The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_MC9S08DZ60
drivers/gpio/Kconfig: bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Wu Guoxing <b39297@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig for this driver is currently:
config GPIO_MB86S7X
bool "GPIO support for Fujitsu MB86S7x Platforms"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config GPIO_BCM_KONA
bool "Broadcom Kona GPIO"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Ray Jui <rjui@broadcom.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs)
which is configured through SuperIO register 0xd2 (output enable) and
0xd3 (simple I/O). This is also the reason why io_size is larger than
on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th
GPIO block.
I am also not sure about not configuring the Simple I/O registers as the
hardware I have only uses GPIO block 8. Reading back the values of
0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all
have 0xff set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt for the corresponding pin is configured to trigger when the
pin state changes compared to a preconfigured state (Bit set in INTCON).
This state is set by setting/clearing the bit in DEFVAL.
In the interrupt handler we need also to check if the bit in INTCON is set
for level triggered interrupts.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The chip is also an 8 bit shift register which works out of the box as a GPO
expander with this patch
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code calls irq_domain_alloc_irqs_parent() in .alloc,
so it should call irq_domain_free_irqs_parent() accordingly in .free.
Fix it by switching to use irq_domain_free_irqs_common() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_resource() can return NULL, thus add NULL test to prevent NULL
pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code uses a uninitialized spin lock.
bgpio_init() already initialized a spin lock, so let's switch to use
&gc->bgpio_lock instead and remove the lock from struct men_z127_gpio.
Fixes: f436bc2726 "gpio: add driver for MEN 16Z127 GPIO controller"
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new ACPI HID, AMDIF030, in the pt_gpio_acpi_match.
Signed-off-by: YD Tseng<Yd_Tseng@asmedia.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use gpio-generic to simplify this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: YD Tseng <Yd_Tseng@asmedia.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using the GPIOLIB_IRQCHIP the gpiolib provides a
straight-forward implementation of request/release resources,
rely on that instead.
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the mcp23s08 driver to use the gpiolib irqchip
helpers.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to set multiple outputs using a single SPI transfer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to set multiple outputs using a single register write.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set it once is enough, so remove the second platform_set_drvdata() call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
The mcp23s18 is configurable on clearing the interrupt on either reading
INTCAP or GPIO. Since driver reads INTCAP in IRQ and not the GPIO reg need
to set control byte for this mode.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pca953x_gpio_set_multiple() divides by 4 to convert from longs to bytes,
which assumes a 32-bit platform, and is not correct on 64-bit platforms.
Use "sizeof(...)" instead to fix this.
Cc: stable@vger.kernel.org
Fixes: b4818afeac ("gpio: pca953x: Add set_multiple to allow multiple bits to be set in one write.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The standby GPIO controller can be used as a interrupt controller.
Select GPIOLIB_IRQCHIP when compiling this driver. Otherwise we get
a compilation error:
drivers/gpio/gpio-xgene-sb.c: In function 'xgene_gpio_sb_probe':
drivers/gpio/gpio-xgene-sb.c:312:10: error: 'struct gpio_chip'
has no member named 'irqdomain'
priv->gc.irqdomain = priv->irq_domain;
^
scripts/Makefile.build:295: recipe for target
'drivers/gpio/gpio-xgene-sb.o' failed
make[2]: *** [drivers/gpio/gpio-xgene-sb.o] Error 1
Fixes: 1013fc41 "gpio: xgene: Enable X-Gene standby GPIO as interrupt controller"
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the TPS65086 PMIC GPOs.
TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I screwed up while merging the immutable branch for TPS65912,
so fixing it unbroken again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO chip structure already has "parent" field which is used for the
same purpose as "dev" field in gpio_bank structure - store pointer on
GPIO device.
Hence, drop duplicated "dev" field from gpio_bank structure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.
gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;
Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.
Fixes: commit 42178e2a1e ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the mcp23s18 which is very similar to
the mcp23s17. A couple of control bits are not the same.
Notable IOCON_HAEN (s17 only) & IOCON_INTCC. Which can be ignored.
Patch changes the following:
- Add mcp23s18 types.
- Always set mirror bit if the dts defines mcp23s18. regardless of type.
Mirror bit is ignored on 8 bit devices anyway.
- In mcp23s08_probe use chip.ngpio instead of logic based on type
to determine number of gpio lins to increment by. This is set
appropiately by the call to mcp23s08_probe_one.
- Add mcp23s18 to device tree documentation.
- Remove statement that irqs don't work for spi. They do.
Tested with mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.
Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The implementation of lp3943_gpio_request/lp3943_gpio_free test pin_used
for tracing the pin usage. However, gpiolib already checks FLAG_REQUESTED
flag for the same purpose. So remove the redundant implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace calls to devm_request_mem_region and devm_ioremap with a
direct call to devm_ioremap_resource instead and modify error
handling.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more
clear.
A simplified version of the Coccinelle semantic patch that is used to
make this change is as follows:
//<smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size,e1,e;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\)))
{
- ...
- return ...;
-}
... when != res->start = e1
e =
-devm_ioremap(dev,res->start,size);
+devm_ioremap_resource(dev,res);
if
-(e == NULL)
+(IS_ERR(e))
{
...
-return ...;
+return PTR_ERR(e);
}
//</smpl>
Further, updated error handling by hand as devm_ioremap_resource
gives appropriate error messages, so remove unnecessary error
messages.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS-4800 is an i.MX515 board. Its GPIO driver should only be compiled
for this CPU or for test builds.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original code of gpiodev_add_to_list is not very clear which
lead to bugs or compiling warning, reference the following patches:
Bugs:
1. Commit ef7c755303 ("gpiolib: improve overlap check of range of
gpio").
2. Commit 96098df125 ("gpiolib: fix chip order in gpio list")
Warning:
1. Commit e28ecca6ea ("gpio: fix warning about iterator").
of gpio").
There is a off-list discussion about how to improve it consequently.
This commit try to follow this by rewriting the whole functions.
Tested pass with my gpio mockup driver and test scripts[1].
[1] http://www.spinics.net/lists/linux-gpio/msg09598.html
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These fields are initialized by bgpio_init() with exactly the same settings
so remove the redundant code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I named the field representing the current user of GPIO line as
"label" but this is too vague and ambiguous. Before anyone gets
confused, rename it to "consumer" and indicate clearly in the
documentation that this is a string set by the user of the line.
Also clean up leftovers in the documentation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We started to assign the gpio_device as parent for the sysfs
but this changes the expected layout of sysfs. Restore the
previous behaviour.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver has .can_sleep flag set.
So the pisosr_gpio_get() can be called from contexts that can sleep.
Thus use the cansleep() variant in pisosr_gpio_refresh().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ret variable can contain error values and is compared with zero.
Its type must be signed.
The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both chip->base and chip->label are correctly set by bgpio_init().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use list_for_each_entry to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the code checking valid gpio count to cover both DT and non-DT cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ret variable can contain error values and is compared with zero.
Its type must be signed.
The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both chip->base and chip->label are correctly set by bgpio_init().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use list_for_each_entry to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the code checking valid gpio count to cover both DT and non-DT cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R-Car GPIO driver handles Runtime PM for requested GPIOs only.
When using a GPIO purely as an interrupt source, no Runtime PM handling
is done, and the GPIO module's clock may not be enabled.
To fix this:
- Add .irq_request_resources() and .irq_release_resources() callbacks
to handle Runtime PM when an interrupt is requested,
- Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM
when e.g. disabling/enabling an interrupt, or configuring the
interrupt type.
Fixes: d5c3d84657 "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS"
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_get_gpiod_from_child() tries several property suffixes to find a
GPIO descriptor. If all suffixes fail and no probe deferral has been
detected, it returns the error of the last try.
However, if any but the last try fails with a real error (e.g. -EBUSY),
this error is not propagated, and -ENOENT will be returned.
This confuses drivers that e.g. want to detect if a GPIO is already in
use.
To fix this, change the loop logic to continue on -ENOENT, which
indicates the property was not found and the next suffix should be
tried, and propagate all other detected errors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Support Opensource <support.opensource@diasemi.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call of gpiochip_remove() from error path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Ray Jui <rjui@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from error path.
Also remove the need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from error path.
Also remove the need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from error path.
Also remove the need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Add device managed APIs devm_gpiochip_add_data() and
devm_gpiochip_remove() for the APIs gpiochip_add_data()
and gpiochip_remove().
This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
This fixes the wrongly indicated lines in the userspace
ABI: test for the right BITS, do not treat bit numbers as
bitmasks.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If spi_read() fails then we just returned but we missed unlocking the
mutex.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable X-Gene standby GPIO controller as interrupt controller to provide
its own resources. This avoids ambiguity where GIC interrupt resource is
use as X-Gene standby GPIO interrupt resource in user driver.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a GPIO line ABI for getting name, label and a few select
flags from the kernel.
