Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Alas the method trigger_all_cpu_backtrace() isn't exported by the
kernel, but we need to have it called in case of the bus errors detected
to get a better description of a possible cause of the error. Let's
disable the ability to build the driver as a loadable kernel module then.
Note In future the driver will support the AXI-bus interconnect capability,
so we'd have to make it built into the kernel anyway.
Link: https://lore.kernel.org/r/20200528193113.17372-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Seeing trigger_all_cpu_backtrace() isn't exported from the kernel and
since calling it is a very important part of driver, which may provide
a better description of a possible cause of the error, let's disable the
ability to build the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20200528193113.17372-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is a ready-to-use method to compare a retrieved from a sysfs node
string with another string. It treats both NUL and newline-then-NUL as
equivalent string terminations. So use it instead of manually truncating
the line length in the strncmp() method.
Link: https://lore.kernel.org/r/20200528145050.5203-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It's better to have a single return statement where it's applicable
instead of returning from a conditional statement if-clause. Let's
do this in the request registers, clock and IRQ methods.
Link: https://lore.kernel.org/r/20200528145050.5203-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is a ready-to-use method to compare a retrieved from a sysfs node
string with another string. It treats both NUL and newline-then-NUL as
equivalent string terminations. So use it instead of manually truncating
the line length in the strncmp() method.
Link: https://lore.kernel.org/r/20200528145050.5203-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Indeed it's more optimal to use the PTR_ERR_OR_ZERO() macro there instead
of having two return points.
Link: https://lore.kernel.org/r/20200528145050.5203-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After fixing the sysfs calback return value the functions argumnets
identations have been left as before the fix. That made the
argments declarations being unaligned with respect to the space
surrounded by the parentheses.
Link: https://lore.kernel.org/r/20200528145050.5203-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It must be included since we are using readl() method here.
Link: https://lore.kernel.org/r/20200528145050.5203-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Olof Johansson <olof@lixom.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: soc@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Baikal-T1 AXI-APB bridge is used to access the SoC subsystem CSRs.
IO requests are routed to this bus by means of the DW AMBA 3 AXI
Interconnect. In case if an attempted APB transaction stays with no
response for a pre-defined time an interrupt occurs and the bus gets
freed for a next operation. This driver provides the interrupt handler
to detect the erroneous address, prints an error message about the
address fault, updates an errors counter. The counter and the APB-bus
operations timeout can be accessed via corresponding sysfs nodes.
A dedicated sysfs-node can be also used to artificially cause the
bus errors described above.
[arnd: fix build warnings for missing includes and wrong return types]
Link: https://lore.kernel.org/r/20200526125928.17096-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: soc@kernel.org
Cc: devicetree@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AXI3-bus is the main communication bus connecting all high-speed
peripheral IP-cores with RAM controller and MIPS P5600 cores on Baikal-T1
SoC. Bus traffic arbitration is done by means of DW AMBA 3 AXI
Interconnect (so called AXI Main Interconnect) routing IO requests from
one SoC block to another. This driver provides a way to detect any bus
protocol errors and device not responding situations by means of an
embedded on top of the interconnect errors handler block (EHB). AXI
Interconnect QoS arbitration tuning is currently unsupported.
The bus doesn't provide a way to detect the interconnected devices,
so they are supposed to be statically defined like by means of the
simple-bus sub-nodes.
[arnd: fix build warnings for missing includes and wrong return types]
Link: https://lore.kernel.org/r/20200526125928.17096-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: soc@kernel.org
Cc: devicetree@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
-----BEGIN PGP SIGNATURE-----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=07SB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
System timer changes for omaps for v5.8 merge window
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
* tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
ARM: dts: Configure system timers for omap3
ARM: dts: Configure system timers for omap5 and dra7
ARM: dts: Configure system timers for omap4
ARM: dts: Configure system timers for am437x
ARM: dts: Configure system timers for am335x
ARM: OMAP2+: Add omap_init_time_of()
bus: ti-sysc: Ignore timer12 on secure omap3
clk: ti: dm816: enable sysclk6_ck on init
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
Link: https://lore.kernel.org/r/pull-1590169577-735045@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The MHI device may be in the syserr state when we attempt to init it in
power_up(). Since we have no local state, the handling is simple -
reset the device and wait for it to transition out of the reset state.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take write lock only to protect db_mode member of mhi channel.
