The semantics of the old tile __write_once are the same as the
newer generic __ro_after_init, so rename them all and get rid
of the tile-specific version.
This does not enable actual support for __ro_after_init,
which had been dropped from the tile architecture before the
initial upstreaming was done, since we had at that time switched
to using 16MB huge pages to map the kernel.
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And other message logging neatening.
Other miscellanea:
o coalesce formats
o realign arguments
o standardize a couple of macros
o use __func__ instead of embedding the function name
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
cold is a bool, make it one. Make the likely case the "if" part of the
block instead of the else as according to the optimisation manual this is
preferred.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This chip is no longer being actively developed for (it was superceded
by the TILEPro64 in 2008), and in any case the existing compiler and
toolchain in the community do not support it. It's unlikely that the
kernel works with TILE64 at this point as the configuration has not been
tested in years. The support is also awkward as it requires maintaining
a significant number of ifdefs. So, just remove it altogether.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We use virt_to_pte(NULL, va) a lot, which isn't very obvious.
I added virt_to_kpte(va) as a more obvious wrapper function,
that also validates the va as being a kernel adddress.
And, I fixed the semantics of virt_to_pte() so that we handle
the pud and pmd the same way, and we now document the fact that
we handle the final pte level differently.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds support for CONFIG_PREEMPT (full kernel preemption).
In addition to the core support, this change includes a number
of places where we fix up uses of smp_processor_id() and per-cpu
variables. I also eliminate the PAGE_HOME_HERE and PAGE_HOME_UNKNOWN
values for page homing, as it turns out they weren't being used.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This was shown up by running with "allmodconfig". I used
EXPORT_SYMBOL() to match existing conventions in files that
were already exporting symbols, or that were exported that way
by other architectures, and otherwise EXPORT_SYMBOL_GPL().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The tilegx PCI root complex support (currently only in linux-next)
is limited to pages that are homed on cached in the default manner,
i.e. "hash-for-home". This change supports delivery of I/O data to
pages that are cached in other ways (locally on a particular core,
uncached, user-managed incoherent, etc.).
A large part of the change is supporting flushing pages from cache
on particular homes so that we can transition the data that we are
delivering to or from the device appropriately. The new homecache_finv*
routines handle this.
Some changes to page_table_range_init() were also required to make
the fixmap code work correctly on tilegx; it hadn't been used there
before.
We also remove some stub mark_caches_evicted_*() routines that
were just no-ops anyway.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds support for a new "super" bit in the PTE, using the new
arch_make_huge_pte() method. The Tilera hypervisor sees the bit set at a
given level of the page table and gangs together 4, 16, or 64 consecutive
pages from that level of the hierarchy to create a larger TLB entry.
One extra "super" page size can be specified at each of the three levels
of the page table hierarchy on tilegx, using the "hugepagesz" argument
on the boot command line. A new hypervisor API is added to allow Linux
to tell the hypervisor how many PTEs to gang together at each level of
the page table.
To allow pre-allocating huge pages larger than the buddy allocator can
handle, this change modifies the Tilera bootmem support to put all of
memory on tilegx platforms into bootmem.
As part of this change I eliminate the vestigial CONFIG_HIGHPTE support,
which never worked anyway, and eliminate the hv_page_size() API in favor
of the standard vma_kernel_pagesize() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
When freeing the page with this API, the page was "put" twice.
This was only discovered bringing up an MPT fusion controller, which
actually used the API; it hadn't been invoked previously, so the bug
had gone unnoticed.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The Tilera architecture traditionally supports 64KB page sizes
to improve TLB utilization and improve performance when the
hardware is being used primarily to run a single application.
For more generic server scenarios, it can be beneficial to run
with 4KB page sizes, so this commit allows that to be specified
(by modifying the arch/tile/include/hv/pagesize.h header).
As part of this change, we also re-worked the PTE management
slightly so that PTE writes all go through a __set_pte() function
where we can do some additional validation. The set_pte_order()
function was eliminated since the "order" argument wasn't being used.
One bug uncovered was in the PCI DMA code, which wasn't properly
flushing the specified range. This was benign with 64KB pages,
but with 4KB pages we were getting some larger flushes wrong.
The per-cpu memory reservation code also needed updating to
conform with the newer percpu stuff; before it always chose 64KB,
and that was always correct, but with 4KB granularity we now have
to pay closer attention and reserve the amount of memory that will
be requested when the percpu code starts allocating.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It now takes an additional argument so it can be used to
flush-and-invalidate pages that are cached using hash-for-home
as well those that are cached with coherence point on a single cpu.
This allows it to be used more widely for changing the coherence
point of arbitrary pages when necessary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds one of the Tilera standard <arch> headers to the set
of headers shipped with Linux. The <arch/sim.h> header provides
methods for programmatically interacting with the Tilera simulator.
The current <arch/sim.h> provides inline assembly for the _sim_syscall
function, so the declaration and definition previously provided
manually in Linux are no longer needed. We now use the standard
sim_validate_lines_evicted() method from <arch/sim.h> rather than
rolling our own direct call to sim_syscall().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change rolls up random cleanups not representing any actual bugs.
- Remove a stale CONFIG_ value from the default tile_defconfig
- Remove unused tns_atomic_xxx() family of methods from <asm/atomic.h>
- Optimize get_order() using Tile's "clz" instruction
- Fix a bad hypervisor upcall name (not currently used in Linux anyway)
- Use __copy_in_user_inatomic() name for consistency, and export it
- Export some additional hypervisor driver I/O upcalls and some homecache calls
- Remove the obfuscating MEMCPY_TEST_WH64 support code
- Other stray comment cleanups, #if 0 removal, etc.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This commit is primarily changes caused by reviewing "sparse"
and "checkpatch" output on our sources, so is somewhat noisy, since
things like "printk() -> pr_err()" (or whatever) throughout the
codebase tend to get tedious to read. Rather than trying to tease
apart precisely which things changed due to which type of code
review, this commit includes various cleanups in the code:
- sparse: Add declarations in headers for globals.
- sparse: Fix __user annotations.
- sparse: Using gfp_t consistently instead of int.
- sparse: removing functions not actually used.
- checkpatch: Clean up printk() warnings by using pr_info(), etc.;
also avoid partial-line printks except in bootup code.
- checkpatch: Use exposed structs rather than typedefs.
- checkpatch: Change some C99 comments to C89 comments.
In addition, a couple of minor other changes are rolled in
to this commit:
- Add support for a "raise" instruction to cause SIGFPE, etc., to be raised.
- Remove some compat code that is unnecessary when we fully eliminate
some of the deprecated syscalls from the generic syscall ABI.
- Update the tile_defconfig to reflect current config contents.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.
This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
