DMA routers are transparent devices used to mux DMA requests from
peripherals to DMA controllers. They are used when the SoC integrates more
devices with DMA requests then their controller can handle.
DRA7x is one example of such SoC, where the sDMA can hanlde 128 DMA request
lines, but in SoC level it has 205 DMA requests.
The of_dma_router will be registered as of_dma_controller with special
xlate function and additional parameters. The driver for the router is
responsible to craft the dma_spec (in the of_dma_route_allocate callback)
which can be used to requests a DMA channel from the real DMA controller.
This way the router can be transparent for the system while remaining generic
enough to be used in different environments.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removed checkpatch reported spaces in indentation:
ERROR: code indent should use tabs where possible
+^I PL080_CONFIG_TC_IRQ_MASK);$
Signed-off-by: Leonardo Carreras <leocarreras89@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The 8250_omap serial driver relies on dmaengine_pause() actually
pausing the DMA transfer. Before this patch dmaengine_pause() is
a NOP for non-cylic DMA transfers. This allowed the 8250_omap
driver to read DMA buffers while the DMA was still active,
resulting in lost serial data.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sDMA controller is capable of performing memory copy operation. It need
to be configured to software triggered mode and without HW synchronization.
The sDMA can copy data which is aligned to 8, 16 or 32 bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Channels allocated via dma_get_any_slave_channel were not increasing
the counter tracking private allocations. When these channels were
released, privatecnt may erroneously fall to zero. The DMA device
would then lose its DMA_PRIVATE cap and fail to allocate future private
channels (via private_candidate) as any allocations still outstanding
would incorrectly be seen as public allocations.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The xgene-dma driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Rameshwar Prasad Sahu <rsahu@apm.com>
Cc: Loc Ho <lho@apm.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If CONFIG_PM=n:
drivers/dma/sh/usb-dmac.c:677: warning: ‘usb_dmac_runtime_suspend’ defined but not used
drivers/dma/sh/usb-dmac.c:688: warning: ‘usb_dmac_runtime_resume’ defined but not used
Protect the unused functions by #ifdef CONFIG_PM to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
HSU_DMA is selected by the HSU_DMA_PCI driver, this should be user selected
so remove the user prompt for this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DW_DMAC_CORE is slected by PCI or Platform driver, so this symbol shouldn't
be user selectable, so remove the prompt
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
This driver uses '#ifdef CONFIG_ARCH_SHMOBILE' and '#ifdef CONFIG_ARM'
interchangeably in its sh_dmae_probe function, which causes a build
warning when building for ARM without also enabling shmobile:
dma/sh/shdmac.c: In function sh_dmae_probe:
dma/sh/shdmac.c:696:6: warning: unused variable errirq [-Wunused-variable]
dma/sh/shdmac.c:695:16: warning: unused variable irqflags [-Wunused-variable]
dma/sh/shdmac.c: At top level:
dma/sh/shdmac.c:447:20: warning: sh_dmae_err defined but not used [-Wunused-function]
This changes all the #ifdef to test for CONFIG_ARCH_SHMOBILE to
avoid that warning. An earlier patch from Laurent had fixed the warning
for non-ARM case, but it still remained present in ARM randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 52d6a5ee10 ("DMA: shdma: Fix warnings due to declared but unused symbols")
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/xgene-dma.c:2079:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Memory allocated for pch_dma is not deallocated in case of failure
in pch_dma_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code here is checking for IS_ERR() but devm_ioremap() returns NULL
on error and not an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We put 9 characters into the 8 character name[] array. Let's make the
array bigger and change the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an issue that the usb_dmac_desc_free() is
dereferencing freed memory 'desc' because it uses list_for_each_entry().
This function should use list_for_each_entry_safe().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the following warning by initializing necessary fields in the dma_device
structure.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:863 dma_async_device_register+0x2b4/0x4f0()
this driver doesn't support generic slave capabilities reporting
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.0.0-rc5+ #10
Hardware name: Sharp-Collie
[<c0105cd8>] (unwind_backtrace) from [<c0103ef8>] (show_stack+0x10/0x14)
[<c0103ef8>] (show_stack) from [<c010e9b8>] (warn_slowpath_common+0x74/0xac)
[<c010e9b8>] (warn_slowpath_common) from [<c010ea20>] (warn_slowpath_fmt+0x30/0x40)
[<c010ea20>] (warn_slowpath_fmt) from [<c02956fc>] (dma_async_device_register+0x2b4/0x4f0)
[<c02956fc>] (dma_async_device_register) from [<c0296a9c>] (sa11x0_dma_probe+0x21c/0x358)
[<c0296a9c>] (sa11x0_dma_probe) from [<c02c52c0>] (platform_drv_probe+0x30/0x94)
[<c02c52c0>] (platform_drv_probe) from [<c02c39bc>] (driver_probe_device+0x84/0x234)
[<c02c39bc>] (driver_probe_device) from [<c02c3c4c>] (__driver_attach+0x98/0x9c)
[<c02c3c4c>] (__driver_attach) from [<c02c1f9c>] (bus_for_each_dev+0x74/0xa4)
[<c02c1f9c>] (bus_for_each_dev) from [<c02c3230>] (bus_add_driver+0x13c/0x1e8)
[<c02c3230>] (bus_add_driver) from [<c02c4260>] (driver_register+0x78/0xf8)
[<c02c4260>] (driver_register) from [<c0100624>] (do_one_initcall+0x84/0x1f4)
[<c0100624>] (do_one_initcall) from [<c0700e1c>] (kernel_init_freeable+0xf8/0x1b4)
[<c0700e1c>] (kernel_init_freeable) from [<c040a920>] (kernel_init+0x8/0xf0)
[<c040a920>] (kernel_init) from [<c01013a8>] (ret_from_fork+0x14/0x2c)
---[ end trace e188b8fe0e782e75 ]---
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There have been major modernization with the standard bus: in ALSA
sequencer core and HD-audio. Also, HD-audio receives the regmap
support replacing the in-house cache register cache code. These
changes shouldn't impact the existing behavior, but rather
refactoring.
In addition, HD-audio got the code split to a core library part and
the "legacy" driver parts. This is a preliminary work for adapting
the upcoming ASoC HD-audio driver, and the whole transition is still
work in progress, likely finished in 4.1.
Along with them, there are many updates in ASoC area as usual, too:
lots of cleanups, Intel code shuffling, etc.
Here are some highlights:
ALSA core:
- PCM: the audio timestamp / wallclock enhancement
- PCM: fixes in DPCM management
- Fixes / cleanups of user-space control element management
- Sequencer: modernization using the standard bus
HD-audio:
- Modernization using the standard bus
- Regmap support
- Use standard runtime PM for codec power saving
- Widget-path based power-saving for IDT, VIA and Realtek codecs
- Reorganized sysfs entries for each codec object
- More Dell headset support
ASoC:
- Move of jack registration to the card level
- Lots of ASoC cleanups, mainly moving things from the CODEC level
to the card level
- Support for DAPM routes specified by both the machine driver and DT
- Continuing improvements to rcar
- pcm512x enhacements
- Intel platforms updates
- rt5670 updates / fixes
- New platforms / devices: some non-DSP Qualcomm platforms, Google's
Storm platform, Maxmim MAX98925 CODECs and the Ingenic JZ4780 SoC
Misc:
- ice1724: Improved ESI W192M support
- emu10k1: Emu 1010 fixes/enhancement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4z5j
-----END PGP SIGNATURE-----
Merge tag 'sound-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been major modernization with the standard bus: in ALSA
sequencer core and HD-audio. Also, HD-audio receives the regmap
support replacing the in-house cache register cache code. These
changes shouldn't impact the existing behavior, but rather
refactoring.
In addition, HD-audio got the code split to a core library part and
the "legacy" driver parts. This is a preliminary work for adapting
the upcoming ASoC HD-audio driver, and the whole transition is still
work in progress, likely finished in 4.1.
Along with them, there are many updates in ASoC area as usual, too:
lots of cleanups, Intel code shuffling, etc.
Here are some highlights:
ALSA core:
- PCM: the audio timestamp / wallclock enhancement
- PCM: fixes in DPCM management
- Fixes / cleanups of user-space control element management
- Sequencer: modernization using the standard bus
HD-audio:
- Modernization using the standard bus
- Regmap support
- Use standard runtime PM for codec power saving
- Widget-path based power-saving for IDT, VIA and Realtek codecs
- Reorganized sysfs entries for each codec object
- More Dell headset support
ASoC:
- Move of jack registration to the card level
- Lots of ASoC cleanups, mainly moving things from the CODEC level to
the card level
- Support for DAPM routes specified by both the machine driver and DT
- Continuing improvements to rcar
- pcm512x enhacements
- Intel platforms updates
- rt5670 updates / fixes
- New platforms / devices: some non-DSP Qualcomm platforms, Google's
Storm platform, Maxmim MAX98925 CODECs and the Ingenic JZ4780 SoC
Misc:
- ice1724: Improved ESI W192M support
- emu10k1: Emu 1010 fixes/enhancement"
* tag 'sound-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
ALSA: hda - set GET bit when adding a vendor verb to the codec regmap
ALSA: hda/realtek - Enable the ALC292 dock fixup on the Thinkpad T450
ALSA: hda - Fix another race in runtime PM refcounting
ALSA: hda - Expose codec type sysfs
ALSA: ctl: fix to handle several elements added by one operation for userspace element
ASoC: Intel: fix array_size.cocci warnings
ASoC: n810: Automatically disconnect non-connected pins
ASoC: n810: Consistently pass the card DAPM context to n810_ext_control()
ASoC: davinci-evm: Use card DAPM context to access widgets
ASoC: mop500_ab8500: Use card DAPM context to access widgets
ASoC: wm1133-ev1: Use card DAPM context to access widgets
ASoC: atmel: Improve machine driver compile test coverage
ASoC: atmel: Add dependency to SND_SOC_I2C_AND_SPI where necessary
ALSA: control: Fix a typo of SNDRV_CTL_ELEM_ACCESS_TLV_* with SNDRV_CTL_TLV_OP_*
ALSA: usb-audio: Don't attempt to get Microsoft Lifecam Cinema sample rate
ASoC: rnsd: fix build regression without CONFIG_OF
ALSA: emu10k1: add toggles for E-mu 1010 optical ports
ALSA: ctl: fill identical information to return value when adding userspace elements
ALSA: ctl: fix a bug to return no identical information in info operation for userspace controls
ALSA: ctl: confirm to return all identical information in 'activate' event
...
Here's the big staging driver patchset for 4.1-rc1.
There's a lot of patches here, the Outreachy application period happened
during this development cycle, so that means that there was a lot of
cleanup patches accepted. Other than the normal coding style and sparse
fixes here, there are some driver updates and work toward making some of
the drivers into "mergable" shape (like the Unisys drivers.)
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUsIA0ACgkQMUfUDdst+ylHuACgm8QZ9S6lk45/Qd9YeR3NSDaS
upoAn3gVAaHnuxkW3anivuwOcirgCp3l
=7VHU
-----END PGP SIGNATURE-----
Merge tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging driver patchset for 4.1-rc1.
There's a lot of patches here, the Outreachy application period
happened during this development cycle, so that means that there was a
lot of cleanup patches accepted. Other than the normal coding style
and sparse fixes here, there are some driver updates and work toward
making some of the drivers into "mergable" shape (like the Unisys
drivers.)
All of these have been in linux-next for a while"
* tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1214 commits)
staging: lustre: orthography & coding style
staging: lustre: lnet: lnet: fix error return code
staging: lustre: fix sparse warning
Revert "Staging: sm750fb: Fix C99 Comments"
Staging: rtl8192u: use correct array for debug output
staging: rtl8192e: Remove dead code
staging: rtl8192e: Comment cleanup (style/format)
staging: rtl8192e: Fix indentation in rtllib_rx_auth_resp()
staging: rtl8192e: Decrease nesting of rtllib_rx_auth_resp()
staging: rtl8192e: Divide rtllib_rx_auth()
staging: rtl8192e: Fix PRINTK_WITHOUT_KERN_LEVEL warnings
staging: rtl8192e: Fix DO_WHILE_MACRO_WITH_TRAILING_SEMICOLON warning
staging: rtl8192e: Fix BRACES warning
staging: rtl8192e: Fix LINE_CONTINUATIONS warning
staging: rtl8192e: Fix UNNECESSARY_PARENTHESES warnings
staging: rtl8192e: remove unused EXPORT_SYMBOL_RSL macro
staging: rtl8192e: Fix RETURN_VOID warnings
staging: rtl8192e: Fix UNNECESSARY_ELSE warning
staging: rtl8723au: Remove unneeded comments
staging: rtl8723au: Use __func__ in trace logs
...
Only one framework update this time around, a change from Lars-Peter to
move full to pm_ops and remove the legacy bus PM ops. Otherwise it's
all driver updates:
- Make the spidev driver complain loudly if registered as spidev with
DT rather than with a compatible string, hopefully helping people
avoid making that mistake.
- Error handling and robustness fixes for the Designware and Intel MID
drivers from Andy Shevchenko.
- Substantial performance improvements for the Raspberry Pi driver from
Martin Sperl.
- Several new features for spidev_test from Adrian Remonda and Ian
Abbott.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVK8JoAAoJECTWi3JdVIfQEl0H/iQU06k/sFtfQYwsj/LJHKTe
L3SOfBoEuS3l9UudCpVspGwikcrbdTtziO/VY0oCPMdjovHrXFsaoT902LGeDsTn
oSnxXojSQOpet7at2tEYk7O/tdyykKR6fU2t4GJBYRreBvvQCG8xsrrAk/ahHTsn
LC4x49zwgvm4R24VPA37AhdDvBUxFWuJC3uQhf9cc59/DqPKaC5cm2L6mA6m5Vwk
W7t6kodr8wURp+Yc+VAvR3u4tRkCJUmgSO54ysGNuToR5brRTyEnBCed2GcqoDjQ
OFQDgHuEP/YPQOojxGJ+RMW5VpKXmaXYotvUhTdLRSevVmVNQfa4zUPtTnb13kA=
=+TxD
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Only one framework update this time around, a change from Lars-Peter
to move full to pm_ops and remove the legacy bus PM ops. Otherwise
it's all driver updates:
- make the spidev driver complain loudly if registered as spidev with
DT rather than with a compatible string, hopefully helping people
avoid making that mistake.
- error handling and robustness fixes for the Designware and Intel
MID drivers from Andy Shevchenko.
- substantial performance improvements for the Raspberry Pi driver
from Martin Sperl.
- several new features for spidev_test from Adrian Remonda and Ian
Abbott"
* tag 'spi-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (75 commits)
spi: bcm2835: enabling polling mode for transfers shorter than 30us
spi: bcm2835: transform native-cs to gpio-cs on first spi_setup
spi: img-spfi: Control CS lines with GPIO
spi: img-spfi: Reset controller after each message
spi: img-spfi: Implement a handle_err() callback
spi: img-spfi: Setup TRANSACTION register before CONTROL register
spi: Make master->handle_err() callback optional to avoid crashes
spi: img-spfi: Limit bit clock to 1/4th of input clock
spi: img-spfi: Implement a prepare_message() callback
spi: fsl-dspi: Add ~50ns delay between cs and sck
spi: fsl-dspi: Add cs-sck delays
spi: fsl-dspi: Fix clock rate scale values
spi: signedness bug in qspi_trigger_transfer_out_int()
spi: imx: read back the RX/TX watermark levels earlier
spi: spi-bfin5xx: Initialize cr_width in bfin_spi_pump_transfers()
spi: bitbang: only toggle bitchanges
spi: pxa2xx: missing break in pxa2xx_ssp_get_clk_div()
spi: fsl-dspi: Fix clock rate scale values
spi: Using Trigger number to transmit/receive data
spi: bcm2835: fill FIFO before enabling interrupts to reduce interrupts/message
...
This reverts commit ecc19d1786.
It added a new warning to try to encourage driver writers to set the
device capabities properly, but drivers haven't been updated and in the
meantime it just generaters a scary message that users cannot actually
do anything about.
Warnings like these are appropriate if you actually expect to fix the
code that causes them. They are not appropriate for releases.
Requested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing directions, residue_granularity,
srd_addr_widths and dst_addr_widths bitfields.
Without those we will see a kernel WARN()
when loading musb on am335x devices.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RaidEngine is a new FSL hardware used for Raid5/6 acceration.
This patch enables the RaidEngine functionality and provides
hardware offloading capability for memcpy, xor and pq computation.
It works with async_tx.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This DMAC is Renesas USB high-speed module DMA controller that
supports slave transfer.
This USB-DMAC has similar register sets with R-Car Gen2 DMAC, but
the USB-DMAC has specific registers to control the USB transactions.
If this code is added into the rcar-dmac driver, it will become
unreadable. So, this driver is independent from the rcar-dmac.
And, this USB-DMAC uses virt-dma infrastructure.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The "data" parameter passed indirectly to the edma_callback() should be
edma_chan and not the dma_chan.
This bug was so far harmless since the offset of struct dma_chan within struct
edma_chan is 0. However as soon as someone changes struct edma_chan this would
cause troubles.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The function d40_prep_sg takes the type enum dma_transfer_direction
as second last parameter. However, the memcpy calls pass DMA_NONE
which is of type enum dma_data_direction. Fix this by passing the
actual transfer direction DMA_MEM_TO_MEM.
This does not change the actual code flow since only the transfer
direction DMA_MEM_TO_DEV and DMA_DEV_TO_MEM are actually used in the
function d40_prep_sg.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a driver for the DMA controller found in the Ingenic
JZ4780.
It currently does not implement any support for the programmable firmware
feature of the controller - this is not necessary for most uses. It also
does not take priority into account when allocating channels, it just
allocates the first available channel. This can be implemented later.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
[Updated for dmaengine api changes, Add residue support, couple of minor fixes]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If edma_terminate_all() was called while a transfer was running (i.e. after
edma_execute() but before edma_callback()) the echan->edesc was not freed.
This was due to the fact that a running transfer is on none of the
vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute()
removes it from the desc_issued list), so the vchan_dma_desc_free_list()
called at the end of edma_terminate_all() didn't find it and didn't free it.
This bug was found on an AM1808 based hardware (very similar to da850evm,
however using the second MMC/SD controller), where intense operations on the SD
card wasted the device 128MB RAM within a couple of days.
Peter Ujfalusi:
The issue is even more severe since it affects cyclic (audio) transfers as
well. In this case starting/stopping audio will results memory leak.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Setup the capabilities of the device/driver, so that users of the DMAengine API
can query them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The GFP_ATOMIC is too strict, and DMAEngine documentation make an advice to use
GFP_NOWAIT. This patch does the conversion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are few places where the implemented pieces of code are not needed, i.e.:
- direction can't be wrong in hsu_dma_chan_start()
- desc->active set to 0 by kzalloc
- DMAEngine is NULL-aware when call ->device_alloc_chan_resources()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tangier is known to have the HSU DMA IP as PCI device 00:05.0. The patch
adds the ID as found on Intel Edison board to the PCI device table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the staging tree fixes that are upstream here as well to prevent
merge conflicts from people trying to clean up code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_tx_status() function returns the desc->status if the
dma_cookie_status() call does indicate the cookie completed,
however the desc->status is not look directly compatible. Sparse
throws the following warning:
pl330.c:2262:35: warning: mixing different enum types
pl330.c:2262:35: int enum desc_status versus
pl330.c:2262:35: int enum dma_status
Attempt to fix this by adding a switch statement to turn the
desc->status into a dma_status.
Note, this has only been tested with the dmatest suite.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Whilst running sparse on pl330 driver it was noticed there are
two functions that are not static but not exported to any other
users in the kernel.
Fix the following warnings by making 'pl330_pause' and the
'pl330_get_current_xferred_count' static:
pl330.c:2165:5: warning: symbol 'pl330_pause' was not declared. Should it be static?
pl330.c:2206:5: warning: symbol 'pl330_get_current_xferred_count' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When running Xilinx Zynq in big-endian mode the pl330 driver
fails to pass the dmatest suite. To fix this, ensure all non
byte values are written in little endian.
As a note, the documentation does not mention if it will do
big-endian descriptor fetches, only that it will swap the
data in flight.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Ensure that clients can automatically configure themselves and avoid a
nasty warning at boot by providing capability information.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri on DMAEngine is no longer needed. remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently when version 3.1 of the mx6q SDMA firmware is used we get:
[ 0.392169] imx-sdma 20ec000.sdma: unknown firmware version
[ 0.399281] imx-sdma 20ec000.sdma: initialized
Add support for it.
Based on a patch from Shengjiu Wang from the internal FSL kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the last and the only user of this driver is converted to use dw_dmac we
can remove driver from the tree.
Moreover, besides the driver is unmaintained a long time, it serves for the
DesignWare DMA IP, for which we have already driver in the tree.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the xilinx_dma.h header file
to the include/linux/dma.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Free Software Foundation mailing address has been moved in the past and some
of the addresses here are outdated. Remove them from file headers since the
COPYING file in the kernel sources includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add register offset table entry for the newer (v1.7.0) version of the BAM IP
found on MSM8916. Update the DT bindings documentation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The same error message is printed from different switch cases. Since both of
these jump into same error label we can move error print there and add a DMA
direction in order to make it easier to grep error from sources.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The same error message is printed from different functions. Add a function
name to error message in order to make it easier to grep error from sources.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 9cade1a46c (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com>
Fixes: 9cade1a46c (dma: dw: split driver to library part and platform code)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Below comments got from Page4724 of Reference Manual of i.mx6q:
http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf
--"Static context mode should be used for the first channel called
after reset to ensure that the all context RAM for that channel is
initialized during the context SAVE phase when the channel is
done or yields. Subsequent calls to the same channel or
different channels may use any of the dynamic context modes.
This will ensure that all context locations for the bootload
channel are initialized, and prevent undefined values in context
RAM from being loaded during the context restore if the
channel is re-started later"
Unfortunately, the rule was broken by commit(5b28aa319b)
.This patch just take them back.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the following issues regarding to the calculation of the
residue:
1. The residue is always calculated for the current transfer even if the
cookie is associated to a pending transfer.
2. For scatter/gather DMA the calculation of the residue for the current
transfer doesn't include the bytes of the child descriptors that are already
transferred.
It only calculates the difference between the transfer's total length minus
the number of bytes that are already transferred for the current child
descriptor.
For example: There is a scatter/gather DMA transfer with a total length of
1 MByte. Getting the residue several times while the transfer is running shows
something like that:
1: residue = 975584
2: residue = 1002766
3: residue = 992627
4: residue = 983767
5: residue = 985694
6: residue = 1008094
7: residue = 1009741
8: residue = 1011195
3. The driver stores the residue but never resets it when starting a new
transfer.
For example: If there are two subsequent DMA transfers. The first one with
a total length of 1 MByte and the second one with a total length of 1 kByte.
Getting the residue for both transfers shows something like that:
transfer 1: residue = 975584
transfer 2: residue = 1048380
Changes from V1:
* Fixed coding style of the multi-line comments.
* Improved accuracy of the residue calculation when the transfer for the
first descriptor is active.
Changes from V2:
* Member 'tx_width' of 'struct at_desc' restored, because the transfer width
can't be derived from the source width when using "slave_sg".
The transfer width is needed for the calculation of the residue if either
the transfer of the first or the last descriptor is in progress.
In the case of a "memory_to_memory_sg" transfer (part of this patch
series) the transfer width of both descriptors may differ. Thus it is
required to additionally set 'tx_width' of the last descriptor.
* Added functions for multiply used calculations.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for memory to memory scatter-gather transfers.
Changes from V1:
* Fixed coding style of the multi-line comments.
Changes from V2:
* Added setup of 'desc->tx_width' that is needed to calculate the
residue.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The HSU DMA is developed to support High Speed UART controllers found in
particular on Intel MID platforms such as Intel Medfield.
The existing implementation is tighten to the drivers/tty/serial/mfd.c driver
and has a lot of disadvantages. Besides that we would like to get rid of the
old HS UART driver in regarding to extending the 8250 which supports generic
DMAEngine API. That's why the current driver has been developed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the dmaengine complaint about missing slave caps :
- declare the available bus widths
- declare the available transfer types
- declare the residue calculation type
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove double check on chan->desc.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit 7bced39751 ("net_dma: simple removal") removed the net_dma
support entirely, net_dma_find_channel has no users left. Remove the function
entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Avoid the warning below triggered during dmaengine async device
registration.
WARNING: CPU: 1 PID: 1 at linux/drivers/dma/dmaengine.c:863
dma_async_device_register+0x2a8/0x4b8()
this driver doesn't support generic slave capabilities reporting
To do that fill mandatory .directions bit mask,
.src/dst_addr_widths and .residue_granularity dma_device fields
with appropriate values.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
BDX-DE IOATDMA reports incorrect DMACAP register for PQ related
ops. Ignoring those bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When simplificating the channel configuration, the cyclic case has been
forgotten. It leads to use bad configuration causing many bugs.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When dma controller is not used by any user and set off,
we should disble interrupt handler, at least the interrupt
reset part, for some subsystem, e.g. ADSP, may use the
dma in its own logic, here reset the interrupt may make
this subsystem work abnormally.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Below are the refinements.
1. Set DMA abort bit when disabling dma channel. This will clear
the remaining data in dma FIFO, to fix channel-swap issue.
2. Read DMA HW pointer when updating DMA status. Previously dma
position is calculated by adding one period size in dma interrupt.
This is inaccurate/insufficient for some high-quality audio APP.
Since interrupt bottom half handler has variable schedule delay,
it causes big error when calculating sample delay. Read the actual
HW pointer and feedback can improve the accuracy.
3. Do some minor code clean.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix spelling mistake, "aquire" -> "acquire" and missing newline (as
spotted by Joe Perches.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During system reboot, the sh-dma-engine device may be runtime-suspended,
causing a crash:
Unhandled fault: imprecise external abort (0x1406) at 0x0002c02c
Internal error: : 1406 [#1] SMP ARM
...
PC is at sh_dmae_ctl_stop+0x28/0x64
LR is at sh_dmae_ctl_stop+0x24/0x64
If the sh-dma-engine is runtime-suspended, its module clock is turned
off, and its registers cannot be accessed.
To fix this, move the call to sh_dmae_ctl_stop(), which touches the
DMAOR register, to the sh_dmae_suspend() and sh_dmae_runtime_suspend()
callbacks. This makes PM operations more symmetric, as both
sh_dmae_resume() and sh_dmae_runtime_resume() already call sh_dmae_rst()
to re-initialize the DMAOR register.
Remove sh_dmae_shutdown(), as it became empty.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes checkpatch.pl error in file ste_dma40.c
ERROR: space required before the open parenthesis '('
Signed-off-by: Dilek Uzulmez <dilekuzulmez@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some dma channels may be reserved for other purpose in other layer,
like secure driver in EL2/EL3. PDMA driver can see the interrupt
status, but it should not try to handle related interrupt, since it
doesn't belong to PDMA driver in kernel. These interrupts should be
handled by corresponding client/module.Otherwise, it will overwrite
illegal memory and cause unexpected issues, since pdma driver only
requests resources for pdma channels.
In PDMA driver, the reserved channels are at the end of total 32
channels. If we find interrupt bit index is not smaller than total
dma channels, we should ignore it.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calls tasklet_kill() in error path of the probe function were missing.
Add the same in error path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
in dma_slave_config, which is incompatible with the way that the
dmaengine API normally works.
I've had a closer look at the existing code now and found that all
slave drivers that pass a slave_id in dma_slave_config for SH do that
right after passing the same ID into shdma_chan_filter, so we can just
rely on that. However, the various shdma drivers currently do not
remember the slave ID that was passed into the filter function when
used in non-DT mode and only check the value to find a matching channel,
unlike all other drivers.
There might still be drivers that are not part of the kernel that rely
on setting the slave_id to some other value, so to be on the safe side,
this adds another 'real_slave_id' field to shdma_chan that remembers
the ID and uses it when a driver passes a zero slave_id in dma_slave_config,
like most drivers do.
Eventually, the real_slave_id and slave_id fields should just get merged
into one field, but that requires other changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
DMA_PAUSE command is used for halting DMA transfer on chosen channel.
It can be useful when we want to safely read residue before terminating
all requests on channel. Otherwise there can be situation when some data
is transferred before channel termination but after reading residue,
which obviously results with data loss. To avoid this situation we can
pause channel, read residue and then terminate all requests.
This scenario is common, for example, in serial port drivers.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds possibility to read residue of DMA transfer. It's useful
when we want to know how many bytes have been transferred before we
terminate channel. It can take place, for example, on timeout interrupt.
Signed-off-by: Lukasz Czerwinski <l.czerwinski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A still unconfirmed hardware bug prevents the IPMMU microTLB 0 to be
flushed correctly, resulting in memory corruption. DMAC 0 channel 0 is
connected to microTLB 0 on currently supported platforms, so we can't
use it with the IPMMU. As the IOMMU API operates at the device level we
can't disable it selectively, so ignore channel 0 for now if the device
is part of an IOMMU group.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When descriptor memory is accessed through an IOMMU the DMADAR register
isn't initialized automatically from the first descriptor at beginning
of transfer by the DMAC like it should. Initialize it manually with the
destination address of the first chunk.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When wired to an IOMMU to access data, the DMAC accesses the hardware
descriptors through the IOMMU as well. We're using the DMA mapping API
to allocate the descriptors, but with a NULL device at the moment, which
prevents IOMMU mappings from being created. Fix this by passing the DMAC
device instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The error interrupt handler stops and reinitializes all channels. This
causes a crash for channels that have never been used, as their
descriptor lists are uninitialized. Fix it by initializing the
descriptor lists at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The rcar_dmac_desc_put() function is called in interrupt context and
must thus use spin_lock_irqsave() instead of spin_lock_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch fixes following sparse warnings:
edma.c:537:32: warning: symbol 'edma_prep_dma_memcpy' was not declared. Should it be static?
edma.c:1070:6: warning: symbol 'edma_filter_fn' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The desc variable is used uninitialized in the rcar_dmac_desc_get() and
rcar_dmac_xfer_chunk_get() functions if descriptors need to be
allocated. Fix it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sh_dmae_{suspend|resume}() for the {freeze|
thaw|restore}() PM methods. It's handy to achieve this with SIMPLE_DEV_PM_OPS()
macro; since that macro doesn't do anything when CONFIG_PM_SLEEP is undefined,
we don't need to #define sh_dmae_{suspend|resume} NULL anymore but we'll have to
enclose sh_dmae_{suspend|resume}() into the new #ifdef...
Based on original patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use SET_RUNTIME_PM_OPS() to initialize the runtime PM method pointers in the
'struct dev_pm_ops'; since that macro doesn't do anything if CONFIG_PM is
not defined, we have to move #ifdef up to also cover the runtime PM methods
in order to avoid compilation warnings.
Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently ACPI, PCI and pnp all implement the same resource list
management with different data structure. We need to transfer from
one data structure into another when passing resources from one
subsystem into another subsystem. So move struct resource_list_entry
from ACPI into resource core and rename it as resource_entry,
then it could be reused by different subystems and avoid the data
structure conversion.
Introduce dedicated header file resource_ext.h instead of embedding
it into ioport.h to avoid header file inclusion order issues.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When using FIFO, we need to support differents data width in a single
transfer. For example, serial device which usually uses 1-byte data
width will use 4-bytes data width when using the FIFO. If the transfer
size is not aligned on 4-bytes then the end of the transfer will be
performed with 1-byte data-width. For that reason,
at_xdmac_prep_slave_sg() now builds linked list descriptors using view 2
instead of view 1 so each of them can update the DWIDTH field into the
Channel Configuration Register.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch simplifies the channel configuration register management.
Relying on a "software snapshot" of the configuration is not safe and
too complex.
Multiple dwidths will be introduced for slave transfers. In this case,
it becomes quite difficult to have an accurate snapshot of the channel
configuration register in the way it is done. Using the channel
configuration available in the lli descriptor simplifies this stuff.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When suspending the device, read the channel configuration directly from
the register instead of relying on a software snapshot, it will be
safer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
wait_for_completion_timeout reaching timeout was being ignored,
fail the self-test if timeout condition occurs.
v2: fixup of coding style issues.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The scope of those varsiables is in while-loop. This patch moves them there and
removes duplicate code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simple fixes an indentation in few places across the code.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for the IMG Multi-threaded DMA Controller (MDC) found on
certain IMG SoCs. Currently this driver supports the variant present
on the MIPS-based Pistachio SoC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should unlock here before returning -EINVAL.
Fixes: 39ad460096 ('dmaengine: s3c24xx: Split device_control')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding PCI device IDs and hooks in workarounds for Broadwell DE ioatdma.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
And don't print an error: not configured is not an error.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ecc19d1786
(dmaengine: Add a warning for drivers not using the generic slave
caps retrieval) added WARN() for DMA_SLAVE.
Kernel will shows WARNING without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver doesn't support residue reporting at all.
residue_granularity should be set to DMA_RESIDUE_GRANULARITY_DESCRIPTOR.
Special thanks to Laurent
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Everything uses dmaengine now, so there is no reason to
keep this around any longer. Thanks to everyone who was involved
in moving the users over to use the dmaengine APIs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
A recent patch that removed coh901318_control() replaced it
with a number of pointers to existing functions, but those
unfortunately have the wrong return type and need to be
changed to return an 'int' with an error value rather than
a 'void' to avoid these build warnings:
drivers/dma/coh901318.c:2697:32: warning: assignment from incompatible pointer type
base->dma_slave.device_config = coh901318_dma_set_runtimeconfig;
^
drivers/dma/coh901318.c:2698:31: warning: assignment from incompatible pointer type
base->dma_slave.device_pause = coh901318_pause;
^
drivers/dma/coh901318.c:2699:32: warning: assignment from incompatible pointer type
base->dma_slave.device_resume = coh901318_resume
The coh901318_base_init function has the correct return type
already, but needs to be marked 'static' to avoid a sparse
warning about a missing declaration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6782af118b ("dmaengine: coh901318: Split device_control")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A typo has been introduced in the spin_unlock_irqrestore function. Fix it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sa11x0_dma_resume conflicts between the dmaengine device_resume callback
and the dev_pm_ops resume implementation.
Also remove some unused variables at the same time.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The function is too big to be a static inline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After commit ecc19d1786 ("dmaengine: Add
a warning for drivers not using the generic slave caps retrieval"),
the Tegra APB DMA driver causes this warning during boot:
WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x294/0x538()
this driver doesn't support generic slave capabilities reporting
Fix by setting the appropriate reporting structure fields that are
passed to dma_async_device_register().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the following build warning:
drivers/dma/fsldma.c: In function 'fsl_dma_device_terminate_all':
drivers/dma/fsldma.c:947:6: warning: unused variable 'size' [-Wunused-variable]
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ecc19d1786
(dmaengine: Add a warning for drivers not using the generic slave
caps retrieval) added WARN() for DMA_SLAVE.
Kernel will shows WARNING without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to return a 'fake' value upon platform_get_irq() failure.
Just propagate the real error instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
By using devm functions we can make the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since ecc19d1786 ("dmaengine: Add a warning for drivers not using the
generic slave caps retrieval") the following warning is observed:
[ 0.224981] ------------[ cut here ]------------
[ 0.225013] WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x2a0/0x4c8()
[ 0.225023] this driver doesn't support generic slave capabilities reporting
Declare the slave capabilities to avoid such warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since ecc19d1786 ("dmaengine: Add a warning for drivers not using the
generic slave caps retrieval") the following warning is observed:
[ 0.113023] ------------[ cut here ]------------
[ 0.113053] WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x2a0/0x4c8()
[ 0.113063] this driver doesn't support generic slave capabilities reporting
Declare the slave capabilities to avoid such warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new DMAEngine requirement is to provide what the DMA controller can do,
such as directions, bus widths, and residue granularity. The patch sets those
properties for the DesignWare DMA controller driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of PCI driver we will get a warning:
dw_dmac_pci 0000:00:18.0: Unbalanced pm_runtime_enable!
dw_dmac_pci 0000:00:18.0: DesignWare DMA Controller, 8 channels
This happens due to pm_runtime_enable() call from the driver when PM runtime is
enabled by core.
This patch moves that call to the platform driver where it might make sense.
Fixes: bb32baf76e (dmaengine: dw: enable runtime PM)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In a recent cleanup, the mmp_tdma_terminate_all function was
introduced but does not set a proper return value. Almost
no slave driver uses that return value, but if one does, the
result will be undefined, which the compiler warns about:
dma/mmp_tdma.c: In function 'mmp_tdma_terminate_all':
dma/mmp_tdma.c:474:1: warning: no return statement in function returning non-void [-Wreturn-type]
This changes the driver to return zero, like most other
drivers do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f43a6fd400 ("dmaengine: mmp-tdma: Split device_control")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mmp tdma driver does not actually require this header, and
we want to enable multiplatform support for MMP, which would
make it inaccessible and cause a build error.
This patch just removes the old #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit db08425ebd ("dmaengine: k3: Split device_control") introduced
two new helper functions, which unfortunately have the same names
as the existing suspend/resume functions, resulting in a build error
when CONFIG_PM_SLEEP is enabled:
drivers/dma/k3dma.c:823:12: error: conflicting types for 'k3_dma_resume'
static int k3_dma_resume(struct device *dev)
^
drivers/dma/k3dma.c:625:12: note: previous definition of 'k3_dma_resume' was here
static int k3_dma_resume(struct dma_chan *chan)
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db08425ebd ("dmaengine: k3: Split device_control")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While splitting device control in db08425ebd ("dmaengine: k3:
Split device_control") new function with the same 'k3_dma_resume' name
was added, leading to build error:
drivers/dma/k3dma.c:823:12: error: conflicting types for ‘k3_dma_resume’
drivers/dma/k3dma.c:625:12: note: previous definition of ‘k3_dma_resume’ was here
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the atomic DMA coherent pool is too small, disable use of hardware
descriptor lists instead of crashing the system:
ERROR: 256 KiB atomic DMA coherent pool is too small!
Please increase it with coherent_pool= kernel parameter!
Unable to handle kernel NULL pointer dereference at virtual address 00000004
Internal error: Oops: a07 [#1] PREEMPT SMP ARM
PC is at rcar_dmac_chan_reinit+0x3c/0x160
LR is at _raw_spin_lock_irqsave+0x18/0x5c
[<802132c0>] (rcar_dmac_chan_reinit) from [<80214818>] (rcar_dmac_isr_error+0x84/0xa0)
[<80214818>] (rcar_dmac_isr_error) from [<80060484>] (handle_irq_event_percpu+0x50/0x150)
[<80060484>] (handle_irq_event_percpu) from [<800605c0>] (handle_irq_event+0x3c/0x5c)
[<800605c0>] (handle_irq_event) from [<8006350c>] (handle_fasteoi_irq+0xb8/0x198)
[<8006350c>] (handle_fasteoi_irq) from [<8005fdb0>] (generic_handle_irq+0x20/0x30)
[<8005fdb0>] (generic_handle_irq) from [<8000fcd0>] (handle_IRQ+0x50/0xc4)
[<8000fcd0>] (handle_IRQ) from [<800092cc>] (gic_handle_irq+0x28/0x5c)
[<800092cc>] (gic_handle_irq) from [<80012700>] (__irq_svc+0x40/0x70)
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Unlike DMA transfers descriptors that are preallocated and cached,
memory used to store hardware descriptors is allocated and freed with
the DMA coherent allocation API for every transfer. Besides degrading
performances, this creates a CMA stress test that seems to cause issues.
Running dmatest with the noverify option produces
[ 50.066539] alloc_contig_range test_pages_isolated(6b845, 6b846) failed
[ 50.235180] alloc_contig_range test_pages_isolated(6b848, 6b84e) failed
[ 52.964584] alloc_contig_range test_pages_isolated(6b847, 6b848) failed
[ 54.127113] alloc_contig_range test_pages_isolated(6b843, 6b844) failed
[ 56.270253] alloc_contig_range test_pages_isolated(6b84c, 6b850) failed
The root cause needs to be fixed, but in the meantime, as a workaround
and a performance improvement, cache hardware descriptors.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The DMAC supports hardware-based auto-configuration from descriptor
lists. This reduces the number of interrupts required for processing a
DMA transfer. Support that mode in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The DMAC is a general purpose multi-channel DMA controller that supports
both slave and memcpy transfers.
The driver currently supports the DMAC found in the r8a7790 and r8a7791
SoCs. Support for compatible DMA controllers (such as the audio DMAC)
will be added later.
Feature-wise, automatic hardware handling of descriptors chains isn't
supported yet. LPAE support is implemented.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Remove the function is_imx21_dma() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/tegra20-apb-dma.c:1428:37: warning: assignment from incompatible pointer type [enabled by default]
drivers/dma/ste_dma40.c: In function 'd40_terminate_all':
The function prototype expects return type 'int' whereas these where void
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/ste_dma40.c:2627:3: warning: 'return' with a value, in function returning void [enabled by default]
drivers/dma/ste_dma40.c: In function 'd40_ops_init':
drivers/dma/ste_dma40.c:2869:28: warning: assignment from incompatible pointer type [enabled by default]
The function prototype expects return type 'int' whereas these where void
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/mxs-dma.c: In function 'mxs_dma_probe':
drivers/dma/mxs-dma.c:848:35: warning: assignment from incompatible pointer type [enabled by default]
drivers/dma/mxs-dma.c:849:36: warning: assignment from incompatible pointer type [enabled by default]
The function prototype expects return type 'int' whereas these where void
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mxs_dma_reset_chan() expects struct dma_chan * as argument but we were
providing struct dma_chan, so fix this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For the slave caps retrieval to be really useful, most drivers need to
implement it.
Hence, we need to be slightly more aggressive, and trigger a warning at
registration time for drivers that don't fill their caps infos in order to
encourage them to implement it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename the device_control callback of the TXX9 DMA driver to terminate_all
since it's all it's really doing. That will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename the device_control callback of the Timberdal DMA driver to terminate_all
since it's all it's really doing. That will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename the device_control callback of the Intel PCH DMA driver to terminate_all
since it's all it's really doing. That will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Marvell XOR engine doesn't allow any operations that use to be defined in
device_control, it shouldn't need to be defined. Since it's going to be
deprecated, remove it altogether.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Xilinx VDMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the NVidia Tegra20 APB DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the ST-Ericsson DMA 40 driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Allwinner A31 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the SiRF Prima 2 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Super-H DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the SA-11x0 DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Samsung S3C24xxx DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Qualcomm BAM DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the AMBA PL330 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the TI OMAP DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the NBPF AXI DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale MXS DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale MPC512x DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale Elo DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
While we're at it, remove the useless prep_sg callback.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Moxart DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Marvell MMP TDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Marvell MMP PDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Hisilicon K3 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the IPU IDMAC driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Intel MID DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale IMX SDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi