAT subtable
Now, that this code is in the kernel, remove the check. This is esp.
useful to enable backports.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: keescook@chromium.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500149266-32357-11-git-send-email-Julia.Lawall@lip6.fr
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: keescook@chromium.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500149266-32357-7-git-send-email-Julia.Lawall@lip6.fr
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: keescook@chromium.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500149266-32357-6-git-send-email-Julia.Lawall@lip6.fr
Since commit d59f6617ee ("genirq: Allow fwnode to carry name
information only") the irqdomain core sets the names of irq domains.
When the name is allocated the new IRQ_DOMAIN_NAME_ALLOCATED flag is
set. Replacing the allocated name with a constant one is not a good
idea, since calling the new irq_domain_update_bus_token() API, added to
the MIPS GIC driver by commit 96f0d93a48 ("irqchip/MSI: Use
irq_domain_update_bus_token instead of an open coded access") will
attempt to kfree the pointer, and result in a kernel OOPS.
Fix this by removing the names, now that they are set by the irqdomain
core. This effectively reverts commit 21c57fd135 ("irqchip/mips-gic:
Populate irq_domain names").
Fixes: d59f6617ee ("genirq: Allow fwnode to carry name information only")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500363561-32213-1-git-send-email-matt.redfearn@imgtec.com
Honor the 'force' flag for set_affinity, by selecting a CPU
from the given mask (which may not be reported "online" by
the cpu_online_mask). Some drivers, like ARM PMU, rely on it.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the GIC cannot map an IRQ via irq_domain_ops->alloc(), it doesn't
return an error code. This can cause a problem with drivers, where
it thinks it has successfully got an IRQ for the device, but requesting
the same ends up failure with -ENOSYS (as the IRQ's chip is not set).
Fixes: commit 443acc4f37 ("irqchip: GICv3: Convert to domain hierarchy")
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the GIC cannot map an IRQ via irq_domain_ops->alloc(), it doesn't
return an error code. This can cause a problem with drivers, where
it thinks it has successfully got an IRQ for the device, but requesting
the same ends up failure with -ENOSYS (as the IRQ's chip is not set).
Fixes: commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq domain.")
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We are no longer using the root argument passed to the ->fixup() hooks.
Remove it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_find_compatible_node() is calling of_node_put() on its first argument
thus leading to an unbalanced of_node_get/put() issue if the node has not
been retained before that.
Instead of passing the root node, pass NULL, which does exactly the same:
iterate over all DT nodes, starting from the root node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: 3d61467f9b ("irqchip: atmel-aic: Implement RTC irq fixup")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
aic_common_irq_fixup() is calling twice of_node_put() on the same node
thus leading to an unbalanced refcount on the root node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: b2f579b58e ("irqchip: atmel-aic: Add irq fixup infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- Expand the generic infrastructure handling the irq migration on CPU
hotplug and convert X86 over to it. (Thomas Gleixner)
Aside of consolidating code this is a preparatory change for:
- Finalizing the affinity management for multi-queue devices. The
main change here is to shut down interrupts which are affine to a
outgoing CPU and reenabling them when the CPU comes online again.
That avoids moving interrupts pointlessly around and breaking and
reestablishing affinities for no value. (Christoph Hellwig)
Note: This contains also the BLOCK-MQ and NVME changes which depend
on the rework of the irq core infrastructure. Jens acked them and
agreed that they should go with the irq changes.
- Consolidation of irq domain code (Marc Zyngier)
- State tracking consolidation in the core code (Jeffy Chen)
- Add debug infrastructure for hierarchical irq domains (Thomas
Gleixner)
- Infrastructure enhancement for managing generic interrupt chips via
devmem (Bartosz Golaszewski)
- Constification work all over the place (Tobias Klauser)
- Two new interrupt controller drivers for MVEBU (Thomas Petazzoni)
- The usual set of fixes, updates and enhancements all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
irqchip/or1k-pic: Fix interrupt acknowledgement
irqchip/irq-mvebu-gicp: Allocate enough memory for spi_bitmap
irqchip/gic-v3: Fix out-of-bound access in gic_set_affinity
nvme: Allocate queues for all possible CPUs
blk-mq: Create hctx for each present CPU
blk-mq: Include all present CPUs in the default queue mapping
genirq: Avoid unnecessary low level irq function calls
genirq: Set irq masked state when initializing irq_desc
genirq/timings: Add infrastructure for estimating the next interrupt arrival time
genirq/timings: Add infrastructure to track the interrupt timings
genirq/debugfs: Remove pointless NULL pointer check
irqchip/gic-v3-its: Don't assume GICv3 hardware supports 16bit INTID
irqchip/gic-v3-its: Add ACPI NUMA node mapping
irqchip/gic-v3-its-platform-msi: Make of_device_ids const
irqchip/gic-v3-its: Make of_device_ids const
irqchip/irq-mvebu-icu: Add new driver for Marvell ICU
irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP
dt-bindings/interrupt-controller: Add DT binding for the Marvell ICU
genirq/irqdomain: Remove auto-recursive hierarchy support
irqchip/MSI: Use irq_domain_update_bus_token instead of an open coded access
...
- Potential out of bound access for GICv3
- Memory allocation gotcha in the Marvell GICP driver
- Fix openrisc interrupt acknowledgement
-----BEGIN PGP SIGNATURE-----
iQJJBAABCAAzFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAllWYioVHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJECPQ0LrRPXpD7xAP/1b6jLrnslzq6gP/lTKXVyqlCk/H
2ylkwo44Cvj+nZsUJG7Wq3lFrJ+XgnzoMAxtTWKzKvKGKObt89eFRo2iv1t4VFd+
UKsVKMnMfMOl6qQly4qCZx4JpgAUYsxLn7Uo1/mO/sFI80KLQhsRDPMTu5qsEVoS
ma5BGYx1LhIz3Gd3WBO+6J730W1T0/xbNM8rz1PIPgfIGe+7MlV0y6aBswl6PVeJ
ei036Jtq5v/9p7yFmS7Mk4NBnAHDyJpwJdZiIPNSo5m3ngshyJJ/zDo0wM+FzW79
pHdba2yTPixXYPoGyvL1Pu7ha/94AwYtiBdxtG+LfkAqY+uYrZuNHURAcqvP7xBx
yR7ZLwXwzM8vqW8OiLSiNA6X/4+jjwR9NQ3jh7FhFWYRzW+ohcDoAiPA6bntmNUZ
59LJZ/CWkv7rISwHyJRvXdCFdmS+h99EXiETtdJVDhdk+1axRxKglXoTEBHur8BG
U8rPN2SOFym2OaAQrMm9nIrG7bXxcfElJl4ygN8K+p1FsMMGDzsYAKr1XcsNdo0r
E4HLxUZ20OzsKXOVPjta096jf/kPDiFP1u1X/33KjJKZyUMikflqtzKDqT+Ek4oV
GtO5cuA79Jm8/MjECR1ZEwpDUbPQEPSn3AyRTvkwCxMzeMVHKRCyGv4RIzf3UJms
vCVA+e1xgln8/p58
=sOY7
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Merge second batch of irqchip updates for 4.13 from Marc Zyngier
- Potential out of bound access for GICv3
- Memory allocation gotcha in the Marvell GICP driver
- Fix openrisc interrupt acknowledgement
Usually, hardware implicitly acknowledges interrupts when
reading them. However, if this is not the case, the IRQ
gets fired over and over again in the current implementation.
This patch uses the right mask acknowledge function to handle the
aforementioned situation on or1k processors that interact with
such kind of hardware.
Acked-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Pedro H. Penna <pedrohenriquepenna@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
BITS_TO_LONGS() gives us the number of longs we need, but we want to
allocate the number of bytes.
Fixes: a68a63cb4d ("irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP")
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- support for the new Marvell wire-to-MSI bridge
- support for the Aspeed I2C irqchip
- Armada XP370 per-cpu interrupt fixes
- GICv3 ITS ACPI NUMA support
- sunxi-nmi cleanup and updates for new platform support
- various GICv3 ITS cleanups and fixes
- some constifying in various places
-----BEGIN PGP SIGNATURE-----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=CAfw
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for v4.13 from Marc Zyngier
- support for the new Marvell wire-to-MSI bridge
- support for the Aspeed I2C irqchip
- Armada XP370 per-cpu interrupt fixes
- GICv3 ITS ACPI NUMA support
- sunxi-nmi cleanup and updates for new platform support
- various GICv3 ITS cleanups and fixes
- some constifying in various places
The current ITS driver is assuming every ITS hardware implementation
supports minimum of 16bit INTID. But this is not true, as per GICv3
specification, INTID field is IMPLEMENTATION DEFINED in the range of
14-24 bits. We might see an unpredictable system behavior on systems
where hardware support less than 16bits and software tries to use
64K LPI interrupts.
On Qualcomm Datacenter Technologies QDF2400 platform, boot log shows
confusing information about number of LPI chunks as shown below. The
QDF2400 ITS hardware supports 24bit INTID.
This patch allocates the memory resources for PEND/PROP tables based
on discoverable value which is specified in GITS_TYPER.IDbits. Also
it fixes the log message that reflects the correct number of LPI
chunks were allocated.
ITS@0xff7efe0000: allocated 524288 Devices @3c0400000 (indirect, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Interrupt Collections @3c0130000 (flat, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Virtual CPUs @3c0140000 (flat, esz 8, psz 64K, shr 1)
ITS: Allocated 524032 chunks for LPIs
PCI/MSI: ITS@0xff7efe0000 domain created
Platform MSI: ITS@0xff7efe0000 domain created
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add code to parse SRAT ITS Affinity sub table as defined in ACPI 6.2.
Later in per device probe, ITS devices are mapped to numa node using
ITS Id to proximity domain mapping.
[maz: fix dependency on ACPICA, fixed structure name, minor cleanups]
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.
Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.
The driver was initially written by Hanna Hawa <hannah@marvell.com>.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we have irq_domain_update_bus_token(), switch everyone over
to it. The debugfs code thanks you for your continued support.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Aspeed 24XX/25XX chips share a single hardware interrupt across 14
separate I2C busses. This adds a dummy irqchip which maps the single
hardware interrupt to software interrupts for each of the busses.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In addition to introducing the new compatible string the bindings
description is reworked to be more generic.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This reverts commit 353d6d6c82, which is
no longer needed, now that the irq-armada-370-xp driver properly
re-enables per-CPU interrupt on both the boot CPU and secondary CPUs
after resume.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit d17cab4451 ("irqchip: Kill off set_irq_flags usage") changed
the code of armada_370_xp_mpic_irq_map() from using set_irq_flags() to
irq_set_probe().
While the commit log seems to imply that there are no functional
changes, there are indeed functional changes introduced by this commit:
the IRQ_NOAUTOEN flag is no longer cleared. This functional change
caused a regression on Armada XP, which no longer works properly after
suspend/resume because per-CPU interrupts remain disabled. This
regression was temporarly worked around in commit
353d6d6c82 ("irqchip/armada-370-xp: Fix regression by clearing
IRQ_NOAUTOEN"), but it is not the most satisfying solution. This commit
implements the solution that was initially discussed with Thomas
Gleixner.
Due to how the hardware registers work, the irq-armada-370-xp cannot
simply save/restore a bunch of registers at suspend/resume to make sure
that the interrupts remain in the same state after resuming. Therefore,
it relies on the kernel to say whether the interrupt is disabled or not,
using the irqd_irq_disabled() function. This was all working fine while
the IRQ_NOAUTOEN flag was cleared.
With the change introduced by Rob Herring in d17cab4451, the
IRQ_NOAUTOEN flag is now set for all interrupts. irqd_irq_disabled()
returns false for per-CPU interrupts, and therefore our per-CPU
interrupts are no longer re-enabled after resume.
This commit fixes that by using irqd_irq_disabled() only for global
interrupts, and using the newly introduced irq_percpu_is_enabled() for
per-CPU interrupts.
Also, it fixes a related problems that per-CPU interrupts were only
re-enabled on the boot CPU and not other CPUs. Until now this wasn't a
problem since on this platform, only the local timers are using per-CPU
interrupts and the local timers of secondary CPUs are turned off/on
during CPU hotplug before suspend, after after resume. However, since
Linux 4.4, we are also be using per-CPU interrupts for the network
controller, so we need to properly restore the per-CPU interrupts on
secondary CPUs as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since the overall logic of the driver to handle the global and per-CPU
masking of the interrupts is far from trivial, this commit adds a long
comment detailing how the hardware operates and what strategy the
driver implements on top of that.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to clarify to which register base the various register
definitions apply, this commit re-orders them, and adds a comment that
clearly indicate which registers are relative to "main_int_base" and
which registers are relative to "per_cpu_int_base".
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just skip the irq affinity setting when the target cpu is the same as
current setting.
This is a small optimization for irq affinity setting logic.
Signed-off-by: MaJun <majun258@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The call to pci_for_each_dma_alias() in the ITS PCI code has aroused
suspicion in the past, and upon closer inspection does turn out to be
completely backwards. Rather than iterating through each RID alias of
the given device, what we actually want to be doing here is iterating
through all the *other* devices which may also alias the same RID, in
order to size the table for the worst case.
Do the right thing by ignoring the initial DMA aliases themselves and
just using that walk to detect an aliasing bridge, then walking back
down the bus topology as necessary to actually count everything else.
Our alias handling still isn't perfect, since we don't account for the
cases of certain bridges only taking ownership of transactions under
particular circumstances, but without completely reworking the ITS code
to cope with the notion of multiple DevIDs per device, it'll have to do.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The R_INTC on the A31 is undocumented. It was previously supported
by the sun6i-a31-sc-nmi compatible. This compatible however required
the register region to start at the first used register, rather than
the boundaries laid out in the SoC's memory map. The new compatible
fixes the alignment, while also naming it properly.
Since the only difference between the old and new compatibles are
a fixed offset for the registers, and since the old one is deprecated,
this patch adds a set of register defines for the new compatible,
while modifying the old set to reference the new set minus a fixed
offset.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sunxi_sc_nmi_reg_offs, which hold the register offsets for the
various variants, is never modified, and only used at init time within
the init functions referenced by IRQCHIP_DECLARE, which themselves are
tagged __init.
Const-ify the sunxi_sc_nmi_reg_offs structures, and tag them as
__initconst.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a pure code move to reorder the various sunxi_sc_nmi_reg_offs'
by family and alphabetical order. No functionality changes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sunxi-nmi disables all its interrupts and clears any pending
interrupts at probe time.
Add comments documenting it, just to make it clear.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The sunxi-nmi driver has a bunch of raw register offsets and bit values.
Convert them into define macros for better readability.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gic_read_count(), gic_write_compare() and gic_write_cpu_compare() are
often used in a sequence to update the compare register with a count
value increased by a small offset.
With small delta values used to update the compare register, the time to
update function trace for these operations may be longer than the update
timeout leading to update failure.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1496991845-27031-1-git-send-email-marcin.nowakowski@imgtec.com
ACPI IORT is an ACPI addendum to describe the connection topology of
devices with IOMMUs and interrupt controllers on ARM64 ACPI systems.
Currently the ACPI IORT Kbuild symbol is selected whenever the Kbuild
symbol ARM_GIC_V3_ITS is enabled, which in turn is selected by ARM64
Kbuild defaults. This makes the logic behind ACPI_IORT selection a bit
twisted and not easy to follow. On ARM64 systems enabling ACPI the
kbuild symbol ACPI_IORT should always be selected in that it is a kernel
layer provided to the ARM64 arch code to parse and enable ACPI firmware
bindings.
Make the ACPI_IORT selection explicit in ARM64 Kbuild and remove the
selection from ARM_GIC_V3_ITS entry, making the ACPI_IORT selection
logic clearer to follow.
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support;
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector;
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5lPB
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
* tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: don't use linux IRQ #0
xtensa: reduce double exception literal reservation
xtensa: ISS: Use kmalloc_array() in simdisk_init()
xtensa: Use seq_puts() in c_show()
Linux IRQ #0 is reserved for error reporting and may not be used.
Increase NR_IRQS for one additional slot and increase
irq_domain_add_legacy parameter first_irq value to 1, so that linux
IRQ #0 is not associated with hardware IRQ #0 in legacy IRQ domains.
Introduce macro XTENSA_PIC_LINUX_IRQ for static translation of xtensa
PIC hardware IRQ # to linux IRQ #. Use this macro in XTFPGA platform
data definitions.
This fixes inability to use hardware IRQ #0 in configurations that don't
use device tree and allows for non-identity mapping between linux IRQ #
and hardware IRQ #.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Pull irq fixes from Thomas Gleixner:
"A set of small fixes for the irq subsystem:
- Cure a data ordering problem with chained interrupts
- Three small fixlets for the mbigen irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix chained interrupt data ordering
irqchip/mbigen: Fix the clear register offset calculation
irqchip/mbigen: Fix potential NULL dereferencing
irqchip/mbigen: Fix memory mapping code
The register array offset for clearing an interrupt is calculated by:
offset = (hwirq - RESERVED_IRQ_PER_MBIGEN_CHIP) / 32;
This is wrong because the clear register array includes the reserved
interrupts. So the clear operation ends up in the wrong register.
This went unnoticed so far, because the hardware clears the real bit
through a timeout mechanism when the hardware is configured in debug
mode. That debug mode was enabled on early generations of the hardware, so
the problem was papered over.
On newer hardware with updated firmware the debug mode was disabled, so the
bits did not get cleared which causes the system to malfunction.
