Allows us to gut a BO of it's backing store when the driver says that it
isn't needed any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
this patch actually refactor mailbox implmentations, and
all below changes are needed together to fix all those mailbox
handshake issues exposured by heavey TDR test.
1)refactor all mailbox functions based on byte accessing for mb_control
reason is to avoid touching non-related bits when writing trn/rcv part of
mailbox_control, this way some incorrect INTR sent to hypervisor
side could be avoided, and it fixes couple handshake bug.
2)trans_msg function re-impled: put a invalid
logic before transmitting message to make sure the ACK bit is in
a clear status, otherwise there is chance that ACK asserted already
before transmitting message and lead to fake ACK polling.
(hypervisor side have some tricks to workaround ACK bit being corrupted
by VF FLR which hase an side effects that may make guest side ACK bit
asserted wrongly), and clear TRANS_MSG words after message transferred.
3)for mailbox_flr_work, it is also re-worked: it takes the mutex lock
first if invoked, to block gpu recover's participate too early while
hypervisor side is doing VF FLR. (hypervisor sends FLR_NOTIFY to guest
before doing VF FLR and sentds FLR_COMPLETE after VF FLR done, and
the FLR_NOTIFY will trigger interrupt to guest which lead to
mailbox_flr_work being invoked)
This can avoid the issue that mailbox trans msg being cleared by its VF FLR.
4)for mailbox_rcv_irq IRQ routine, it should only peek msg and schedule
mailbox_flr_work, instead of ACK to hypervisor itself, because FLR_NOTIFY
msg sent from hypervisor side doesn't need VF's ACK (this is because
VF's ACK would lead to hypervisor clear its trans_valid/msg, and this
would cause handshake bug if trans_valid/msg is cleared not due to
correct VF ACK but from a wrong VF ACK like this "FLR_NOTIFY" one)
This fixed handshake bug that sometimes GUEST always couldn't receive
"READY_TO_ACCESS_GPU" msg from hypervisor.
5)seperate polling time limite accordingly:
POLL ACK cost no more than 500ms
POLL MSG cost no more than 12000ms
POLL FLR finish cost no more than 500ms
6) we still need to set adev into in_gpu_reset mode after we received
FLR_NOTIFY from host side, this can prevent innocent app wrongly succesed
to open amdgpu dri device.
FLR_NOFITY is received due to an IDLE hang detected from hypervisor side
which indicating GPU is already die in this VF.
v2:
use MACRO as the offset of mailbox_control register
don't test if NOTIFY_CMPL event in rcv_msg since it won't
recieve that message anymore
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Pixel Ding <Pixel.Ding@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mailbox registers can be accessed with a byte boundry according
to BIF team, so this patch prepares register byte access
and will be used by following patches.
Actually, for mailbox registers once the byte field is touched even not changed,
the mailbox behaves, so we need the byte width accessing to those sort of regs.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Pixel Ding <Pixel.Ding@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vram type for dGPU is stored in umc_info while sys mem type
for APU is stored in integratedsysteminfo
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The commit d296278fd372003fc69588acfd0c0c5edbdf4874 added support for
detecting DDR4 but omitted the label that is printed out in
amdgpu_bo_init() resulting in a KASAN error.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The amdgpu_ucode_fini_bo should be called after gfx_v8_0_hw_fini,
or it will have KCQ disable failed issue.
For Tonga, as it firstly finishes SMC block, and the SMC hw fini
will call amdgpu_ucode_fini, which will lead the amdgpu_ucode_fini_bo
called before gfx_v8_0_hw_fini, this is incorrect.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The amdgpu_pm_sysfs_fini should call before amdgpu_device_ip_fini,
or the adev->pm.dpm_enabled would be set to 0, then the device files
related to pp won't be removed by amdgpu_pm_sysfs_fini when unload
driver.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't need the page array for prime shared BOs, stop allocating it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows drivers to only allocate dma addresses, but not a page
array.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Let's stop mangling everything in a single header and create one header
per object instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
- Query uAPI interface (used for GPU topology information currently)
* Mesa: https://patchwork.freedesktop.org/series/38795/
Driver Changes:
- Increase PSR2 size for CNL (DK)
- Avoid retraining LSPCON link unnecessarily (Ville)
- Decrease request signaling latency (Chris)
- GuC error capture fix (Daniele)
* tag 'drm-intel-next-2018-03-08' of git://anongit.freedesktop.org/drm/drm-intel: (127 commits)
drm/i915: Update DRIVER_DATE to 20180308
drm/i915: add schedule out notification of preempted but completed request
drm/i915: expose rcs topology through query uAPI
drm/i915: add query uAPI
drm/i915: add rcs topology to error state
drm/i915/debugfs: add rcs topology entry
drm/i915/debugfs: reuse max slice/subslices already stored in sseu
drm/i915: store all subslice masks
drm/i915/guc: work around gcc-4.4.4 union initializer issue
drm/i915/cnl: Add Wa_2201832410
drm/i915/icl: Gen11 forcewake support
drm/i915/icl: Add Indirect Context Offset for Gen11
drm/i915/icl: Enhanced execution list support
drm/i915/icl: new context descriptor support
drm/i915/icl: Correctly initialize the Gen11 engines
drm/i915: Assert that the request is indeed complete when signaled from irq
drm/i915: Handle changing enable_fbc parameter at runtime better.
drm/i915: Track whether the DP link is trained or not
drm/i915: Nuke intel_dp->channel_eq_status
drm/i915: Move SST DP link retraining into the ->post_hotplug() hook
...
Major points for this pull request:
- Add dGPU support for amdkfd initialization code and queue handling. It's
not complete support since the GPUVM part is missing (the under debate stuff).
- Enable PCIe atomics for dGPU if present
- Various adjustments to the amdgpu<-->amdkfd interface for dGPUs
- Refactor IOMMUv2 code to allow loading amdkfd without IOMMUv2 in the system
- Add HSA process eviction code in case of system memory pressure
- Various fixes and small changes
* tag 'drm-amdkfd-next-2018-03-11' of git://people.freedesktop.org/~gabbayo/linux: (24 commits)
uapi: Fix type used in ioctl parameter structures
drm/amdkfd: Implement KFD process eviction/restore
drm/amdkfd: Add GPUVM virtual address space to PDD
drm/amdkfd: Remove unaligned memory access
drm/amdkfd: Centralize IOMMUv2 code and make it conditional
drm/amdgpu: Add submit IB function for KFD
drm/amdgpu: Add GPUVM memory management functions for KFD
drm/amdgpu: add amdgpu_sync_clone
drm/amdgpu: Update kgd2kfd_shared_resources for dGPU support
drm/amdgpu: Add KFD eviction fence
drm/amdgpu: Remove unused kfd2kgd interface
drm/amdgpu: Fix wrong mask in get_atc_vmid_pasid_mapping_pasid
drm/amdgpu: Fix header file dependencies
drm/amdgpu: Replace kgd_mem with amdgpu_bo for kernel pinned gtt mem
drm/amdgpu: remove useless BUG_ONs
drm/amdgpu: Enable KFD initialization on dGPUs
drm/amdkfd: Add dGPU device IDs and device info
drm/amdkfd: Add dGPU support to kernel_queue_init
drm/amdkfd: Add dGPU support to the MQD manager
drm/amdkfd: Add dGPU support to the device queue manager
...
More stuff for 4.17. Highlights:
- More fixes for "wattman" like functionality (fine grained clk/voltage control)
- Add more power profile infrastucture (context based dpm)
- SR-IOV fixes
- Add iomem debugging interface for use with umr
- Powerplay and cgs cleanups
- DC fixes and cleanups
- ttm improvements
- Misc cleanups all over
* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux: (143 commits)
drm/amdgpu:Always save uvd vcpu_bo in VM Mode
drm/amdgpu:Correct max uvd handles
drm/amdgpu: replace iova debugfs file with iomem (v3)
drm/amd/display: validate plane format on primary plane
drm/amdgpu: Clean sdma wptr register when only enable wptr polling
drm/amd/amdgpu: re-add missing GC 9.1 and SDMA0 4.1 sh_mask header files
drm/amdgpu: give warning before sleep in kiq_r/wreg
drm/amdgpu: further mitigate workaround for i915
drm/amdgpu: drop gtt->adev
drm/amdgpu: add amdgpu_evict_gtt debugfs entry
drm/amd/pp: Add #ifdef checks for CONFIG_ACPI
drm/amd/pp: fix "Delete the wrapper layer of smu_allocate/free_memory"
drm/amd/pp: Drop wrapper functions for upper/lower_32_bits
drm/amdgpu: Delete cgs wrapper functions for gpu memory manager
drm/amd/pp: Delete the wrapper layer of smu_allocate/free_memory
drm/amd/pp: Remove cgs wrapper function for temperature update
Revert "drm/amd/pp: Add a pp feature mask bit for AutoWattman feature"
drm/amd/pp: Add auto power profilng switch based on workloads (v2)
drm/amd/pp: Revert gfx/compute profile switch sysfs
drm/amd/pp: Fix sclk in highest two levels when compute on smu7
...
- Convert LVDS support to a drm_bridge driver
- Add DT bindings for the R8A77995 SoC
- Add DT bindings and driver support for the R8A77970 SoC
Note that the LVDS conversion depends on a patch series from Frank Rowand that
will make it upstream through Rob Herring's tree. Frank has provided a stable
branch based on v4.16-rc1 with the patches, and both Rob and I have merged it
into our trees. This should thus generate no conflict when reaching -next.
* 'drm/next/du' of git://linuxtv.org/pinchartl/media:
dt-bindings: display: renesas: lvds: Document r8a77995 bindings
dt-bindings: display: renesas: du: Document r8a77995 bindings
drm: rcar-du: lvds: Add R8A77970 support
drm: rcar-du: Add R8A77970 support
dt-bindings: display: renesas: lvds: Document R8A77970 bindings
dt-bindings: display: renesas: du: Document R8A77970 bindings
drm: rcar-du: Convert LVDS encoder code to bridge driver
drm: rcar-du: Fix legacy DT to create LVDS encoder nodes
dt-bindings: display: renesas: Deprecate LVDS support in the DU bindings
dt-bindings: display: renesas: Add R-Car LVDS encoder DT bindings
of: improve reporting invalid overlay target path
of: convert unittest overlay devicetree source to sugar syntax
of: Documentation: of_overlay_apply() replaced by of_overlay_fdt_apply()
of: change overlay apply input data from unflattened to FDT
x86: devicetree: fix config option around x86_flattree_get_config()
Instead of using timer and spinlocks, use delayed_work and
mutexes for rockchip psr. This allows us to make blocking
calls when enabling/disabling psr (which is sort of important
given we're talking over dpcd to the display).
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305222324.5872-3-enric.balletbo@collabora.com
There's a race between when bridge_disable and when vop_crtc_disable
are called. If the flush timer triggers a new psr work between these,
we will operate eDP without power shutdowned by bridge_disable. In this
case, moving activate/deactivate to enable/disable bridge to avoid it.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305222324.5872-2-enric.balletbo@collabora.com
The HDMI vpll clock should be enabled when bind() is called. So move the
clk_prepare_enable of that clock to bind() function and add the missing
clk_disable_unprepare() required in error handling path and unbind().
Fixes: 12b9f204e8 ("drm: bridge/dw_hdmi: add rockchip rk3288 support")
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302175757.28192-5-enric.balletbo@collabora.com
In bind the clk_prepare_enable of the HDMI pclk is called before adding the
i2c_adapter. So it should be the other way around in unbind, first remove
the i2c_adapter and then call the clk_disable_unprepare.
Fixes: 412d4ae6b7 ("drm/rockchip: hdmi: add Innosilicon HDMI support")
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302175757.28192-4-enric.balletbo@collabora.com
In bind()'s error handling path call destroy functions instead of
cleanup functions for encoder and connector and reorder to match how is
called in bind().
In unbind() call the connector and encoder destroy functions.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302175757.28192-2-enric.balletbo@collabora.com
Replace the ad-hoc iturbt_709 property with the new standard
COLOR_ENCODING property. Compiles, but not tested.
v2: Fix typos (Ilia)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: nouveau@lists.freedesktop.org
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134816.15229-1-ville.syrjala@linux.intel.com
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Acked-by: Ben Skeggs <bskeggs@redhat.com> #irc
There is one corner case missing schedule out notification of the preempted
request. The preempted request is just completed when preemption happen,
then it will be canceled and won't be resubmitted later, GVT-g will lost
the schedule out notification.
Here add schedule out notification if found the preempted request has been
completed.
v2:
- refine description, add completed check and notification in
execlists_cancel_port_requests. (Chris)
v3:
- use ternary confitional, remove local variable. (Tvrtko)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520302557-25079-1-git-send-email-weinan.z.li@intel.com
With the introduction of asymmetric slices in CNL, we cannot rely on
the previous SUBSLICE_MASK getparam to tell userspace what subslices
are available. Here we introduce a more detailed way of querying the
Gen's GPU topology that doesn't aggregate numbers.
This is essential for monitoring parts of the GPU with the OA unit,
because counters need to be normalized to the number of
EUs/subslices/slices. The current aggregated numbers like EU_TOTAL do
not gives us sufficient information.
The Mesa series making use of this API is :
https://patchwork.freedesktop.org/series/38795/
As a bonus we can draw representations of the GPU :
https://imgur.com/a/vuqpa
v2: Rename uapi struct s/_mask/_info/ (Tvrtko)
Report max_slice/subslice/eus_per_subslice rather than strides (Tvrtko)
Add uapi macros to read data from *_info structs (Tvrtko)
v3: Use !!(v & DRM_I915_BIT()) for uapi macros instead of custom shifts (Tvrtko)
v4: factorize query item writting (Tvrtko)
tweak uapi struct/define names (Tvrtko)
v5: Replace ALIGN() macro (Chris)
v6: Updated uapi comments (Tvrtko)
Moved flags != 0 checks into vfuncs (Tvrtko)
v7: Use access_ok() before copying anything, to avoid overflows (Chris)
Switch BUG_ON() to GEM_WARN_ON() (Tvrtko)
v8: Tweak uapi comments style to match the coding style (Lionel)
v9: Fix error in comment about computation of enabled subslice (Tvrtko)
v10: Fix/update comments in uAPI (Sagar)
v11: Drop drm_i915_query_(slice|subslice|eu)_info in favor of a single
drm_i915_query_topology_info (Joonas)
v12: Add subslice_stride/eu_stride in drm_i915_query_topology_info (Joonas)
v13: Fix comment in uAPI (Joonas)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-7-lionel.g.landwerlin@intel.com
There are a number of information that are readable from hardware
registers and that we would like to make accessible to userspace. One
particular example is the topology of the execution units (how are
execution units grouped in subslices and slices and also which ones
have been fused off for die recovery).
At the moment the GET_PARAM ioctl covers some basic needs, but
generally is only able to return a single value for each defined
parameter. This is a bit problematic with topology descriptions which
are array/maps of available units.
This change introduces a new ioctl that can deal with requests to fill
structures of potentially variable lengths. The user is expected fill
a query with length fields set at 0 on the first call, the kernel then
sets the length fields to the their expected values. A second call to
the kernel with length fields at their expected values will trigger a
copy of the data to the pointed memory locations.
The scope of this uAPI is only to provide information to userspace,
not to allow configuration of the device.
v2: Simplify dispatcher code iteration (Tvrtko)
Tweak uapi drm_i915_query_item structure (Tvrtko)
v3: Rename pad fields into flags (Chris)
Return error on flags field != 0 (Chris)
Only copy length back to userspace in drm_i915_query_item (Chris)
v4: Use array of functions instead of switch (Chris)
v5: More comments in uapi (Tvrtko)
Return query item errors in length field (All)
v6: Tweak uapi comments style to match the coding style (Lionel)
v7: Add i915_query.h (Joonas)
v8: (Lionel) Change the behavior of the item iterator to report
invalid queries into the query item rather than stopping the
iteration. This enables userspace applications to query newer
items on older kernels and only have failure on the items that are
not supported.
v9: Edit copyright headers (Joonas)
v10: Typos & comments in uapi (Joonas)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-6-lionel.g.landwerlin@intel.com
This might be useful information for developers looking at an error
state.
v2: Place topology towards the end of the error state (Chris)
v3: Reuse common printing code (Michal)
v4: Make this a one-liner (Chris)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-5-lionel.g.landwerlin@intel.com
While the end goal is to make this information available to userspace
through a new ioctl, there is no reason we can't display it in a human
readable fashion through debugfs.
slice0: 3 subslice(s) (0x7):
subslice0: 8 EUs (0xff)
subslice1: 8 EUs (0xff)
subslice2: 8 EUs (0xff)
subslice3: 0 EUs (0x0)
slice1: 3 subslice(s) (0x7):
subslice0: 8 EUs (0xff)
subslice1: 8 EUs (0xff)
subslice2: 8 EUs (0xff)
subslice3: 0 EUs (0x0)
slice2: 3 subslice(s) (0x7):
subslice0: 8 EUs (0xff)
subslice1: 8 EUs (0xff)
subslice2: 8 EUs (0xff)
subslice3: 0 EUs (0x0)
v2: Reformat debugfs printing (Tvrtko)
Use the new EU mask helper (Tvrtko)
v3: Move printing code to intel_device_info.c to be shared with error
state (Michal)
v4: Bump u8 to u16 when using sseu_get_eus() (Lionel)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-4-lionel.g.landwerlin@intel.com
Up to now, subslice mask was assumed to be uniform across slices. But
starting with Cannonlake, slices can be asymmetric (for example slice0
has different number of subslices as slice1+). This change stores all
subslices masks for all slices rather than having a single mask that
applies to all slices.
v2: Rework how we store total numbers in sseu_dev_info (Tvrtko)
Fix CHV eu masks, was reading disabled as enabled (Tvrtko)
Readability changes (Tvrtko)
Add EU index helper (Tvrtko)
v3: Turn ALIGN(v, 8) / 8 into DIV_ROUND_UP(v, BITS_PER_BYTE) (Tvrtko)
Reuse sseu_eu_idx() for setting eu_mask on CHV (Tvrtko)
Reformat debug prints for subslices (Tvrtko)
v4: Change eu_mask helper into sseu_set_eus() (Tvrtko)
v5: With Haswell reporting masks & counts, bump sseu_*_eus() functions
to use u16 (Lionel)
v6: Fix sseu_get_eus() for > 8 EUs per subslice (Lionel)
v7: Change debugfs enabels for number of subslices per slice, will
need a small igt/pm_sseu change (Lionel)
Drop subslice_total field from sseu_dev_info, rely on
sseu_subslice_total() to recompute the value instead (Lionel)
v8: Remove unused function compute_subslice_total() (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-2-lionel.g.landwerlin@intel.com
gcc-4.4.4 has problems with initalizers of anon unions.
drivers/gpu/drm/i915/intel_guc_log.c: In function 'guc_log_control':
drivers/gpu/drm/i915/intel_guc_log.c:64: error: unknown field 'logging_enabled' specified in initializer
Work around this.
Fixes: 35fe703c31 ("drm/i915/guc: Change values for i915_guc_log_control")
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308001333.rI2vrNRTY%akpm@linux-foundation.org
"Clock gating bug in GWL may not clear barrier state when an EOT
is received, causing a hang the next time that barrier is used."
HSDES: 2201832410
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307220912.3681-1-rodrigo.vivi@intel.com
We were previously selecting 1024x768 and 32BPP as the default
set-up for the PL111 consumers.
This does not work on elder systems: the device tree bindings
support a property "max-memory-bandwidth" in bytes/second that
states that if you exceed this the memory bus will saturate.
The result is flickering and unstable images.
Parse the "max-memory-bandwidth" and respect it when
intializing the driver. On the RealView PB11MP, Versatile and
Integrator/CP we get a nice console as default with this code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307215819.15814-1-linus.walleij@linaro.org
The following happens when connection a DVI output driven
from the SiI9022 using a DVI-to-VGA adapter plug:
i2c i2c-0: sendbytes: NAK bailout.
i2c i2c-0: sendbytes: NAK bailout.
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305101702.13441-1-linus.walleij@linaro.org
We want to cut down the default bpp to 16 on the RealView so
we can have a 1024x768 framebuffer console by default. The
memory bandwidth limitations makes this not work with the
PL111 default of 32bpp.
This builds on top of the earlier patches making the
framebuffer default bpp a per-variant variable.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302090948.6399-4-linus.walleij@linaro.org
This fixes up the .mode_valid() vtable entry documentation
by copyediting the documentation from the .mode_valid()
documentation in the drm_modeset_helper_vtables.h file.
Fixes: 40275dc4ed ("drm: simple_kms_helper: Add mode_valid() callback support")
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227101109.6088-1-linus.walleij@linaro.org
When UVD is in VM mode, there is not uvd handle exchanged,
uvd.handles are always 0. So vcpu_bo always need save,
Otherwise amdgpu driver will fail during suspend/resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105021
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Max uvd handles should use adev->uvd.max_handles instead of
AMDGPU_MAX_UVD_HANDLES here.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This allows access to pages allocated through the driver with optional
IOMMU mapping.
v2: Fix number of bytes copied and add write method
v3: drop check for kmap return
Original-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dce110, the plane configuration is such that plane 0
or the primary plane should be rendered with only RGB data.
This patch adds the validation to ensure that no video data
is rendered on plane 0.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The sdma wptr polling memory is not fast enough, then the sdma
wptr register will be random, and not equal to sdma rptr, which
will cause sdma engine hang when load driver, so clean up the sdma
wptr directly to fix this issue.
v2:add comment above the code and correct coding style
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are required by umr to properly parse bitfield offsets.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexdeucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to catch error that may schedule in atomic context early on
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable the workaround on imported BOs as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexdeucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can use ttm->bdev instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexdeucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow evicting all BOs from the GTT domain.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexdeucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