This allows rest of the mhi channels to just take read lock which
fine grains the locking. It prevents channel readers to starve if
they try to enter critical section after a writer.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices that support RDDM do not require processing SYS_ERROR as it is
deemed redundant. Avoid SYS_ERROR processing if RDDM is supported by
the device.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver continues handling of BHI interrupt even if MHI register access
is not allowed. By doing so it calls the status call back and performs
early notification for the MHI client. This is not needed when MHI
register access is not allowed. Hence skip the handling in this case and
return. Also add debug log to print device state, local EE and device EE
when reg access is valid.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mission mode transition is handled by state worker thread but
power off is not. There is a possibility while mission mode
transition is in progress which calls MHI client driver probe,
power off is issued by MHI controller. This results into client
driver probe and remove running in parallel and causes use after
free situation. By queuing disable transition work when mission
mode is in progress prevents the race condition.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the system error worker thread and instead have the
execution environment worker handle that transition to serialize
processing and avoid any possible race conditions during
shutdown.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While writing any sequence or session identifiers, it is possible that
the host could write a zero value, whereas only non-zero values should
be supported writes to those registers. Ensure that the host does not
write a non-zero value for them and also log them in debug messages. A
macro is introduced to simplify this check and the existing checks are
also converted to use this macro.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading AMSS firmware using BHIe protocol, return -ETIMEDOUT if no
response is received within the timeout or return -EIO in case of a
protocol returned failure or an MHI error state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon power up, driver queues firmware worker thread if the execution
environment is PBL. Firmware worker is blocked with a timeout until
state worker gets a chance to run and unblock firmware worker. An
endpoint power up failure can be seen if state worker gets a chance to
run after firmware worker has timed out. Remove this dependency and
handle firmware load directly using state worker thread.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MHI Driver receives an EOT event, it reads xfer_len from the
event in the last TRE. The value is under control of the MHI device
and never validated by Host MHI driver. The value should never be
larger than the real size of the buffer but a malicious device can
set the value 0xFFFF as maximum. This causes driver to memory
overflow (both read or write). Fix this issue by reading minimum of
transfer length from event and the buffer length provided.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI data completion handler function reads channel id from event
ring element. Value is under the control of MHI devices and can be
any value between 0 and 255. In order to prevent out of bound access
add a bound check against the max channel supported by controller
and skip processing of that event ring element.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver is using zero initialized intmod value from mhi channel when
configuring TRE for bei field. This prevents interrupt moderation to
take effect in case it is supported by an event ring. Fix this by
copying intmod value from associated event ring to mhi channel upon
registering mhi controller.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all the common code to generate TRE from mhi_queue_buf,
mhi_queue_dma and mhi_queue_skb to mhi_gen_tre. This helps
to centralize the TRE generation code which makes any future
bug fixing easier to manage in these APIs.
Suggested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As timers no longer need legacy quirk handling, let's move them to
the CONFIG_DEBUG section to make it easier to see which drivers still
need more work.
Let's also add detection for few more older timer revisions while at
it as that makes CONFIG_DEBUG output easier to read with proper names.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some early omap3 boards use timer12 for system timer, but for secure
SoCs like on n900 it's not accessible. Likely we will be configuring
unavailable devices for other SoCs too based on runtime SoC detection,
so let's use a switch to start with.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series enables building various Versatile Express platform drivers
as modules. The primary target is the Fast Model FVP which is supported
in Android. As Android is moving towards their GKI, or generic kernel,
the hardware support has to be in modules. Currently ARCH_VEXPRESS
enables several built-in only drivers. Some of these are needed, but
some are only needed for older 32-bit VExpress platforms and can just
be disabled.
-----BEGIN PGP SIGNATURE-----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=c5eS
-----END PGP SIGNATURE-----
Merge tag 'vexpress-modules-for-soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into arm/soc
VExpress modularization
This series enables building various Versatile Express platform drivers
as modules. The primary target is the Fast Model FVP which is supported
in Android. As Android is moving towards their GKI, or generic kernel,
the hardware support has to be in modules. Currently ARCH_VEXPRESS
enables several built-in only drivers. Some of these are needed, but
some are only needed for older 32-bit VExpress platforms and can just
be disabled.
* tag 'vexpress-modules-for-soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: vexpress: Don't select VEXPRESS_CONFIG
bus: vexpress-config: Support building as module
vexpress: Move setting master site to vexpress-config bus
bus: vexpress-config: simplify config bus probing
bus: vexpress-config: Merge vexpress-syscfg into vexpress-config
mfd: vexpress-sysreg: Support building as a module
mfd: vexpress-sysreg: Use devres API variants
mfd: vexpress-sysreg: Drop unused syscon child devices
mfd: vexpress-sysreg: Drop selecting CONFIG_CLKSRC_MMIO
clk: vexpress-osc: Support building as a module
clk: vexpress-osc: Use the devres clock API variants
clk: versatile: Only enable SP810 on 32-bit by default
clk: versatile: Rework kconfig structure
amba: Retry adding deferred devices at late_initcall
arm64: vexpress: Don't select CONFIG_POWER_RESET_VEXPRESS
ARM: vexpress: Move vexpress_flags_set() into arch code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix to return negative error code from the error handling case
instead of 0 in mhi_init_dev_ctxt() and mhi_driver_probe().
Fixes: 3000f85b8f ("bus: mhi: core: Add support for basic PM operations")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200509075654.175002-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's only a single caller of vexpress_config_set_master() from
vexpress-sysreg.c. Let's just make the registers needed available to
vexpress-config and move all the code there. The registers needed aren't
used anywhere else either. With this, we can get rid of the private API
between these 2 drivers.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The vexpress-config initialization is dependent on the vexpress-syscfg
driver probing. As vexpress-config was not a driver, deferred probe
could not be used and instead initcall ordering was relied upon. This is
fragile and doesn't work for modules.
Let's move the config bus init into the vexpress-syscfg probe. This
eliminates the initcall ordering requirement and the need to create a
struct device and the "vexpress-config" class.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The only thing that vexpress-syscfg does is provide a regmap to
vexpress-config bus child devices. There's little reason to have 2
components for this. The current structure with initcall ordering
requirements makes turning these components into modules more difficult.
So let's start to simplify things and merge vexpress-syscfg into
vexpress-config. There's no functional change in this commit and it's
still separate components until subsequent commits.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When multiple instances of the same MHI product are present in a system,
we can see a splat from mhi_create_devices() - "sysfs: cannot create
duplicate filename".
This is because the device names assigned to the MHI channel devices are
non-unique. They consist of the channel's name, and the channel's pipe
id. For identical products, each instance is going to have the same
set of channel (both in name and pipe id).
To fix this, we prepend the device name of the parent device that the
MHI channels belong to. Since different instances of the same product
should have unique device names, this makes the MHI channel devices for
each product also unique.
Additionally, remove the pipe id from the MHI channel device name. This
is an internal detail to the MHI product that provides little value, and
imposes too much device specific internal details to userspace. It is
expected that channel with a specific name (ie "SAHARA") has a specific
client, and it does not matter what pipe id that channel is enumerated on.
The pipe id is an internal detail between the MHI bus, and the hardware.
The client is not expected to make decisions based on the pipe id, and to
do so would require the client to have intimate knowledge of the hardware,
which is inappropiate as it may violate the layering provided by the MHI
bus. The limitation of doing this is that each product may only have one
instance of a channel by a unique name. This limitation is appropriate
given the usecases of MHI channels.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading or writing MHI registers, the core assumes that the physical
link is a memory mapped PCI link. This assumption may not hold for all
MHI devices. The controller knows what is the physical link (ie PCI, I2C,
SPI, etc), and therefore knows the proper methods to access that link.
The controller can also handle link specific error scenarios, such as
reading -1 when the PCI link went down.
Therefore, it is appropriate that the MHI core requests the controller to
make register accesses on behalf of the core, which abstracts the core
from link specifics, and end up removing an unnecessary assumption.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the MHI core detects invalid data due to a PCI read, it calls into
the controller via link_status() to double check that the link is infact
down. All in all, this is pretty pointless, and racy. There are no good
reasons for this, and only drawbacks.
Its pointless because chances are, the controller is going to do the same
thing to determine if the link is down - attempt a PCI access and compare
the result. This does not make the link status decision any smarter.
Its racy because its possible that the link was down at the time of the
MHI core access, but then recovered before the controller access. In this
case, the controller will indicate the link is not down, and the MHI core
will precede to use a bad value as the MHI core does not attempt to retry
the access.
Retrying the access in the MHI core is a bad idea because again, it is
racy - what if the link is down again? Furthermore, there may be some
higher level state associated with the link status, that is now invalid
because the link went down.
The only reason why the MHI core could see "invalid" data when doing a PCI
access, that is actually valid, is if the register actually contained the
PCI spec defined sentinel for an invalid access. In this case, it is
arguable that the MHI implementation broken, and should be fixed, not
worked around.
Therefore, remove the link_status() callback before anyone attempts to
implement it.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerdown is necessary if mhi_sync_power_up fails due to a timeout, to
clean up the resources. Otherwise a BUG could be triggered when
attempting to clean up MSIs because the IRQ is still active from a
request_irq().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic modules on the Integrator/AP (Application Platform)
are logic tiles with (typically) one or a few peripheral
devices. They are most commonly used for FPGA prototyping.
Using the device tree node for logic tiles, we probe them
in order and check if the special system controller register
confirm their presence before populating the node for a tile.
This supercedes the code in arch/arm/mach-integrator/lm.[c|h]
and makes it possible to populate the tiles using the device
tree instead of boardfile-based descriptions.
Tested with all peripherals including graphics and MMC card
working fine with the IM-PD1 example tile from Arm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mhi_alloc_device() function never returns NULL, it returns error
pointers.
Fixes: da1c4f8569 ("bus: mhi: core: Add support for creating and destroying MHI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200407093133.GM68494@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for MHI suspend and resume states. While at it, the
mhi_notify() function needs to be exported as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200427075829.9304-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Pull crypto updates from Herbert Xu:
"API:
- Fix out-of-sync IVs in self-test for IPsec AEAD algorithms
Algorithms:
- Use formally verified implementation of x86/curve25519
Drivers:
- Enhance hwrng support in caam
- Use crypto_engine for skcipher/aead/rsa/hash in caam
- Add Xilinx AES driver
- Add uacce driver
- Register zip engine to uacce in hisilicon
- Add support for OCTEON TX CPT engine in marvell"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
crypto: af_alg - bool type cosmetics
crypto: arm[64]/poly1305 - add artifact to .gitignore files
crypto: caam - limit single JD RNG output to maximum of 16 bytes
crypto: caam - enable prediction resistance in HRWNG
bus: fsl-mc: add api to retrieve mc version
crypto: caam - invalidate entropy register during RNG initialization
crypto: caam - check if RNG job failed
crypto: caam - simplify RNG implementation
crypto: caam - drop global context pointer and init_done
crypto: caam - use struct hwrng's .init for initialization
crypto: caam - allocate RNG instantiation descriptor with GFP_DMA
crypto: ccree - remove duplicated include from cc_aead.c
crypto: chelsio - remove set but not used variable 'adap'
crypto: marvell - enable OcteonTX cpt options for build
crypto: marvell - add the Virtual Function driver for CPT
crypto: marvell - add support for OCTEON TX CPT engine
crypto: marvell - create common Kconfig and Makefile for Marvell
crypto: arm/neon - memzero_explicit aes-cbc key
crypto: bcm - Use scnprintf() for avoiding potential buffer overflow
crypto: atmel-i2c - Fix wakeup fail
...
Add a new api that returns Management Complex firmware version
and make the required structure public. The api's first user will be
the caam driver for setting prediction resistance bits.
Signed-off-by: Andrei Botila <andrei.botila@nxp.com>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For some scenarios like controller suspend and resume, mhi_destroy_device()
will get called without mhi_unregister_controller(). In that case, the
references to the mhi_dev created for the channels will not be dropped
but the channels will be destroyed as per the spec. This will cause issue
during resume as the channels will not be created due to the fact that
mhi_dev is not NULL.
Hence, this change decrements the refcount for mhi_dev in
mhi_destroy_device() for concerned channels and also sets mhi_dev to NULL
in release_device().
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