This hides the kernel internals and only tells userspace what it
may need to know: the different in-kernel consumers are masked
behind the flag "kernel" and that is all userspace needs to know.
However electric characteristics like active low, open drain etc
are reflected to userspace, as this is important information.
We provide information on all lines on all chips, later on we will
likely add a flag for the chardev consumer so we can filter and
display only the lines userspace actually uses in e.g. lsgpio,
but then we first need an ABI for userspace to grab and use
(get/set/select direction) a GPIO line.
Sample output from "lsgpio" on ux500:
GPIO chip: gpiochip7, "8011e000.gpio", 32 GPIO lines
line 0: unnamed unlabeled
line 1: unnamed unlabeled
(...)
line 25: unnamed "SFH7741 Proximity Sensor" [kernel output open-drain]
line 26: unnamed unlabeled
(...)
Tested-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio_chip label is useful for userspace to understand what
kind of GPIO chip it is dealing with. Let's store a copy of this
label in the gpio_device, add it to the struct passed to userspace
for GPIO_GET_CHIPINFO_IOCTL and modify lsgpio to show it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just as it says: after adding the proper interfaces to gpiolib,
this is no longer needed.
Suggested-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ks8695 gpio driver has its own copy of the irq_to_gpio()
function. This is completely unused in the mainline kernel
after we converted all remaining users several years ago,
so we can remove the definition as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The use of kmalloc() to allocate the gpio_device leaves the contained struct
device object in an unknown state. Calling dev_set_name() on a struct device
of unknown state can trigger the free() of an invalid pointer, as seen in the
following backtrace (collected by Tony Lindgren):
kfree
kobject_set_name_vargs
dev_set_name
gpiochip_add_data
omap_gpio_probe
platform_drv_probe
...
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since devm_kzalloc can be failed in memory pressure,
it needs to check and return -ENOMEM
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .direction_output callback should set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .direction_output callback should set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My left hand merges code to privatize the descriptor handling
while my right hand merges drivers that poke around and
disrespect with the same gpiolib internals.
So let's expose the proper APIs for drivers to ask the gpiolib
core if a line is marked as open drain or open source and
get some order around things so this driver compiles again.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a possible NULL pointer deference in the function,
davinci_gpio_probe due to the function, gpio2regs being able
to return a NULL pointer if it rans to get the registers for
the gpio devices on a davinci board. Furthermore if this does
arise return -ENXIO to signal callers that this case has arisen
and avoiding setting the regs or other pointer values on the
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No flags are required for bgpio_init in the TS-4800 gpio driver. This
patch set zero instead. The driver will have the same behaviour since
the & operator between the flags already resulted to zero.
Fixes: 5041e79144 ("gpio: add TS-4800 fpga GPIO support")
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We move to manage this pointer under gpiolib control rather than
leave it in the subdevice's gpio_chip. We can not NULL it after
gpiochip_remove so at to keep things tight.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of keeping this reference to the pin ranges in the
client driver-supplied gpio_chip, move it to the internal
gpio_device as the drivers have no need to inspect this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the WinSystems WS16C48 GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the SMSC SCH311x GPIO driver, a
corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the Intel ICH series GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the AMD 8111 GPIO driver, a
corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the ACCES 104-IDIO-16 GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the ACCES 104-IDI-48 GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the ACCES 104-DIO-48E GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO driver copyright boilerplate lacks the "or
later" verbiage regarding GPL compliant distribution. The MODULE_LICENSE
string should reflect the actual copyright license terms used.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Every time a descriptor is retrieved from the gpiolib, we issue
module_get() to reference count the module supplying the GPIOs.
We also need to call device_get() and device_put() as we also
reference the backing gpio_device when doing this.
Since the sysfs GPIO interface is using gpiod_get() this will
also reference count the sysfs requests until all GPIOs are
unexported.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some information about the GPIO chip need to stay around also
after the gpio_chip has been removed and only the gpio_device
persist. The base and ngpio are such things, for example we
don't want a new chip arriving to overlap the number space
of a dangling gpio_device, and the chardev may still query
the device for the number of lines etc.
Note that the code that assigns base and insert gpio_device
into the global list no longer check for a missing gpio_chip:
we respect the number space allocated by any other gpio_device.
