It returns '0' even when a failure happens on jpeg buffer allocation
so this commit fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
RK3328 SoC has the same decoder IP block as RK3399,
lets enable VP8 decoding on RK3328.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
saa7134_i2c_eeprom_md7134_gate() function and the associated comment uses
an inverted i2c gate open / closed terminology.
Let's fix this.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix alignment checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Medion 7134 has two i2c eeproms on the same i2c bus sharing the same bus
addresses: the first one for SAA7134 chip config and the second one behind
TDA10046 DVB-T demod chip i2c gate storing its firmware.
The TV tuner on this board is not behind this i2c gate.
Due to the bus conflict described above, the card PCI SVID / SSID sometimes
gets garbled after a reboot, which makes it necessary to specify the card
model manually as an insmod option in order for it to be detected reliably.
To avoid this, let's just leave the gate permanently closed so the eeprom
chips won't clash.
The demod firmware load is done with its i2c gate closed anyway so it is
not affected by this change.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Variable retval is initialized to a value that is never read
so this assignment is redundant. Clean up the code by removing
retval completely and just return the error return from the
call to i2c_add_adapter.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Like a bunch of other MSI laptops the MS-1039 uses a 0c45:627b
SN9C201 + OV7660 webcam which is mounted upside down.
Add it to the sn9c20x flip_dmi_table to deal with this.
Cc: stable@vger.kernel.org
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If an error occurs in this function, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, introduce two labels to perform
the cleanup work.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In fdp1_open(), 'ctx' is allocated through kzalloc(). However, it is not
deallocated if v4l2_ctrl_new_std() fails, leading to a memory leak bug. To
fix this issue, free 'ctx' before going to the 'done' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In cx231xx_load_firmware(), 'p_buffer' is allocated through vmalloc() to
hold the firmware. However, after the usage, it is not deallocated, leading
to a memory leak bug.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a single imx-media mem2mem video device that uses the IPU IC PP
(image converter post processing) task for scaling and colorspace
conversion.
On i.MX6Q/DL SoCs with two IPUs currently only the first IPU is used.
The hardware only supports writing to destination buffers up to
1024x1024 pixels in a single pass, arbitrary sizes can be achieved
by rendering multiple tiles per frame.
[slongerbeam@gmail.com: use ipu_image_convert_adjust(), fix
device_run() error handling, add missing media-device header,
unregister and remove the mem2mem device in error paths in
imx_media_probe_complete() and in imx_media_remove(), updated
for sync subdev registration]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: correct two minor checkpatch issues]
[hverkuil-cisco@xs4all.nl: sparse warning: make imx6_media_probe_complete static]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If cec_notifier_cec_adap_unregister() is called before
cec_unregister_adapter() then everything is OK (and this is the
case today). But if it is the other way around, then
cec_notifier_unregister() is called first, and that doesn't
set n->cec_adap to NULL.
So if e.g. cec_notifier_set_phys_addr() is called after
cec_notifier_unregister() but before cec_unregister_adapter()
then n->cec_adap points to an unregistered and likely deleted
cec adapter. So just set n->cec_adap->notifier and n->cec_adap
to NULL for rubustness.
Eventually cec_notifier_unregister will disappear and this will
be simplified substantially.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check if cec_s_conn_info is called with a valid cec adapter,
do nothing if it is invalid.
This makes it possible to call this function even if CEC support is
disabled in the kernel config.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The older CSI drivers have camera capture interface different from the one
in the newer ones.
This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.
[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Makefile and Kconfig for the sun6i CSI driver are included in the main
Makefile / KConfig file. Since we're going to add a new CSI driver for an
older chip, and the Cedrus driver eventually, it makes more sense to put
those in our directory.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Allwinner A10 CMOS Sensor Interface is a camera capture interface also
used in later (A10s, A13, A20, R8 and GR8) SoCs.
On some SoCs, like the A10, there's multiple instances of that controller,
with one instance supporting more channels and having an ISP.
[Sakari Ailus: Add type: object to the endpoint node.]
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of sensor malfunction, stop streaming timeout takes much longer
than expected. This is due to conversion of time to jiffies: milliseconds
multiplied with HZ (ticks/second) gives out a value of jiffies with 10^3
greater. We need to also divide by 10^3 to obtain the right jiffies value.
In other words FRAME_INTERVAL_MILLI_SEC must be in seconds in order to
multiply by HZ and get the right jiffies value to add to the current
jiffies for the timeout expire time.
Fixes: 195ebc43bf ("[media] V4L: at91: add Atmel Image Sensor Interface (ISI) support")
Signed-off-by: Alexandre Kroupski <alexandre.kroupski@ingenico.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The older Allwinner SoCs have a IR receiver supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The RC controllers have a bunch of generic properties that are needed in a
device tree. Add a YAML schemas for those.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function at issue does not always initialize each byte allocated
for 'b' and can therefore leak uninitialized memory to a USB device in
the call to usb_bulk_msg()
Use kzalloc() instead of kmalloc()
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+0522702e9d67142379f1@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Static structure en_templ, of type dvb_ca_en50221, is not used except to
be copied into a local variable. Hence make it const to prevent
unintended modification of the original fields.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The static structure ec168_props, of type dvb_usb_device_properties, is
used only once, when it is assigned to field props of the constant
structure ec168_driver_info. As this means that ec168_props will never be
modified, make it const as well in order to prevent unintended
modification of its fields.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Static structure fdtv_ca, of type dvb_device, is only used when it is
passed as the third argument to function dvb_register_device(). However,
in the definition of dvb_register_device, the third parameter is
declared as constant. Hence make fdtv_ca const as well.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Static structure dst_config, of type dst_config, is not used except to
be assigned as the value of field state of a variable having type
dst_state *. In the definition of dst_state, field config is declared as
const. Hence dst_config, when assigned to config, cannot be modified.
