The max depth of a fastreg mr depends on whether the device supports
DSGL or not. So compute it dynamically based on the device support
and the module use_dsgl option.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a race when moving a QP from RTS->CLOSING where a SQ work
request could be posted after the FW receives the RDMA_RI/FINI WR.
The SQ work request will never get processed, and should be completed
with FLUSHED status. Function c4iw_flush_sq(), however was dropping
the oldest SQ work request when in CLOSING or IDLE states, instead of
completing the pending work request. If that oldest pending work
request was actually complete and has a CQE in the CQ, then when that
CQE is proceessed in poll_cq, we'll BUG_ON() due to the inconsistent
SQ/CQ state.
This is a very small timing hole and has only been hit once so far.
The fix is two-fold:
1) c4iw_flush_sq() MUST always flush all non-completed WRs with FLUSHED
status regardless of the QP state.
2) In c4iw_modify_rc_qp(), always set the "in error" bit on the queue
before moving the state out of RTS. This ensures that the state
transition will not happen while another thread is in
post_rc_send(), because set_state() and post_rc_send() both aquire
the qp spinlock. Also, once we transition the state out of RTS,
subsequent calls to post_rc_send() will fail because the "in error"
bit is set. I don't think this fully closes the race where the FW
can get a FINI followed a SQ work request being posted (because
they are posted to differente EQs), but the #1 fix will handle the
issue by flushing the SQ work request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Some HW platforms can reorder read operations, so we must rmb() after
we see a valid gen bit in a CQE but before we read any other fields
from the CQE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1) timedout endpoint processing can be starved. If there are continual
CPL messages flowing into the driver, the endpoint timeout
processing can be starved. This condition exposed the other bugs
below.
Solution: In process_work(), call process_timedout_eps() after each CPL
is processed.
2) Connection events can be processed even though the endpoint is on
the timeout list. If the endpoint is scheduled for timeout
processing, then we must ignore MPA Start Requests and Replies.
Solution: Change stop_ep_timer() to return 1 if the ep has already been
queued for timeout processing. All the callers of stop_ep_timer() need
to check this and act accordingly. There are just a few cases where
the caller needs to do something different if stop_ep_timer() returns 1:
1) in process_mpa_reply(), ignore the reply and process_timeout()
will abort the connection.
2) in process_mpa_request, ignore the request and process_timeout()
will abort the connection.
It is ok for callers of stop_ep_timer() to abort the connection since
that will leave the state in ABORTING or DEAD, and process_timeout()
now ignores timeouts when the ep is in these states.
3) Double insertion on the timeout list. Since the endpoint timers
are used for connection setup and teardown, we need to guard
against the possibility that an endpoint is already on the timeout
list. This is a rare condition and only seen under heavy load and
in the presense of the above 2 bugs.
Solution: In ep_timeout(), don't queue the endpoint if it is already on
the queue.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
[ Fix cast from u64* to integer. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will be
arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath and
ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc. from
intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJTPYBnAAoJEENa44ZhAt0hGI4P/29eotGwpkANUQE6FQvxCUL2
CXJtSg52lmYvGJrPK4IhihpbtQmHJz3iXEzlOOWidTw1dJgObR6vFaRymh7+vDLs
CdzybMcXdasarqTuYeJbFzhkimpwtWWrMy/8Ik/Jj/5glGQ6cUSpdYZzVtFhYNqf
hCGE8iLi+tuekJJj1htut5D6apXM7udcdc2yLJNOdsSj/VUXt1oqG1x9xAi9R8Tq
7o8eFSStdlja0EBQ6Hli2zauCSnQkaUtr8h6EAFbcCtvBK8HqsHSc2gfq2ViFUiN
ztt167oWoQnVkR0qCPL5nVt+CRQHHROprVXvbpcTI3aW61gNIl6OrUUOXefzHXac
TNi+fdMpiEB/JQ4Z04Jzd1dGCSjYeTqPj4rO4meFjBmxRDdTgZHu7FWwejT1nYJ5
d2abVdCOT+QWlIlM7m/pjdWJII5OYM+4/jtTayGepEaR4fTUzKtPZPBLNUBDBKE+
4f92PC8LiuPkwJgb6XT96onPz1bDCOnPSEdwoKUFKPeGUcwgVOM/Wx5NU4Yf7rfg
RxQwZ7mJXbjCYFlmGGo/0QDy6UEGkIFYlJSzooP+wlK1JvZ5h2M+9QKX2FtwzR+R
I2kBxcTXWsM/h88R7MkNqbNIllmhssrJwmAE46OneZbfoBOB+JZjb4nLRTu0jEcS
zn6f16GmJ37BKn2/qYY/
=Ww6H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.15:
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will
be arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath
and ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc.
from intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (102 commits)
RDMA/ocrdma: Unregister inet notifier when unloading ocrdma
RDMA/ocrdma: Fix warnings about pointer <-> integer casts
RDMA/ocrdma: Code clean-up
RDMA/ocrdma: Display FW version
RDMA/ocrdma: Query controller information
RDMA/ocrdma: Support non-embedded mailbox commands
RDMA/ocrdma: Handle CQ overrun error
RDMA/ocrdma: Display proper value for max_mw
RDMA/ocrdma: Use non-zero tag in SRQ posting
RDMA/ocrdma: Memory leak fix in ocrdma_dereg_mr()
RDMA/ocrdma: Increment abi version count
RDMA/ocrdma: Update version string
be2net: Add abi version between be2net and ocrdma
RDMA/ocrdma: ABI versioning between ocrdma and be2net
RDMA/ocrdma: Allow DPP QP creation
RDMA/ocrdma: Read ASIC_ID register to select asic_gen
RDMA/ocrdma: SQ and RQ doorbell offset clean up
RDMA/ocrdma: EQ full catastrophe avoidance
RDMA/cxgb4: Disable DSGL use by default
RDMA/cxgb4: rx_data() needs to hold the ep mutex
...
Current hardware doesn't correctly support DSGL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To avoid racing with other threads doing close/flush/whatever, rx_data()
should hold the endpoint mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a race between ULP threads doing an accept/reject, and the
ingress processing thread handling close/abort for the same connection.
The accept/reject path needs to hold the lock to serialize these paths.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
[ Fold in locking fix found by Dan Carpenter <dan.carpenter@oracle.com>.
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
If kmalloc() fails in c4iw_alloc_ucontext(), the function
leaves but does not set an error code in ret variable:
it will return 0 to the caller.
This patch set ret to -ENOMEM in such case.
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Steve Wise <swise@chelsio.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These are generated by HW in some error cases and need to be
silently discarded.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If cxgb4_ofld_send() returns < 0, then send_fw_pass_open_req() must
free the request skb and the saved skb with the tcp header.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We cannot save the mapped length using the rdma max_page_list_len field
of the ib_fast_reg_page_list struct because the core code uses it. This
results in an incorrect unmap of the page list in c4iw_free_fastreg_pbl().
I found this with dma mapping debugging enabled in the kernel. The
fix is to save the length in the c4iw_fr_page_list struct.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Based on original work from Jay Hernandez <jay@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Always release the neigh entry in rx_pkt().
Based on original work by Santosh Rastapur <santosh@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
find_route() must treat loopback as a valid egress interface.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a four byte hole at the end of the "uresp" struct after the
->qid_mask member.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These sizes should be unsigned so we don't allow negative values and
have underflow bugs. These can come from the user so there may be
security implications, but I have not tested this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the IB core umem code and vendor drivers to use a
linear (chained) SG table instead of chunk list. With this change the
relevant code becomes clearer—no need for nested loops to build and
use umem.
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Building mem.o for 32 bits x86 triggers a GCC warning:
drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64. That's what _c4iw_write_mem_inline() already does.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function _c4iw_write_mem_dma() as static
because it is not used outside this file, which fixes the warning:
drivers/infiniband/hw/cxgb4/mem.c:176:5: warning: no previous prototype for ‘_c4iw_write_mem_dma’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Physical addresses may be wider than virtual addresses (e.g. on i386
with PAE) and must not be formatted with %p.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Lustre uses a advertised max MR size of ~0ULL to indicate it should
use a dma_mr. Hence advertise max MR size as ~0ULL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When polling, we do a GTS update if the accumulated cidx_inc == the CQ
depth / 16. However, if the CQ is large enough, Cq depth / 16 exceeds
the size of the field in the GTS word. So we also need to update if
cidx_inc hits CIDXINC_MASK to avoid overflowing the field.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
accept_cr() failed to set the arp error handler on a reused skb. This
results in a kernel crash if the arp does indeed time out.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When determining how many WRs are completed with a signaled CQE,
correctly deal with queue wraps.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch makes following fixes in QP flush logic:
- correctly flushes unsignaled WRs followed by a signaled WR
- supports for flushing a CQ bound to multiple QPs
- resets cidx_flush if a active queue starts getting HW CQEs again
- marks WQ in error when we leave RTS. This was only being done for
user queues, but we need it for kernel queues too so that
post_send/post_recv will start returning the appropriate error
synchronously
- eats unsignaled read resp CQEs. HW always inserts CQEs so we must
silently discard them if the read work request was unsignaled.
- handles QP flushes with pending SW CQEs. The flush and out of order
completion logic has a bug where if out of order completions are
flushed but not yet polled by the consumer and the qp is then
flushed then we end up inserting duplicate completions.
- c4iw_flush_sq() should only flush wrs that have not already been
flushed. Since we already track where in the SQ we've flushed via
sq.cidx_flush, just start at that point and flush any remaining.
This bug only caused a problem in the presence of unsignaled work
requests.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
[ Fixed sparse warning due to htonl/ntohl confusion. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move QP to TERMINATE instead to allow the peer to get the TERM
message. This bug wasn't detectable until newer FW that moves
connections out of RDMA mode as soon as an error is detected.
QP can exit RTS before the last AE arrives. This was introduced by
changes in the FW to kick connections out of RDMA mode as soon as an
error is detected. A side effect of this is that the driver can move
the QP out of RTS before the AE causing the connection to get kicked
out of RDMA mode is processed. Fix for this is to always post async
errors even if the QP is out of RTS.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add new cpl messages, cpl_act_open_req6 and cpl_t5_act_open_req6, for
initiating active open connections.
Use LLD api cxgb4_create_server and cxgb4_create_server6 for
initiating passive open connections. Similarly use cxgb4_remove_server
to remove the passive open connections in place of listen_stop.
Add support for iWARP over VLAN device and enable IPv6 support on VLAN device.
Make use of import_ep in c4iw_reconnect.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
[ Fix build when IPv6 is disabled and make sure iw_cxgb4 is not built-in
when ipv6 is a module. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify the type of local_addr and remote_addr fields in struct
iw_cm_id from struct sockaddr_in to struct sockaddr_storage to hold
IPv6 and IPv4 addresses uniformly.
Change the references of local_addr and remote_addr in cxgb4, cxgb3,
nes and amso drivers to match this. However to be able to actully run
traffic over IPv6, low-level drivers have to add code to support this.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
[ Fix unused variable warnings when INFINIBAND_NES_DEBUG not set.
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
"uresp.ma_sync_key" doesn't get set on this path so we leak 8 bytes of data.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1ojD
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
IB/iser: Add support for iser CM REQ additional info
IB/iser: Return error to upper layers on EAGAIN registration failures
IB/iser: Move informational messages from error to info level
IB/iser: Add module version
mlx4_core: Expose a few helpers to fill DMFS HW strucutures
mlx4_core: Directly expose fields of DMFS HW rule control segment
mlx4_core: Change a few DMFS fields names to match firmare spec
mlx4: Match DMFS promiscuous field names to firmware spec
mlx4_core: Move DMFS HW structs to common header file
IB/mlx4: Set link type for RAW PACKET QPs in the QP context
IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
RDMA/iwcm: Don't touch cmid after dropping reference
IB/qib: Correct qib_verbs_register_sysfs() error handling
IB/ipath: Correct ipath_verbs_register_sysfs() error handling
RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
SRPT: Fix odd use of WARN_ON()
IPoIB: Fix ipoib_hard_header() return value
RDMA: Rename random32() to prandom_u32()
RDMA/cxgb3: Fix uninitialized variable
...
Use preferable function name which implies using a pseudo-random number
generator.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use more preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Steve Wise <swise@chelsio.com>
Cc: linux-rdma@vger.kernel.org
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for TX lockup in IPoIB
- QLogic -> Intel update for qib driver
- Small static checker fix for qib
- Fix error path return value in cxgb4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABCAAGBQJRUH4BAAoJEENa44ZhAt0hP7gP/1SAVyeL8H/QNG6FDki7WUJC
qoW4bnezuNb35/H9NSPUQ/XA0QY2XKdJamkSnDJgE5WVjWZS80hKUBcdUi3S2GBl
Zbbs7H0Z2c/fiDvULrxRwqkZ/MlW4a6NnyKRHfSswKY+bAi+uybGoYGKmczXV4gC
LlscYagb4WYVTNVlD5JG9sxo5ChueAx51IbzuOWq/94iyKtocFB87ZyK2FhbQaua
n6af7lijAcTk02ad4JY2+ZZOOjGgOxP5+iigExzkXuS28dgNvNtN8FrrzLbiDHHy
aZ7miLSdPawO790nvXzn1NGL/nZiUmRI46d7qv6K/X38IX7GUFtMNEDUFCCZknwg
4VtNXzFExQy4YLCMpZ6di6rxMNVQ/EGj7QLN8jfD/pBEfiH/BMISdITL2KbgzcUv
5TUQGeQFzzyY+2HwUCqb0RCskbhsIUwLDpEnhnyHI2sZKbdRrpI07ZpL3iAhTcqK
5RDyXHNaVudVaKzaxq96vuw2OhH5fvACp3SdpaoCgZ54XuqoDoVW2q54vlj7anQI
E0/f+EDyBf8Nu5YydQri76HE+BqG+PzCqU5Rq9866itLEG2DMsmAj9KJJUcDTiCn
ANUIHoOpriGBAm1NP5tau/C0isvTw+lD/pBh26sdum1FwhoeqVf55PMvhxMG4Q/N
aC3g+RMj3BPkdhewWpY+
=SOee
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Small batch of InfiniBand/RDMA fixes for 3.9:
- Fix for TX lockup in IPoIB
- QLogic -> Intel update for qib driver
- Small static checker fix for qib
- Fix error path return value in cxgb4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: change QLogic to Intel
IB/ipath: Silence a static checker warning
IPoIB: Fix send lockup due to missed TX completion
RDMA/cxgb4: Fix error return code in create_qp()
Fix to return a negative error code from the error handling case
instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
TCPCT uses option-number 253, reserved for experimental use and should
not be used in production environments.
Further, TCPCT does not fully implement RFC 6013.
As a nice side-effect, removing TCPCT increases TCP's performance for
very short flows:
Doing an apache-benchmark with -c 100 -n 100000, sending HTTP-requests
for files of 1KB size.
before this patch:
average (among 7 runs) of 20845.5 Requests/Second
after:
average (among 7 runs) of 21403.6 Requests/Second
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neighbour table is full, dst_neigh_lookup/dst_neigh_lookup_skb will return
-ENOBUFS which is absolutely non zero, while all the code in kernel which use
above functions assume failure only on zero return which will cause panic. (for
example: : https://bugzilla.kernel.org/show_bug.cgi?id=54731).
This patch corrects above error with smallest changes to kernel source code and
also correct two return value check missing bugs in drivers/infiniband/hw/cxgb4/cm.c
Tested on my x86_64 SMP machine
Reported-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Tested-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T5 adapter does not support onchip queue memory. Present logic fails to
allocate QP for T5 and returns an error. Also, if module parameter ocqp_support
is zero then we are unable to allocate QP which should not be the case. Ideally
if ocqp_support parameter is 0 or onchip queue support is disable then host QP
should be allocated before returning an error.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always bump the tcam_full stat. Also, bump wr reply timeout to 30 seconds.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It enables direct DMA by HW to memory region PBL arrays and fast register PBL
arrays from host memory, vs the T4 way of passing these arrays in the WR itself.
The result is lower latency for memory registration, and larger PBL array
support for fast register operations.
This patch also updates ULP_TX_MEM_WRITE command fields for T5. Ordering bit of
ULP_TX_MEM_WRITE is at bit position 22 in T5 and at 23 in T4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both DB Flow-Control and DB Coalescing are disabled by default on T5
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for Chelsio T5 adapter.
Enables T5's Write Combining feature.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enhances the IB core support for Memory Windows (MWs).
MWs allow an application to have better/flexible control over remote
access to memory.
Two types of MWs are supported, with the second type having two flavors:
Type 1 - associated with PD only
Type 2A - associated with QPN only
Type 2B - associated with PD and QPN
Applications can allocate a MW once, and then repeatedly bind the MW
to different ranges in MRs that are associated to the same PD. Type 1
windows are bound through a verb, while type 2 windows are bound by
posting a work request.
The 32-bit memory key is composed of a 24-bit index and an 8-bit
key. The key is changed with each bind, thus allowing more control
over the peer's use of the memory key.
The changes introduced are the following:
* add memory window type enum and a corresponding parameter to ib_alloc_mw.
* type 2 memory window bind work request support.
* create a struct that contains the common part of the bind verb struct
ibv_mw_bind and the bind work request into a single struct.
* add the ib_inc_rkey helper function to advance the tag part of an rkey.
Consumer interface details:
* new device capability flags IB_DEVICE_MEM_WINDOW_TYPE_2A and
IB_DEVICE_MEM_WINDOW_TYPE_2B are added to indicate device support
for these features.
Devices can set either IB_DEVICE_MEM_WINDOW_TYPE_2A or
IB_DEVICE_MEM_WINDOW_TYPE_2B if it supports type 2A or type 2B
memory windows. It can set neither to indicate it doesn't support
type 2 windows at all.
* modify existing provides and consumers code to the new param of
ib_alloc_mw and the ib_mw_bind_info structure
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix compile warning about cast to pointer from integer of different size.
Signed-off-by: Stefan Hasko <hasko.stevo@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Work requests are passed between the host and the firmware with a
"cookie". This cookie is swapped to big-endian when passed to the
firmware and back to host endianness on return. This swapping seems
to be implemented incorrectly. Moreover, the byte swapping triggers
GCC warnings on 32 bit:
drivers/infiniband/hw/cxgb4/cm.c: In function ‘passive_ofld_conn_reply’:
drivers/infiniband/hw/cxgb4/cm.c:2803:12: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/infiniband/hw/cxgb4/cm.c: In function ‘send_fw_pass_open_req’:
drivers/infiniband/hw/cxgb4/cm.c:2941:16: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
[...]
But byte swapping isn't needed as the firmware doesn't actually touch
the cookie. Dropping byte swapping makes the warnings go away too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fixe the following types of sparse warnings
- cast to pointer from integer of different size
- cast from pointer to integer of different size
- incorrect type in assignment (different base types)
- incorrect type in argument 1 (different base types)
- cast from restricted __be64
- cast from restricted __be32
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
CPL_ABORT_REQ_RSS can come before TCP connection is established. In
such case peer_abort was trying to remove the hwtid, which was not
inserted. To avoid this we insert the hwtid when we are sure that we
are surely going to send passive accept request.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Don't wakeup threads blocked in rdma_init/rdma_fini if we are on
MPAv2, and want to retry connection with MPAv1.
Stop ep-timer on getting MPA version mismatch, before doing the
abort_connection - in process_mpa_request.
Take care to stop ep-timer in error paths for process_mpa_request.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Only reconnect if the endpoint wasn't freed.
peer_abort() should only attempt to reconnect if the endpoint wasn't
freed. Also remove hwtid from the debugfs idr.
Add missing check for peer2peer in MPAv2 code
Use correct mpa version on reject.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The endpoint timeout logic had a race that could cause an endpoint
object to be freed while it was still on the timedout list. This
can happen if the timer is stopped after it had fired, but before
the timedout thread processed the endpoint timeout.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
With newer firmware, we can get streaming data due to connection
errors before the driver moves the QP out of RTS.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Log AEs even if the QP isn't in RTS. It is useful information.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver is currently releasing the last ref on the QP too early.
This can cause bus errors due to HW still fetching WRs from the HW
queue. The fix is to keep a qp ref until we release the HW TID.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
With later firmware, the chances of getting streaming mode data after
we exit RTS is likely, so we don't need to warn for it. The only real
case where we don't expect it is when the QP is in RTS.
Move QP to ERROR when streaming mode data received.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If a FINI operation fails, then we need to ABORT instead of CLOSE.
Also, if we ABORT due to unexpected STREAMING data, then wake up
anybody blocked in FINI...
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This error means the RDMA connection was knocked out of RDMA mode,
probably due to an error on the connection.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Retries active opens for INUSE errors.
Logs any active ofld_connect_wr error replies.
Sends ofld_connect_wr on same ctrlq. It needs to go on the same control txq as
regular CPL active/passive messages.
Retries on active open replies with EADDRINUSE.
Uses active open fw wr only if active filter region is set.
Adds stat for ofld_connect_wr failures.
This patch also adds debugfs file to show endpoints.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It establishes passive open connection through firmware work request. Passive
open connection will go through this path as now instead of listening server we
create a server filter which will redirect the incoming SYN packet to the
offload queue. After this driver tries to establish the connection using
firmware work request.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It enables establishing active open connection using fw_ofld_connection work
request when cpl_act_open_rpl says TCAM full error which may be because
of LE hash collision. Current support is only for IPv4 active open connections.
Sets ntuple bits in active open requests. For T4 firmware greater than 1.4.10.0
ntuple bits are required to be set.
Adds nocong and enable_ecn module parameter options.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
[ Move all FW return values to t4fw_api.h. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression list es;
@@
-printk(
+WARN(1,
es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In the error path of registering memory when there's a failure to
allocate a chunk from the memory pool, we try to free the same chunk
we just failed to allocate, which will BUG().
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- mlx4 IB support for SR-IOV
- A couple of SRP initiator fixes
- Batch of nes hardware driver fixes
- Fix for long-standing use-after-free crash in IPoIB
- Other miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PAcy
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"First batch of InfiniBand/RDMA changes for the 3.7 merge window:
- mlx4 IB support for SR-IOV
- A couple of SRP initiator fixes
- Batch of nes hardware driver fixes
- Fix for long-standing use-after-free crash in IPoIB
- Other miscellaneous fixes"
This merge also removes a new use of __cancel_delayed_work(), and
replaces it with the regular cancel_delayed_work() that is now irq-safe
thanks to the workqueue updates.
That said, I suspect the sequence in question should probably use
"mod_delayed_work()". I just did the minimal "don't use deprecated
functions" fixup, though.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
IB/qib: Fix local access validation for user MRs
mlx4_core: Disable SENSE_PORT for multifunction devices
mlx4_core: Clean up enabling of SENSE_PORT for older (ConnectX-1/-2) HCAs
mlx4_core: Stash PCI ID driver_data in mlx4_priv structure
IB/srp: Avoid having aborted requests hang
IB/srp: Fix use-after-free in srp_reset_req()
IB/qib: Add a qib driver version
RDMA/nes: Fix compilation error when nes_debug is enabled
RDMA/nes: Print hardware resource type
RDMA/nes: Fix for crash when TX checksum offload is off
RDMA/nes: Cosmetic changes
RDMA/nes: Fix for incorrect MSS when TSO is on
RDMA/nes: Fix incorrect resolving of the loopback MAC address
mlx4_core: Fix crash on uninitialized priv->cmd.slave_sem
mlx4_core: Trivial cleanups to driver log messages
mlx4_core: Trivial readability fix: "0X30" -> "0x30"
IB/mlx4: Create paravirt contexts for VFs when master IB driver initializes
mlx4: Modify proxy/tunnel QP mechanism so that guests do no calculations
mlx4: Paravirtualize Node Guids for slaves
mlx4: Activate SR-IOV mode for IB
...
The variable ret is assigned return values in a couple of places, but
its value is never returned. This patch makes use of the ret variable
so that the caller get correct error codes returned.
The following changes are also introduced:
- The alloc_oc_sq function can return -ENOSYS or -ENOMEM so we want to
get the return value from it.
- Change the label names to improve readability.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
cxgb4 driver has duplicate definitions of registers which will be removed. This
patch updates the RDMA/cxgb4 driver accordingly.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Reviewed-by: Sivakumar Subramani <sivasu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparse correctly warns that if mpa->private_data_size is __be16, then
doing += on it is wrong, even if we do += htons(<something>) -- on a
little endian system, carries will go the wrong way. Fix this up by
doing the addition in native byte order.
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When using rping -c -a 0.0.0.0 with iw_cxgb4, the system crashes when
rdma_connect() is called. ip_dev_find() will return NULL, but pdev is
accessed anyway.
Checking that pdev is NULL and returning -ENODEV prevents the system
from crashing.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This allows querying the QP state before flushing.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Using kfifos for ID management was limiting the number of QPs and
preventing NP384 MPI jobs. So replace it with a simple bitmap
allocator.
Remove IDs from the IDR tables before deallocating them. This bug was
causing the BUG_ON() in insert_handle() to fire because the ID was
getting reused before being removed from the IDR table.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This allows dumping thousands of QPs. Log active open failures of
interest.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