As a consequence of the gdev being referenced directly from
the gpio_desc, we need to verify it differently from all
in-kernel API calls that fall through to direct queries to
the gpio_chip vtable: we first check that desc is !NULL, then
that desc->gdev is !NULL, then, if desc->gdev->chip is NULL,
we *BAIL OUT* without any error, so as to manage the case
where operations are requested on a device that is gone.
These checks were non-uniform and partly missing in the past:
so to simplify: create the macros VALIDATE_DESC() that will
return -EINVAL if the desc or desc->gdev is missing and just
0 if the chip is gone, and conversely VALIDATE_DESC_VOID()
for the case where the function does not return an error.
By using these macros, we get warning messages about missing
gdev with reference to the right function in the kernel log.
Despite the macro business this simplifies the code and make
it more readable than if we copy/paste the same descriptor
checking code into all code ABI call sites (IMHO).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This kind of hacks disturbs the refactoring of the gpiolib.
The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the device core reference count for the device goes to
0 and it calls .release() we free resources and so can also
finally free up the GPIO state container, struct gpio_device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the TPS65912 PMIC GPIOs.
TPS65912 has five configurable GPIOs that can be used for several
purposes.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver for the GPIO block found in ti's tps65218 pmics.
The device has two GPIOs and one GPO pin which can be configured as follows:
GPIO1:
-general-purpose, open-drain output controlled by GPO1 user bit and/or
sequencer
-DDR3 reset input signal from SOC. Signal is either latched or
passed-trough to GPO2 pin. See below for details.
GPO2:
-general-purpose output controlled by GPO2 user bit
-DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD.
See below for details.
-Output buffer can be configured as open-drain or push-pull.
GPIO3:
-general-purpose, open-drain output controlled by GPO3 user bit and/or
sequencer
-reset input-signal for DCDC1 and DCDC2.
The input configurations are not meant to be used by the user so the driver
only offers GPOs.
v2: Added request routine that evaluates the fw config flags and removed module
owner
v3: Added .direction_input() routine, and took care of all Linus Walleij
suggestions (clamp to bool, use proper include)
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for TI TPIC2810 8-Bit LED Driver with I2C Interface.
The TPIC2810 has 8 open-drain outputs that can but used to drive
LEDs and other low-side switched resistive loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic parallel-in/serial-out shift register GPIO driver.
This includes SPI compatible devices like SN74165 serial-out shift
registers and the SN65HVS88x series of industrial serializers that can
be read over the SPI bus and used for GPI (General Purpose Input).
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add myself to the copyright list and remove the reference to Atheros'
BSP as nothing is left of this code.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the interrupt controller using GPIOLIB_IRQCHIP.
Both edges isn't supported by the chip and has to be emulated
by switching the polarity on each interrupt.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we now allow the driver to be built as a module it should be
removable.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow building the driver in compile tests we must drop the
dependency on asm/mach-ath79/ar71xx_regs.h. For this we replace the
include with local definition of the registers needed for this driver.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop most of the code in favor of the generic MMIO GPIO driver.
As the driver now depend on CONFIG_GPIO_GENERIC also add a Kconfig
entry to make the driver optional.
We leave the base pointer and lock in the data struct because they are
needed for the IRQ support.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new chardev that is to be used for userspace GPIO access is
added in this patch. It is intended to gradually replace the
horribly broken sysfs ABI.
Using a chardev has many upsides:
- All operations are per-gpiochip, which is the actual
device underlying the GPIOs, making us tie in to the
kernel device model properly.
- Hotpluggable GPIO controllers can come and go, as this
kind of problem has been know to userspace for character
devices since ages, and if a gpiochip handle is held in
userspace we know we will break something, whereas the
sysfs is stateless.
- The one-value-per-file rule of sysfs is really hard to
maintain when you want to twist more than one knob at a time,
for example have in-kernel APIs to switch several GPIO
lines at the same time, and this will be possible to do
with a single ioctl() from userspace, saving a lot of
context switching.
We also need to add a new bus type for GPIO. This is
necessary for example for userspace coldplug, where sysfs is
traversed to find the boot-time device nodes and create the
character devices in /dev.
This new chardev ABI is *non* *optional* and can be counted
on to be present in the future, emphasizing the preference
of this ABI.
The ABI only implements one single ioctl() to get the name
and number of GPIO lines of a chip. Even this is debatable:
see it as a minimal example for review. This ABI shall be
ruthlessly reviewed and etched in stone.
The old /sys/class/gpio is still optional to compile in,
but will be deprecated.
Unique device IDs are created using IDR, which is overkill
and insanely scalable, but also well tested.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use the new struct device inside gpio_chip to related debug
prints and warnings, and we also add it to the debugfs dump.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.
When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.
If sysfs is active, it will use this device as parent.
We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.
The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.
From this point on, gpiochips are devices.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new Layerscape platforms has the same ip block/controller
as GPIO on PowerPC platforms(MPC8XXX), but the GPIO registers
may be big or little endian. So the code needs to get the
endian property from DTB, then make additional functions to
fit all the PowerPC/Layerscape GPIO register read/write
operations.
gpio-generic.c provides an universal infrastructure for both
big and little endian register operations. So switch the
gpio-mpc8xxx to use gpio-generic can simplify the driver and
reduce a lot of code.
The IRQ and some workaround parts in gpio-mpc8xxx.c will be
updated with the new API interfaces but following the
original functionalities.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS-4800 GPIO driver provide support for the GPIOs available
on the Technologic Sytems board FPGA. It allows to set
direction and read/write states.
It uses the generic gpio driver.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add F81866 GPIO supports
Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.
Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html
The control method is the same with F7188x, but we should care the address
of GPIO8x.
GPIO address is below:
GPIO0x based: 0xf0
GPIO1x based: 0xe0
GPIO2x based: 0xd0
GPIO3x based: 0xc0
GPIO4x based: 0xb0
GPIO5x based: 0xa0
GPIO6x based: 0x90
GPIO7x based: 0x80
GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDI-48 can differentiate between its own and other
devices' interrupt requests. Therefore, IRQ sharing is possible and
should be permitted.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On failure to setup the irq altera_gpio_probe would return an error
but not go to cleanup. This resulted in kernel fault
"Unable to handle kernel paging request at virtual address xxxxxxxx"
later on in of_gpiochip_find_and_xlate.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull input updates from Dmitry Torokhov:
- new driver for eGalaxTouch serial touchscreen
- new driver for TS-4800 touchscreen
- an update for Goodix touchscreen driver
- PS/2 mouse module was reworked to limit number of protocols we try on
pass-through ports to speed up their detection time
- wacom_w8001 touchscreen driver now reports pen and touch via separate
instances of input devices
- other driver changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
Input: elantech - mark protocols v2 and v3 as semi-mt
Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
Input: gpio-keys - fix check for disabling unsupported keys
Input: omap-keypad - remove dead check
Input: ti_am335x_tsc - fix HWPEN interrupt handling
Input: omap-keypad - set tasklet data earlier
Input: rohm_bu21023 - fix handling of retrying firmware update
Input: ALPS - report v3 pinnacle trackstick device only if is present
Input: ALPS - detect trackstick presence for v7 protocol
Input: pcap_ts - use to_delayed_work
Input: bma150 - constify bma150_cfg structure
Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
Input: egalax_ts_serial - fix potential NULL dereference on error
Input: uinput - sanity check on ff_effects_max and EV_FF
Input: uinput - rework ABS validation
Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
Input: goodix - add axis swapping and axis inversion support
Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
Input: goodix - add power management support
...
In some situations the gpio_list order is not correct.
As a consequence gpiochip_find_base returns the same
base number twice. This happens when a first ship is added
with manual base number, then other ships are added using
automatic base number.
To prevent this behaviour, this patch add the new chip after
the last element of the gpio list.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 709d71a17c ("gpio: mpc8xxx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.
Fixes: 709d71a17c ("gpio: mpc8xxx: use gpiochip data pointer")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 6aa7dbfa28 ("gpio: mm-lantiq: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.
Fixes: 6aa7dbfa28 ("gpio: mm-lantiq: use gpiochip data pointer")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CS47L24 and WM1831 codecs only have two GPIO lines, but are
otherwise similar to the WM8280.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
BMIPS_GENERIC (arch/mips/bmips) is the Kconfig symbol associated with
Broadcom MIPS-based STB chips. Since this driver is perfectly usable on
these platforms as well, allow using it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Broadcom MIPS-based STB chips endianness is configured by boot strap,
which also reverses all bus endianness (i.e., big-endian CPU + big
endian bus ==> native endian I/O).
