On SuperH, the base of the physical memory might be different from
zero. In this case, PCI address zero will map to a non-zero physical
address. In order to make sure that the DMA mapping API takes care of
this DMA offset, we must fill in the dev->dma_pfn_offset field for PCI
devices. This gets done in the pcibios_bus_add_device() hook, called
for each new PCI device detected.
The dma_pfn_offset global variable is re-calculated for every PCI
controller available on the platform, but that's not an issue because
its value will each time be exactly the same, as it only depends on
the memory start address and memory size.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The code setting up the PCI -> SuperHighway mapping doesn't take into
account the fact that the address stored in PCIELARx must be aligned
with the size stored in PCIELAMRx.
For example, when your physical memory starts at 0x0800_0000 (128 MB),
a size of 64 MB or 128 MB is fine. However, if you have 256 MB of
memory, it doesn't work because the base address is not aligned on the
size.
In such situation, we have to round down the base address to make sure
it is aligned on the size of the area. For for a 0x0800_0000 base
address with 256 MB of memory, we will round down to 0x0, and extend
the size of the mapping to 512 MB.
This allows the mapping to work on platforms that have 256 MB of
RAM. The current setup would only work with 128 MB of RAM or less.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The current definition of the PCIe IO and MEM resources for SH7786
doesn't match what the datasheet says. For example, for PCIe0
0xfe100000 is advertised by the datasheet as a PCI IO region, while
0xfd000000 is advertised as a PCI MEM region. The code currently
inverts the two.
The SH4A_PCIEPARL and SH4A_PCIEPTCTLR registers allow to define the
base address and role of the different regions (including whether it's
a MEM or IO region). However, practical experience on a SH7786 shows
that if 0xfe100000 is used for LEL and 0xfd000000 for IO, a PCIe
device using two MEM BARs cannot be accessed at all. Simply using
0xfe100000 for IO and 0xfd000000 for MEM makes the PCIe device
accessible.
It is very likely that this was never seen because there are two other
PCI MEM region listed in the resources. However, for different
reasons, none of the two other MEM regions are usable on the specific
SH7786 platform the problem was encountered. Therefore, the last MEM
region at 0xfe100000 was used to place the BARs, making the device
non-functional.
This commit therefore adjusts those PCI MEM and IO resources
definitions so that they match what the datasheet says. They have only
been tested with PCIe 0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Depending on the physical memory layout, some PCI MEM areas are not
usable. According to the SH7786 datasheet, the PCI MEM area from
1000_0000 to 13FF_FFFF is only usable if the physical memory layout
(in MMSELR) is 1, 2, 5 or 6. In all other configurations, this PCI MEM
area is not usable (because it overlaps with DRAM).
Therefore, this commit adjusts the PCI SH7786 initialization to mark
the relevant PCI resource as IORESOURCE_DISABLED if we can't use it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Some PCI MEM resources are marked as IORESOURCE_MEM_32BIT, which means
they are only usable when the SH core runs in 32-bit mode. In 29-bit
mode, such memory regions are not usable.
The existing code for SH7786 properly skips such regions when
configuring the PCIe controller registers. However, because such
regions are still described in the resource array, the
pcibios_scanbus() function in the SuperH pci.c will register them to
the PCI core. Due to this, the PCI core will allocate MEM areas from
this resource, and assign BARs pointing to this area, even though it's
unusable.
In order to prevent this from happening, we mark such regions as
IORESOURCE_DISABLED, which tells the SuperH pci.c pcibios_scanbus()
function to skip them.
Note that we separate marking the region as disabled from skipping it,
because other regions will be marked as disabled in follow-up patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
In pcibios_scanbus(), we provide to the PCI core the usable MEM and IO
regions using pci_add_resource_offset(). We travel through all
resources available in the "struct pci_channel".
Also, in register_pci_controller(), we travel through all resources to
request them, making sure they don't conflict with already requested
resources.
