Commit 36387a2b1f ("k3dma: Fix
memory handling in preparation for cyclic mode") adds few
calls to ON_WARN_ONCE() to track the use of ds_run/ds_done.
After the two fixes:
- dmaengine: k3dma: fix non-cyclic mode
- dmaengine: k3dma: fix re-free of the same descriptor
the behaviour of ds_run/ds_done is properly fixed.
The remaining ON_WARN_ONCE() are never triggered and can be
removed.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 36387a2b1f ("k3dma: Fix
memory handling in preparation for cyclic mode") adds code
to free the descriptor in ds_done.
In cyclic mode, ds_done is never used and it's always NULL,
so the added code is not executed.
In non-cyclic mode, ds_done is used as a flag: when not NULL
it signals that the descriptor has been consumed. No need to
free it because it would be free by vchan_complete().
The fix takes back the code changed by the commit above:
- remove the free on the descriptor;
- initialize ds_done to NULL for the next run.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 36387a2b1f ("k3dma: Fix
memory handling in preparation for cyclic mode") broke the
logic around ds_run/ds_done in case of non-cyclic DMA.
This went unnoticed as the only user of k3dma was the i2s
audio driver but, with a patch set to enable dma on SPI, the
issue popped out.
The fix re-applies the initialization to ds_run/ds_done in
k3_dma_start_txd() that were removed by the commit above.
Also, one of the calls to k3_dma_start_txd() is triggered by
(ds_done != NULL), so remove the noisy and useless call to
WARN_ON_ONCE().
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We observed performance increase with DMA copy from memory
to MMIO by changing the interrupt coalescing value to 0.
The previous set value was projected on the C5xxx Xeon
platform and no longer holds true. Removing hard coded
value and providing a tune-able in sysfs in order to allow
user to tune this on a per channel basis. By default this
value will be set to 0.
Example of sysfs variable importing for interrupt coalescing
value from command line:
echo 5> /sys/devices/pci0000:00/0000:00:04.0/dma/dma0chan0/
quickdata/intr_coalesce
Reported-by: Nithin Sujir <nsujir@tintri.com>
Signed-off-by: Ujjal Singh <ujjal.singh@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c678fa66341c: ("dmaengine: remove DMA_SG as it is dead code in
kernel") removes DMA_SG from dmaengine subsystem but missed removing unused
xgene_dma_invalidate_buffer function, so remove it
drivers/dma/xgene-dma.c:394:13: warning: ‘xgene_dma_invalidate_buffer’ defined but not used [-Wunused-function]
static void xgene_dma_invalidate_buffer(__le64 *ext8)
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c678fa66341c: ("dmaengine: remove DMA_SG as it is dead code in
kernel") removes DMA_SG from dmaengine subsystem but missed the newly added
driver, so remove it from here as well
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are no in kernel consumers for DMA_SG op. Removing operation,
dead code, and test code in dmatest.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace '%d' by '%zu' to fix the compilation warning:-
"format ‘%d’ expects argument of type ‘int’,but argument has type ‘size_t’ [-Wformat=]"
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If device_node np doesn't contain child or first child doesn't have
property "reg" then hidma_mgmt_of_populate_channels() perfoms
deallocation on uninitialized local variable res.
The patch adds res initialization by NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would then
call request_irq(0, ...) in tegra_adma_alloc_chan_resources() and never get
valid channel interrupt.
Check for 'tdc->irq <= 0' instead and return -ENXIO from the driver's probe
iff of_irq_get() returned 0.
Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It's better to be explicit and use the DRIVER_ATTR_RW() and
DRIVER_ATTR_RO() macros when defining a driver's sysfs file.
Bonus is this fixes up a checkpatch.pl warning.
This is part of a series to drop DRIVER_ATTR() from the tree entirely.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver builds with warnings which can be fixed by making these
functions static.
CC [M] drivers/dma/bcm-sba-raid.o
drivers/dma/bcm-sba-raid.c:786:1: warning: no previous prototype for ‘sba_prep_dma_xor_req’ [-Wmissing-prototypes]
sba_prep_dma_xor_req(struct sba_device *sba,
^
drivers/dma/bcm-sba-raid.c:995:1: warning: no previous prototype for ‘sba_prep_dma_pq_req’ [-Wmissing-prototypes]
sba_prep_dma_pq_req(struct sba_device *sba, dma_addr_t off,
^
drivers/dma/bcm-sba-raid.c:1247:1: warning: no previous prototype for ‘sba_prep_dma_pq_single_req’ [-Wmissing-prototypes]
sba_prep_dma_pq_single_req(struct sba_device *sba, dma_addr_t off,
^
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A regression was found while testing QOS with different channels.
The QOS register offset is 0x700 rather than 0x300.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A false overriding information is being presented during boot
under this scenario.
1. First object checks for kernel command line value against zero.
2. It doesn't find it, it sets the command line variable to the
value coming from ACPI/DT.
3. Second object is being probed.
4. Second object sees that the value of kernel command line
override is non-zero, it prints an overriding message even though
value matches ACPI/DT value.
hidma-mgmt QCOM8060:03: overriding max-write-burst-bytes: 1024
Add an additional check to verify that kernel command line value
is different from the ACPI/DT value.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
HIDMA HW supports memset operation in addition to memcpy.
Since the memset API is present on the kernel now, bring the
memset feature into life.
The descriptor format is the same for both memcpy and memset.
Type of the descriptor is 4 when memset is requested.
The lowest 8 bits of the source DMA argument is used as a
fill pattern.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver adds support for the Altera / Intel modular Scatter-Gather
Direct Memory Access (mSGDMA) intellectual property (IP) to the Linux
DMAengine subsystem. Currently it supports the following op modes:
- DMA_MEMCPY
- DMA_SG
- DMA_SLAVE
This implementation has been tested on an Altera Cyclone FPGA connected
via PCIe, both on an ARM and an x86 platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Introducing memset test into dmatest. This change allows us to test
memset capable HW using the dmatest test procedure. The new dmatest
value for memset is 2 and it is not the default value.