Other architectures (e.g., ARM) either do not support big endian, or
else leave I/O in little endian mode.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A cleanup patch replaced bgpio_chip with gpio_chip but missed
two references to the bgpio_chip:
drivers/gpio/gpio-moxart.c:60:19: error: use of undeclared identifier 'bgc'; did you mean 'gc'?
gc->bgpio_data = bgc->read_reg(bgc->reg_set);
drivers/gpio/gpio-moxart.c:35:20: note: 'gc' declared here
drivers/gpio/gpio-moxart.c:60:33: error: use of undeclared identifier 'bgc'; did you mean 'gc'?
gc->bgpio_data = bgc->read_reg(bgc->reg_set);
This adds the missing change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0f4630f372 ("gpio: generic: factor into gpio_chip struct")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 097d88e94c ("gpio: xilinx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). Unfortunately, the
data pointer is not yet set by the time xgpio_save_regs() is called,
causing a system hang.
Fixes: 097d88e94c ("gpio: xilinx: use gpiochip data pointer")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The double negation is costly and can be avoided by shifting the
register value before masking the requested bit.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For completion, sweep the floor from all gpiochip_add() usage so
we can remove that function and get rid of the function wrapper
gpiochip_add().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Cc: Margarita Olaya <magi@slimlogic.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-By: Rhyland Klein <rklein@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Daniel Mack <zonque@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Thierry Reding <treding@nvidia.com>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Toby Smith <toby@tismith.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Andrew Chew <achew@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Reviewed-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Feng Tang <feng.tang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: wu guoxing <b39297@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-By: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Nicholas Krause <xerofoify@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Milo Kim <milo.kim@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Brunner Michael <Michael.Brunner@kontron.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Zhu, Lejun <lejun.zhu@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michael Buesch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Markus Mayer <markus.mayer@linaro.org>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: YD Tseng <ltyu101@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The separate struct bgpio_chip has been a pain to handle, both
by being confusingly similar in name to struct gpio_chip and
for being contained inside a struct so that struct gpio_chip
is contained in a struct contained in a struct, making several
steps of dereferencing necessary.
Make things simpler: include the fields directly into
<linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and
get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix
some of the member variables with bgpio_* and add proper
kerneldoc while we're at it.
Modify all users to handle the change and use a struct
gpio_chip directly. And while we're at it: replace all
container_of() dereferencing by gpiochip_get_data() and
registering the gpio_chip with gpiochip_add_data().
Cc: arm@kernel.org
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the same spirit as we add an optional void *data argument
to the gpiochip_add_data() call, we need this also for
of_mm_gpiochip_add().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a void * pointer to gpio_chip so that driver can
assign and retrieve some states. This is done to get rid of
container_of() calls for gpio_chips embedded inside state
containers, so we can remove the need to have the gpio_chip
or later (planned) struct gpio_device be dynamically allocated
at registration time, so that its struct device can be properly
reference counted and not bound to its parent device (e.g.
a platform_device) but instead live on after unregistration
if it is opened by e.g. a char device or sysfs.
The data is added with the new function gpiochip_add_data()
and for compatibility we add static inline wrapper function
gpiochip_add() that will call gpiochip_add_data() with
NULL as argument. The latter will be removed once we have
exorcised gpiochip_add() from the kernel.
gpiochip_get_data() is added as a static inline accessor
for drivers to quickly get their data out.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cppcheck reports this:
(style) int result is returned as long value. If the return
value is long to avoid loss of information, then you have
loss of information.
This can be fixed with (1UL << pin) but that is the same
as using <linux/bitops.h> that already use 1UL so take
this approach.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO is used as an interrupt in ACPI, the irq_type was not
available for device driver.
Make available polarity and triggering information in acpi_find_gpio by
renaming acpi_gpio_info field active_low to polarity and adding triggering
field (edge/level).
For sanity, in gpiolib.c replace info.active_low by
"info.polarity == GPIO_ACTIVE_LOW".
Set the irq_type if necessary in acpi_dev_gpio_irq_get.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We were getting build warning about "iterator" being used uninitialized.
Use iterator properly to fix the build warning and in the process remove
the variable "pos" which is not required now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 45ad7db90b.
We have fixed all the drivers that were returning ambious values
not clamped to [0,1] or an error code, so return the error
propagating behaviour of the API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This also makes the driver start to return the error code, as the
end of the series make this work.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This also starts to propagate the error code from the I2C
transaction as the end of the series adds support for that.
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also start returning the error code if something fails, as the
end of the series augment the core to support this.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Feng Tang <feng.tang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also start to propagate the error code here as the end of the
series fixes this to work for all drivers.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by:Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Roland Stigge <stigge@antcom.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Brunner Michael <Michael.Brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Paul Gortmaker