However, some resources may be disabled, in which case they should not
be requested nor provided to the PCI core.
In the current situation, none of the resources are disabled. However,
follow-up patches in this series will make some resources disabled,
making this preliminary change necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Some devices may have a non-zero DMA offset, i.e an offset between the
DMA address and the physical address. Such an offset can be encoded
into the dma_pfn_offset field of "struct device", but the SuperH
implementation of the DMA mapping API does not observe this
information.
This commit fixes that by ensuring the DMA address is properly
calculated depending on this DMA offset.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The SH7786 has different physical memory layout configurations,
configurable through the MMSELR register. The configuration is
typically defined by the bootloader, so Linux generally doesn't care.
Except that depending on the configuration, some PCI MEM areas may or
may not be available. This commit adds a helper function that allows
to retrieve the current physical memory layout configuration. It will
be used in a following patch to exclude unusable PCI MEM areas during
the PCI initialization.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.
Signed-off-by: Rich Felker <dalias@libc.org>
unflatten_device_tree() makes use of memblock allocation, and
therefore must be called before paging_init() migrates the memblock
allocation data to the bootmem framework. Otherwise the record of the
allocation for the expanded device tree will be lost, and will
eventually be clobbered when allocated for another use.
Signed-off-by: Rich Felker <dalias@libc.org>
Commit 00b73d8d1b ("sh: add working futex atomic ops on userspace
addresses for smp") changed the futex_atomic_op_inuser function to
use a loop. In case of the FUTEX_OP_SET op with a userspace address
containing a value different of 0, this loop is an endless loop.
Fix that by loading the value of oldval from the userspace before doing
the cmpxchg op, also for the FUTEX_OP_SET case.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rich Felker <dalias@libc.org>
- Add a PX quirk for radeon
- Fix flickering and stability issues with DC on some platforms
- Fix HDMI audio regression
- Few other misc DC and base driver fixes
* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/amd/display: disable CRTCs with NULL FB on their primary plane (V2)"
Revert "drm/amd/display: fix dereferencing possible ERR_PTR()"
drm/amd/display: Fix regamma not affecting full-intensity color values
drm/amd/display: Fix FBC text console corruption
drm/amd/display: Only register backlight device if embedded panel connected
drm/amd/display: fix brightness level after resume from suspend
drm/amd/display: HDMI has no sound after Panel power off/on
drm/amdgpu: add MP1 and THM hw ip base reg offset
drm/amdgpu: fix null pointer panic with direct fw loading on gpu reset
drm/radeon: add PX quirk for Asus K73TK
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlrOFYwACgkQlvcN/ahK
Bwo3twf/ata4Er+pwcYWGM2U7QMPIeBjqyPuuVx/I2bxTvRfdZ0eCiqdXXiY1flf
cKG6PIFxkLl6ypuFGlBXKbt+XX3ReRpNpKro3GUIh1tNarklKwTzGOoyeDBNixUZ
JIdI/StDHSFzfq119jl58S0cWAhuT5CjEPjeiYQX03dwxv57+/XJQlfncsy2qSUH
SVDkgueeYmbSsRm3C3Qcz6pCVJs3LozufzAz75cU2C/+hN5jDRPx3UBKgxXA3sSV
yfPw0gsBEzc0F9xl3LexL8phuwr4GZVsCsWD8AR7VRuq6OFMOkdvU/c1Axkex6xi
9yZiLmN6Wn5epffAKgdLUF7KzPRL2A==
=QiL0
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2018-04-11' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
omap: Fix crash on AM4 EVM, and all OMAP2/3 boards (Tomi)
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
* tag 'drm-misc-next-fixes-2018-04-11' of git://anongit.freedesktop.org/drm/drm-misc:
drm/omap: fix crash if there's no video PLL
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
and get rid of some get_rfc1002_length() in smb2
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
SMB3.11 crypto and hash contexts were not being checked strictly enough.
Add parsing and validity checking for the security contexts in the SMB3.11
negotiate response.
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
The length checking for SMB3.11 negotiate request includes
"negotiate contexts" which caused a buffer validation problem
and a confusing warning message on SMB3.11 mount e.g.:
SMB2 server sent bad RFC1001 len 236 not 170
Fix the length checking for SMB3.11 negotiate to account for
the new negotiate context so that we don't log a warning on
SMB3.11 mount by default but do log warnings if lengths returned
by the server are incorrect.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
- Cleanup unnecessary function call parameters
- Fix a use-after-free bug when aborting logging intents
- Refactor filestreams state data to avoid use-after-free bug
- Fix incorrect removal of cow extents when truncating extended
attributes.
- Refactor open-coded __set_page_dirty in favor of using vfs function.
- Fix a deadlock when fstrim and fs shutdown race.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCgAGBQJazZ/HAAoJEPh/dxk0SrTrGeYP/Asis7MZ3TWfzsPHwK6EoH+w
q1VnKVMqjSRnE8DYmx8w3tMqny2qg9klLkT1SRRz9Htr5CER5XqIX6ZYlQpVKx2R
ycS+I1l/V/kqEmAgDgSK3DZ5uMgKHfo0w7GbKFDg69YDztN3yNBpDfUZ4VqA/Ua2
ADaeMYkJh6oBB5yZAWGyAJEM5TieqQppqyc+WLhbORyjEFreUTTmLqbzLPnceSih
rQLg0noDwZK0XqbwndYXGTNKKoQtiJalnZP18DhH4zOr+FH03i/gmlU3w+ANl3eX
IEE0TR2EkNHLZeduz7xT7ZHUOo0TaGObBK8CJFSojibQ/HooVjLcFQResd3q0coN
WTkbTuxHwMqk2IujKRTqli/saENhvFrOrm/nYTFPw9+3GpRt0iLrXPSBbeMjmsZG
XntdimPEHywjYrdW10VRH+6E6tvQiC/tl3abBuXdaEOJs1KZmPYNt42EF0ZQ5Xs5
IeDOhPLuuyUwRf12RVA9WS6xGdMR0+foMqncXZNcAzxQeAVfUNEtASNMTNIOO2H5
xD34/1ooFJnwT755VLT9U/qUd5CHtWO3AkH+9RVCpKWTaEOSY+gV6ZgmINv9npur
Vw2xnZwxysegVlu76uct/b/sy/8J3OKYIoSYwbt6Zxi0M1WF9zanJ9pKCsBYdL6A
xWoMr0X1yFGcYJozqwJU
=uGz0
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.17-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull more xfs updates from Darrick Wong:
"Most of these are code cleanups, but there are a couple of notable
use-after-free bug fixes.
This series has been run through a full xfstests run over the week and
through a quick xfstests run against this morning's master, with no
major failures reported.
- clean up unnecessary function call parameters
- fix a use-after-free bug when aborting logging intents
- refactor filestreams state data to avoid use-after-free bug
- fix incorrect removal of cow extents when truncating extended
attributes.
- refactor open-coded __set_page_dirty in favor of using vfs
function.
- fix a deadlock when fstrim and fs shutdown race"
* tag 'xfs-4.17-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
Force log to disk before reading the AGF during a fstrim
Export __set_page_dirty
xfs: only cancel cow blocks when truncating the data fork
xfs: non-scrub - remove unused function parameters
xfs: remove filestream item xfs_inode reference
xfs: fix intent use-after-free on abort
xfs: Remove "committed" argument of xfs_dir_ialloc
merge window while it's still open.
1. The first patch adds a new function to lockref: lockref_put_not_zero
2. The second patch fixes GFS2's glock dump code so it uses the new lockref
function. This fixes a problem whereby lock dumps could miss glocks.
3. I made a minor patch to update some comments and fix the lock ordering
text in our gfs2-glocks.txt Documentation file.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaz6pdAAoJENeLYdPf93o71wMH/0cEo34xWiScRM07EgLmZZ3q
YXMvpTvrwK+9i2u8anxiX1smezHeS+7jPrYOG8AGu3IZvKYGTDOwoIY9pxESy5gs
1Rf60s6pPE/dkTSqPaNNuBxPrM1yVyRWOPx04LxC5BCXhsS/6U2RS9ElxGDe7Nyq
P66z1wfm63+erDR7mKSuOL3Ejtglj2EPcrAupaBlRS0wjdUQ9ORyrZBpT6JMOWqd
HWjchrzWVAqx+iyLHlKZjTyPHsPaUBaj1fuv/Vcgu5sJmEJ9mF4s/GQTdwIzi8ip
ByD7MfilyrT7dxRm1uw8OJ7TvqNeaCtxsyNGGBOlSx81s/pk5Vhs8bevnczNvi8=
=jWsi
-----END PGP SIGNATURE-----
Merge tag 'gfs2-4.17.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull more gfs2 updates from Bob Peterson:
"We decided to request the latest three patches to be merged into this
merge window while it's still open.
- The first patch adds a new function to lockref:
lockref_put_not_zero
- The second patch fixes GFS2's glock dump code so it uses the new
lockref function. This fixes a problem whereby lock dumps could
miss glocks.
- I made a minor patch to update some comments and fix the lock
ordering text in our gfs2-glocks.txt Documentation file"
* tag 'gfs2-4.17.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
GFS2: Minor improvements to comments and documentation
gfs2: Stop using rhashtable_walk_peek
lockref: Add lockref_put_not_zero
Stable bugfixes:
- xprtrdma: Fix corner cases when handling device removal # v4.12+
- xprtrdma: Fix latency regression on NUMA NFS/RDMA clients # v4.15+
Features:
- New sunrpc tracepoint for RPC pings
- Finer grained NFSv4 attribute checking
- Don't unnecessarily return NFS v4 delegations
Other bugfixes and cleanups:
- Several other small NFSoRDMA cleanups
- Improvements to the sunrpc RTT measurements
- A few sunrpc tracepoint cleanups
- Various fixes for NFS v4 lock notifications
- Various sunrpc and NFS v4 XDR encoding cleanups
- Switch to the ida_simple API
- Fix NFSv4.1 exclusive create
- Forget acl cache after setattr operation
- Don't advance the nfs_entry readdir cookie if xdr decoding fails
-----BEGIN PGP SIGNATURE-----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=IlWo
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"Stable bugfixes:
- xprtrdma: Fix corner cases when handling device removal # v4.12+
- xprtrdma: Fix latency regression on NUMA NFS/RDMA clients # v4.15+
Features:
- New sunrpc tracepoint for RPC pings
- Finer grained NFSv4 attribute checking
- Don't unnecessarily return NFS v4 delegations
Other bugfixes and cleanups:
- Several other small NFSoRDMA cleanups
- Improvements to the sunrpc RTT measurements
- A few sunrpc tracepoint cleanups
- Various fixes for NFS v4 lock notifications
- Various sunrpc and NFS v4 XDR encoding cleanups
- Switch to the ida_simple API
- Fix NFSv4.1 exclusive create
- Forget acl cache after setattr operation
- Don't advance the nfs_entry readdir cookie if xdr decoding fails"
* tag 'nfs-for-4.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (47 commits)
NFS: advance nfs_entry cookie only after decoding completes successfully
NFSv3/acl: forget acl cache after setattr
NFSv4.1: Fix exclusive create
NFSv4: Declare the size up to date after it was set.
nfs: Use ida_simple API
NFSv4: Fix the nfs_inode_set_delegation() arguments
NFSv4: Clean up CB_GETATTR encoding
NFSv4: Don't ask for attributes when ACCESS is protected by a delegation
NFSv4: Add a helper to encode/decode struct timespec
NFSv4: Clean up encode_attrs
NFSv4; Clean up XDR encoding of type bitmap4
NFSv4: Allow GFP_NOIO sleeps in decode_attr_owner/decode_attr_group
SUNRPC: Add a helper for encoding opaque data inline
SUNRPC: Add helpers for decoding opaque and string types
NFSv4: Ignore change attribute invalidations if we hold a delegation
NFS: More fine grained attribute tracking
NFS: Don't force unnecessary cache invalidation in nfs_update_inode()
NFS: Don't redirty the attribute cache in nfs_wcc_update_inode()
NFS: Don't force a revalidation of all attributes if change is missing
NFS: Convert NFS_INO_INVALID flags to unsigned long
...
Pull vfs thaw updates from Al Viro:
"An ancient series that has fallen through the cracks in the previous
cycle"
* 'work.thaw' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
buffer.c: call thaw_super during emergency thaw
vfs: factor sb iteration out of do_emergency_remount
This seems to cause flickering and lock-ups for a wide range of users.
Revert until we've found a proper fix for the flickering and lock-ups.
This reverts commit 36cc549d59.
Cc: Shirish S <shirish.s@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull AFS updates from Al Viro:
"The AFS series posted by dhowells depended upon lookup_one_len()
rework; now that prereq is in the mainline, that series had been
rebased on top of it and got some exposure and testing..."
* 'afs-dh' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Do better accretion of small writes on newly created content
afs: Add stats for data transfer operations
afs: Trace protocol errors
afs: Locally edit directory data for mkdir/create/unlink/...
afs: Adjust the directory XDR structures
afs: Split the directory content defs into a header
afs: Fix directory handling
afs: Split the dynroot stuff out and give it its own ops tables
afs: Keep track of invalid-before version for dentry coherency
afs: Rearrange status mapping
afs: Make it possible to get the data version in readpage
afs: Init inode before accessing cache
afs: Introduce a statistics proc file
afs: Dump bad status record
afs: Implement @cell substitution handling
afs: Implement @sys substitution handling
afs: Prospectively look up extra files when doing a single lookup
afs: Don't over-increment the cell usage count when pinning it
afs: Fix checker warnings
vfs: Remove the const from dir_context::actor
This reverts commit cd2d6c92a8.
Cc: Shirish S <shirish.s@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hardware understands the regamma LUT as a piecewise linear function,
with points spaced exponentially along the range. We previously
programmed the LUT for range [2^-10, 2^0). This causes (normalized)
color values of 1 (=2^0) to miss the programmed LUT, and fall onto the
end region.
For DCE, the end region is extrapolated using a single (base, slope)
pair, using the max y-value from the last point in the curve as base.
This presents a problem, since this value affects all three color
channels. Scaling down the intensity of say - the blue regamma curve -
will not affect it's end region. This is especially noticiable when
using RedShift. It scales down the blue and green channels, but leaves
full-intensity colors unshifted.
Therefore, extend the range to cover [2^-10, 2^1) by programming another
hardware segment, containing only one point. That way, we won't be
hitting the end region.
Note that things are a bit different for DCN, since the end region can
be set per-channel.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull networking fixes from David Miller:
1) In ip_gre tunnel, handle the conflict between TUNNEL_{SEQ,CSUM} and
GSO/LLTX properly. From Sabrina Dubroca.
2) Stop properly on error in lan78xx_read_otp(), from Phil Elwell.
3) Don't uncompress in slip before rstate is initialized, from Tejaswi
Tanikella.
4) When using 1.x firmware on aquantia, issue a deinit before we
hardware reset the chip, otherwise we break dirty wake WOL. From
Igor Russkikh.
5) Correct log check in vhost_vq_access_ok(), from Stefan Hajnoczi.
6) Fix ethtool -x crashes in bnxt_en, from Michael Chan.
7) Fix races in l2tp tunnel creation and duplicate tunnel detection,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
l2tp: fix race in duplicate tunnel detection
l2tp: fix races in tunnel creation
tun: send netlink notification when the device is modified
tun: set the flags before registering the netdevice
lan78xx: Don't reset the interface on open
bnxt_en: Fix NULL pointer dereference at bnxt_free_irq().
bnxt_en: Need to include RDMA rings in bnxt_check_rings().
bnxt_en: Support max-mtu with VF-reps
bnxt_en: Ignore src port field in decap filter nodes
bnxt_en: do not allow wildcard matches for L2 flows
bnxt_en: Fix ethtool -x crash when device is down.
vhost: return bool from *_access_ok() functions
vhost: fix vhost_vq_access_ok() log check
vhost: Fix vhost_copy_to_user()
net: aquantia: oops when shutdown on already stopped device
net: aquantia: Regression on reset with 1.x firmware
cdc_ether: flag the Cinterion AHS8 modem by gemalto as WWAN
slip: Check if rstate is initialized before uncompressing
lan78xx: Avoid spurious kevent 4 "error"
lan78xx: Correctly indicate invalid OTP
...
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEhRJncuj2BJSl0Jf3sN6d1ii/Ey8FAlrPnM8ACgkQsN6d1ii/
Ey9Kzwf/eQVb6zzn7FDHAb6pLaZ5i2xi2xohsKmhAVQIEa94rZ3mLoRegtnIfyjO
RcjjSAzHSZO9NQgNA2ALdu6bBdzu4/ywQEQCnY2Gqxp0ocG/+k3p/FqLHZGdcqPo
e3gpcVxHSFWUCCGm1t3umI25driqrUq4xa6UFi2IB4djDvTrK/JsSygKx6GiVujL
2eV7v7rgqaaVZQyo8iOd+LlWuKZewKLfnALUDC21X5J2HmvfoyTdn85kldzbiIsG
YR7mcfgAtAVTyCfgXI3eqAGpRFEyqR4ga87oahdV3/iW+4wreh4hm2Xd/IETXklv
Epxyet8IlMB9886PuZhZqgnW6o1RDA==
=z3bP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"A few fixes of Xen related core code and drivers"
* tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: Indicate XENFEAT_linux_rsdp_unrestricted to Xen
xen/acpi: off by one in read_acpi_id()
xen/acpi: upload _PSD info for non Dom0 CPUs too
x86/xen: Delay get_cpu_cap until stack canary is established
xen: xenbus_dev_frontend: Verify body of XS_TRANSACTION_END
xen: xenbus: Catch closing of non existent transactions
xen: xenbus_dev_frontend: Fix XS_TRANSACTION_END handling
-----BEGIN PGP SIGNATURE-----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=l30v
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.17-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
"Fix for one swiotlb regression in 2.16 from Takashi"
* tag 'dma-mapping-4.17-2' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix unexpected swiotlb_alloc_coherent failures
* minor regression test cleanup
* formatting fixes for end user use of kdb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zz/y
-----END PGP SIGNATURE-----
Merge tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kdb updates from Jason Wessel:
- fix 2032 time access issues and new compiler warnings
- minor regression test cleanup
- formatting fixes for end user use of kdb
* tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: use memmove instead of overlapping memcpy
kdb: use ktime_get_mono_fast_ns() instead of ktime_get_ts()
kdb: bl: don't use tab character in output
kdb: drop newline in unknown command output
kdb: make "mdr" command repeat
kdb: use __ktime_get_real_seconds instead of __current_kernel_time
misc: kgdbts: Display progress of asynchronous tests
- Use generic pci_mmap_resoruce_range()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlrMWo4ACgkQykllyylKDCGrrQCfZHss5ank6e1H+EApm0KqEQFu
kbwAoIj6TdCVMH44kJwqtraIhBXV9dhX
=vYT3
-----END PGP SIGNATURE-----
Merge tag 'microblaze-4.17-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze updates from Michal Simek:
"Use generic pci_mmap_resource_range()"
* tag 'microblaze-4.17-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Use generic pci_mmap_resource_range()
microblaze: Provide pgprot_device/writecombine macros for nommu
This patch simply fixes some comments and the gfs2-glocks.txt file:
Places where i_rwsem was called i_mutex, and adding i_rw_mutex.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Function rhashtable_walk_peek is problematic because there is no
guarantee that the glock previously returned still exists; when that key
is deleted, rhashtable_walk_peek can end up returning a different key,
which will cause an inconsistent glock dump. Fix this by keeping track
of the current glock in the seq file iterator functions instead.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Put a lockref unless the lockref is dead or its count would become zero.
This is the same as lockref_put_or_lock except that the lock is never
left held.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
I have one regression fix for a minor build problem after the architecture
removal series, plus a rework of the barriers in the readl/writel
functions, thanks to work by Sinan Kaya:
This started from a discussion on the linuxpcc and rdma mailing lists
[1]. To summarize, we decided that architectures are responsible to
serialize readl() and writel() accesses on a device MMIO space relative
to DMA performed by that device.
This series provides a pessimistic implementation of that behavior for
asm-generic/io.h, which is in turn used by a number of architectures
(h8300, microblaze, nios2, openrisc, s390, sparc, um, unicore32, and
xtensa). Some of those presumably need no extra barriers, or something
weaker than rmb()/wmb(), and they are advised to override the new default
for better performance.
For inb()/outb(), the same barriers are used, but architectures might
want to add another barrier to outb() here if that can guarantee
non-posted behavior (some architectures can, others cannot do that).
The readl_relaxed()/writel_relaxed() family of functions retains the
existing behavior with no extra barriers.
[1]: https://lists.ozlabs.org/pipermail/linuxppc-dev/2018-March/170481.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oBQh
-----END PGP SIGNATURE-----
Merge tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"I have one regression fix for a minor build problem after the
architecture removal series, plus a rework of the barriers in the
readl/writel functions, thanks to work by Sinan Kaya:
This started from a discussion on the linuxpcc and rdma mailing
lists[1]. To summarize, we decided that architectures are responsible
to serialize readl() and writel() accesses on a device MMIO space
relative to DMA performed by that device.
This series provides a pessimistic implementation of that behavior for
asm-generic/io.h, which is in turn used by a number of architectures
(h8300, microblaze, nios2, openrisc, s390, sparc, um, unicore32, and
xtensa). Some of those presumably need no extra barriers, or something
weaker than rmb()/wmb(), and they are advised to override the new
default for better performance.
For inb()/outb(), the same barriers are used, but architectures might
want to add another barrier to outb() here if that can guarantee
non-posted behavior (some architectures can, others cannot do that).
The readl_relaxed()/writel_relaxed() family of functions retains the
existing behavior with no extra barriers"
[1] https://lists.ozlabs.org/pipermail/linuxppc-dev/2018-March/170481.html
* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
io: change writeX_relaxed() to remove barriers
io: change readX_relaxed() to remove barriers
dts: remove cris & metag dts hard link file
io: change inX() to have their own IO barrier overrides
io: change outX() to have their own IO barrier overrides
io: define stronger ordering for the default writeX() implementation
io: define stronger ordering for the default readX() implementation
io: define several IO & PIO barrier types for the asm-generic version
The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.
The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.
The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted. When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.
Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests. As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.e>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 42de82a8b5 previously attempted to fix this, and it did
correctly pad the MN and FR fields with spaces, but the SN field still
contains 0 bytes. The current code fills out the first 16 bytes with
hex2bin, leaving the last 4 bytes zeroed. Rather than adding a lot of
error-prone math to avoid overwriting SN twice, just set the whole thing
to spaces up front (it's only 20 bytes).
Fixes: 42de82a8b5 ("nvmet: don't report 0-bytes in serial number")
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also add error flow in case srcu initialization function fails.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have to increment the number of logical blocks to a 1's based value
in the native format prior to converting to 512b units.
Signed-off-by: Rodrigo R. Galvao <rosattig@linux.vnet.ibm.com>
[changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The admin and first IO queues shared the first irq vector, which has an
affinity mask including cpu0. If a system allows cpu0 to be offlined,
the admin queue may not be usable if no other CPUs in the affinity mask
are online. This is a problem since unlike IO queues, there is only
one admin queue that always needs to be usable.
To fix, this patch allocates one pre_vector for the admin queue that
is assigned all CPUs, so will always be accessible. The IO queues are
assigned the remaining managed vectors.
In case a controller has only one interrupt vector available, the admin
and IO queues will share the pre_vector with all CPUs assigned.
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All the queue memory is allocated up front. We don't take the node
into consideration when creating queues anymore, so removing the unused
parameter.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
User reported controller always retains CSTS.RDY to 1, which fails
controller disabling when resetting the controller. This is also before
the admin queue is allocated, and trying to disable an unallocated queue
results in a NULL dereference.
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvmet_execute_get_disc_log_page() passes a fixed-length string into
nvmet_format_discovery_entry(), which then does a longer memcpy() on
it, as pointed out by gcc-8:
In function 'nvmet_format_discovery_entry',
inlined from 'nvmet_execute_get_disc_log_page' at drivers/nvme/target/discovery.c:126:4:
drivers/nvme/target/discovery.c:62:2: error: 'memcpy' forming offset [38, 223] is out of the bounds [0, 37] [-Werror=array-bounds]
memcpy(e->subnqn, subsys_nqn, NVMF_NQN_SIZE);
Using strncpy() will make this well-defined, filling the rest of the
buffer with zeroes, under the assumption that the input is either
a NUL-terminated string, or a byte sequence containing no zeroes.
If the input is a string that is longer than NVMF_NQN_SIZE, we
continue to have no NUL-termination in the output.
Fixes: a07b4970f4 ("nvmet: add a generic NVMe target")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe over Fabrics 1.0 Section 5.2 "Discovery Controller Properties and
Command Support" Figure 31 "Discovery Controller – Admin Commands"
explicitly listst all commands but "Get Log Page" and "Identify" as
reserved, but NetApp report the Linux host is sending Keep Alive
commands to the discovery controller, which is a violation of the
Spec.
We're already checking for discovery controllers when configuring the
keep alive timeout but when creating a discovery controller we're not
hard wiring the keep alive timeout to 0 and thus remain on
NVME_DEFAULT_KATO for the discovery controller.
This can be easily remproduced when issuing a direct connect to the
discovery susbsystem using:
'nvme connect [...] --nqn=nqn.2014-08.org.nvmexpress.discovery'
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 07bfcd09a2 ("nvme-fabrics: add a generic NVMe over Fabrics library")
Reported-by: Martin George <marting@netapp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme_start_keep_alive() isn't used outside core.c so unexport it and
make it static.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When nvmet_req_init() fails, __nvmet_req_complete() is called
to handle the target request via .queue_response(), so
nvme_loop_queue_response() shouldn't be called again for
handling the failure.
This patch fixes this case by the following way:
- move blk_mq_start_request() before nvmet_req_init(), so
nvme_loop_queue_response() may work well to complete this
host request
- don't call nvme_cleanup_cmd() which is done in nvme_loop_complete_rq()
- don't call nvme_loop_queue_response() which is done via
.queue_response()
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[trimmed changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Compiling on 32 bits system produces a warning for the shift width
when shifting 32 bit integer with 64bit integer.
Make sure that offset always is 64bit, and use macros for retrieving
lower and upper bits of the offset.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