Memset support patch shares the same code path as the other dmatest
code to reuse as much as we can.
The first value inside the source buffer is used as a pattern
to fill in the destination buffer space.
Prior to running the test, source/destination buffers are initialized
in the current code.
"The remaining bits are the inverse of a counter which increments by
one for each byte address."
Memset test will fill in the upper bits of pattern with the inverse of
fixed counter value 1 as opposed to an incrementing value in a loop.
An example run is as follows:
echo dma0chan0 > /sys/module/dmatest/parameters/channel
echo 2 > /sys/module/dmatest/parameters/dmatest
echo 2000 > /sys/module/dmatest/parameters/timeout
echo 10 > /sys/module/dmatest/parameters/iterations
echo 1 > /sys/module/dmatest/parameters/run
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12582 3056 16 15654 3d26 drivers/dma/ioat/init.o
File size After adding 'const':
text data bss dec hex filename
14773 865 16 15654 3d26 drivers/dma/ioat/init.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=srPZ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
* tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: qcom_hidma: correct API violation for submit
dmaengine: zynqmp_dma: Remove max len check in zynqmp_dma_prep_memcpy
dmaengine: tegra-apb: Really fix runtime-pm usage
dmaengine: fsl_raid: make of_device_ids const.
dmaengine: qcom_hidma: allow ACPI/DT parameters to be overridden
dmaengine: fsldma: set BWC, DAHTS and SAHTS values correctly
dmaengine: Kconfig: Simplify the help text for MXS_DMA
dmaengine: pl330: Delete unused functions
dmaengine: Replace WARN_TAINT_ONCE() with pr_warn_once()
dmaengine: Kconfig: Extend the dependency for MXS_DMA
dmaengine: mxs: Use %zu for printing a size_t variable
dmaengine: ste_dma40: Cleanup scatterlist layering violations
dmaengine: imx-dma: cleanup scatterlist layering violations
dmaengine: use proper name for the R-Car SoC
dmaengine: imx-sdma: Fix compilation warning.
dmaengine: imx-sdma: Handle return value of clk_prepare_enable
dmaengine: pl330: Add IOMMU support to slave tranfers
dmaengine: DW DMAC: Handle return value of clk_prepare_enable
dmaengine: pl08x: use GENMASK() to create bitmasks
dmaengine: pl08x: Add support for Faraday Technology FTDMAC020
...
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----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=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
Current code is violating the DMA Engine API by putting the submitted
requests directly into the HW queue. This causes queued transactions
to be started by another thread as soon as the first one finishes.
The DMA Engine document clearly states this.
"dmaengine_submit() will not start the DMA operation".
Move HW queuing of the requests into the issue_pending() routine
to comply with API requirements also create a new queued state for
temporarily holding the requests.
A descriptor goes through these transitions now.
free->prepared->queued->active->completed->free
as opposed to
free->prepared->active->completed->free
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove check for "len > ZYNQMP_DMA_MAX_TRANS_LEN" as its not needed.
If the length is larger, the transfer is split up into multiple parts
with the max descriptor length already.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit edd3bdbe9d ("dmaengine: tegra-apb: Correct runtime-pm usage")
added pm_runtime_get/put() calls to the tegra-apb DMA system suspend
callbacks. Runtime PM is disabled during system suspend and so these
APIs cannot be used. Fix the suspend handling for the tegra-apb DMA by
moving the save and restore of the DMA register context into the
runtime PM suspend and resume callbacks, and then use the
pm_runtime_force_suspend/resume() APIs to invoke the runtime PM
callbacks during system suspend.
Fixes: edd3bdbe9d ("dmaengine: tegra-apb: Correct runtime-pm usage")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3981 608 0 4589 11ed drivers/dma/fsl_raid.o
File size after constify:
text data bss dec hex filename
4381 192 0 4573 11dd drivers/dma/fsl_raid.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Parameters like maximum read/write request size and the maximum
number of active transactions are currently configured in DT/ACPI.
This patch allows a user to override these to fine tune performance
for their application.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bits of BWC, DAHTS and SAHTS in the DMA mode register must be cleared
before a new value can be or-ed in.
Signed-off-by: Thomas Breitung <thomas.breitung@izt-labs.de>
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA_ERROR_CODE is not a public API and will go away. Instead properly
unwind based on the loop counter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
When the port_window support was verified it was done on setup where only
the MEM_TO_DEV direction was enabled. This got un-noticed and thus only
this direction worked.
Now that I have managed to get a setup to verify both direction it turned
out that the setup was incorrect:
omap_desc members are settings for the slave port while the omap_sg members
apply to the memory side of the sDMA setup.
Fixes: 527a275913 ("dmaengine: omap-dma: Fix the port_window support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: dmaengine@vger.kernel.org
Cc: dan.j.williams@intel.com
Cc: vinod.koul@intel.com
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the help text for the MXS_DMA option is incomplete as it does
not mention MX6SX, MX6ULL and MX7D, for example.
Instead of extending this list everytime a new SoC comes out, let's
keep the text more generic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The WARN_TAINT_ONCE() prints out a loud stack trace on broken BIOSes.
The systems that have this problem are several years out of support and
no longer have BIOS updates available. The stack trace isn't necessary
and a pr_warn_once() will do.
Change WARN_TAINT_ONCE() to pr_warn_once() and taint.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Duyck, Alexander H <alexander.h.duyck@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently it is not possible to select the mxs dma driver when only
mx6sx or mx7 are selected.
Extend the dependency to allow the mxs dma driver to be built whenever
ARCH_MXS or ARCH_MXC is selected.
This has the benefit to avoid having to add new entries in the
MXS_DMA Kconfig everytime a new i.MX SoC shows up and it also makes
it consistent with the other i.MX DMA engines, such as IMX_DMA and
IMX_SDMA.
While at it, also pass COMPILE_TEST for increasing the build coverage.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use %zu for printing a size_t variable in order to fix the following
build warning:
drivers/dma/mxs-dma.c: In function 'mxs_dma_prep_dma_cyclic':
drivers/dma/mxs-dma.c:621:5: warning: format '%d' expects argument of type 'int', but argument 3 has type 'size_t' [-Wformat]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When removing a device with less than 9 IRQs (AMBA_NR_IRQS), we'll get a
big WARN_ON from devres.c because pl330_remove calls devm_free_irqs for
unallocated irqs. Similarly to pl330_probe, check that IRQ number is
present before calling devm_free_irq.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This dma engine driver directly accesses page_link assuming knowledge
that should be contained only in scatterlist.h.
We replace this access with a call to sg_chain which is equivalent.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Per Förlin <per.forlin@axis.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This dma engine driver directly accesses page_link assuming knowledge
that should be contained only in scatterlist.h.
We replace these with calls to sg_chain and sg_assign_page.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Per Förlin <per.forlin@axis.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace '%d' by '%zu' to fix the following compilation warning:-
drivers/dma/imx-sdma.c: In function ‘sdma_prep_dma_cyclic’:
drivers/dma/imx-sdma.c:1327:5: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat=]
channel, period_len, 0xffff);
^
drivers/dma/imx-sdma.c:1350:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 5 has type ‘size_t’ [-Wformat=]
dev_dbg(sdma->dev, "entry %d: count: %d dma: %#llx %s%s\n",
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In descriptor mode, the descriptor running pointer is not maintained
by the interrupt handler, thus, driver finds the running descriptor
from the descriptor pointer field in the CHCRB register.
But, CHCRB::DPTR indicates *next* descriptor pointer, not current.
Thus, The residue calculation will be missed. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Wire up dma_map_resource() for slave transfers, so that we can let the
PL330 use IOMMU-backed DMA mapping ops on systems with an appropriate
IOMMU and RAM above 4GB, to avoid CPU bounce buffering.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current buffer is being reset to zero on device_free_chan_resources()
but not on device_terminate_all(). It could happen that HW is restarted and
expects BASE0 to be used, but the driver is not synchronized and will start
from BASE1. One solution is to reset the buffer explicitly in
m2p_hw_setup().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After reading the specs for the Faraday Technology FTDMAC020 found
in the Gemini platform, it becomes pretty evident that this is just
another PL08x derivative, and should be handled like such by simply
extending the existing PL08x driver to handle the quirks in this
hardware.
This patch makes memcpy work and has been tested on the Gemini and
also regression-tested on the Nomadik NHK15 using dmatest with
10 threads per channel without a hinch for hours.
I have not implemented slave DMA in those codepaths, because this
device (Gemini) does not use slave DMA, and it seems like devices
using FTDMAC020 for device DMA have a slightly different register
layout so some real hardware is needed to proceed with this. I
left some FIXME etc in the code for this.
I had to do some refactorings of some helper functions, but I have
not split those into separate patches because these refactorings
do not make much sense without the increased complexity of handling
the FTDMAC020.
The DMA test would hang the platform on me on the Gemini after a
few thousand iterations, however after turning of the caches the
problem immediately disappeared and I could run the DMA engine
with 10 threads pers physical channel for days in a row without
a crash. I think there is no problem with the DMA driver: instead
it is something fishy in the FA526 cache handling code that get
pretty heavily exercised by the DMA engine and we need to go and
fix that instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the vendor data does not specify any signals, we do not
have to support slave DMA. Make the registration of the slave
DMA engine optional, so we can use this for the FTDMAC020
in the Gemini that only has memcpy support.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We cannot use bits from configuration registers as API between
platforms and driver like this, abstract it out to two enums
and mimic the stuff passed as device tree data.
This is done to make it possible for the driver to generate the
ccfg word on-the-fly so we can support more PL08x derivatives.
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes a race condition where the channel resources could be freed
before the ISR had finished running resulting in a NULL pointer
reference from the ISR.
[ 167.148934] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 167.157051] pgd = ffff80003c641000
[ 167.160449] [00000000] *pgd=000000007c507003, *pud=000000007c4ff003, *pmd=0000000000000000
[ 167.168719] Internal error: Oops: 96000046 [#1] PREEMPT SMP
[ 167.174289] Modules linked in:
[ 167.177348] CPU: 3 PID: 10547 Comm: dma_ioctl Not tainted 4.11.0-rc1-00001-g8d92afddc2f6633a #73
[ 167.186131] Hardware name: Renesas Salvator-X board based on r8a7795 (DT)
[ 167.192917] task: ffff80003a411a00 task.stack: ffff80003bcd4000
[ 167.198850] PC is at rcar_dmac_chan_prep_sg+0xe0/0x400
[ 167.203985] LR is at rcar_dmac_chan_prep_sg+0x48/0x400
Based of previous work by:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Implement the device_synchronize() callback which wait until a dma
channel is stopped to provide a synchronization point.
This protects the driver from multiple race conditions when terminating
and freeing resources. E.g. the completion callback still running after
device_terminate_all() has completed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IRQ number is needed after probe to be able to add synchronisation
points in other places in the driver when freeing resources and to
implement a device_synchronize() callback. Store the IRQ number in the
struct rcar_dmac_chan so that it can be used later.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Req is never null on at the point of the null check, so
remove this redundant check and just return &req->tx.
Detected by CoverityScan, CID#1436147 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new driver requires both mailbox and raid support for compile
testing:
drivers/dma/built-in.o: In function `sba_remove':
edma.c:(.text+0x4414): undefined reference to `mbox_free_channel'
drivers/dma/built-in.o: In function `sba_issue_pending':
edma.c:(.text+0x46cc): undefined reference to `mbox_send_message'
drivers/dma/built-in.o: In function `sba_probe':
edma.c:(.text+0x4e60): undefined reference to `mbox_request_channel'
edma.c:(.text+0x5038): undefined reference to `mbox_free_channel'
drivers/dma/built-in.o: In function `sba_tx_status':
edma.c:(.text+0x5210): undefined reference to `mbox_client_peek_data'
drivers/dma/built-in.o: In function `sba_prep_dma_pq_req':
edma.c:(.text+0x5784): undefined reference to `raid6_gflog'
edma.c:(.text+0x5798): undefined reference to `raid6_gflog'
This rearranges the Kconfig dependencies accordingly.
Fixes: 743e1c8ffe ("dmaengine: Add Broadcom SBA RAID driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Broadcom stream buffer accelerator (SBA) provides offloading
capabilities for RAID operations. This SBA offload engine is
accessible via Broadcom SoC specific ring manager.
This patch adds Broadcom SBA RAID driver which provides one
DMA device with RAID capabilities using one or more Broadcom
SoC specific ring manager channels. The SBA RAID driver in its
current shape implements memcpy, xor, and pq operations.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds the support for suspend/resume in the mv_xor_v2
driver. The suspend suspend function disables the XOR engine after the
DMA stack has handled all pending descriptors in the queue. The resume
function re-configures the XOR engine and re-enables the engine.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove unnecessary write to DESQ_STOP register, this register is used to
enable or disable the XOR engine, and not to issue all pending
descriptors in the queue. mv_xor_v2 driver already writes to this
register and enable XOR engine in the mv_xor_v2_descq_init() function,
called during initialization.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Until now, the driver was not using interrupt coalescing: one interrupt
was generated for each descriptor processed by the XOR engine. This
commit changes that by using the interrupt coalescing features of the
hardware, by setting both a number of descriptors processed before an
interrupt is generated and a timeout before an interrupt is generated.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XORv2 engine on Armada 7K/8K can only access the first 40 bits of
the physical address space, so the DMA mask must be set accordingly.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current implementation of interrupt coalescing doesn't work, because
it doesn't configure the coalescing timer, which is needed to make sure
we get an interrupt at some point.
As a fix for stable, we simply remove the interrupt coalescing
functionality. It will be re-introduced properly in a future commit.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mv_xor_v2_tx_submit() gets the next available HW descriptor by
calling mv_xor_v2_get_desq_write_ptr(), which reads a HW register
telling the next available HW descriptor. This was working fine when HW
descriptors were issued for processing directly in tx_submit().
However, as part of the review process of the driver, a change was
requested to move the actual kick-off of HW descriptors processing to
->issue_pending(). Due to this, reading the HW register to know the next
available HW descriptor no longer works.
So instead of using this HW register, we implemented a software index
pointing to the next available HW descriptor.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The engine was enabled prior to its configuration, which isn't
correct. This patch relocates the activation of the XOR engine, to be
after the configuration of the XOR engine.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Descriptors that have not been acknowledged by the async_tx layer
should not be re-used, so this commit adjusts the implementation of
mv_xor_v2_prep_sw_desc() to skip descriptors for which
async_tx_test_ack() is false.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mv_xor_v2_tasklet() is looping over completed HW descriptors. Before the
loop, it initializes 'next_pending_hw_desc' to the first HW descriptor
to handle, and then the loop simply increments this point, without
taking care of wrapping when we reach the last HW descriptor. The
'pending_ptr' index was being wrapped back to 0 at the end, but it
wasn't used in each iteration of the loop to calculate
next_pending_hw_desc.
This commit fixes that, and makes next_pending_hw_desc a variable local
to the loop itself.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mv_xor_v2_prep_sw_desc() is called from a few different places in
the driver, but we never take into account the fact that it might
return NULL. This commit fixes that, ensuring that we don't panic if
there are no more descriptors available.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor, ioat,
dmatest
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ygkn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor,
ioat, dmatest"
* tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (35 commits)
dmaengine: pl08x: remove lock documentation
dmaengine: pl08x: fix pl08x_dma_chan_state documentation
dmaengine: pl08x: Use the BIT() macro consistently
dmaengine: pl080: Fix some missing kerneldoc
dmaengine: pl080: Cut some unused defines
dmaengine: dmatest: Add check for supported buffer count (sg_buffers)
dmaengine: dmatest: Select DMA_ENGINE_RAID as its needed for the slave_sg test
dmaengine: virt-dma: Convert to use list_for_each_entry_safe()
dma-debug: use offset_in_page() macro
dmaengine: mv_xor: use offset_in_page() macro
dmaengine: dmatest: use offset_in_page() macro
dmaengine: sun4i: fix invalid argument
dmaengine: ioat: use setup_timer
dmaengine: cppi41: Fix an Oops happening in cppi41_dma_probe()
dmaengine: pl330: remove pdata based initialization
dmaengine: cppi: fix build error due to bad variable
dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
dmaengine: cppi41: use managed functions devm_*()
dmaengine: cppi41: fix cppi41_dma_tx_status() logic
dmaengine: qcom_hidma: pause the channel on shutdown
...
This makes the driver shift bits with BIT() which is used on other
places in the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Two elements of the physical channel description was missing.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using dmatest with sg_buffers=128 I stumbled upon the problem, that
the "map_cnt" variable of "struct dmaengine_unmap_data" was set to 0.
"map_cnt" is an "u8" variable, resulting in an overrun when its
value is set to src_cnt + dst_cnt, to twice the sg_buffer value.
This patch adds a small check to dmatest, so that this confusing error
is detected and the test is aborted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To enable usage of multiple SG buffers via the sg_buffers= module
parameter, lets select DMA_ENGINE_RAID via Kconfig when DMATEST is
configured. Otherwise the dmatest will "BUG" when more than 1
buffer (total of 2 for src + dst) is configured via sg_buffers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use list_for_each_entry_safe() instead of open coding variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The "pchans_used" field is an unsigned long array.
for_each_clear_bit_from() expects an unsigned long pointer,
not an array address.
$ make C=2 drivers/dma/sun4i-dma.o
CHECK drivers/dma/sun4i-dma.c
drivers/dma/sun4i-dma.c:241:9: warning: incorrect type in argument 1 (different base types)
drivers/dma/sun4i-dma.c:241:9: expected unsigned long const *p
drivers/dma/sun4i-dma.c:241:9: got unsigned long ( *<noident> )[1]
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fix an Oops happening on all platforms using the old dt bindings
(all platforms but da8xx).
