Add OMAP4 CPUIDLE support. CPU1 is left with defualt idle and
the low power state for it is managed via cpu-hotplug.
This patch adds MPUSS low power states in cpuidle.
C1 - CPU0 ON + CPU1 ON + MPU ON
C2 - CPU0 OFF + CPU1 OFF + MPU CSWR
C3 - CPU0 OFF + CPU1 OFF + MPU OSWR
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWr.
Ofcourse when MPUSS and CORE PD transitions to OSWR along with device
off mode, even the memory contemts are lost which is as good as
the PD off state.
On OMAP4 because of hardware constraints, no low power states are
targeted when both CPUs are online and in SMP mode. The low power
states are attempted only when secondary CPU gets offline to OFF
through hotplug infrastructure.
Thanks to Nicole Chalhoub <n-chalhoub@ti.com> for doing exhaustive
C-state latency profiling.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the MPUSS OSWR (Open Switch Retention) support. The MPUSS
OSWR configuration is as below.
- CPUx L1 and logic lost, MPUSS logic lost, L2 memory is retained
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWR.
On OMAP4430 secure devices too, MPUSS off mode can't be used because of
a bug which alters Ducati and Tesla states. Hence MPUSS off mode as an
independent state isn't supported on OMAP44XX devices.
Ofcourse when MPUSS power domain transitions to OSWR along
with device off mode, it eventually hits off state since memory
contents are lost.
Hence the MPUSS off mode independent state is not attempted without
device off mode. All the necessary infrastructure code for MPUSS
off mode is in place as part of this series.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MPUSS(MPU Sub System) power domain
CSWR(Close Switch Retention) support to system wide suspend.
For MPUSS power domain to hit retention(CSWR or OSWR), both
CPU0 and CPU1 power domains need to be in OFF or DORMANT state,
since CPU power domain CSWR is not supported by hardware
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Default arch_idle() isn't good enough for OMAP4 because of aync bridge errata
and necessity of NOPs post WFI to avoid speculative prefetch aborts.
Hence Use OMAP4 custom omap_do_wfi() hook for default idle.
Later in the series, async bridge errata work-around patch updates the
omap_do_wfi() with necessary interconnects barriers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the CPU0 and CPU1 off mode support. CPUX close switch
retention (CSWR) is not supported by hardware design.
The CPUx OFF mode isn't supported on OMAP4430 ES1.0
CPUx sleep code is common for hotplug, suspend and CPUilde.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialise hardware supervised mode for all clockdomains if it's
supported. Initiate sleep transition for other clockdomains,
if they are not being used.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4430 ES1.0, Power Management features are not supported.
Avoid omap4_pm_init() on ES1.0 silicon so that we can continue
to use same kernel binary to boot on all OMAP4 silicons.
The ES1.0 boot failure with OMAP4 PM series was because of
the clockdomain initialisation code. Hardware supervised
clockdomain mode isn't functional for all clockdomains
on OMAP4430 ES1.0 silicon so avoid the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As per OMAP4430 TRM, the dynamic dependency between MPUSS -> EMIF
and MPUSS -> L4PER/L3_* and DUCATI -> L3_* clockdomains is enable
by default. Refer register CM_MPU_DYNAMICDEP description for details.
But these dynamic dependencies doesn't work as expected. The hardware
recommendation is to enable static dependencies for above clockdomains.
Without this, system locks up or randomly crashes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pm44xx.c is built only when CONFIG_PM is setup,
remove redundant CONFIG_PM check.
This also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=25022
Reported-by: Martin Etti <ettl.martin@gmx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP powerdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/powerdomain.h
to mach-omap2/powerdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access powerdomain code
and data directly.
As part of this process, remove the references to powerdomain data
from the GPIO "driver" and the OMAP PM no-op layer, both in plat-omap.
Change the DSPBridge code to point to the new location for the
powerdomain headers. The DSPBridge code should not be including the
powerdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.
The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).
Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for basic suspend doing a CPUx wfi
for OMAP4. All powerdomains are for now are kept programmed
in ON state.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar