virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after restore returns, virtio block violated
this rule on restore by restarting queues, which might in theory
cause the VQ to be used directly within restore.
To fix, call virtio_device_ready before using starting queues.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We currently kick event within virtscsi_init,
before host is fully initialized.
This can in theory confuse guest if device
consumes the buffers immediately.
To fix, move virtscsi_kick_event_all out to scan/restore.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In the extremely unlikely event that driver initialization fails after
RX buffers are added, virtio net frees RX buffers while VQs are
still active, potentially causing device to use a freed buffer.
To fix, reset device first - same as we do on device removal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, but virtio 9p device
adds self to channel list within probe, at which point VQ can be
used in violation of the spec.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, virtio console violated this
rule by adding inbufs, which causes the VQ to be used directly within
probe.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, virtio block violated this
rule by calling add_disk, which causes the VQ to be used directly within
probe.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, virtio net violated this
rule by using receive VQs within probe.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec 0.9.X requires DRIVER_OK to be set before
VQs are used, but some drivers use VQs before probe
function returns.
Since DRIVER_OK is set after probe, this violates the spec.
Even though under virtio 1.0 transitional devices support this
behaviour, we want to make it possible for those early callers to become
spec compliant and eventually support non-transitional devices.
Add API for drivers to call before using VQs.
Sets DRIVER_OK internally.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
goto done;
done:
return;
is ugly, it was put there to make diff review easier.
replace by open-coded return.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
config_mutex served two purposes: prevent multiple concurrent config
change handlers, and synchronize access to config_enable flag.
Since commit dbf2576e37
workqueue: make all workqueues non-reentrant
all workqueues are non-reentrant, and config_enable
is now gone.
Get rid of the unnecessary lock.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now that virtio core ensures config changes don't arrive during probing,
drop config_enable flag in virtio net.
On removal, flush is now sufficient to guarantee that no change work is
queued.
This help simplify the driver, and will allow setting DRIVER_OK earlier
without losing config change notifications.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
config_mutex served two purposes: prevent multiple concurrent config
change handlers, and synchronize access to config_enable flag.
Since commit dbf2576e37
workqueue: make all workqueues non-reentrant
all workqueues are non-reentrant, and config_enable
is now gone.
Get rid of the unnecessary lock.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now that virtio core ensures config changes don't
arrive during probing, drop config_enable flag
in virtio blk.
On removal, flush is now sufficient to guarantee that
no change work is queued.
This help simplify the driver, and will allow
setting DRIVER_OK earlier without losing config
change notifications.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Defer config changed notifications that arrive during
probe/scan/freeze/restore.
This will allow drivers to set DRIVER_OK earlier, without worrying about
racing with config change interrupts.
This change will also benefit old hypervisors (before 2009)
that send interrupts without checking DRIVER_OK: previously,
the callback could race with driver-specific initialization.
This will also help simplify drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (cosmetic changes)
This is in preparation to extending config changed event handling
in core.
Wrapping these in an API also seems to make for a cleaner code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Replace duplicated code in all transports with a single wrapper in
virtio.c.
The only functional change is in virtio_mmio.c: if a buggy device sends
us an interrupt before driver is set, we previously returned IRQ_NONE,
now we return IRQ_HANDLED.
As this must not happen in practice, this does not look like a big deal.
See also commit 3fff0179e3
virtio-pci: do not oops on config change if driver not loaded.
for the original motivation behind the driver check.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
On restore, virtio pci does the following:
+ set features
+ init vqs etc - device can be used at this point!
+ set ACKNOWLEDGE,DRIVER and DRIVER_OK status bits
This is in violation of the virtio spec, which
requires the following order:
- ACKNOWLEDGE
- DRIVER
- init vqs
- DRIVER_OK
This behaviour will break with hypervisors that assume spec compliant
behaviour. It seems like a good idea to have this patch applied to
stable branches to reduce the support butden for the hypervisors.
Cc: stable@vger.kernel.org
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull UDF fixes from Jan Kara:
"Fixes for UDF handling of NFS handles and one fix for proper handling
of corrupted media"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: saner calling conventions for udf_new_inode()
udf: fix the udf_iget() vs. udf_new_inode() races
udf: merge the pieces inserting a new non-directory object into directory
udf: Set i_generation field
udf: Properly detect stale inodes
udf: Make udf_read_inode() and udf_iget() return error
udf: Avoid infinite loop when processing indirect ICBs
udf: Fold udf_fill_inode() into __udf_read_inode()
udf: Avoid dir link count to go negative
Pull cifs/smb3 fixes from Steve French:
"This includes various cifs and smb3 bug fixes including those for bugs
found with the recently updated xfstests.
Also I am working fixes for two additional cifs problems found by
xfstests which I plan to send later (when reviewed and run additional
tests)"
* 'for-next-3.17' of git://git.samba.org/sfrench/cifs-2.6:
Clarify Kconfig help text for CIFS and SMB2/SMB3
CIFS: Fix wrong filename length for SMB2
CIFS: Fix wrong restart readdir for SMB1
CIFS: Fix directory rename error
cifs: No need to send SIGKILL to demux_thread during umount
cifs: Allow directIO read/write during cache=strict
cifs: remove unneeded check of null checking in if condition
cifs: fix a possible use of uninit variable in SMB2_sess_setup
cifs: fix memory leak when password is supplied multiple times
cifs: fix a possible null pointer deref in decode_ascii_ssetup
Trivial whitespace fix
- Fix Kconfig menu structure
- Fix number of syscalls
- Fix compilation warnings from allmodconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlQO4a0ACgkQykllyylKDCE1NACeIFiXdvY7iy4UZyGMTHcdPnH9
o+kAn0v4x8eSaBRXtqYyxMc74US4Qu2N
=3RdC
-----END PGP SIGNATURE-----
Merge tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze
Pull arch/microblaze fixes from Michal Simek:
- Kconfig menu structure fix
- fix number of syscalls
- fix compilation warnings from allmodconfig
* tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix number of syscalls
microblaze: Rename Advance setup to Kernel features
microblaze: Add mm/Kconfig to advance menu
arch/microblaze/include/asm/uaccess.h: Use pr_devel() instead of pr_debug()
arch/microblaze/include/asm/entry.h: Include "linux/linkage.h" to avoid compiling issue
When DYNAMIC_DEBUG enabled, pr_debug() depends on KBUILD_MODNAME which
also depends on the modules number in Makefile. The related information
in "scripts/Makefile.lib" line 94:
# $(modname_flags) #defines KBUILD_MODNAME as the name of the module it will
# end up in (or would, if it gets compiled in)
# Note: Files that end up in two or more modules are compiled without the
# KBUILD_MODNAME definition. The reason is that any made-up name would
# differ in different configs.
For this case, 'radio-si470x-i2c.o' and 'radio-si470x-common.o' are in
one line, so cause compiling issue. And 'uaccess.h' is a common shared
header (not specially for drivers), so use pr_devel() instead of is OK.
The related error with allmodconfig:
CC [M] drivers/media/radio/si470x/radio-si470x-i2c.o
CC [M] drivers/media/radio/si470x/radio-si470x-common.o
In file included from include/linux/printk.h:257:0,
from include/linux/kernel.h:13,
from drivers/media/radio/si470x/radio-si470x.h:29,
from drivers/media/radio/si470x/radio-si470x-common.c:115:
./arch/microblaze/include/asm/uaccess.h: In function 'access_ok':
include/linux/dynamic_debug.h:66:14: error: 'KBUILD_MODNAME' undeclared (first use in this function)
.modname = KBUILD_MODNAME, \
^
include/linux/dynamic_debug.h:76:2: note: in expansion of macro 'DEFINE_DYNAMIC_DEBUG_METADATA'
DEFINE_DYNAMIC_DEBUG_METADATA(descriptor, fmt); \
^
include/linux/printk.h:263:2: note: in expansion of macro 'dynamic_pr_debug'
dynamic_pr_debug(fmt, ##__VA_ARGS__)
^
./arch/microblaze/include/asm/uaccess.h:101:3: note: in expansion of macro 'pr_debug'
pr_debug("ACCESS fail: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
"entry.h" needs 'asmlinkage', and "asm/linkage.h" does not provide it.
So need include "linux/linkage.h" to use generic one instead of.
The related error (with allmodconfig under microblaze):
CC [M] drivers/net/ethernet/emulex/benet/be_main.o
In file included from ./arch/microblaze/include/asm/processor.h:17:0,
from include/linux/prefetch.h:14,
from drivers/net/ethernet/emulex/benet/be_main.c:18:
./arch/microblaze/include/asm/entry.h:33:19: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
extern asmlinkage void do_notify_resume(struct pt_regs *regs, int in_syscall);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pull ext4 bugfix from Ted Ts'o.
[ Hmm. It's possible we should make kfree() aware of error pointers,
and use IS_ERR_OR_NULL rather than a NULL check. But in the meantime
this is obviously the right fix. - Linus ]
* 'for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid trying to kfree an ERR_PTR pointer
Pull nfsd bugfixes from Bruce Fields:
"A couple minor nfsd bugfixes"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
lockd: fix rpcbind crash on lockd startup failure
nfsd4: fix rd_dircount enforcement
Commit 3b29970909 "nfsd4: enforce rd_dircount" totally misunderstood
rd_dircount; it refers to total non-attribute bytes returned, not number
of directory entries returned.
Bring the code into agreement with RFC 3530 section 14.2.24.
Cc: stable@vger.kernel.org
Fixes: 3b29970909 "nfsd4: enforce rd_dircount"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Pull s390 fixes from Martin Schwidefsky:
"A bug fix for the vdso code, the loadparm for booting from SCSI is
added and the access permissions for the dasd module parameters are
corrected"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vdso: remove NULL pointer check from clock_gettime
s390/ipl: Add missing SCSI loadparm attributes to /sys/firmware
s390/dasd: Make module parameter visible in sysfs
Pull cgroup fixes from Tejun Heo:
"This pull request includes Alban's patch to disallow '\n' in cgroup
names.
Two other patches from Li to fix a possible oops when cgroup
destruction races against other file operations and one from Vivek to
fix a unified hierarchy devel behavior"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: check cgroup liveliness before unbreaking kernfs
cgroup: delay the clearing of cgrp->kn->priv
cgroup: Display legacy cgroup files on default hierarchy
cgroup: reject cgroup names with '\n'
Pull percpu fixes from Tejun Heo:
"One patch to fix a failure path in the alloc path. The bug is
dangerous but probably not too likely to actually trigger in the wild
given that there hasn't been any report yet.
The other two are low impact fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: free percpu allocation info for uniprocessor system
percpu: perform tlb flush after pcpu_map_pages() failure
percpu: fix pcpu_alloc_pages() failure path
Pull libata fixes from Tejun Heo:
"Two patches are to add PCI IDs for ICH9 and all others are device
specific fixes. Nothing too interesting"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
ahci: add pcid for Marvel 0x9182 controller
ata: Disabling the async PM for JMicron chip 363/361
ata_piix: Add Device IDs for Intel 9 Series PCH
ahci: Add Device IDs for Intel 9 Series PCH
ata: ahci_tegra: Read calibration fuse
Pull networking fixes from David Miller:
1) Fix skb leak in mac802154, from Martin Townsend
2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
Ayuso
3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel
4) Fix RX checksum configuration in stmmac driver, from Giuseppe
CAVALLARO
5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
i40e, i40evf, mvneta, and qlge, from Vlad Yasevich
6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO
7) Try high order allocations more sanely for SKBs, specifically if a
high order allocation fails, fall back directly to zero order pages
rather than iterating down one order at a time. From Eric Dumazet
8) Fix a memory leak in openvswitch, from Li RongQing
9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky
10) RTNL locking was busted in setsockopt for anycast and multicast, fix
from Sabrina Dubroca
11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel
12) DocBook typo fixes, from Masanari Iida
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
ipv6: restore the behavior of ipv6_sock_ac_drop()
amd-xgbe: Enable interrupts for all management counters
amd-xgbe: Treat certain counter registers as 64 bit
greth: moved TX ring cleaning to NAPI rx poll func
cnic : Cleanup CONFIG_IPV6 & VLAN check
net: treewide: Fix typo found in DocBook/networking.xml
bnx2x: Fix link problems for 1G SFP RJ45 module
3c59x: avoid panic in boomerang_start_xmit when finding page address:
netfilter: add explicit Kconfig for NETFILTER_XT_NAT
ipv6: use addrconf_get_prefix_route() to remove peer addr
ipv6: fix a refcnt leak with peer addr
net-timestamp: only report sw timestamp if reporting bit is set
drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
l2tp: fix race while getting PMTU on PPP pseudo-wire
ipv6: fix rtnl locking in setsockopt for anycast and multicast
VMXNET3: Check for map error in vmxnet3_set_mc
openvswitch: distinguish between the dropped and consumed skb
amd-xgbe: Fix initialization of the wrong spin lock
openvswitch: fix a memory leak
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
...
John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the interface is already gone after joining
the list of anycast on this interface as we don't hold a refcount
for the device, in this case we are safe to ignore the error.
What's more important, for API compatibility we should not
change this behavior for applications even if it were correct.
Fixes: commit a9ed4a2986 ("ipv6: fix rtnl locking in setsockopt for anycast and multicast")
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
new link for - How to piss off a Linux kernel subsystem maintainer
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NFS/RDMA Kconfig symbol was split into separate options for client
and server in commit 2e8c12e1b7 ("xprtrdma: add separate Kconfig
options for NFSoRDMA client and server support").
Update the documentation to reflect this split.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hpfall.c was renamed to freefall.c in 3.16, but this file still refer to
hpfall.c instead of freefall.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The example code provided with the i2c device interface documentation
won't compile since it uses the reserved word "register" to name a
variable.
The compiler fails with this error message:
error: expected identifier or '(' before '=' token
__u8 register = 0x20; /* Device register to access */
^
Rename the variable "register" to simply "reg" in the example code.
Another couple of typos has been fixed as well.
[Change "! =" to "!=".]
Signed-off-by: Jose Alarcon Roldan <jose.alarcon.roldan@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Despite the fact that these functions have been around for years, they
are little used (only 15 uses in 13 files at the preseht time) even
though many other files use work-arounds to achieve the same result.
By documenting them, hopefully they will become more widely used.
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix for recently broken test_suspend= command line argument
(Rafael J Wysocki).
- Fixes for regressions related to the ACPI video driver caused
by switching the default to native backlight handling in 3.16
from Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns
stale values sometimes due to the fact that they are cached
instead of executing the appropriate method (_SUN) every time
(broken in 3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock
in the ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver
from Lan Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM
domains code from Gabriele Mazzotta and Geert Uytterhoeven.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=EzJF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI sysfs, ACPI video, suspend test),
ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
output, a fix and a new CPU ID for the RAPL driver, new blacklist
entry for the ACPI EC driver and a couple of trivial cleanups
(intel_pstate and generic PM domains).
Specifics:
- Fix for recently broken test_suspend= command line argument (Rafael
Wysocki).
- Fixes for regressions related to the ACPI video driver caused by
switching the default to native backlight handling in 3.16 from
Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns stale
values sometimes due to the fact that they are cached instead of
executing the appropriate method (_SUN) every time (broken in
3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM domains
code from Gabriele Mazzotta and Geert Uytterhoeven"
* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
cpufreq: intel_pstate: Remove unneeded variable
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
PM / domains: Make generic_pm_domain.name const
PM / sleep: Fix test_suspend= command line option
ACPI / EC: Add msi quirk for Clevo W350etq
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
Pull filesystem fixes from Al Viro:
"Several bugfixes (all of them -stable fodder).
Alexey's one deals with double mutex_lock() in UFS (apparently, nobody
has tried to test "ufs: sb mutex merge + mutex_destroy" on something
like file creation/removal on ufs). Mine deal with two kinds of
umount bugs, in umount propagation and in handling of automounted
submounts, both resulting in bogus transient EBUSY from umount"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix deadlocks introduced by sb mutex merge
fix EBUSY on umount() from MNT_SHRINKABLE
get rid of propagate_umount() mistakenly treating slaves as busy.
Pull RCU fix from Ingo Molnar:
"A boot hang fix for the offloaded callback RCU model (RCU_NOCB_CPU=y
&& (TREE_CPU=y || TREE_PREEMPT_RC)) in certain bootup scenarios"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make nocb leader kthreads process pending callbacks after spawning
Pull timer fixes from Thomas Gleixner:
"Three fixlets from the timer departement:
- Update the timekeeper before updating vsyscall and pvclock. This
fixes the kvm-clock regression reported by Chris and Paolo.
- Use the proper irq work interface from NMI. This fixes the
regression reported by Catalin and Dave.
- Clarify the compat_nanosleep error handling mechanism to avoid
future confusion"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Update timekeeper before updating vsyscall and pvclock
compat: nanosleep: Clarify error handling
nohz: Restore NMI safe local irq work for local nohz kick
Commit 0244756edc ("ufs: sb mutex merge + mutex_destroy") introduces
deadlocks in ufs_new_inode() and ufs_free_inode().
Most callers of that functions acqure the mutex by themselves and
ufs_{new,free}_inode() do that via lock_ufs(),
i.e we have an unavoidable double lock.
The patch proposes to resolve the issue by making sure that
ufs_{new,free}_inode() are not called with the mutex held.
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=vBFm
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
Fix:
- a direct IO read/buffered read data corruption
- the associated fallout from the DIO data corruption fix
- collapse range bugs that are potential data corruption issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tRQo
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"The fixes all address recently discovered data corruption issues.
The original Direct IO issue was discovered by Chris Mason @ Facebook
on a production workload which mixed buffered reads with direct reads
and writes IO to the same file. The fix for that exposed other issues
with page invalidation (exposed by millions of fsx operations) failing
due to dirty buffers beyond EOF.
Finally, the collapse_range code could also cause problems due to
racing writeback changing the extent map while it was being shifted
around. The commits for that problem are simple mitigation fixes that
prevent the problem from occuring. A more robust fix for 3.18 that
addresses the underlying problem is currently being worked on by
Brian.
Summary of fixes:
- a direct IO read/buffered read data corruption
- the associated fallout from the DIO data corruption fix
- collapse range bugs that are potential data corruption issues"
* tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: trim eofblocks before collapse range
xfs: xfs_file_collapse_range is delalloc challenged
xfs: don't log inode unless extent shift makes extent modifications
xfs: use ranged writeback and invalidation for direct IO
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't dirty buffers beyond EOF
