Fix pat_x_mtrr_type() to use UC_MINUS when the mtrr type return UC. This
is to be consistent with ioremap() and ioremap_nocache() which uses
UC_MINUS.
Consolidate the code such that reserve_memtype() also uses
pat_x_mtrr_type() when the caller doesn't specify any special attribute
(non WB attribute).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212708.939936000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As per SDM, there should not be any aliasing of a WC with any cacheable
type across CPUs. That is if one CPU is changing the identity map
memtype to _WC, no other CPU at the time of this change should not have a
TLB for this page that carries a WB attribute. SDM suggests to make the
page not present. But for that we will have to handle any page faults
that can potentially happen due to these pages being not present.
Other way to deal with this without having any WB mapping is to change
the page first to UC and then to WC. This ensures that we meet the SDM
requirement of no cacheable alais to WC page. This also has same or
lower overhead than marking the page not present and making it present
later.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090409212708.797481000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Handle faults and do proper cleanups in set_memory_*() functions. In
some cases, these functions were not doing proper free on failure paths.
With the changes to tracking memtype of RAM pages in struct page instead
of pat list, we do not need the changes in commits c5e147. This patch
reverts that change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090409212708.653222000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To be free of aliasing due to races, set_memory_* interfaces should
follow ordering of reserving, changing memtype to UC/WC, changing
memtype back to WB followed by free.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090409212708.512280000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change the identity mapping with the requested attribute first, before
we setup the virtual memory mapping with the new requested attribute.
This makes sure that there is no window when identity map'ed attribute
may disagree with ioremap range on the attribute type.
This also avoids doing cpa on the ioremap'ed address twice (first in
ioremap_page_range and then in ioremap_change_attr using vaddr), and
should improve ioremap performance a bit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20090409212708.373330000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While better than get_user_pages(), the usage of gupf(),
especially the return values and the fact that it can
potentially only partially pin the range, warranted some
documentation.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Cc: npiggin@suse.de
Cc: akpm@linux-foundation.org
LKML-Reference: <1239320729-3262-1-git-send-email-andy.grover@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To simplify level irq migration in the presence of interrupt-remapping,
Suresh used a virtual vector (io-apic pin number) to eliminate io-apic
RTE modification. Level triggered interrupt will appear as an edge to
the local apic cpu but still as level to the IO-APIC. So in addition to
do the local apic EOI, it still needs to do IO-APIC directed EOI to clear
the remote IRR bit in the IO-APIC RTE. Pls refer to Suresh's patch for
more details (commit 0280f7c416).
Now interrupt remapping is decoupled from x2apic, it also needs to do the
directed EOI for apic. Otherwise, apic interrupts won't work correctly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: Weidong Han <weidong.han@intel.com>
Cc: suresh.b.siddha@intel.com
Cc: dwmw2@infradead.org
Cc: allen.m.kay@intel.com
LKML-Reference: <1239355037-22856-1-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: speed up
The return to handler portion of the function graph tracer should only
need to save the return values. The caller already saved off the
registers that the callee can modify. The returning function already
saved the registers it modified. When we call our own trace function
it too will save the registers that the callee must restore.
There's no reason to save off anything more that the registers used
to return the values.
Note, I did a complete kernel build with this modification and the
function graph tracer running on x86_64.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use phys_addr_t for receiving a physical address argument instead of
unsigned long. This allows fixmap to handle pages higher than 4GB on
x86-32.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug remove execute permission
x86: smarten /proc/interrupts output for new counters
x86: DMI match for the Dell DXP061 as it needs BIOS reboot
x86: make 64 bit to use default_inquire_remote_apic
x86, setup: un-resequence mode setting for VGA 80x34 and 80x60 modes
x86, intel-iommu: fix X2APIC && !ACPI build failure
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: consolidate documents
blktrace: pass the right pointer to kfree()
tracing/syscalls: use a dedicated file header
tracing: append a comma to INIT_FTRACE_GRAPH
It seems by mistake these files got execute permissions so removing it.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1239211186.9037.2.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build warnings and possibe compat misbehavior on IA64
Building a kernel on ia64 might trigger these ugly build warnings:
CC arch/ia64/ia32/sys_ia32.o
In file included from arch/ia64/ia32/sys_ia32.c:55:
arch/ia64/ia32/ia32priv.h:290:1: warning: "elf_check_arch" redefined
In file included from include/linux/elf.h:7,
from include/linux/module.h:14,
from include/linux/ftrace.h:8,
from include/linux/syscalls.h:68,
from arch/ia64/ia32/sys_ia32.c:18:
arch/ia64/include/asm/elf.h:19:1: warning: this is the location of the previous definition
[...]
sys_ia32.c includes linux/syscalls.h which in turn includes linux/ftrace.h
to import the syscalls tracing prototypes.
But including ftrace.h can pull too much things for a low level file,
especially on ia64 where the ia32 private headers conflict with higher
level headers.
Now we isolate the syscall tracing headers in their own lightweight file.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jason Baron <jbaron@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jiaying Zhang <jiayingz@google.com>
Cc: Michael Rubin <mrubin@google.com>
Cc: Martin Bligh <mbligh@google.com>
Cc: Michael Davidson <md@google.com>
LKML-Reference: <20090408184058.GB6017@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
FIX_TEXT_POKE[01] are used to map kernel addresses, so they're mapping
pfns, not mfns.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Some 64-bit machines don't support the NX flag in ptes.
Check for NX before constructing the kernel pagetables.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: fixes crashing bug
There's no particular problem with getting an empty cpu mask,
so just shortcut-return if we get one.
Avoids crash reported by Christophe Saout <christophe@saout.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
1. make sure early-allocated ptes are pinned, so they can be later
unpinned
2. don't pin pmd+pud, just make them RO
3. scatter some __inits around
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
PGE may not be available when running paravirtualized, so test the cpuid
bit before using it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Xen leaves XSAVE set in cpuid, but doesn't allow cr4.OSXSAVE
to be set. This confuses the kernel and it ends up crashing on
an xsetbv instruction.
At boot time, try to set cr4.OSXSAVE, and mask XSAVE out of
cpuid it we can't. This will produce a spurious error from Xen,
but allows us to support XSAVE if/when Xen does.
This also factors out the cpuid mask decisions to boot time.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Fix this sparse warnings:
arch/x86/xen/smp.c:316:52: warning: Using plain integer as NULL pointer
arch/x86/xen/smp.c:421:60: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Remove use of multicall machinery which is unused (gdt loading
is never performance critical). This removes the implicit use
of percpu variables, which simplifies understanding how
the percpu code's use of load_gdt interacts with this code.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Build the p2m_mfn_list_list early with the rest of the p2m table, but
register it later when the real shared_info structure is in place.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When doing very early p2m setting, we need to separate setting
from allocation, so split things up accordingly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
xen_mc_flush() requires preemption to be disabled for its own sanity,
so disable it while we're flushing.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Now /proc/interrupts of tip tree has new counters:
PLT: Platform interrupts
Format change of output, as like that by commit:
commit 7a81d9a7da
x86: smarten /proc/interrupts output
should be applied to these new counters too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49C98DEA.8060208@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: restore old behavior
for flat and phys_flat
Signed-off-by: Yinhai Lu <yinghai@kernel.org.
LKML-Reference: <49DCBBF1.8080903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix
Add Kconfig dependency on NUMA for enabling UV. Although it might
be possible to configure non-NUMA UV systems, they are unsupported
and not interesting. Much of the infrastructure for UV requires
NUMA support.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090403203942.GA20137@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/sys/firmware/sgi_uv should only be created on uv systems.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20090403222423.GA28546@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for Always Running APIC timer, CPUID_0x6_EAX_Bit2.
This bit means the APIC timer continues to run even when CPU is
in deep C-states.
The advantage is that we can use LAPIC timer on these CPUs
always, and there is no need for "slow to read and program"
external timers (HPET/PIT) and the timer broadcast logic
and related code in C-state entry and exit.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Do not write zeroes to APERF and MPERF by ondemand governor. With this
change, other users can share these MSRs for reads.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change structure name to make the code cleaner and simpler. No
functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
branch tracer: Fix for enabling branch profiling makes sparse unusable
ftrace: Correct a text align for event format output
Update /debug/tracing/README
tracing/ftrace: alloc the started cpumask for the trace file
tracing, x86: remove duplicated #include
ftrace: Add check of sched_stopped for probe_sched_wakeup
function-graph: add proper initialization for init task
tracing/ftrace: fix missing include string.h
tracing: fix incorrect return type of ns2usecs()
tracing: remove CALLER_ADDR2 from wakeup tracer
blktrace: fix pdu_len when tracing packet command requests
blktrace: small cleanup in blk_msg_write()
blktrace: NUL-terminate user space messages
tracing: move scripts/trace/power.pl to scripts/tracing/power.pl
Impact: Fixes these modes on at least one system
The rewrite of the setup code into C resequenced the font setting and
register reprogramming phases of configuring nonstandard VGA modes
which use 480 scan lines in text mode. However, there exists at least
one board (Micro-Star MS-7383 version 2.0) on which this resequencing
causes an unusable display.
Revert to the original sequencing: set up 480-line mode, install the
font, and then adjust the vertical end register appropriately.
This failure was masked by the fact that the 480-line setup was broken
until checkin 5f64135612 (therefore this
is not a -stable candidate bug fix.)
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add debug store support for Core i7.
Core i7 adds a reset value for each performance counter and a new
PEBS record format.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144607.088997000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check the buffer size more precisely to allow buffers for exactly
one element provided the base address is already properly aligned.
Add a debug store selftest.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144606.139137000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ds_reset_pebs() passed the wrong qualifier to a shared function resulting
in a reset of bts, rather than pebs.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144605.206510000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Debug store already uses TIF_DS_AREA_MSR to trigger debug store context
switch handling. No need to use TIF_DEBUGCTLMSR, as well.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144604.256645000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add the ptrace bts context field to task_struct unconditionally.
Initialize the field directly in copy_process().
Remove all the unneeded functionality used to initialize that field.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144603.292754000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a warning in case a debug store context is not removed before
the task it is attached to is freed.
Remove the old warning at thread exit. It is too early.
Declare the debug store context field in thread_struct unconditionally.
Remove ds_copy_thread() and ds_exit_thread() and do the work directly
in process*.c.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144601.254472000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Perform debug store selftests on each cpu.
Cover both the normal and the _noirq variant of the debug store interface.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144559.394583000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The hw-branch-tracer uses debug store functions from an on_each_cpu()
context, which is simply wrong since the functions may sleep.
Add _noirq variants for most functions, which may be called with
interrupts disabled.
Separate per-cpu and per-task tracing and allow per-cpu tracing to be
controlled from any cpu.
Make the hw-branch-tracer use the new debug store interface, synchronize
with hotplug cpu event using get/put_online_cpus(), and remove the
unnecessary spinlock.
Make the ptrace bts and the ds selftest code use the new interface.
Defer the ds selftest.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144555.658136000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Per-task branch tracing installs a debug store context with the traced
task. This immediately results in the branch trace control bits to be
cleared for the next context switch of that task, if not set before.
Either per-cpu or per-task tracing are allowed at the same time.
An active per-cpu tracing would be disabled even if the per-task tracing
request is rejected and the task debug store context removed.
Check the tracing type (per-cpu or per-task) before installing a task
debug store context.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: oleg@redhat.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144552.856000000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to stop branch tracing for a running task, we need to first
clear the branch tracing control bits before we may free the tracing
buffer.
If the traced task is running, the cpu might still trace that task
after the branch trace control bits have cleared.
Wait until the traced task has been scheduled out before proceeding.
A similar problem affects the task debug store context. We first remove
the context, then we need to wait until the task has been scheduled
out before we can free the context memory.
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144551.919636000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a ptraced task is unlinked, we need to stop branch tracing for
that task.
Since the unlink is called with interrupts disabled, and we need
interrupts enabled to stop branch tracing, we defer the work.
Collect all branch tracing related stuff in a branch tracing context.
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144550.712401000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the bts tracer is removed while the traced task is running,
the write to clear the bts tracer pointer races with context switch code.
Read the tracer once during a context switch.
When a new tracer is installed, the bts tracer is set in the ds context
before the tracer is initialized in order to claim the context for that
tracer.
This may result in write accesses using an uninitialized trace configuration
when scheduling timestamps have been requested.
Store active tracing flags separately and only set active flags after
the tracing configuration has been initialized.
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Cc: roland@redhat.com
Cc: eranian@googlemail.com
Cc: juan.villacis@intel.com
Cc: ak@linux.jf.intel.com
LKML-Reference: <20090403144548.881338000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This build failure:
| drivers/pci/dmar.c:47: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘dmar_tbl_size’
| drivers/pci/dmar.c:62: warning: ‘struct acpi_dmar_device_scope’ declared inside parameter list
| drivers/pci/dmar.c:62: warning: its scope is only this definition or declaration, which is probably not what you want
Triggers due to this commit:
d0b03bd: x2apic/intr-remap: decouple interrupt remapping from x2apic
Which exposed a pre-existing but dormant fragility of the 'select X86_X2APIC'
it moved around and turned that fragility into a build failure.
Replace it with a proper 'depends on' construct.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
LKML-Reference: <1239084280.22733.404.camel@macbook.infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove dupilicated #include in arch/x86/kernel/cpu/cpufreq/longhaul.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
interrupt remapping must be enabled before enabling x2apic, but
interrupt remapping doesn't depend on x2apic, it can be used
separately. Enable interrupt remapping in init_dmars even x2apic
is not supported.
[dwmw2: Update Kconfig accordingly, fix build with INTR_REMAP && !X2APIC]
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All logical processors with APIC ID values of 255 and greater will have their
APIC reported through Processor X2APIC structure (type-9 entry type) and all
logical processors with APIC ID less than 255 will have their APIC reported
through legacy Processor Local APIC (type-0 entry type) only. This is the
same case even for NMI structure reporting.
The Processor X2APIC Affinity structure provides the association between the
X2APIC ID of a logical processor and the proximity domain to which the logical
processor belongs.
For OSPM, Procssor IDs outside the 0-254 range are to be declared as Device()
objects in the ACPI namespace.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
pci mmap code was doing memtype reserve for a while now. Recently we
added memtype tracking in remap_pfn_range, and pci code indirectly calls
remap_pfn_range. So, we don't need seperate tracking in pci code
anymore. Which means a patch that removes ~50 lines of code :-).
Also, recently we found out that the pci tracking is not working as we expect
it to work in some cases. Specifically, userlevel X mmap of pci, with some
recent version of X, is having a problem with vm_page_prot getting reset.
The pci tracking uses vm_page_prot to pass on the protection type from parent
to child during fork.
a) Parent does a pci mmap
b) We look at PAT and get either UC_MINUS or WC mapping for parent
c) Store that mapping type in vma vm_page_prot for future use
d) This thread does a fork
e) Fork results in mmap_ops ->open for the child process
f) We get the vm_page_prot from vma and reserve that type for the child process
But, between c) and e) above, the vma vm_page_prot is getting reset to zero.
This results in PAT reserve failing at the time of fork as in here.
http://marc.info/?l=linux-kernel&m=123858163103240&w=2
This cleanup makes the above problem go away as we do not depend on
vm_page_prot in our PAT code anymore.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables suspend/resume for interrupt remapping. During suspend,
interrupt remapping is disabled. When resume, interrupt remapping is enabled
again.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix initialization of UV blade information for systems that have
nodes with memory but no cpus.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090330140111.GA18461@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The __restore_processor_state() fn restores %gs on resume from S3. As
such, it cannot be protected by the stack-protector guard since %gs will
not be correct on function entry.
There are only a few other fns in this file and it should not negatively
impact kernel security that they will also have the stack-protector
guard removed (and so it's not worth moving them to another file).
Without this change, S3 resume on a kernel built with
CONFIG_CC_STACKPROTECTOR_ALL=y will fail.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
LKML-Reference: <49D13385.5060900@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Fix address wrap on 32-bit kernel.
intel-iommu: Enable DMAR on 32-bit kernel.
intel-iommu: fix PCI device detach from virtual machine
intel-iommu: VT-d page table to support snooping control bit
iommu: Add domain_has_cap iommu_ops
intel-iommu: Snooping control support
Fixed trivial conflicts in arch/x86/Kconfig and drivers/pci/intel-iommu.c
Use the copy of UV system table in kernel memory, not the one in
bios after unmapping.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20090330225240.GA22776@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 7ca43e7564 ("mm: use debug_kmap_atomic")
introduced some debug_kmap_atomic() in wrong places.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i386 allnoconfig:
arch/x86/mm/iomap_32.c: In function 'is_io_mapping_possible':
arch/x86/mm/iomap_32.c:27: warning: comparison is always false due to limited range of data type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch replaces a 'nop' uv_enable_timeouts() in the
UV TLB shootdown code. (somehow, long ago that function got
eviscerated)
If any cpu in the destination node does not get interrupted by the
message and post completion in a reasonable time the hardware
should respond to the sender with an error. This function
enables such timeouts.
Tested on the UV hardware simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1LpjXU-00007e-Qh@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes BAU initialization for systems containing
nodes with no memory and for systems with non-consecutive
node numbers.
Fixes and clarifies situations where pnode should be used instead
of node id.
Tested on the UV hardware simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1LpjX3-00007N-12@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: code size reduction (possibly critical)
The x86 boot and decompression code has no use of the branch profiling
constructs, so disable them. This would bloat the setup code by as
much as 14K, eating up a fairly large chunk of the 32K area we are
guaranteed to have.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: unification of pci-dma macros and pci_32.h removal
This patch unifies the definition of the pci_unmap_addr*, pci_unmap_len*
and DECLARE_PCI_UNMAP* macros. This makes sense because the pci_unmap
functions are no longer no-ops anymore when the kernel runs with
CONFIG_DMA_API_DEBUG. Without an iommu or DMA_API_DEBUG it is a no-op on 32 bit
because the dma mapping path returns a physical address and therefore the
dma-api implementation has no internal state which needs to be destroyed with
an unmap call.
This unification also simplifies the port of x86_64 iommu drivers to 32 bit x86
and let us get rid of pci_32.h.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds preadv and pwritev system calls. These syscalls are a
pretty straightforward combination of pread and readv (same for write).
They are quite useful for doing vectored I/O in threaded applications.
Using lseek+readv instead opens race windows you'll have to plug with
locking.
Other systems have such system calls too, for example NetBSD, check
here: http://www.daemon-systems.org/man/preadv.2.html
The application-visible interface provided by glibc should look like
this to be compatible to the existing implementations in the *BSD family:
ssize_t preadv(int d, const struct iovec *iov, int iovcnt, off_t offset);
ssize_t pwritev(int d, const struct iovec *iov, int iovcnt, off_t offset);
This prototype has one problem though: On 32bit archs is the (64bit)
offset argument unaligned, which the syscall ABI of several archs doesn't
allow to do. At least s390 needs a wrapper in glibc to handle this. As
we'll need a wrappers in glibc anyway I've decided to push problem to
glibc entriely and use a syscall prototype which works without
arch-specific wrappers inside the kernel: The offset argument is
explicitly splitted into two 32bit values.
The patch sports the actual system call implementation and the windup in
the x86 system call tables. Other archs follow as separate patches.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add macros for using the UV hub to send interrupts. Change the IPI code
to use these macros. These macros will also be used in additional patches
that will follow.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate compile errors on 32-bit X86 caused by UV.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Container-init must behave like global-init to processes within the
container and hence it must be immune to unhandled fatal signals from
within the container (i.e SIG_DFL signals that terminate the process).
But the same container-init must behave like a normal process to processes
in ancestor namespaces and so if it receives the same fatal signal from a
process in ancestor namespace, the signal must be processed.
Implementing these semantics requires that send_signal() determine pid
namespace of the sender but since signals can originate from workqueues/
interrupt-handlers, determining pid namespace of sender may not always be
possible or safe.
This patchset implements the design/simplified semantics suggested by
Oleg Nesterov. The simplified semantics for container-init are:
- container-init must never be terminated by a signal from a
descendant process.
- container-init must never be immune to SIGKILL from an ancestor
namespace (so a process in parent namespace must always be able
to terminate a descendant container).
- container-init may be immune to unhandled fatal signals (like
SIGUSR1) even if they are from ancestor namespace. SIGKILL/SIGSTOP
are the only reliable signals to a container-init from ancestor
namespace.
This patch:
Based on an earlier patch submitted by Oleg Nesterov and comments from
Roland McGrath (http://lkml.org/lkml/2008/11/19/258).
The handler parameter is currently unused in the tracehook functions.
Besides, the tracehook functions are called with siglock held, so the
functions can check the handler if they later need to.
Removing the parameter simiplifies changes to sig_ignored() in a follow-on
patch.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build failure with generic debug pagealloc:
mm/debug-pagealloc.c: In function 'set_page_poison':
mm/debug-pagealloc.c:8: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: In function 'clear_page_poison':
mm/debug-pagealloc.c:13: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: In function 'page_poison':
mm/debug-pagealloc.c:18: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: At top level:
mm/debug-pagealloc.c:120: error: redefinition of 'kernel_map_pages'
include/linux/mm.h:1278: error: previous definition of 'kernel_map_pages' was here
mm/debug-pagealloc.c: In function 'kernel_map_pages':
mm/debug-pagealloc.c:122: error: 'debug_pagealloc_enabled' undeclared (first use in this function)
by fixing
- debug_flags should be in struct page
- define DEBUG_PAGEALLOC config option for all architectures
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: clean up
those code pcpu_need_numa(), should be removed.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
LKML-Reference: <49D31770.9090502@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
setup_percpu_remap() is for NUMA machines yet it bailed out with
-EINVAL if pcpu_need_numa(). Fix the inverted condition.
This problem was reported by David Miller and verified by Yinhai Lu.
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <49D30469.8020006@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: guard against pre-ACPI 3 e820 code not updating %ecx
Impact: BIOS bug safety
For pre-ACPI 3 BIOSes, pre-initialize the end of the e820 buffer just
in case the BIOS returns an unchanged %ecx but without actually
touching the ACPI 3 extended flags field.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86/setup' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: ACPI 3, BIOS workaround for E820-probing code
x86, setup: preemptively save/restore edi and ebp around INT 15 E820
x86, setup: mark %esi as clobbered in E820 BIOS call
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
Make the following header file changes:
- remove arch ifdefs and asm/suspend.h from linux/suspend.h
- add asm/suspend.h to disk.c (for arch_prepare_suspend())
- add linux/io.h to swsusp.c (for ioremap())
- x86 32/64 bit compile fixes
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use debug_kmap_atomic in kmap_atomic, kmap_atomic_pfn, and
iomap_atomic_prot_pfn.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 has debug_kmap_atomic_prot() which is error checking function for
kmap_atomic. It is usefull for the other architectures, although it needs
CONFIG_TRACE_IRQFLAGS_SUPPORT.
This patch exposes it to the other architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_DEBUG_PAGEALLOC is now supported by x86, powerpc, sparc64, and
s390. This patch implements it for the rest of the architectures by
filling the pages with poison byte patterns after free_pages() and
verifying the poison patterns before alloc_pages().
This generic one cannot detect invalid page accesses immediately but
invalid read access may cause invalid dereference by poisoned memory and
invalid write access can be detected after a long delay.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix redundant and incorrect check
Oleg Nesterov noticed wrt commit:
14fc9fb: x86: signal: check signal stack overflow properly
>> No need to check SA_ONSTACK if we're already using alternate signal stack.
>
> Yes, but this also mean that we don't need sas_ss_flags() under
> "if (!onsigstack)",
Checking on_sig_stack() in sas_ss_flags() at get_sigframe() is redundant
and not correct on 64 bit. To check sas_ss_size is enough.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: roland@redhat.com
LKML-Reference: <49CBB54C.5080201@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest-and-virtio:
lguest: barrier me harder
lguest: use bool instead of int
lguest: use KVM hypercalls
lguest: wire up pte_update/pte_update_defer
lguest: fix spurious BUG_ON() on invalid guest stack.
virtio: more neatening of virtio_ring macros.
virtio: fix BAD_RING, START_US and END_USE macros
* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
Revert "proc: revert /proc/uptime to ->read_proc hook"
proc 2/2: remove struct proc_dir_entry::owner
proc 1/2: do PDE usecounting even for ->read_proc, ->write_proc
proc: fix sparse warnings in pagemap_read()
proc: move fs/proc/inode-alloc.txt comment into a source file
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PCI PM: Make pci_prepare_to_sleep() disable wake-up if needed
radeonfb: Use __pci_complete_power_transition()
PCI PM: Introduce __pci_[start|complete]_power_transition() (rev. 2)
PCI PM: Restore config spaces of all devices during early resume
PCI PM: Make pci_set_power_state() handle devices with no PM support
PCI PM: Put devices into low power states during late suspend (rev. 2)
PCI PM: Move pci_restore_standard_config to pci-driver.c
PCI PM: Use pci_set_power_state during early resume
PCI PM: Consistently use variable name "error" for pm call return values
kexec: Change kexec jump code ordering
PM: Change hibernation code ordering
PM: Change suspend code ordering
PM: Rework handling of interrupts during suspend-resume
PM: Introduce functions for suspending and resuming device interrupts
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
dma-debug: make memory range checks more consistent
dma-debug: warn of unmapping an invalid dma address
dma-debug: fix dma_debug_add_bus() definition for !CONFIG_DMA_API_DEBUG
dma-debug/x86: register pci bus for dma-debug leak detection
dma-debug: add a check dma memory leaks
dma-debug: add checks for kernel text and rodata
dma-debug: print stacktrace of mapping path on unmap error
dma-debug: Documentation update
dma-debug: x86 architecture bindings
dma-debug: add function to dump dma mappings
dma-debug: add checks for sync_single_sg_*
dma-debug: add checks for sync_single_range_*
dma-debug: add checks for sync_single_*
dma-debug: add checking for [alloc|free]_coherent
dma-debug: add add checking for map/unmap_sg
dma-debug: add checking for map/unmap_page/single
dma-debug: add core checking functions
dma-debug: add debugfs interface
dma-debug: add kernel command line parameters
dma-debug: add initialization code
...
Fix trivial conflicts due to whitespace changes in arch/x86/kernel/pci-nommu.c
Use the functions introduced in by the previous patch,
suspend_device_irqs(), resume_device_irqs() and check_wakeup_irqs(),
to rework the handling of interrupts during suspend (hibernation) and
resume. Namely, interrupts will only be disabled on the CPU right
before suspending sysdevs, while device drivers will be prevented
from receiving interrupts, with the help of the new helper function,
before their "late" suspend callbacks run (and analogously during
resume).
In addition, since the device interrups are now disabled before the
CPU has turned all interrupts off and the CPU will ACK the interrupts
setting the IRQ_PENDING bit for them, check in sysdev_suspend() if
any wake-up interrupts are pending and abort suspend if that's the
case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'x86-stage-3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (190 commits)
Revert "cpuacct: reduce one NULL check in fast-path"
Revert "x86: don't compile vsmp_64 for 32bit"
x86: Correct behaviour of irq affinity
x86: early_ioremap_init(), use __fix_to_virt(), because we are sure it's safe
x86: use default_cpu_mask_to_apicid for 64bit
x86: fix set_extra_move_desc calling
x86, PAT, PCI: Change vma prot in pci_mmap to reflect inherited prot
x86/dmi: fix dmi_alloc() section mismatches
x86: e820 fix various signedness issues in setup.c and e820.c
x86: apic/io_apic.c define msi_ir_chip and ir_ioapic_chip all the time
x86: irq.c keep CONFIG_X86_LOCAL_APIC interrupts together
x86: irq.c use same path for show_interrupts
x86: cpu/cpu.h cleanup
x86: Fix a couple of sparse warnings in arch/x86/kernel/apic/io_apic.c
Revert "x86: create a non-zero sized bm_pte only when needed"
x86: pci-nommu.c cleanup
x86: io_delay.c cleanup
x86: rtc.c cleanup
x86: i8253 cleanup
x86: kdebugfs.c cleanup
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (180 commits)
powerpc: clean up ssi.txt, add definition for fsl,ssi-asynchronous
powerpc/85xx: Add support for the "socrates" board (MPC8544).
powerpc: Fix bugs introduced by sysfs changes
powerpc: Sanitize stack pointer in signal handling code
powerpc: Add write barrier before enabling DTL flags
powerpc/83xx: Update ranges in gianfar node to match other dts
powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/85xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/83xx: Add power management support for MPC837x boards
powerpc/mm: Introduce early_init_mmu() on 64-bit
powerpc/mm: Add option for non-atomic PTE updates to ppc64
powerpc/mm: Fix printk type warning in mmu_context_nohash
powerpc/mm: Rename arch/powerpc/kernel/mmap.c to mmap_64.c
powerpc/mm: Merge various PTE bits and accessors definitions
powerpc/mm: Tweak PTE bit combination definitions
powerpc/cell: Fix iommu exception reporting
powerpc/mm: e300c2/c3/c4 TLB errata workaround
powerpc/mm: Used free register to save a few cycles in SW TLB miss handling
powerpc/mm: Remove unused register usage in SW TLB miss handling
...
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Impact: cleanup
This patch allow us to use KVM hypercalls
Signed-off-by: Matias Zabaljauregui <zabaljauregui at gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: intermittent guest segv/crash fix
I've been seeing random guest bad address crashes and segmentation faults:
bisect led to 4f98a2fee8 (vmscan: split LRU lists into anon & file sets),
but that's a red herring.
It turns out that lguest never hooked up the pte_update/pte_update_defer
calls, so our ptes were not always in sync. After the vmscan commit, the
bug became reproducible; now a fsck in a 64MB guest causes reproducible
pagetable corruption.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: jeremy@xensource.com
Cc: virtualization@lists.osdl.org
Cc: stable@kernel.org
Impact: ACPI 3 spec compliance, BIOS bug workaround
The ACPI 3 spec added another field to the E820 buffer -- which is
backwards incompatible, since it contains a validity bit.
Furthermore, there has been at least one report of a BIOS which
assumes that the buffer it is pointed at is the same buffer as for the
previous E820 call. Therefore, read the data into a temporary buffer
and copy the standard part of it if and only if the valid bit is set.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: BIOS bugproofing
Since there are BIOSes known to clobber %ebx and %esi for INT 15 E820,
assume there is something out there clobbering %edi and/or %ebp too,
and don't wait for it to fail.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jordan Hargrave diagnosed a BIOS clobbering %esi in the E820 call.
That particular BIOS has been fixed, but there is a possibility that
this is responsible for other occasional reports of early boot
failure, and it does not hurt to add %esi to the clobbers.
-stable candidate patch.
Cc: Justin Forbes <jmforbes@linuxtx.org>
Signed-off-by: Michael K Johnson <johnsonm@rpath.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes report very high frequency transition latency which are plainly
wrong on CPus that can change frequency using native MSR interface.
One such system is IBM T42 (2327-8ZU) as reported by Owen Taylor and
Rik van Riel.
cpufreq_ondemand driver uses this transition latency to come up with a
reasonable sampling interval to sample CPU usage and with such high
latency value, ondemand sampling interval ends up being very high
(0.5 sec, in this particular case), resulting in performance impact due to
slow response to increasing frequency.
Fix it by capping-off the transition latency to 20uS for native MSR based
frequency transitions.
mjg: We've confirmed that this also helps on the X31
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
> arch/x86/kernel/cpu/cpufreq/longhaul.c: In function 'longhaul_setstate':
> arch/x86/kernel/cpu/cpufreq/longhaul.c:308: error: implicit declaration of function 'acpi_set_register'
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Compile-tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
Due to a different size of ino_t ustat needs a compat handler, but
currently only x86 and mips provide one. Add a generic compat_sys_ustat
and switch all architectures over to it. Instead of doing various
user copy hacks compat_sys_ustat just reimplements sys_ustat as
it's trivial. This was suggested by Arnd Bergmann.
Found by Eric Sandeen when running xfstests/017 on ppc64, which causes
stack smashing warnings on RHEL/Fedora due to the too large amount of
data writen by the syscall.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Impact: scan more peer root buses even acpi is used
Move pci_bios_fixup_peer_bridges out of pci_legacy_init and into
pci_subsys_init. This allows pci_bios_fixup_peer_bridges to be called
even pci_apci_init is driving PCI initialization.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
* 'sched-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
sched: Add comments to find_busiest_group() function
sched: Refactor the power savings balance code
sched: Optimize the !power_savings_balance during fbg()
sched: Create a helper function to calculate imbalance
sched: Create helper to calculate small_imbalance in fbg()
sched: Create a helper function to calculate sched_domain stats for fbg()
sched: Define structure to store the sched_domain statistics for fbg()
sched: Create a helper function to calculate sched_group stats for fbg()
sched: Define structure to store the sched_group statistics for fbg()
sched: Fix indentations in find_busiest_group() using gotos
sched: Simple helper functions for find_busiest_group()
sched: remove unused fields from struct rq
sched: jiffies not printed per CPU
sched: small optimisation of can_migrate_task()
sched: fix typos in documentation
sched: add avg_overlap decay
x86, sched_clock(): mark variables read-mostly
sched: optimize ttwu vs group scheduling
sched: TIF_NEED_RESCHED -> need_reshed() cleanup
sched: don't rebalance if attached on NULL domain
...