Remove the subtraction of RESERVED_IRQ_PER_MBIGEN_CHIP, so the correct
register is accessed.
[ tglx: Rewrote changelog ]
Fixes: a6c2f87b88 ("irqchip/mbigen: Implement the mbigen irq chip operation functions")
Signed-off-by: MaJun <majun258@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linuxarm@huawei.com
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Link: http://lkml.kernel.org/r/1494561328-39514-4-git-send-email-guohanjun@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some mbigens share memory regions, and devm_ioremap_resource
does not allow to share resources which will break the probe
of mbigen, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but
with proper error handling and logging.
Fixes: 216646e4d8 ("irqchip/mbigen: Fix return value check in mbigen_device_probe()")
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linuxarm@huawei.com
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: MaJun <majun258@huawei.com>
Link: http://lkml.kernel.org/r/1494561328-39514-2-git-send-email-guohanjun@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). Use devm_ioremap_resource() instead of devm_ioremap()
to fix the IS_ERR() test issue.
Fixes: 76e1f77f9c ("irqchip/mbigen: Introduce mbigen_of_create_domain()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20170427152113.31147-1-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts") fixed
local interrupts by creating virq mappings for them all at startup.
Unfortunately this change broke legacy IRQ controllers in the same
system, such as the i8259 on the Malta platform, as it allocates virq
numbers that were expected to be available for the legacy controller.
Instead of creating the mappings statically when the GIC is probed,
re-introduce the irq domain .map function, removed by commit e875bd66df
("irqchip/mips-gic: Fix local interrupts") and use it to set up the irq
handler and chip. Since a good deal of the required functionality is
already implemented by gic_irq_domain_alloc, repurpose that function for
gic_irq_domain_map and add a new gic_irq_domain_alloc which wraps
gic_irq_domain_map with the necessary conversion.
This change fixes the legacy interrupt controller of the Malta platform
without breaking the perf interrupt fixed by commit e875bd66df
("irqchip/mips-gic: Fix local interrupts").
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-4-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Qais indicates that he felt having a separate device IRQ domain was
cleaner, but along with everyone else I'm aware of touching this driver
I disagree.
Remove the separate device IRQ domain so that we simply have the main
GIC IRQ domain used for devices, and an IPI IRQ domain as a child. The
logic for handling the device interrupts & IPIs is cleanly separated
into the appropriate domain ops, making it much easier to reason about
what the driver is doing than the previous approach where the 2 child
domains had to call up to their parent, which had to handle both types
of interrupt & had all sorts of weird & wonderful duplication or
outright clobbering of setup performed by multiple domains.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-3-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy
domain") introduced the GIC IPI IRQ domain we have tracked both
reservation of interrupts & their use with a single bitmap - ipi_resrv.
If an interrupt is reserved for use as an IPI but not actually in use
then the appropriate bit is set in ipi_resrv. If an interrupt is either
not reserved for use as an IPI or has been allocated as one then the
appropriate bit is clear in ipi_resrv.
Unfortunately this means that checking whether a bit is set in ipi_resrv
to prevent IPI interrupts being allocated for use with a device is
broken, because if the interrupt has been allocated as an IPI first then
its bit will be clear.
Fix this by separating the tracking of IPI reservation & usage,
introducing a separate ipi_available bitmap for the latter. This means
that ipi_resrv will now always have bits set corresponding to all
interrupts reserved for use as IPIs, whether or not they have been
allocated yet, and therefore that checking it when allocating device
interrupts works as expected.
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce support for registering an IPI IRQ domain suitable for use by
systems using the MIPS MT (multithreading) ASE within a single core.
This will allow for such systems to be supported generically, without
the current kludge of IPI code split between the MIPS arch & the malta
board support code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various struct irq_chip callbacks in the MIPS CPU interrupt
controller driver have been calculating the hardware interrupt number by
subtracting MIPS_CPU_IRQ_BASE from the virq number. This presumes a
linear mapping beginning from MIPS_CPU_IRQ_BASE, and this will not hold
once an IPI IRQ domain is introduced. Switch to using the hwirq field of
struct irq_data which already contains the hardware interrupt number
instead of attempting to calculate it.
Similarly, plat_irq_dispatch calculated the virq number by adding
MIPS_CPU_IRQ_BASE to the hardware interrupt number. Ready this for the
introduction of an IPI IRQ domain by instead using irq_linear_revmap.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace use of the magic number 0x100 (ie. bit 8) with the more
explanatory IE_SW0 (ie. interrupt enable for software interrupt 0) or
C_SW0 (ie. cause bit for software interrupt 0) as appropriate.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15834/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Clear OF_POPULATED flag, so that GPC power domain driver[1] can be
bound to "gpc" node as well.
[1] https://lkml.org/lkml/2017/3/28/835
Cc: yurovsky@gmail.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On sama5d2, VDD core may be cut while suspending to RAM. This means the
AIC5 registers content is lost. Restore it at resume time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In Mediatek SOCs, the CIRQ is a low power interrupt controller
designed to works outside MCUSYS which comprises with Cortex-Ax
cores,CCI and GIC.
The CIRQ controller is integrated in between MCUSYS( include
Cortex-Ax, CCI and GIC ) and interrupt sources as the second
level interrupt controller. The external interrupts which outside
MCUSYS will feed through CIRQ then bypass to GIC. CIRQ can monitors
all edge trigger interupts. When an edge interrupt is triggered,
CIRQ can record the status and generate a pulse signal to GIC when
flush command executed.
When system enters sleep mode, MCUSYS will be turned off to improve
power consumption, also GIC is power down. The edge trigger interrupts
will be lost in this scenario without CIRQ.
This commit provides the CIRQ irqchip implement.
Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Getting hold of the DevID requires us to call iort_pmsi_get_dev_id().
Since iort_pmsi_get_dev_id() may or may not be implemented, we
provide a weak function that acts as a stub.
The weak function will be removed when the ACPI counterpart is
merged.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the preparation of platform msi support and interrupt producer
in commit d44fa3d460 ("ACPI: Add support for ResourceSource/IRQ
domain mapping"), we can add mbigen ACPI support now.
Now that the major framework changes are ready, we just need to add
the ACPI probe code which creates the irqdomain for devices connecting
to it.
In order to create the irqdomain, we need to know the number of hw
irqs as input which is provided by mbigen. In DT case, we are using
"num-pins" property to describe it, and we will take advantage of
that too using _DSD in ACPI as there is no standard way of describe
it in ACPI way, also according to the _DSD rule described in
Documentation/acpi/DSD-properties-rules.txt, it doesn't break
the rules.
The DSDT is represented as below:
For mbigen,
Device(MBI0) {
Name(_HID, "HISI0152")
Name(_UID, Zero)
Name(_CRS, ResourceTemplate() {
Memory32Fixed(ReadWrite, 0xa0080000, 0x10000)
})
Name(_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"num-pins", 378}
}
})
}
For devices,
Device(SAS0) {
Name(_HID, "HISIxxxx")
Name(_UID, Zero)
Name(_CRS, ResourceTemplate() {
Memory32Fixed(ReadWrite, 0xb0030000, 0x10000)
Interrupt(ResourceConsumer,..., "\_SB.MBI0") {12, ...}
})
}
So for the devices connected to the mbigen, as we clearly say that
it refers to a specific interrupt controller (mbigen), we can get
the virq from mbigen's irqdomain once it's created successfully.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: MaJun <majun258@huawei.com>
Cc: Al Stone <ahs3@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce mbigen_of_create_domain() to consolidate OF related
code and prepare for ACPI later, no funtional change.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Ma Jun <majun258@huawei.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Module owner will be set by driver core, so drop it.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Ma Jun <majun258@huawei.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the introduction of its_pmsi_init_one(), support for ACPI
firmware interface can be plugged into the gicv3 ITS driver.
Add code to scan the MADT table to get the ITS entry(ies), then use
the information to create the platform msi domain for devices
connected to it, mirroring the ITS PCI MSI code path.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce its_pmsi_init_one() to separate firmware dependent
code (ie OF dependent code) and firmware agnostic code so
that gic3-its code can be made to support other firmware
bindings easily.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
By adding ACPI support for platform MSI, the gicv3 driver has to
provide code to retrieve the dev id through ACPI instead of device
tree bindings; given that its_pmsi_prepare() allows already to get
the dev id but it is OF dependent, factor OF related code out into
a single function to make its_pmsi_prepare() ready to be used with
other firmware interfaces.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rearrange header file includes in alphabetic order.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: fixed commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This prevent unnecessary visibility when configuring trigger type
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Originally driver only supports one base. However, MT6797 has
more than one bases to configure interrupt polarity. To support
possible design change, here comes a solution to use arbitrary
number of bases.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Moxa Art interrupt controller is very very likely just an instance
of the Faraday FTINTC010 interrupt controller from Faraday Technology.