Therefore, make dst_config const as well.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit 5fa88151ec ("[media] dvb-usb-cxusb: Geniatech T230 - resync TS
FIFO after lock") does not solve the problem for all devices. This is the
same issue reported on the T230C, which was moved to the dvbsky.c driver
to work around this issue in commit 5742240577 ("media: dvbsky: MyGica
T230C support").
In addition, the cxusb driver causes an oops when unplugging the device
while streaming; this problem does not happen any more.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove this device from the cxusb driver so it can be added to the dvbsky
driver.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This protocol responds to a real philips rc-mm remote; it does not respond
to IR encoded with the encoder in ir-rcmm-decoder.c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In cx24117_load_firmware(), 'buf' is allocated through kmalloc() to hold
the firmware. However, if i2c_transfer() fails, it is not deallocated,
leading to a memory leak bug.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In dib7000pc_detection(), 'tx' and 'rx' are allocated through kzalloc()
respectively. However, if DiB7000PC is detected, they are not deallocated,
leading to memory leaks. To fix this issue, create a label to free 'tx' and
'rx' before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is a simple NEC remote control device shipped with the HardKernel
ODROID range of SBC devices.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WeTek Play 2 Android STB ships with an unusual remote where the
main up/down/left/right/enter controls are surrounded with an outer
ring of additional keys which are listed in clockwise order.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WeTek Hub Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tanix TX5 max Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tanix TX3 mini Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Khadas VIM and Edge SBC devices use the same NEC remote device. The
remote includes a mouse button for Android use. This has been mapped
to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The X96-Max Android STB ships with a simple NEC remote. It includes
a TV section with preset buttons for controlling a TV. These are not
configurable, but are noted to aid visual recognition of the device.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cmd_init() to fill a struct si2168_cmd command.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
KASAN: global-out-of-bounds Read in dvb_pll_attach
Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).
Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.2.0-rc6+ #13
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
dvb_pll_attach+0x6c5/0x830 drivers/media/dvb-frontends/dvb-pll.c:798
dvb_pll_probe+0xfe/0x174 drivers/media/dvb-frontends/dvb-pll.c:877
i2c_device_probe+0x790/0xaa0 drivers/i2c/i2c-core-base.c:389
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
i2c_new_client_device+0x5b3/0xc40 drivers/i2c/i2c-core-base.c:778
i2c_new_device+0x19/0x50 drivers/i2c/i2c-core-base.c:821
dvb_module_probe+0xf9/0x220 drivers/media/dvb-core/dvbdev.c:985
friio_tuner_attach+0x125/0x1d0 drivers/media/usb/dvb-usb-v2/gl861.c:536
dvb_usbv2_adapter_frontend_init
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:675 [inline]
dvb_usbv2_adapter_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:804
[inline]
dvb_usbv2_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:865 [inline]
dvb_usbv2_probe.cold+0x24dc/0x255d
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:980
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023
generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210
usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_new_device.cold+0x8c1/0x1016 drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x1ada/0x3590 drivers/usb/core/hub.c:5432
process_one_work+0x905/0x1570 kernel/workqueue.c:2269
process_scheduled_works kernel/workqueue.c:2331 [inline]
worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
kthread+0x30b/0x410 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
The buggy address belongs to the variable:
id+0x100/0x120
Memory state around the buggy address:
ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00
ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
^
ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================
Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The existing documentation was incorrect and did not correspond
to how actual codec drivers implemented this.
Update the documentation to explicitly specify what is actually
expected.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Due to complexity of the video decoding process, the V4L2 drivers of
stateful decoder hardware require specific sequences of V4L2 API calls
to be followed. These include capability enumeration, initialization,
decoding, seek, pause, dynamic resolution change, drain and end of
stream.
Specifics of the above have been discussed during Media Workshops at
LinuxCon Europe 2012 in Barcelona and then later Embedded Linux
Conference Europe 2014 in Düsseldorf. The de facto Codec API that
originated at those events was later implemented by the drivers we already
have merged in mainline, such as s5p-mfc or coda.
The only thing missing was the real specification included as a part of
Linux Media documentation. Fix it now and document the decoder part of
the Codec API.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the venus vdec supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an enum_fmt format flag to specifically tag coded formats where
dynamic resolution switching is supported by the device.
This is useful for some codec drivers that can support dynamic
resolution switching for one or more of their listed coded formats. It
allows userspace to know whether it should extract the video parameters
itself, or if it can rely on the device to send V4L2_EVENT_SOURCE_CHANGE
when such changes are detected.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an enum_fmt format flag to specifically tag coded formats where
full bytestream parsing is supported by the device.
Some stateful decoders are capable of fully parsing a bytestream,
but others require that userspace pre-parses the bytestream into
frames or fields (see the corresponding pixelformat descriptions
for details).
If this flag is set, then this pre-parsing step is not required
(but still possible, of course).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