This update cppi41_dma_probe() to use the index variable which is
required to keep compatibility between old and new dt bindings.
Fixes: 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver is now used only on platforms which support device tree, so
it is safe to remove legacy platform data based initialization code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
For plat-samsung:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
moved the code to devm_* but erranously changed a varible name, so fix it.
drivers/dma/cppi41.c:1052:5: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
cdd->qmrg_mem = devm_ioremap_resource(dev, mem);
^
drivers/dma/cppi41.c:1053:16: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
if (IS_ERR(cdd->qmrg_mem))
^
drivers/dma/cppi41.c:1054:21: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
return PTR_ERR(cdd->qmrg_mem);
^
Fixes: 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
sdma_disable_channel() cannot ensure dma is stopped to access
module's FIFOs. There is chance SDMA core is running and accessing
BD when disable of corresponding channel, this may cause sometimes
even after call of .sdma_disable_channel(), SDMA core still be
running and accessing module's FIFOs.
According to NXP R&D team a delay of one BD SDMA cost time (maximum
is 1ms) should be added after disable of the channel bit, to ensure
SDMA core has really been stopped after SDMA clients call
.device_terminate_all.
This patch introduces adds a new function sdma_disable_channel_with_delay()
which simply adds 1ms delay after call sdma_disable_channel(),
and set it as .device_terminate_all.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This makes the error handling much more simpler than open-coding
everything and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It makes sense to set residue when channel is in progress. Otherwise it
should be 0 since transfer is completed. Meanwhile this patch doesn't
prevent to set residue value anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need to ensure that all DMAs and interrupts are cleared during
shutdown operation in order for kexec to start the next kernel clearly.
Otherwise, HW could be performing a DMA into random addresses in the
middle of second kernel start.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Once the channels are stopped, disable interrupts to make sure no new
HW interaction can happen.
Similarly, re-enable the interrupts only if we know that channel is
operational again.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
SYS-DMAC can use 40bit address transfer, and it supports Descriptor
Mode too. Current SYS-DMAC driver disables Descriptor Mode if it was
40bit address today. But it can use Descriptor Mode with 40bit if
transfer Source/Destination address are located in same 4GiB region
in the 40 bit address space.
This patch enables it if all condition was clear
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device_prep_dma_memcpy() callback for this driver allocates a new
xilinx_dma_tx_descriptor whose TX segments list is initialized as empty,
but then gets invalid TX segment pointer by list_last_entry() from the
empty TX segments list and memory corruption happens by the attempt to
update the next descriptor in invalid TX segment pointer.
This removes unnecessary memory access for nonexistent tail TX segment
which causes memory corruption.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device_terminate_all() callback for this driver stops current DMA
operations by clearing RUNSTOP bit in the control register and waiting
HALTED bit set in the status register.
But AXI CDMA which is one of the supported DMA engine by this driver
does not provide the run / stop controls and those bits in the control
and status registers are reserved. So when device_terminate_all() is
called, the error message is printed and the channel is marked as having
errors in xilinx_dma_halt().
This change adds stop_transfer() callback which differentiates CDMA and
other DMA engine. The CDMA's one avoids the unsupported operations and
instead polls the status register to check if the DMA operations are in
progress for AXI CDMA.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes the following warning when building with clang and
CONFIG_DMA_ENGINE_RAID=n :
drivers/dma/dmaengine.c:1102:11: error: array index 2 is past the end of the array (which contains 1 element) [-Werror,-Warray-bounds]
return &unmap_pool[2];
^ ~
drivers/dma/dmaengine.c:1083:1: note: array 'unmap_pool' declared here
static struct dmaengine_unmap_pool unmap_pool[] = {
^
drivers/dma/dmaengine.c:1104:11: error: array index 3 is past the end of the array (which contains 1 element) [-Werror,-Warray-bounds]
return &unmap_pool[3];
^ ~
drivers/dma/dmaengine.c:1083:1: note: array 'unmap_pool' declared here
static struct dmaengine_unmap_pool unmap_pool[] = {
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The SDMA hardware/driver does not actually report the transfer residue at
burst size granularity, but in fact is only able to report residue after
each finished segment.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The check to see if cd is null is redundant, pdata->channels is
never null at this point, and hence &pdata->channels[i] cannot
be null, so remove the null check.
Detected by CoverityScan, CID#1357194 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During the teardown of a RX channel, because there is only one
completion queue available for RX channel, descriptor of another
channel may be popped which will cause 2 warnings:
- the first one because we popped a wrong descriptor
(neither the channel's descriptor, nor the teardown descriptor).
- the second one happen during the teardown of another channel,
because we can't find the channel descriptor
(that is, the one that caused the first warning).
To avoid that, use one free queue instead of a transmit completion queue.
Note that fix doesn't fix all the teardown warnings:
I still get some when I run some corner case.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DA8xx has a CPPI 4.1 DMA controller.
This is add the glue layer required to make it work on DA8xx.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All the platform code to manage IRQ has been moved to MUSB,
and now the interrupt handler is completely generic.
Remove the isr callback that is not useful anymore.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the driver is already using DT to get the number of channels,
init_sched() is using an hardcoded value to get it.
Use DT to get the number of channels.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some constants are defined and use by the driver whereas they are
specifics to AM335x.
Add new variables to the glue layer, initialize them with the constants,
and use them in the driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, only the AM335x is supported by the driver.
Though the driver has a glue layer to support different platforms,
some platform variable names are not prefixed with the platform name.
To facilitate the addition of a new platform,
rename some variables owned by the AM335x glue.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to make CPPI 4.1 DMA driver more generic, accesses to USBSS
have been removed. So it is not required anymore to map the "glue"
register's.
Remove usbss_mem.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Trivial fix to spelling mistake and make channel plural.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code responsible for splitting periods into chunks that
can be handled by the DMA controller missed to update total_len,
the number of bytes processed in the current period, when there
are more chunks to follow.
Therefore total_len was stuck at 0 and the code didn't work at all.
This resulted in a wrong control block layout and audio issues because
the cyclic DMA callback wasn't executing on period boundaries.
Fix this by adding the missing total_len update.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
But first update usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is one
major place that will be used.)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lDg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylwfwCgyExa4x8Lur2nZyu8cgcaVRU68VAAoNQh0WJt
EZdEhEkRMt4d64j+ApYI
=iv7x
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is
one major place that will be used.)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
tty: pl011: Work around QDF2400 E44 stuck BUSY bit
atmel_serial: Use the fractional divider when possible
tty: Remove extra include in HVC console tty framework
serial: exar: Enable MSI support
serial: exar: Move register defines from uapi header to consumer site
serial: pci: Remove unused pci_boards entries
serial: exar: Move Commtech adapters to 8250_exar as well
serial: exar: Fix feature control register constants
serial: exar: Fix initialization of EXAR registers for ports > 0
serial: exar: Fix mapping of port I/O resources
serial: sh-sci: fix hardware RX trigger level setting
tty/serial: atmel: ensure state is restored after suspending
serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
serdev: ttyport: check whether tty_init_dev() fails
serial: 8250_pci: make pciserial_detach_ports() static
ARM: dts: STiH410-b2260: Enable HW flow-control
ARM: dts: STiH407-family: Use new Pinctrl groups
ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
ARM: dts: STiH410-b2260: Identify the UART RTS line
dt-bindings: serial: Update 'uart-has-rtscts' description
...
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYrI1RAAoJEHwUBw8lI4NHMH4QALbxsOzil+Sl5gq27xK02ox3
8NGkVdAZgUlMI0m7VnPrdenhLy+t7wz383RM0/DUJfHqJItwxdR+895GRwe5TJTl
PJJMrrdURv6k24ZqUq1b8qKN51YOjp9aVX6sjKi531fcf1Cmj6nuquo8/gIlZtQC
GnLPQGqgK/i5EX/LGQwuHw4j6hESsLGu1vCPdJBSRGzlzd6T4rbmc2ApUjSB1PRO
uhmLrORdkbQnxnt1mUYDlEVwGy/0wVNML89k/SX1g/70NI2kvVUn2NX5Aq7+C+vl
iIdBfYXuPDnhygrze8jYNd6acc9MWyKp7uYelTtm+m4tvVMAD2UJS/eXgbgkcyLj
XoGGkfjDLlK40gQDqnWiNfLi+Dn899ZEwXvCZNsQa72RS32wiatu3ZG39x+a55mK
XISolM57iph975C4manY2sxLfOZmM5qmXg8+JGMppine5U2kmID44Y72jYKLNeUU
EjMCVeZidx7LFkAR8BfA5pZt2BBIooHcncIwD9MW9KsEMPqzMcjqg9Wvxn/hSIUu
VGPVnBZrz/IBSeN9sqMmXWVY0kI+teC7bFZHecZBOUylOyxcQ9ZBHT7Ie2wM2piM
fY4UYWTtn9p/YOrfE32iSn226ga6a0Pk1kEfWgOQ/KXmOd20D33z0NYY9xOQ/CXC
aT+Skn10zjYZbfU0MCp5
=pcdH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers"
* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
async_tx: deprecate broken support for channel switching
dmaengine: rcar-dmac: Widen DMA mask to 40 bits
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
dmaengine: Provide a wrapper for memcpy operations
dmaengine: zx: fix build warning
dmaengine: dw: we do support Merrifield SoC in PCI mode
dmaengine: dw: add support of iDMA 32-bit hardware
dmaengine: dw: introduce register mappings for iDMA 32-bit
dmaengine: dw: introduce block2bytes() and bytes2block()
dmaengine: dw: extract dwc_chan_pause() for future use
dmaengine: dw: replace convert_burst() with one liner
dmaengine: dw: register IRQ and DMA pool with instance ID
dmaengine: dw: Fix data corruption in large device to memory transfers
dmaengine: ste_dma40: indicate granularity on channels
dmaengine: ste_dma40: indicate directions on channels
dmaengine: stm32-dma: Add error messages if xlate fails
dmaengine: dw: pci: remove LPE Audio DMA ID
dmaengine: stm32-dma: Add max_burst support
dmaengine: stm32-dma: Add synchronization support
dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
...
By default, the DMA mask covers only the low 32-bit address space, which
causes SWIOTLB on arm64 to fall back to a bounce buffer for DMA
transfers involving memory outside the 32-bit address space.
The R-Car DMA controller hardware supports a 40-bit address space, hence
widen the DMA mask to 40 bits to actually make use of this feature.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As 64-bit Allwinner H5 SoC has the same DMA engine with H3, the DMA
driver should be allowed to be built for ARM64, in order to make it work on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The static bug finder EBA (http://www.iagoabal.eu/eba/) reported the
following double-lock bug:
Double lock:
1. spin_lock_irqsave(pch->lock, flags) at pl330_free_chan_resources:2236;
2. call to function `pl330_release_channel' immediately after;
3. call to function `dma_pl330_rqcb' in line 1753;
4. spin_lock_irqsave(pch->lock, flags) at dma_pl330_rqcb:1505.
I have fixed it as suggested by Marek Szyprowski.
First, I have replaced `pch->lock' with `pl330->lock' in functions
`pl330_alloc_chan_resources' and `pl330_free_chan_resources'. This avoids
the double-lock by acquiring a different lock than `dma_pl330_rqcb'.
NOTE that, as a result, `pl330_free_chan_resources' executes
`list_splice_tail_init' on `pch->work_list' under lock `pl330->lock',
whereas in the rest of the code `pch->work_list' is protected by
`pch->lock'. I don't know if this may cause race conditions. Similarly
`pch->cyclic' is written by `pl330_alloc_chan_resources' under
`pl330->lock' but read by `pl330_tx_submit' under `pch->lock'.