An indication would be its close association with the FA526 ARM core
and the fact that the register layout is the same.
The implementation in irq-moxart.c can probably be right off replaced
with the irq-ftintc010.c driver by adding a compatible string, selecting
this irqchip from the machine and run.
As a bonus we have an irqchip driver supporting high/low and
rising/falling edges for the Moxa Art, and shared code with the Gemini
platform.
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The triggers in the driver were right for high level triggered
IRQs but the edge detection on edge triggered IRQs was wrong.
After studying a proper driver from Po-Yu Chuang I now know how
to handle these right, and we can properly implement low level
IRQs as well.
The device trees for the Gemini had polarity switched around
so these have been fixed to conform to the right polarity as
well.
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Gemini irqchip turns out to be a standard IP component from
Faraday Technology named FTINTC010 after some research and new
information.
- Rename the driver and all symbols to reflect the new information.
- Add the new compatible string "faraday,ftintc010"
- Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs
using this interrupt controller can easily select and reuse it
instead of hardwiring it to ARCH_GEMINI
I have created a separate patch to select the new Kconfig symbol
from the Gemini machine, which will be merged through the ARM
SoC tree.
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts") added
mapping of several local interrupts during initialisation of the gic
driver. This associates virq numbers with these interrupts.
Unfortunately, as not all of the interrupts are mapped in hardware
order, when drivers subsequently request these interrupts they conflict
with the mappings that have already been set up. For example, this
manifests itself in the gic clocksource driver, which fails to probe
with the message:
clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x7350c9738,
max_idle_ns: 440795203769 ns
GIC timer IRQ 25 setup failed: -22
This is because virq 25 (the correct IRQ number specified via device
tree) was allocated to the PERFCTR interrupt (and 24 to the timer, 26 to
the FDC). To fix this, map all of these local interrupts in the hardware
order so as to associate their virq numbers with the correct hw
interrupts.
Fixes: 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts")
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This driver uses the MSI domain but has no strict dependency on PCI_MSI, so we
may run into a build failure when CONFIG_GENERIC_MSI_IRQ_DOMAIN is disabled:
drivers/irqchip/irq-mvebu-odmi.c:152:15: error: variable 'odmi_msi_ops' has initializer but incomplete type
static struct msi_domain_ops odmi_msi_ops = {
^~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:155:15: error: variable 'odmi_msi_domain_info' has initializer but incomplete type
static struct msi_domain_info odmi_msi_domain_info = {
^~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:3: error: 'struct msi_domain_info' has no member named 'flags'
.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
^~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:12: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function)
.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:39: error: 'MSI_FLAG_USE_DEF_CHIP_OPS' undeclared here (not in a function); did you mean 'MSI_FLAG_USE_DEF_DOM_OPS'?
Selecting the option from this driver seems to solve this nicely, though I could
not find any other instance of this in irqchip drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- irqchip/crossbar: Some type tidying up
- irqchip/gicv3-its: Workaround for a Qualcomm erratum
- irqdomain: Compile for for systems that don't use CONFIG_IRQ_DOMAIN
-----BEGIN PGP SIGNATURE-----
iQFJBAABCAAzFiEEaVjJ8iM8Xp1syoGKqzCcdLk7HqEFAljBLCQVHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJEKswnHS5Ox6h6h8IAJKt0NHSLV4vQH51MdX1flj8uyw0
xzeosx/r7hsV/apbaFcciJuaOZNDYdVH+a1NboklpDe2g8N1eSwSITodXnsg3seO
1EyGWkZT9lWbz8/febvG8WPLLZJu0CeD9wNRT7cePTUgNZgGRR1IN6ySM/TtWixA
csIL9kgdRvChcU6hydTPceBzN5pSpZ169+BTeEL5CVTggRiq24fJlmBwM7caOu1Z
nZDsKckUQA5D/VO0CiopE6BpCZTBzB6TTC2251DEEfVxyL6/M947lOtsC4EXK4y2
6CjWM4II24ImvPmqYDNIwzK1ZimhWO0Uo8jy1LZZKVpiXXXk8zm6LKxqJbU=
=JV9b
-----END PGP SIGNATURE-----
Merge tag 'irq-fixes-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip/irqdomain updates for 4.11-rc2 from Marc Zyngier
- irqchip/crossbar: Some type tidying up
- irqchip/gicv3-its: Workaround for a Qualcomm erratum
- irqdomain: Compile for for systems that don't use CONFIG_IRQ_DOMAIN
Fixed up minor conflict in the crossbar driver.
The 'size' variable is unsigned according to the dt-bindings.
As this variable is used as integer in other places, create a new variable
that allows to fix the following sparse issue (-Wtypesign):
drivers/irqchip/irq-crossbar.c:279:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:279:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:279:52: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Cc: marc.zyngier@arm.com
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20170223094855.6546-1-fdemathieu@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes include:
* KVM PCIe/MSI passthrough support on ARM/ARM64
* Introduction of a core representation for individual hardware
iommus
* Support for IOMMU privileged mappings as supported by some
ARM IOMMUS
* 16-bit SID support for ARM-SMMUv2
* Stream table optimization for ARM-SMMUv3
* Various fixes and other small improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5b3I
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU UPDATES from Joerg Roedel:
- KVM PCIe/MSI passthrough support on ARM/ARM64
- introduction of a core representation for individual hardware iommus
- support for IOMMU privileged mappings as supported by some ARM IOMMUS
- 16-bit SID support for ARM-SMMUv2
- stream table optimization for ARM-SMMUv3
- various fixes and other small improvements
* tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (61 commits)
vfio/type1: Fix error return code in vfio_iommu_type1_attach_group()
iommu: Remove iommu_register_instance interface
iommu/exynos: Make use of iommu_device_register interface
iommu/mediatek: Make use of iommu_device_register interface
iommu/msm: Make use of iommu_device_register interface
iommu/arm-smmu: Make use of the iommu_register interface
iommu: Add iommu_device_set_fwnode() interface
iommu: Make iommu_device_link/unlink take a struct iommu_device
iommu: Add sysfs bindings for struct iommu_device
iommu: Introduce new 'struct iommu_device'
iommu: Rename struct iommu_device
iommu: Rename iommu_get_instance()
iommu: Fix static checker warning in iommu_insert_device_resv_regions
iommu: Avoid unnecessary assignment of dev->iommu_fwspec
iommu/mediatek: Remove bogus 'select' statements
iommu/dma: Remove bogus dma_supported() implementation
iommu/ipmmu-vmsa: Restrict IOMMU Domain Geometry to 32-bit address space
iommu/vt-d: Don't over-free page table directories
iommu/vt-d: Tylersburg isoch identity map check is done too late.
iommu/vt-d: Fix some macros that are incorrectly specified in intel-iommu
...
Pull irq updates from Thomas Gleixner:
"This update provides:
- Yet another two irq controller chip drivers
- A few updates and fixes for GICV3
- A resource managed function for interrupt allocation
- Fixes, updates and enhancements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/qcom: Fix error handling
genirq: Clarify logic calculating bogus irqreturn_t values
genirq/msi: Add stubs for get_cached_msi_msg/pci_write_msi_msg
genirq/devres: Use dev_name(dev) as default for devname
genirq: Fix /proc/interrupts output alignment
irqdesc: Add a resource managed version of irq_alloc_descs()
irqchip/gic-v3-its: Zero command on allocation
irqchip/gic-v3-its: Fix command buffer allocation
irqchip/mips-gic: Fix local interrupts
irqchip: Add a driver for Cortina Gemini
irqchip: DT bindings for Cortina Gemini irqchip
irqchip/gic-v3: Remove duplicate definition of GICD_TYPER_LPIS
irqchip/gic-v3-its: Rename MAPVI to MAPTI
irqchip/gic-v3-its: Drop deprecated GITS_BASER_TYPE_CPU
irqchip/gic-v3-its: Refactor command encoding
irqchip/gic-v3-its: Enable cacheable attribute Read-allocate hints
irqchip/qcom: Add IRQ combiner driver
ACPI: Add support for ResourceSource/IRQ domain mapping
ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
irq/platform-msi: Fix comment about maximal MSIs
When reusing commands from the ring buffer, it would be better
to zero them out, even if the ITS should ignore the unused
fields.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The its command buffer must be page aligned, but kzalloc() is not
guaranteed to be (though it is mostly when allocating 64k). Use
__get_free_pages() as this is used for other buffers as well.
Signed-off-by: Robert Richter <rrichter@cavium.com>
[Marc: fixed the error path]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some local interrupts are not initialised properly at the moment and
cannot be used since the domain's alloc method is never called for them.
This has been observed earlier and partially fixed in commit
e875bd66df ("irqchip/mips-gic: Fix local interrupts"), but that change
still relied on the interrupt to be requested by an external driver (eg.
drivers/clocksource/mips-gic-timer.c).
This does however not solve the issue for interrupts that are not
referenced by any driver through the device tree and results in
request_irq() calls returning -ENOSYS. It can be observed when attempting
to use perf tool to access hardware performance counters.
Fix this by explicitly calling irq_create_fwspec_mapping() for local
interrupts.
Fixes: e875bd66df ("irqchip/mips-gic: Fix local interrupts")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As a part of transitioning the Gemini platform to device tree we
create this clean, device-tree-only irqchip driver.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Back in the days when the GICv3/v4 architecture was drafted,
the command to an event to an LPI number was called MAPVI.
Later on, and to avoid confusion with the GICv4 command VMAPI,
it was renamed MAPTI. We've carried the old name for a long
time, but it gets in the way of people reading the code in
the light of the public architecture specification.
Just repaint all the references and kill the old definition.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
During the development of the GICv3/v4 architecture, it was
envisaged to have a CPU table, though the use for it was
never completely clear (the collection table serves that role
pretty well). It ended being dropped before the specification
was published, though it lived on in the driver.
In order to avoid people scratching their head too much, let's do
the same in the kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The way we encode the various ITS command fields is both tedious
and error prone. Let's introduce a helper function that performs
the encoding, and convert the existing encoders to use that
helper. It also has the advantage of expressing the encoding in
a way that matches the architecture specification.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Read-allocation hints are not enabled for both the GIC-ITS and GICR
tables. This forces the hardware to always read the table contents
from an external memory (DDR) which is slow compared to cache memory.
Most of the tables are often read by hardware. So, it's better to
enable Read-allocate hints in addition to Write-allocate hints in
order to improve the GICR_PEND, GICR_PROP, Collection, Device, and
vCPU tables lookup time.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Driver for interrupt combiners in the Top-level Control and Status
Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by
OR'ing the individual interrupt signals into a summary interrupt
signal routed to a parent interrupt controller, and provides read-
only, 32-bit registers to query the status of individual interrupts.
The status bit for IRQ n is bit (n % 32) within register (n / 32)
of the given combiner. Thus, each combiner can be described as a set
of register offsets and the number of IRQs managed.
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GICv3 ITS is MSI remapping capable. Let's advertise
this property so that VFIO passthrough can assess IRQ safety.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ICOLL controller doesn't provide any facility to configure the
wakeup sources. That's the reason why this implementation lacks
the irq_set_wake implementation. But this prevent us from properly
entering power management states like "suspend to idle".
So enable the flags IRQCHIP_SKIP_SET_WAKE and
IRQCHIP_MASK_ON_SUSPEND to let the irqchip core allows and handles
the power management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Link: https://lkml.kernel.org/r/1482863397-11400-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The below call chain generates "scheduling while atomic" backtrace and
causes system crash when Keystone 2 IRQ chip driver is used with RT-kernel:
gic_handle_irq()
|-__handle_domain_irq()
|-generic_handle_irq()
|-keystone_irq_handler()
|-regmap_read()
|-regmap_lock_spinlock()
|-rt_spin_lock()
The reason is that Keystone driver dispatches IRQ using chained IRQ handler
and accesses I/O memory through syscon->regmap(mmio) which is implemented
as fast_io regmap and uses regular spinlocks for synchronization, but
spinlocks transformed to rt_mutexes on RT.
Hence, convert Keystone 2 IRQ driver to use generic irq handler instead of
chained IRQ handler. This way it will be compatible with RT kernel where it
will be forced thread IRQ handler while in non-RT kernel it still will be
executed in HW IRQ context.
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Link: https://lkml.kernel.org/r/20161208233310.10329-1-grygorii.strashko@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- Uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- Support for systems without FP/SIMD (IOW, kernel avoids touching these
registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- Handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- Use of the page table contiguous hint for kernel mappings
- Hugetlb fixes for sizes involving the contiguous hint
- Remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- Boot-time checks for writable+executable kernel mappings
- Simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Uk9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- struct thread_info moved off-stack (also touching
include/linux/thread_info.h and include/linux/restart_block.h)
- cpus_have_cap() reworked to avoid __builtin_constant_p() for static
key use (also touching drivers/irqchip/irq-gic-v3.c)
- uprobes support (currently only for native 64-bit tasks)
- Emulation of kernel Privileged Access Never (PAN) using TTBR0_EL1
switching to a reserved page table
- CPU capacity information passing via DT or sysfs (used by the
scheduler)
- support for systems without FP/SIMD (IOW, kernel avoids touching
these registers; there is no soft-float ABI, nor kernel emulation for
AArch64 FP/SIMD)
- handling of hardware watchpoint with unaligned addresses, varied
lengths and offsets from base
- use of the page table contiguous hint for kernel mappings
- hugetlb fixes for sizes involving the contiguous hint
- remove unnecessary I-cache invalidation in flush_cache_range()
- CNTHCTL_EL2 access fix for CPUs with VHE support (ARMv8.1)
- boot-time checks for writable+executable kernel mappings
- simplify asm/opcodes.h and avoid including the 32-bit ARM counterpart
and make the arm64 kernel headers self-consistent (Xen headers patch
merged separately)
- Workaround for broken .inst support in certain binutils versions
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (60 commits)
arm64: Disable PAN on uaccess_enable()
arm64: Work around broken .inst when defective gas is detected
arm64: Add detection code for broken .inst support in binutils
arm64: Remove reference to asm/opcodes.h
arm64: Get rid of asm/opcodes.h
arm64: smp: Prevent raw_smp_processor_id() recursion
arm64: head.S: Fix CNTHCTL_EL2 access on VHE system
arm64: Remove I-cache invalidation from flush_cache_range()
arm64: Enable HIBERNATION in defconfig
arm64: Enable CONFIG_ARM64_SW_TTBR0_PAN
arm64: xen: Enable user access before a privcmd hvc call
arm64: Handle faults caused by inadvertent user access with PAN enabled
arm64: Disable TTBR0_EL1 during normal kernel execution
arm64: Introduce uaccess_{disable,enable} functionality based on TTBR0_EL1
arm64: Factor out TTBR0_EL1 post-update workaround into a specific asm macro
arm64: Factor out PAN enabling/disabling into separate uaccess_* macros
arm64: Update the synchronous external abort fault description
selftests: arm64: add test for unaligned/inexact watchpoint handling
arm64: Allow hw watchpoint of length 3,5,6 and 7
arm64: hw_breakpoint: Handle inexact watchpoint addresses
...
The Xilinx interrupt controller driver is now available in drivers/irqchip.
Switch to using that driver.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The powerpc dts file does not have the xlnx,kind-of-intr property.
Instead of erroring out, give a warning instead. And attempt to
continue to probe the interrupt controller while assuming
kind-of-intr is 0x0 as a fall back.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The MIPS based xilfpga platform has the following IRQ structure
Peripherals --> xilinx_intcontroller -> mips_cpu_int controller
Add support for the driver to chain the irq handler
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that the driver is generic and used by multiple archs,
get_irq is too generic.
Rename get_irq to xintc_get_irq to avoid any conflicts
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a global structure to house various variables.
And cleanup read/write handling by using jump label api.
Tested-by; Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Remove __func__ and prefix irq-xilinx in various debug prints
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Xilinx AXI Interrupt Controller IP block is used by the MIPS
based xilfpga platform and a few PowerPC based platforms.
Move the interrupt controller code out of arch/microblaze so that
it can be used by everyone
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
readq and writeq type of assessors are not supported in AArch32, so we
need to specialise them and glue later with series of 32-bit accesses
on AArch32 side.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It'd be better to switch to CMA... but before that done redirect
flush_dcache operation, so 32-bit implementation could be wired
latter.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
GITS_BASER<n>'s Entry Size is much smaller than 64-bit, but when it
used as a divider it forces compiler to generate __aeabi_uldivmod if
build in 32-bit mode. So, casting it to int (like it is done in other
places) where used as a divider would give a hint to compiler that
32-bit division can be used.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make sure that constants which are supposed to be applied on 64-bit
data is actually unsigned long long, so they won't be truncated when
used in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The hypervisor may not have full access to the kernel data structures
and hence cannot safely use cpus_have_cap() helper for checking the
system capability. Add a safe helper for hypervisors to check a constant
system capability, which *doesn't* fall back to checking the bitmap
maintained by the kernel. With this, make the cpus_have_cap() only
check the bitmask and force constant cap checks to use the new API
for quicker checks.
Cc: Robert Ritcher <rritcher@cavium.com>
Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DL0w
-----END PGP SIGNATURE-----
Merge tag 'gic-fixes-for-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull GIC updates from Marc Zyngier:
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
Core drivers for J-Core SoCs will be selected implicitly via
CONFIG_SH_JCORE_SOC instead. Based on a corresponding change to the
clocksource/timer driver requested by Daniel Lezcano.
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/883a3d17084003e3cf21bab73ec12828fe4ff6c6.1476899495.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no need to have the 'struct irq_domain *nps400_root_domain'
variable static since new value is always assigned before use.
Fixes: 44df427c89 ("irqchip: add nps Internal and external irqchips")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1476714417-12095-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GICv3 architecture specification mentions that a 64bit
register can be accessed using two 32bit accesses. What it
doesn't mention is that this is only guaranteed on a system
that implements AArch32, and a pure AArch64 system is allowed
not to support this. This causes issues with the GICR_TYPER
and GITS_TYPER registers, which are both RO 64bit registers.
In order to solve this, this patch switches the TYPER accesses
to the gic_read_typer macro already used in other parts of the
driver. This makes sure that we always use a 64bit access on
64bit systems, and two 32bit accesses on 32bit system.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
The timeout loop terminates when the loop count is zero, but the decrement
of the count variable is post check. So count is -1 when we check for the
timeout and therefor the error message is supressed.
Change it to predecrement, so the error message is emitted.
[ tglx: Massaged changelog ]
Fixes: a2c2251012 ("irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20161014072534.GA15168@mwanda
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The J-Core AIC does not have separate interrupt numbers reserved for
cpu-local vs global interrupts. Instead, the driver requesting the irq
is expected to know whether its device uses per-cpu interrupts or not.
Previously it was assumed that handle_simple_irq could work for both
cases, but it intentionally drops interrupts for an irq number that
already has a handler running. This resulted in the timer interrupt
for one cpu being lost when multiple cpus' timers were set for
approximately the same expiration time, leading to stalls. In theory
the same could also happen with IPIs.
To solve the problem, instead of registering handle_simple_irq as the
handler, register a wrapper function which checks whether the irq to
be handled was requested as per-cpu or not, and passes it to
handle_simple_irq or handle_percpu_irq accordingly.
Fixes: 981b58f66c ("irqchip/jcore-aic: Add J-Core AIC driver")
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/f18cec30bc17e3f52e478dd9f6714bfab02f227f.1476390724.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including:
* Support for interrupt virtualization in the AMD IOMMU driver.
These patches were shared with the KVM tree and are already
merged through that tree.
* Generic DT-binding support for the ARM-SMMU driver. With this
the driver now makes use of the generic DMA-API code. This
also required some changes outside of the IOMMU code, but
these are acked by the respective maintainers.
* More cleanups and fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJX/PmUAAoJECvwRC2XARrjyloP/1hymxXC2yXZ4EIBTHSO5X+c
jSJaGTIbQAdQDpllscSNJ0Au43L3vGtJcHo4JqwEERNlwLsU82LH7QJhq+q1La/b
5cPaY5gI3E++qxQt8umuZJAIUQthFYrfGoS5lJc5t5r/d8iVsLWbW4VkR19/1o7A
4/Uz7ETmi9VVy8Hkvumx+PQ0VHJet381KB7ud9LU5Spim0En2AAGwZXLMkmxXd2W
uDQ+O1rlDVc2/ka3+GmfZEml5EASWRqS/MTNoU/ZbQGYWKCWygXbuiqt6gLudWjx
dCR1Knh68b0gN6k/QAj8XY/1gkfmZ3YkfS0AHIMLYTFRT51BuxOrkXrBdkYnWEBv
UirmaiV87SlR1j83yb3ZmjpBPvd2sGWYFDqY1P0riLutjGUS6zycWWs13olvbfbz
SFrH7PT7JPQGYprI1oVn4ihszjN1NZ4+Gj7QBhyFW6FtvqTzmaFVsMOlDIeg1FwR
k8cOzov4NG33Bp4IpsHK8e0/qV6K3oJOiOQgCyQp9kPKK+UWv9v9+HaEA7npJuRV
c+lTE6j3G4LjEoVybkqm8TiPKxTMVNjUjgA3kwB2yNkCQT7hTCNYIAFrtfCYjYdo
B1dnFE7feVqtoimnu2qvkVs59hWlF7Hc3RRHoBxMmO8DLwl9n2OcmoQIeCTsviss
i9aNwC9bzBs+Hd3X/psB
=1hFE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- support for interrupt virtualization in the AMD IOMMU driver. These
patches were shared with the KVM tree and are already merged through
that tree.
- generic DT-binding support for the ARM-SMMU driver. With this the
driver now makes use of the generic DMA-API code. This also required
some changes outside of the IOMMU code, but these are acked by the
respective maintainers.
- more cleanups and fixes all over the place.
* tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (40 commits)
iommu/amd: No need to wait iommu completion if no dte irq entry change
iommu/amd: Free domain id when free a domain of struct dma_ops_domain
iommu/amd: Use standard bitmap operation to set bitmap
iommu/amd: Clean up the cmpxchg64 invocation
iommu/io-pgtable-arm: Check for v7s-incapable systems
iommu/dma: Avoid PCI host bridge windows
iommu/dma: Add support for mapping MSIs
iommu/arm-smmu: Set domain geometry
iommu/arm-smmu: Wire up generic configuration support
Docs: dt: document ARM SMMU generic binding usage
iommu/arm-smmu: Convert to iommu_fwspec
iommu/arm-smmu: Intelligent SMR allocation
iommu/arm-smmu: Add a stream map entry iterator
iommu/arm-smmu: Streamline SMMU data lookups
iommu/arm-smmu: Refactor mmu-masters handling
iommu/arm-smmu: Keep track of S2CR state
iommu/arm-smmu: Consolidate stream map entry state
iommu/arm-smmu: Handle stream IDs more dynamically
iommu/arm-smmu: Set PRIVCFG in stage 1 STEs
iommu/arm-smmu: Support non-PCI devices with SMMUv3
...
Pull irq fixes from Thomas Gleixner:
"Two small kerneldoc fixes from Julia Lawall"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/metag-ext: Improve function-level documentation
irqchip/vic: Improve function-level documentation
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
The i8259A_irq_pending function is unused. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The default i8259 polling function (i8259_irq) is nicely generic but is
fairly costly. Platforms often provide an alternative means of polling
for an i8259 interrupt, and when using the i8259 without device tree
have typically just chained its parent interrupt to their own handler
function. In order to allow for platform-specific polling functions to
be used in cases where the driver is probed via device tree, provide an
i8259_set_poll function that accepts a pointer to an alternative poll
function that will override the default.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14270/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mapping the parent IRQ will use a virq number which may conflict with
the hardcoded I8259A_IRQ_BASE..I8259A_IRQ_BASE+15 range that the i8259
driver expects to be free. If this occurs then we'll hit errors when
adding the i8259 IRQ domain, since one of its virq numbers will already
be in use.
Avoid this by adding the i8259 domain before mapping the parent IRQ,
such that the i8259 virq numbers become used before the parent interrupt
controller gets a chance to use any of them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14269/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The STM32 external interrupt controller consists of edge detectors that
generate interrupts requests or wake-up events.
Each line can be independently configured as interrupt or wake-up source,
and triggers either on rising, falling or both edges. Each line can also
be masked independently.
Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: arnd@arndb.de
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: bruherrera@gmail.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: lee.jones@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1474387259-18926-3-git-send-email-alexandre.torgue@st.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The MIPS GIC driver has previously iterated over bits set in a bitmap
representing pending local IRQs by calling find_first_bit, clearing that
bit then calling find_first_bit again until all bits are clear. If
multiple interrupts are pending then this is wasteful, as find_first_bit
will have to loop over the whole bitmap from the start. Use the
for_each_set_bit macro which performs exactly what we need here instead.
It will use find_next_bit and thus only scan over the relevant part of
the bitmap, and it makes the intent of the code clearer.
This makes the same change for local interrupts that commit cae750bae4
("irqchip: mips-gic: Use for_each_set_bit to iterate over IRQs") made
for shared interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20160913165427.31686-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the device hierarchy domain was added by commit c98c1822ee
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: stable@vger.kernel.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_raise_softirq() walks the list of cpus using for_each_cpu(), it calls
gic_compute_target_list() which advances the iterator by the number of
CPUs in the cluster.
If gic_compute_target_list() reaches the last CPU it leaves the iterator
pointing at the last CPU. This means the next time round the for_each_cpu()
loop cpumask_next() will be called with an invalid CPU.
This triggers a warning when built with CONFIG_DEBUG_PER_CPU_MAPS:
[ 3.077738] GICv3: CPU1: found redistributor 1 region 0:0x000000002f120000
[ 3.077943] CPU1: Booted secondary processor [410fd0f0]
[ 3.078542] ------------[ cut here ]------------
[ 3.078746] WARNING: CPU: 1 PID: 0 at ../include/linux/cpumask.h:121 gic_raise_softirq+0x12c/0x170
[ 3.078812] Modules linked in:
[ 3.078869]
[ 3.078930] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc5+ #5188
[ 3.078994] Hardware name: Foundation-v8A (DT)
[ 3.079059] task: ffff80087a1a0080 task.stack: ffff80087a19c000
[ 3.079145] PC is at gic_raise_softirq+0x12c/0x170
[ 3.079226] LR is at gic_raise_softirq+0xa4/0x170
[ 3.079296] pc : [<ffff0000083ead24>] lr : [<ffff0000083eac9c>] pstate: 200001c9
[ 3.081139] Call trace:
[ 3.081202] Exception stack(0xffff80087a19fbe0 to 0xffff80087a19fd10)
[ 3.082269] [<ffff0000083ead24>] gic_raise_softirq+0x12c/0x170
[ 3.082354] [<ffff00000808e614>] smp_send_reschedule+0x34/0x40
[ 3.082433] [<ffff0000080e80a0>] resched_curr+0x50/0x88
[ 3.082512] [<ffff0000080e89d0>] check_preempt_curr+0x60/0xd0
[ 3.082593] [<ffff0000080e8a60>] ttwu_do_wakeup+0x20/0xe8
[ 3.082672] [<ffff0000080e8bb8>] ttwu_do_activate+0x90/0xc0
[ 3.082753] [<ffff0000080ea9a4>] try_to_wake_up+0x224/0x370
[ 3.082836] [<ffff0000080eabc8>] default_wake_function+0x10/0x18
[ 3.082920] [<ffff000008103134>] __wake_up_common+0x5c/0xa0
[ 3.083003] [<ffff0000081031f4>] __wake_up_locked+0x14/0x20
[ 3.083086] [<ffff000008103f80>] complete+0x40/0x60
[ 3.083168] [<ffff00000808df7c>] secondary_start_kernel+0x15c/0x1d0
[ 3.083240] [<00000000808911a4>] 0x808911a4
[ 3.113401] Detected PIPT I-cache on CPU2
Avoid updating the iterator if the next call to cpumask_next() would
cause the for_each_cpu() loop to exit.
There is no change to gic_raise_softirq()'s behaviour, (cpumask_next()s
eventual call to _find_next_bit() will return early as start >= nbits),
this patch just silences the warning.
Fixes: 021f653791 ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1474306155-3303-1-git-send-email-james.morse@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When an MSI doorbell is located downstream of an IOMMU, attaching
devices to a DMA ops domain and switching on translation leads to a rude
shock when their attempt to write to the physical address returned by
the irqchip driver faults (or worse, writes into some already-mapped
buffer) and no interrupt is forthcoming.
Address this by adding a hook for relevant irqchip drivers to call from
their compose_msi_msg() callback, to swizzle the physical address with
an appropriatly-mapped IOVA for any device attached to one of our DMA
ops domains.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
aic5_irq_domain_xlate() and aic_irq_domain_xlate() take the generic chip
lock without disabling interrupts, which can lead to a deadlock if an
interrupt occurs while the lock is held in one of these functions.
Replace irq_gc_{lock,unlock}() calls by
irq_gc_{lock_irqsave,unlock_irqrestore}() ones to prevent this bug from
happening.
Fixes: b1479ebb77 ("irqchip: atmel-aic: Add atmel AIC/AIC5 drivers")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Link: http://lkml.kernel.org/r/1473775109-4192-2-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Let ACPI build ITS PCI MSI domain. ACPI code is responsible for retrieving
inner domain token and passing it on to its_pci_msi_init_one generic
init call.
IORT maintains list of registered domain tokens and allows to find
corresponding domain based on MADT ITS subtable ID info.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Firmware agnostic code lands in common functions which do necessary
domain initialization based on unique domain handler. DT specific
code goes to DT specific init call.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ITS is prepared for being initialized different than DT,
therefore we can initialize it in ACPI way. We collect register base
address from MADT table and pass mandatory info to firmware-agnostic
ITS init call.
Use here IORT lib to register ITS domain which then can be found and
used on to build another PCI MSI domain in hierarchical stack domain.
NOTE: Waiting for proper ITS and NUMA node relation description in IORT
table, we pass around NUMA_NO_NODE to the its_probe_one init call.
This means that Cavium ThunderX erratum 23144 (pass1.1 only)
is not supported for ACPI boot method yet.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to add ACPI support we need to isolate ACPI&DT common code and
move DT logic to corresponding functions. To achieve this we are using
firmware agnostic handle which can be unpacked to either DT or ACPI node.
No functional changes other than a very minor one:
1. Terminate its_init call with -ENODEV for non-DT case which allows
to remove hack from its-gic-v3.c.
2. Fix ITS base register address type (from 'unsigned long' to 'phys_addr_t'),
as a bonus we get nice string formatting.
3. Since there is only one of ITS parent domain convert it to static global
variable and drop the parameter from its_probe_one. Users can refer to it
in more convenient way then.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no point to initialize ITS without having msi-controller
property in corresponding DT node. However, its_probe is checking
msi-controller presence at the end, so we can save our time and do that
check prior to its_probe call. Also, for the code clarity purpose,
we put domain initialization to separate function.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We get 1 warning when building kernel with W=1:
drivers/irqchip/irq-gic.c:917:13: warning: no previous prototype for 'gic_init_physaddr' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 498b5fdd40 ("PM / clk: Add support for adding a specific clock
from device-tree") add a new helper function for adding a clock from
device-tree to a device. Update the GIC-PM driver to use this new
function to simplify the driver.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, when running on FVP, CPU 0 boots up with its BPR changed from
the reset value. This renders it impossible to (preemptively) prioritize
interrupts on CPU 0.
This is harmless on normal systems since Linux typically does not
support preemptive interrupts. It does however cause problems in
systems with additional changes (such as patches for NMI simulation).
Many thanks to Andrew Thoelke for suggesting the BPR as having the
potential to harm preemption.
Suggested-by: Andrew Thoelke <andrew.thoelke@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The BL switcher code manipulates the logical/physical CPU mapping,
forcing a lock to be taken on the IPI path. With an IPI heavy load,
this single lock becomes contended.
But when CONFIG_BL_SWITCHER is not enabled, there is no reason
to take this lock at all since the CPU mapping is immutable.
This patch allows the lock to be entierely removed when BL_SWITCHER
is not enabled (which is the case in most configurations), leading
to a small improvement of "perf bench sched pipe" (measured on
an 8 core AMD Seattle system):
Before: 101370 ops/sec
After: 103680 ops/sec
Take this opportunity to remove a useless lock being taken when
handling an interrupt on a secondary GIC.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
around the Kconfig options and leaves the mach-realview
directory nice and tidy, with all boards migrated over to
Device Tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HWSr
-----END PGP SIGNATURE-----
Merge tag 'realview-broomstick-sweep' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
Merge "delete the RealView boardfiles" from Linus Walleij:
This deletes the realview boardfiles, consolidates a bit
around the Kconfig options and leaves the mach-realview
directory nice and tidy, with all boards migrated over to
Device Tree.
* tag 'realview-broomstick-sweep' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
The MIPS GIC driver has previously iterated over bits set in a bitmap
representing pending IRQs by calling find_first_bit, clearing that bit
then calling find_first_bit again until all bits are clear. If multiple
interrupts are pending then this is wasteful, as find_first_bit will
have to loop over the whole bitmap from the start. Use the
for_each_set_bit macro which performs exactly what we need here instead.
It will use find_next_bit and thus only scan over the relevant part of
the bitmap, and it makes the intent of the code more clear.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Link: https://lkml.kernel.org/r/20160819171119.28121-1-paul.burton@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fixes the following sparse warning:
drivers/irqchip/irq-jcore-aic.c:47:12: warning:
symbol 'aic_irq_of_init' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Link: https://lkml.kernel.org/r/1471706788-27587-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 7K/8K integrates a secondary interrupt controller
very originally named "PIC". It is connected to the main GIC via a
PPI. Amongst other things, this PIC is used for the ARM PMU.
This commit adds a simple irqchip driver for this interrupt
controller. Since this interrupt controller is not needed early at boot
time, we make the driver a proper platform driver rather than use the
IRQCHIP_DECLARE() mechanism.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1470408921-447-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If an IRQ is setup using __setup_irq(), which is used by the
request_irq() family of functions, and we are using an SMP kernel then
the affinity of the IRQ will be set via setup_affinity() immediately
after the IRQ is enabled. This call to gic_set_affinity() will lead to
the interrupt being mapped to a VPE. However there are other ways to use
IRQs which don't cause affinity to be set, for example if it is used to
chain to another IRQ controller with irq_set_chained_handler_and_data().
The irq_set_chained_handler_and_data() code path will enable the IRQ,
but will not trigger a call to gic_set_affinity() and in this case
nothing will map the interrupt to a VPE, meaning that the interrupt is
never received.
Fix this by implementing the activate operation for the GIC device IRQ
domain, using gic_shared_irq_domain_map() to map the interrupt to the
correct pin of cpu 0.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_shared_irq_domain_map() is called from gic_irq_domain_alloc() where
the wrong chip has been set, and is then overwritten. Tidy this up by
setting the correct chip the first time, and setting the
handle_level_irq handler from gic_irq_domain_alloc() too.
gic_shared_irq_domain_map() is also called from gic_irq_domain_map(),
which now calls irq_set_chip_and_handler() to retain its previous
behaviour.
This patch prepares for a follow-on which will call
gic_shared_irq_domain_map() from a callback where the lock on the struct
irq_desc is held, which without this change would cause the call to
irq_set_chip_and_handler() to lead to a deadlock.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When starting a kexec/kdump kernel, the GIC ITS will already have been
enabled. According to the ARM Generic Interrupt Controller
Architecture Specification (GIC architecture Version 3.0 and version
4.0), writing to GITS_BASER<n> or GITS_CBASER is "UNPREDICTABLE" when
the ITS is enabled. On Cavium Thunder systems, this prevents the ITS
from being initializing in the kexec/kdump kernel, resulting in
failure to register/enable interrupts for all devices.
The fix is to disable the ITS if it is not already in the disabled
state. This allows the ITS to be properly initialized and then
re-enabled in the kexec/kdump kernel.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing
to GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.
When commit 3708d52fc6 ("irqchip: gic-v3: Implement CPU PM notifier")
was introduced there were no firmware implementations(in particular PSCI)
handling this.
Linux kernel may not be aware of the CPU power state details and might
fail to identify the power states that require quiescing the CPU
interface. Even if it can be aware of those details, it can't determine
which CPU power state have been triggered at the platform level and how
the power control is implemented.
This patch make disabling redistributor and group1 non-secure interrupts
in the power down path and re-enabling of redistributor in the power-up
path conditional. It will be handled in the kernel if and only if the
non-secure accesses are permitted to access and modify control registers.
It is left to the platform implementation otherwise.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On systems where a single CPU is present, the GIC may not support
having SGIs delivered to a target list. In that case, we use the
self-SGI mechanism to allow the interrupt to be delivered locally.
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This reduces the Kconfig for the RealView by assuming we are
always booting from the device tree, and removing all the uses
of CONFIG_REALVIEW_DT and replacing with CONFIG_ARCH_REALVIEW.
Further:
- Drop REALVIEW_HIGH_PHYS_OFFSET: we don't use this with device
tree.
- Drop the REALVIEW_EB_ARM11MP_REVB option: we now handle this
by simply using another device tree.
- Drop the PB1176 secure flash option: this is defined in the
PB1176 device tree but marked as "disabled", so users who
want to use it can simply enable it in the device tree and
go hacking around.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two versions of the J-Core interrupt controller in use, aic1
which generates interrupts with programmable priorities, but only
supports 8 irq lines and maps them to cpu traps in the range 17 to 24,
and aic2 which uses traps in the range 64-127 and supports up to 128
irqs, with priorities dependent on the interrupt number. The Linux
driver does not make use of priorities anyway.
For simplicity, there is no aic1-specific logic in the driver beyond
setting the priority register, which is necessary for interrupts to
work at all. Eventually aic1 will likely be phased out, but it's
currently in use in deployments and all released bitstream binaries.
Signed-off-by: Rich Felker <dalias@libc.org>
Link: https://lkml.kernel.org/r/c3b89ef74aaa6477575dbe2d410eb1d182503243.147018b6529.git.dalias@libc.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
Pull irq updates from Thomas Gleixner:
"The irq department delivers:
- new core infrastructure to allow better management of multi-queue
devices (interrupt spreading, node aware descriptor allocation ...)
- a new interrupt flow handler to support the new fangled Intel VMD
devices.
- yet another new interrupt controller driver.
- a series of fixes which addresses sparse warnings, missing
includes, missing static declarations etc from Ben Dooks.
- a fix for the error handling in the hierarchical domain allocation
code.
- the usual pile of small updates to core and driver code"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
genirq: Fix missing irq allocation affinity hint
irqdomain: Fix irq_domain_alloc_irqs_recursive() error handling
irq/Documentation: Correct result of echnoing 5 to smp_affinity
MAINTAINERS: Remove Jiang Liu from irq domains
genirq/msi: Fix broken debug output
genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors
genirq/msi: Make use of affinity aware allocations
genirq: Use affinity hint in irqdesc allocation
genirq: Add affinity hint to irq allocation
genirq: Introduce IRQD_AFFINITY_MANAGED flag
genirq/msi: Remove unused MSI_FLAG_IDENTITY_MAP
irqchip/s3c24xx: Fixup IO accessors for big endian
irqchip/exynos-combiner: Fix usage of __raw IO
irqdomain: Fix disposal of mappings for interrupt hierarchies
irqchip/aspeed-vic: Add irq controller for Aspeed
doc/devicetree: Add Aspeed VIC bindings
x86/PCI/VMD: Use untracked irq handler
genirq: Add untracked irq handler
irqchip/mips-gic: Populate irq_domain names
irqchip/gicv3-its: Implement two-level(indirect) device table support
...
When building with CONFIG_SMP disabled, we get some new harmless warnings:
drivers/irqchip/irq-armada-370-xp.c:356:12: error: 'mpic_cascaded_starting_cpu' defined but not used [-Werror=unused-function]
static int mpic_cascaded_starting_cpu(unsigned int cpu)
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-armada-370-xp.c:349:12: error: 'armada_xp_mpic_starting_cpu' defined but not used [-Werror=unused-function]
static int armada_xp_mpic_starting_cpu(unsigned int cpu)
This moves the unused functions into the #ifdef, as they previously were.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Cochran <rcochran@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: cb5ff2d245 ("irqchip/armada-370-xp: Convert to hotplug state machine")
Link: http://lkml.kernel.org/r/20160718160335.3134412-1-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.416260485@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.330661455@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.244546182@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.163186301@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
More or less straightforward, although this driver sports some very
interesting SMP setup code. Regarding the callback ordering, this
deleted comment is interesting:
... the GIC needs to be up before the ARM generic timers.
That comment is half baken as the same requirement is true for perf.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.069777215@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When mapping an interrupt to a VP(E) we must use the identifier for the
VP that the hardware expects, and this does not always match up with the
Linux CPU number. Commit d46812bb0b ("irqchip: mips-gic: Use HW IDs
for VPE_OTHER_ADDR") corrected this for the cases that existed at the
time it was written, but commit 2af70a9620 ("irqchip/mips-gic: Add a
IPI hierarchy domain") added another case before the former patch was
merged. This leads to incorrectly using Linux CPU numbers when mapping
interrupts to VPs, which breaks on certain systems such as those with
multi-core I6400 CPUs. Fix by adding the appropriate call to
mips_cm_vp_id() to retrieve the expected VP identifier.
Fixes: d46812bb0b ("irqchip: mips-gic: Use HW IDs for VPE_OTHER_ADDR")
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160705132600.27730-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of using the __raw accessors, use the _relaxed versions
to deal with any issues due to endian-ness of the CPU.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[jac: reformat subject line, fix commit message typo]
Link: https://lkml.kernel.org/r/1466504432-24187-10-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fix the use of __raw IO accessors when the readl/writel_relaxed
are better. This should fix issues if the kernel is running as
big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[jac: reformat subject line, fix commit message typo]
Link: https://lkml.kernel.org/r/1466504432-24187-9-git-send-email-ben.dooks@codethink.co.uk
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The PCI_MSI symbol is used inconsistently throughout the tree, with some
drivers using 'select' and others using 'depends on', or using conditional
selects. This keeps causing problems; the latest one is a result of
ARCH_ALPINE using a 'select' statement to enable its platform-specific MSI
driver without enabling MSI:
warning: (ARCH_ALPINE) selects ALPINE_MSI which has unmet direct dependencies (PCI && PCI_MSI)
drivers/irqchip/irq-alpine-msi.c:104:15: error: variable 'alpine_msix_domain_info' has initializer but incomplete type
static struct msi_domain_info alpine_msix_domain_info = {
^~~~~~~~~~~~~~~
drivers/irqchip/irq-alpine-msi.c:105:2: error: unknown field 'flags' specified in initializer
.flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
^
drivers/irqchip/irq-alpine-msi.c:105:11: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function)
.flags = MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS |
^~~~~~~~~~~~~~~~~~~~~~~~
There is little reason to enable PCI support for a platform that uses MSI
but then leave MSI disabled at compile time.
Select PCI_MSI from irqchips that implement MSI, and make PCI host bridges
that use MSI on ARM depend on PCI_MSI_IRQ_DOMAIN.
For all three architectures that support PCI_MSI_IRQ_DOMAIN (ARM, ARM64,
X86), enable it by default whenever MSI is enabled.
[bhelgaas: changelog, omit crypto config change]
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier