Some of the values in the default register cache did not represent the codecs
state after reset. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define POWER_OFF_ON_STANDBY cause trobles when trying to get some
sound from codec because code for bias setup was not compiled
(define wasn't defined). This define was removed in commit:
cc3202f5 but again introduced by commit: f0fba2ad1 which then
completely break codec functionality so remove it again.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Those are leftovers from a pre-multicomponent era.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are currently two controls which allow selecting the capture source, one
as a normal control, the other as part of a DAPM_MUX widget.
Remove the normal control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop unused field from the coeff struct, precalculate the srate register at
compile-time and cleanup up the naming.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'Mic Boost2' control's shift was off by one and thus was not working.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Annotate the i2c probe and remove functions with __devinit and __devexit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we specifically want to write a block of data to the hw bypassing the
cache, then allow this to happen inside snd_soc_hw_bulk_write_raw().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows to create DAPM routes depending on those widgets in the
codecs probe function. This is helpful when supporting similar codecs
with minor differences in the DAPM routing with the same driver.
Something similar has already been done for cards in commit
a841ebb9 (ASoC: Create card DAPM widgets early so they can be used in
callbacks).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Actually the current code is perfectly sensible given the hardware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The move over to exposing snd_soc_register_card() let the initialisation
of the driver data we use to find the card in PM operations go AWOL. Fix
this by setting the driver data when we register the card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Control sharing is enabled when two widgets include pointers to the
same kcontrol_new in their definition. Specifically:
static const struct snd_kcontrol_new adcinput_mux =
SOC_DAPM_ENUM("ADC Input", adcinput_enum);
static const struct snd_soc_dapm_widget wm8903_dapm_widgets[] = {
SND_SOC_DAPM_MUX("Left ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
SND_SOC_DAPM_MUX("Right ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
};
This is useful when a single register bit or field affects multiple
muxes at once. The common case is to have separate control bits or
fields for each mux (channel). An alternative way of looking at this
is that the mux is a stereo (or even n-channel) mux, rather than
independant mono muxes.
Without this change, a separate kcontrol will be created for each
DAPM_MUX. This has the following disadvantages:
* Confuses the user/programmer with redundant controls that don't
map to separate hardware.
* When one of the controls is changed, ASoC fails to update the DAPM
logic for paths solely affected by the other controls impacted by
the same register bits. This causes some paths not to be correctly
powered up or down. Prior to this change, to work around this, the
user or programmer had to manually toggle all duplicate controls away
from the intended setting, and then back to it.
Control sharing implies that the control is named based on the
kcontrol_new itself, not any of the widgets that are affected by it.
Control sharing is implemented by: When creating kcontrols, if a
kcontrol does not yet exist for a particular kcontrol_new, then a new
kcontrol is created with a list of widgets containing just a single
entry. This is the normal case. However, if a kcontrol does already
exists for the given kcontrol_new, the current widget is simply added
to that kcontrol's list of affected widgets.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future change will allow multiple widgets to be affected by the same
control. For example, a single register bit that controls separate muxes
in both the L and R audio paths.
This change updates the code that handles relevant controls to be able
to iterate over a list of affected widgets. Note that only the put
functions need significant modification to implement the iteration; the
get functions do not need to iterate, nor unify the results, since all
affected widgets reference the same kcontrol.
When creating the list of widgets, always create a 1-sized list, since
the control sharing is not implemented in this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Future changes will need reference to the kcontrol created for a given
kcontrol_new. Store the created kcontrol values now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future change will modify struct snd_soc_dapm_widget to store the
actual kcontrol pointers for each kcontrol_new in a field named
kcontrols. Rename the existing kcontrols field to enable this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The i2s shutdown callback has the check whether it should be disabled reversed.
Currently it is disabled if another stream is still active, but kept enabled if
the last stream is closed. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the DAPM debugfs entries before freeing the context's widgets, otherwise a
use after free situation might occur.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently debugfs entries for a DAPM widgets are only added in
snd_soc_dapm_debugfs_init. If a widget is added later (for example in the
dai_link's probe callback) it will not show up in debugfs.
This patch moves the creation of the widget debugfs entry to
snd_soc_dapm_new_widgets where it will be added after the widget has been
properly instantiated.
As a side-effect this will also reduce the number of times the DAPM widget list
is iterated during a card's instantiation.
Since it is possible that snd_soc_dapm_new_widgets is invoked form the codecs or
cards probe callbacks, the creation of the debugfs dapm directory has to be
moved before these are called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the creation of the DAPM debugfs directory to snd_soc_dapm_debugfs_init
instead of having the same duplicated code in both codec and card DAPM setup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Free the card's DAPM context when the card is removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enum texts are supposed to be const char * const []. Without the
second const, it gets compile warnings like
sound/soc/codecs/max98095.c:607:2: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Immediately after sending the last fix I realised that the CODEC DAI names
also don't correspond to the WM8994 driver. Update the DAI names to match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This was typoed at some point in the multi-component merge, though the
driver was added along with that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch adds a helper function for searching DAPM widgets by name.
This allows to streamline functions which operate on widgets by name.
It also allows to get rid of copy'n'pasted code which was added to fallback to
widgets from other contexts if the widget was not found in the current context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we can now support multiple platforms allow machines to not specify
a platform in a DAI link. Since the rest of the code requires that we have
a struct device for all objects we do this by substituting in a dummy
device that we register automatically.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
When bringing up audio low power modes boards may configure SYSCLK before
they actually start the FLL as we do much of the clocking setup prior to
the power up sequence.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
DMIC support is automatically disabled when none of the GPIOs are set up
to bring out the DMICCLK and DMICDAT pins at startup.
Note that there's no support for controlling DMIC routing except the power
control so the board DAPM configuration will need to manage DMIC enable and
disable if analogue mics (eg, a headset) also exist.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We can safely divide these down to within the supported SYSCLK range.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The current davinci_mcasp_set_dai_fmt() sets bits ACLKX and ACLKR in the PDIR
register for the codec clock-master/frame-slave mode; however, this results in
the ACLKX and ACLKR pins being outputs according to SPRUFM1 [1] which
conflicts with "codec is clock master."
Similarly to the previous patch in this series, "fix _CBM_CFS hw_params" --
For codec clock-master/frame-slave mode (_CMB_CFS), clear bits ACLKX and ACLKR
in the PDIR register to set the pins as inputs and hence allow externally
sourced bit-clocks.
[1] http://www.ti.com/litv/pdf/sprufm1
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: James Nuss <jamesnuss@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The current davinci_mcasp_set_dai_fmt() sets bits ACLKXE and ACLKRE (CLKXM
and CLKRM as they are reffered to in SPRUFM1 [1]) for codec clock-slave/
frame-slave mode (_CBS_CFS) which selects internally generated bit-clock and
frame-sync signals; however, it does the same thing again for codec
clock-master/frame-slave mode (_CBM_CFS) in the very next case statement which
is incorrectly selecting internally generated bit-clocks in this mode.
For codec clock-master/frame-slave mode (_CBM_CFS), clear bits ACLKXE and
ACLKRE to select externally-generated bit-clocks.
[1] http://www.ti.com/litv/pdf/sprufm1
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: James Nuss <jamesnuss@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