Second, I have removed locking from `pl330_request_channel' and
`pl330_release_channel' functions. Function `pl330_request_channel' is
only called from `pl330_alloc_chan_resources', so the lock is already
held. Function `pl330_release_channel' is called from
`pl330_free_chan_resources', which already holds the lock, and from
`pl330_del'. Function `pl330_del' is called in an error path of
`pl330_probe' and at the end of `pl330_remove', but I assume that there
cannot be concurrent accesses to the protected data at those points.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix build warning that related to PAGE_SIZE. The maximum DMA
length has nothing to do with PAGE_SIZE, just use a fix number
for the definition.
drivers/dma/zx_dma.c: In function 'zx_dma_prep_memcpy':
drivers/dma/zx_dma.c:523:8: warning: division by zero [-Wdiv-by-zero]
drivers/dma/zx_dma.c: In function 'zx_dma_prep_slave_sg':
drivers/dma/zx_dma.c:567:11: warning: division by zero [-Wdiv-by-zero]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel Merrifield platform contains Intel integrated DMA (iDMA 32-bit) which has
a slightly different register mapping, e.g. some bits in CTL_* and CFG_*
channel registers, and has to use platform data since there is no
autoconfiguration.
The iDMA 32-bit specification is available in the publicly available
documentation for Intel Braswell and BayTrail SoCs as LPE Audio DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit is Intel designed DMA controller that behaves like Synopsys
Designware DMA. This patch adds a support of the new Intel hardware.
Due to iDMA 32-bit has no autoconfiguration the platform code must
provide a platform data to dw_dma_probe().
By default full FIFO (1024 bytes) is assigned to channel 0. Here we
slice FIFO on equal parts between channels for iDMA 32-bit case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The integrated DMA (iDMA 32-bit) is Intel designed DMA controller which
mimics Synopsys Designware DMA. This patch appends the register mappings
for the parts which are slightly different to the DesignWare hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly introduced helpers prepare driver to support new DMA controller
hardware.
While here, introduce DWC_CTLH_BLOCK_TS() macro as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit has a special handling of the FIFO during pause() /
terminate_all(). Prepare code to implement that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace convert_burst() with one liner in place.
The change simplifies further extension of the driver to cover new DMA
controller hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.
All current users of this IP would be enhanced later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When transferring more data than the maximum block size supported by the
HW multiplied by source width the transfer is split into smaller chunks.
Currently code calculates the memory width and thus aligment before
splitting for both memory to device and device to memory transfers.
For memory to device transfers this work fine since alignment is preserved
through the splitting and split blocks are still memory width aligned.
However in device to memory transfers aligment breaks when maximum block
size multiplied by register width doesn't have the same alignment than the
buffer. For instance when transferring from an 8-bit register 4100 bytes
(32-bit aligned) on a DW DMA that has maximum block size of 4095 elements.
An attempt to do such transfers caused data corruption.
Fix this by calculating and setting the destination memory width after
splitting by using the split block aligment and length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With patches "dmaengine: cppi41: Fix runtime PM timeouts with USB mass
storage", and "dmaengine: cppi41: Fix oops in cppi41_runtime_resume",
the pm_runtime_get/put() in cppi41_irq() is no longer needed. We now
guarantee that cppi41 is enabled when dma is in use.
We can still get pointless error -115 when musb is configured as a
usb peripheral. That's because we should now check for the state of
is_suspended instead.
Let's just remove the now useless code and replace it with a WARN().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
together with recent MUSB changes allowed USB and DMA on BeagleBone to idle
when no cable is connected. But looks like few corner case issues still
remain.
Looks like just by re-plugging USB cable about ten or so times on BeagleBone
when configured in USB peripheral mode we can get warnings and eventually
trigger an oops in cppi41 DMA:
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:1154 cppi41_runtime_suspend+
x28/0x38 [cppi41]
...
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:452
push_desc_queue+0x94/0x9c [cppi41]
...
Unable to handle kernel NULL pointer dereference at virtual
address 00000104
pgd = c0004000
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
...
[<bf0d92cc>] (cppi41_runtime_resume [cppi41]) from [<c0589838>]
(__rpm_callback+0xc0/0x214)
[<c0589838>] (__rpm_callback) from [<c05899ac>] (rpm_callback+0x20/0x80)
[<c05899ac>] (rpm_callback) from [<c0589460>] (rpm_resume+0x504/0x78c)
[<c0589460>] (rpm_resume) from [<c058a1a0>] (pm_runtime_work+0x60/0xa8)
[<c058a1a0>] (pm_runtime_work) from [<c0156120>] (process_one_work+0x2b4/0x808)
This is because of a race with runtime PM and cppi41_dma_issue_pending()
as reported by Alexandre Bailon <abailon@baylibre.com> in earlier
set of patches. Based on mailing list discussions we however came to the
conclusion that a different fix from Alexandre's fix is needed in order
to guarantee that DMA is really active when we try to use it.
To fix the issue, we need to add a driver specific flag as we otherwise
can have -EINPROGRESS state set by runtime PM and can't rely on
pm_runtime_active() to tell us when we can use the DMA.
And we need to make sure the DMA transfers get triggered in the queued
order. So let's always queue the transfers, then flush the queue
from both cppi41_dma_issue_pending() and cppi41_runtime_resume()
as suggested by Grygorii Strashko <grygorii.strashko@ti.com> in an
earlier example patch.
For reference, this is also documented in Documentation/power/runtime_pm.txt
in the example at the end of the file as pointed out by Grygorii Strashko
<grygorii.strashko@ti.com>.
Based on earlier patches from Alexandre Bailon <abailon@baylibre.com>
and Grygorii Strashko <grygorii.strashko@ti.com> modified based on
testing and what was discussed on the mailing lists.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
added runtime PM support for cppi41, but had corner case issues. Some of
the issues were fixed with commit 098de42ad6 ("dmaengine: cppi41: Fix
unpaired pm runtime when only a USB hub is connected"). That fix however
caused a new regression where we can get error -115 messages with USB on
BeagleBone when connecting a USB mass storage device to a hub.
This is because when connecting a USB mass storage device to a hub, the
initial DMA transfers can take over 200ms to complete and cppi41
autosuspend delay times out.
To fix the issue, we want to implement refcounting for chan_busy array
that contains the active dma transfers. Increasing the autosuspend delay
won't help as that the delay could be potentially seconds, and it's best
to let the USB subsystem to deal with the timeouts on errors.
The earlier attempt for runtime PM was buggy as the pm_runtime_get/put()
calls could get unpaired easily as they did not follow the state of
the chan_busy array as described in commit 098de42ad6 ("dmaengine:
cppi41: Fix unpaired pm runtime when only a USB hub is connected".
Let's fix the issue by adding pm_runtime_get() to where a new transfer
is added to the chan_busy array, and calls to pm_runtime_put() where
chan_busy array entry is cleared. This prevents any autosuspend timeouts
from happening while dma transfers are active.
Fixes: 098de42ad6 ("dmaengine: cppi41: Fix unpaired pm runtime when
only a USB hub is connected")
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PL330 is hard-wired such that instruction fetches on both the
manager and channel threads go out onto the bus with the "privileged"
bit set. This can become troublesome once there is an IOMMU or other
form of memory protection downstream, since those will typically be
programmed by the DMA mapping subsystem in the expectation of normal
unprivileged transactions (such as the PL330 channel threads' own data
accesses as currently configured by this driver).
To avoid the case of, say, an IOMMU blocking an unexpected privileged
transaction with a permission fault, use the newly-introduced
DMA_ATTR_PRIVILEGED attribute for the mapping of our microcode buffer.
That way the DMA layer can do whatever it needs to do to make things
continue to work as expected on more complex systems.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
[rm: remove now-redundant local variable, clarify commit message]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
irq 54: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6-edison64-86244934+ #1
Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
ffff88003f203eb0 ffffffff8130e718 ffff880032627000 ffff88003262709c
ffff88003f203ed8 ffffffff810a3960 ffff880032627000 0000000000000000
ffff880032627000 ffff88003f203f10 ffffffff810a3cc7 ffff880032627000
Call Trace:
<IRQ>
[<ffffffff8130e718>] dump_stack+0x4d/0x65
[<ffffffff810a3960>] __report_bad_irq+0x30/0xc0
[<ffffffff810a3cc7>] note_interrupt+0x227/0x270
[<ffffffff810a1380>] handle_irq_event_percpu+0x40/0x50
[<ffffffff810a13b7>] handle_irq_event+0x27/0x50
[<ffffffff810a42d5>] handle_fasteoi_irq+0x85/0x150
[<ffffffff8101d7fe>] handle_irq+0x6e/0x120
[<ffffffff8105b8bc>] ? _local_bh_enable+0x1c/0x50
[<ffffffff8101d0d6>] do_IRQ+0x46/0xd0
[<ffffffff818cef3f>] common_interrupt+0x7f/0x7f
<EOI>
[<ffffffff818cdead>] ? mwait_idle+0x7d/0x140
[<ffffffff81024c9a>] arch_cpu_idle+0xa/0x10
[<ffffffff818ce150>] default_idle_call+0x20/0x30
[<ffffffff810908fd>] cpu_startup_entry+0x16d/0x1d0
[<ffffffff818c882d>] rest_init+0x6d/0x70
[<ffffffff81f93e8f>] start_kernel+0x3e2/0x3ef
[<ffffffff81f9343d>] x86_64_start_reservations+0x38/0x3a
[<ffffffff81f93529>] x86_64_start_kernel+0xea/0xed
handlers:
[<ffffffff81411670>] serial8250_interrupt
Disabling IRQ #54
Fix this by handling interrupt only in one place.
The issue is discussed here: https://github.com/andy-shev/linux/issues/5
Moreover this also fixes another bug when Rx DMA returns wrong residue and we
can't rely on it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ste_dma40 has burst level granularity on the residue
registers, which is necessary for some clients to know,
notably the UART. Before this patch we get this message:
uart-pl011 80007000.uart: RX DMA disabled - no residue processing
This patch fixes it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the introduction of the .directions flags, ste_dma40 was
never patched to indicate which transfer directions it can manage.
This causes a problem when trying to use the dmaengine for generic
ALSA SoC DMA:
ux500-msp-i2s.1: Failed to get DMA channel capabilities, falling
back to period counting: -6
This patch fixes this issue by indicating the supported transfer
directions for slave and memcpy channels.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The slave mapping should be removed together with other channel
resources when the channel is freed. If it's not unmapped it will hang
around forever after the channel is freed.
Fixes: 9f878603db ("dmaengine: rcar-dmac: add iommu support for slave transfers")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We do not yet have users of port_window. The following errors were found
when converting the tusb6010_omap.c musb driver:
- The peripheral side must have SRC_/DST_PACKED disabled
- when configuring the burst for the peripheral side the memory side
configuration were overwritten: d->csdp = ... -> d->csdp |= ...
- The EI and FI were configured for the wrong sides of the transfers.
With these changes and the converted tus6010_omap.c I was able to verify
that things are working as they expected to work.
Fixes: 201ac4861c ("dmaengine: omap-dma: Support for slave devices with data port window")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds some error messages when a slave device fails to request a
channel.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On a kernel with DEBUG_LOCKS, ioat_free_chan_resources triggers an
in_interrupt() warning. With PROVE_LOCKING, it reports detecting a
SOFTIRQ-safe to SOFTIRQ-unsafe lock ordering in the same code path.
This is because dma_generic_alloc_coherent() checks if the GFP flags
permit blocking. It allocates from different subsystems if blocking is
permitted. The free path knows how to return the memory to the correct
allocator. If GFP_KERNEL is specified then the alloc and free end up
going through cma_alloc(), which uses mutexes.
Given that ioat_free_chan_resources() can be called in interrupt
context, ioat_alloc_chan_resources() must specify GFP_NOWAIT so that the
allocations do not block and instead use an allocator that uses
spinlocks.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Antonio Borneo