From the Windows INF file, we know the firmware ranges for all RME
cards. For PCIe, a single revision ID per device (RayDAT, MADI, AIO,
AES) is used. Contrary, the older PCI versions use ranges, that is,
one revision ID per firmware version.
Instead of listing all possible revisions individually, match the range.
This commit enables all MADI and AES PCI versions ever shipped.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSP_VERSION_BIT has to be ORed with HDSP_S_LOAD. This fixes the detection
of at least some RME RPM boxes.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_HDSPM_IOCTL_GET_STATUS is supposed to query the current card
status, so we have to return what we receive on the MADI wire (RX), not
what we transmit (TX) to others. The latter is a config item to be
queried via SNDRV_HDSPM_IOCTL_GET_CONFIG.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch complains that if device is INT_MAX then device + 1 can
overflow. It just means we would have an annoying loop while we
check all the devices from -2147483648 to SNDRV_MINOR_HWDEPS.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
It seems that Conexant CX20549 chip handle only a single input-amp even
though the audio-input widget has multiple sources. This has been never
clear, and I implemented in the current way based on the debug information
I got at the early time -- the device reacts individual input-amp values
for different sources. This is true for another Conexant codec, but it's
not applied to CX20549 actually.
This patch changes the auto-parser code to handle a single input-amp
per audio-in widget for CX20549. After applying this, you'll see only a
single "Capture" volume control instead of separate "Mic" or "Line"
captures when the device is set up to use a single ADC.
We haven't tested 20551 and 20561 codecs yet. If these show the similar
behavior like 20549, they need to set spec->single_adc_amp=1, too.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the old Conexant chips (5045, 5047, 5051 and 5066), a single EAPD
may handle both headphone and speaker outputs while it's assigned only
to one of them. Turning off dynamically leads to the unexpected silent
output in such a configuration with the auto-mute function.
Since it's difficult to know how the EAPD is handled in the actual h/w
implementation, better to keep EAPD on while running for such codecs.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC260 has multiple mixer widgets connected to the shared DAC, but the
driver currently doesn't check this possibility and ignores when the DAC
is shared with others. This resulted in the silent output from some
routes because of lack of the amp setup.
This patch adds the workaround for it by checking the route even with the
shared DAC, but also checking the conflict with the existing control for
the very same widget NID.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=726812
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the datasheet:
Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
0: Bit clock is an input (slave mode)
1: Bit clock is an output (master mode)
BIT 6: Word Clock Directional Control
0: Word clock is an input (slave mode)
1: Word clock is an output (master mode)
Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
Digital Audio Interface Format (07h) register:
BIT6: Master/slave mode
0: Slave
1: Master
Current code sets TLV320AIC23_MS_MASTER bit for master mode,
but does not clear it for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
BCLK is controlled by BIT[4:2] of WM8940_CLOCK(06h) register.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The association numbers of surround/CLFE speaker pins aren't correctly
mapped by the auto-parser. This patch fixes the CLFE speaker pin to the
right assoc value (from 3 to 1).
Tested-by: Nika Topolchanskaya <nanodesuu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When 5.1 or more headphone or speaker pins are provided, the parser still
takes as is without fixing the order of channel mapping, which leads in
the unexpected strange channel order by surround outputs.
This patch fixes the issue by applying the same fix-up not only to
line_out_pins[] but also hp_pins[] and speaker_pins[].
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The revision 0x100300 was found for ALC662. It seems to work well
with patch_alc662.
Cc: stable@kernel.org
BugLink: http://bugs.launchpad.net/bugs/877373
Tested-by: Shengyao Xue <Shengyao.xue@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Acked-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
codec->hw_write is broken now, convert codec->hw_write to snd_soc_write.
The hardware has 2 banks of registers sharing a section in I2C register space.
The 1st bank is the primary one and is cached.
The 2nd bank is for loading coefficients only and they do not need cache.
These coefficients registers are therefore direct writes.
Thus we set cache_bypass flag to deal with this before calling snd_soc_write.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a new variable for storing resources accessed subsequent to the one
accessed using request_mem_region, so the one accessed using
request_mem_region can be released if needed.
The resource variable names are also changed to be more descriptive.
This code is also missing some calls to iounmap.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@
if (E == NULL)
{
... when != if (E == NULL || ...) S1 else S2
when != E = E1
*E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure all mask bits are clear before setting new value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
DA7210 has three line outputs. OUT1 Left, OUT1 Right and OUT2 (mono).
This patch adds support for gain controls for these three line outs.
It also adds support for overall DAC gain control.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for DAPM covering all inputs and outputs
as well as ADC and DAC.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When a device has multiple speakers and still has the auto-mute support,
the driver copies line_outs[] to speaker_outs[]. And then it tries to
assign DACs for both. This ended up with the assignment only to the
primary DAC to all speakers.
This patch fixes the situation by checking the duplicated LO/SPK case
appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h,
use it instead of hardcoded (0x1 << 4) - 1 for the mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise calling ldo_regulator_remove() does not unregister regulator
and free memories.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the register map in datasheet, the registers are 8 bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
BIT 2:1
VMID_SEL[1:0] VMID Divider Enable and Select
00 = VMID disabled
01 = 2x40k Omh divider
10 = 2x240k Omh divider
11 = 2x5k Omh divider
To set VMID 2*240k, we should OR reg with 0x04 instead of 0x40.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds controls to set following ALC parameters,
- Max gain, Min gain, Noise gain, Attack rate, Release rate and delay
It also adds a switch to enable/disable noise suppression.
As per DA7210 data sheet, ALC and noise suppression can be enabled
only if certain conditions are met. This condition checks are handled
by simply using "_EXT" version of controls to capture change events.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwod <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for below set of controls,
(1) Mute controls for MIC, AUX and ADC
(2) Zero cross controls for head phone, AUX, INPGA and line out
(3) Head phone mode selection - class H or G
It also adds digital_mute() call back.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not that we have interrupt handling in the driver at the minute.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
According to the datasheet:
CHIP_MIC_CTRL 0x002A
BITS[9:8] BIAS_RESISTOR
0x0 = Powerd off
0x1 = 2.0 kohm
0x2 = 4.0 kohm
0x3 = 8.0 kohm
To set mic bias resistor, we need to update bits[9:8] of
SGTL5000_CHIP_MIC_CTRL register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
CHIP_MIC_CTRL 0x002A
BITS[9:8] BIAS_RESISTOR
0x0 = Powerd off
0x1 = 2.0 kohm
0x2 = 4.0 kohm
0x3 = 8.0 kohm
Thus SGTL5000_BIAS_R_MASK should be defined as 0x0300 instead of 0x0200.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't want to clear the prefix while we're creating the DAPM controls
for the device as the prefix is applied during control creation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
At least for the core controls, the optionally selected controls are still
added programatically.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Evaluation of larger quantities of material has provided new DCS codes
values to be applied for WM1811.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This is patch for Conexant codec of Intel HDA driver, adding new quirk
for Lenovo Thinkpad T520 and W520. Conexant autodetection works fine for
T520 (similar subsystem ID is used also in W520 model) and detects more
mixer features compared to generic (fallback) Lenovo quirk with
hardcoded options in Conexant codec.
Patch was activelly tested with Linux 3.0.4, 3.0.6 and 3.0.7 without any
problems.
Signed-off-by: Daniel Suchy <danny@danysek.cz>
Cc: <stable@kernel.org> [3.0+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous fix for the position-buffer check gives yet another
regression on a Dell laptop. The safest fix right now is to add a
static quirk for this device (and better to apply it for stable
kernels too).
Reported-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we have done bitwise NOT against the mask bits for the defines of
WM8900_REG_CLOCKING1_BCLK_MASK,
WM8900_REG_CLOCKING1_OPCLK_MASK and WM8900_LRC_MASK.
But we don't have the bitwise NOT against the mask bits for the defines of
WM8900_REG_CLOCKING2_DAC_CLKDIV,
WM8900_REG_CLOCKING2_ADC_CLKDIV and WM8900_REG_DACCTRL_AIF_LRCLKRATE.
It is error prone to mix the inconsistent meaning for different mask defines.
So lets make the defines for each mask to be corresponding to the bits
defines in datasheet. Don't add extra "bitwise NOT" to the defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After checking the datasheet, I think what we want to do here is to
clear the WM8900_REG_CLOCKING2_DAC_CLKDIV/WM8900_REG_CLOCKING2_ADC_CLKDIV/
WM8900_REG_DACCTRL_AIF_LRCLKRATE bits and then OR with div value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
Format Control (05h)
BITS[3:2]
FMT[1:0] Audio data format selection
00 = right justified mode
01 = left justified mode
10 = I2S mode
11 = DSP mode
BIT[4] LRP Polarity selec for LRCLK/DSP mode select
0 = normal LRCLK poalrity/DSP mode A
1 = inverted LRCLK poarity/DSP mode B
For SND_SOC_DAIFMT_DSP_A, we should set 0x000C instead of 0x0003.
For SND_SOC_DAIFMT_DSP_B, we should set 0x001C instead of 0x0013.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This patch add controls for setting cut-off for high pass and voice
filters of ADC and DAC. There are also switches to enable/disable
these filters.
Also removed hard coded, fixed values of these parameters used by
previous version of driver.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for ADC and DAC five band equalizers
available on DA7210 codec.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following sparse warnings:
sound/soc/tegra/tegra_das.c:215:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_das.c:237:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_pcm.c:370:32: warning: symbol 'tegra_pcm_platform' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The COEF #0 value represents a sort of device id, so it's supposedly
constant while operation. Better to use the cached value instead of
reading it at each time from the performance POV.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a static table for detecting the codec renames.
Also clean up the error paths in each patch_*() function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to have as less time between McPDM shutdown,
and power down of the DAC on the twl6040 codec as possible.
Request core to ignore the pmdown_time for the playback
stream.
Backround: with the McPDM protocol we are sendning not only
the pure audio stream, but OMAP McPDM also transmits
additional information (for example offset cancellation).
If McPDM is stopped prior to the DAC this information will
be not sent to the codec, which can result noise rendered
by the twl6040 codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this flag codec drivers can indicate that it is desired
to ignore the pmdown_time for DAPM shutdown sequence when
playback stream is stopped.
The DAPM sequence will be executed without delay in this case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch takes care of reserved bits of headphone volume
register by using correct volume range.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code defines AD193X_PLL_INPUT_MASK as (~0x6) which is quite
different from other MASK defines.
To make it consistent with other mask defines, define AD193X_PLL_INPUT_MASK
as 0x6 and change the code accordingly.
I think this change improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
This patch also includes a comment fix in wm8990_set_dai_pll(),
if freq_in and freq_out are 0, what we do is to clear WM8990_PLL_ENA bit.
Thus the comment should be "Turn off PLL".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If (fakepower & ((1 << WM8990_INMIXR_PWR_BIT) | (1 << WM8990_AINRMUX_PWR_BIT)))
is false, we should clear WM8990_AINR_ENA bits instead of WM8990_AINL_ENA.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If (fakepower & ((1 << WM8400_INMIXR_PWR) | (1 << WM8400_AINRMUX_PWR)))
is false, we should clear WM8400_AINR_ENA bits instead of WM8400_AINL_ENA.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If (fakepower & ((1 << WM8991_INMIXR_PWR_BIT)|(1 << WM8991_AINRMUX_PWR_BIT))))
is false, we should clear WM8991_AINR_ENA bits instead of WM8991_AINL_ENA.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the event handler is only used by the Earphone Driver, it is better
to rename it from twl6040_power_mode_event to twl6040_ep_drv_event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is better to switch HS Power Mode (if it was in low power mode) before
we enable the Earpiece driver. The switched off EP driver can filter out
noise coming from the Low Power to High Performance transition on the
HSL DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no limitation dictated by outputs or inputs regarding to the
selected PLL (LP/HP).
Remove the checks for this, and allow all path with any PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Capture is supported in all PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_DM365_EXTERNAL_CODEC does not exist, so it's a useless default.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ak4535_reg should be 8bit, but cache table is defined as 16bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
ak4642 register was 8bit, but cache table was defined as 16bit.
ak4642 doesn't work correctry without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched.
codec->hw_read is broken now.
Here we use below trick to avoid writing to reserved registers while resume.
Write the register default value to cache for reserved registers,
so the write to the these registers are suppressed by the cache
restore code when it skips writes of default registers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The audio_feature_info[] array should contain all entries for UAC2_FU_*,
but currently a few last entries are missing. Even though, the driver
tries to probe these entries in parse_audio_feature_unit() and may
access the range over the array. This patch fixes the bug by limiting
the loop size properly using ARRAY_SIZE() instead of a hard-coded
magic number.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds partial support for the Maschine controller by Native Instruments.
Supported now are the 1x1 MIDI interface and the 41 buttons, 11 endless
rotary encoders, and 16 pressure-sensitive drum pads. Still to work on are the
dimmable LEDs and the two monochrome screens.
Signed-off-by: William Light <wrl@illest.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There was a case where a newly-registered input device could be opened before
a necessary variable in the device structure was set. When code tried to use
the variable in the URB reply callback, it would cause an Oops.
This fix sets the aforementioned variable before calling input_register_device.
Signed-off-by: William Light <wrl@illest.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This typo caused headphone pins not to be initialized correctly.
BugLink: https://bugs.launchpad.net/bugs/871582
Reported-by: Effenberg
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The purpose of this patch is to remove a section of "bad" code that
assigns the last DAC to ports E or F in order to support notebooks
with docking in earlier days, around ALSA 1.0.19 - 21. This is not
necessary now and actually breaks some configurations that use these
ports as other devices. This have been tested on several different
configurations to make sure that it is working for different combinations.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In saarb_pm860x_init() and evb3_pm860x_init(), we call
pm860x_hs_jack_detect() and pm860x_mic_jack_detect() which in turn
calls pm860x_set_bits().
Thus make SND_SOC_SAARB and SND_SOC_TAVOREVB3 select MFD_88PM860X.
This patch fixes below build error if CONFIG_MFD_88PM860X is not configured.
LD .tmp_vmlinux1
sound/built-in.o: In function `pm860x_write_reg_cache':
last.c:(.text+0x29e9c): undefined reference to `pm860x_reg_write'
sound/built-in.o: In function `pm860x_set_bias_level':
last.c:(.text+0x29ecc): undefined reference to `pm860x_set_bits'
last.c:(.text+0x29f00): undefined reference to `pm860x_reg_write'
last.c:(.text+0x29f18): undefined reference to `pm860x_reg_write'
sound/built-in.o: In function `pm860x_read_reg_cache':
last.c:(.text+0x29f40): undefined reference to `pm860x_reg_read'
sound/built-in.o: In function `pm860x_probe':
last.c:(.text+0x2a034): undefined reference to `pm860x_bulk_read'
sound/built-in.o: In function `pm860x_codec_handler':
last.c:(.text+0x2a344): undefined reference to `pm860x_reg_read'
last.c:(.text+0x2a354): undefined reference to `pm860x_reg_read'
sound/built-in.o: In function `pm860x_mic_jack_detect':
last.c:(.text+0x2a450): undefined reference to `pm860x_set_bits'
sound/built-in.o: In function `pm860x_hs_jack_detect':
last.c:(.text+0x2a4d0): undefined reference to `pm860x_set_bits'
last.c:(.text+0x2a4f8): undefined reference to `pm860x_set_bits'
last.c:(.text+0x2a510): undefined reference to `pm860x_set_bits'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patchs adds support for following,
(1) DAI 20 and 32 bit word sizes
(2) DAI left and right justified formats
(3) DAI slave mode
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both Headset DAC need to be turned on/off at the same time before
any of the output drivers are enabled (HS Left/Right, Earpiece).
Move the HS DAC enable code to sequenced DAPM_SUPPLY, and attach
it to the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl6040 have two vibra output drivers.
They can be operated with audio stream coming through
the PDM interface (fifth channel).
The vibra outputs can be controlled via the input/FF
driver as well.
Selection between the two mode is implemented within
the codec driver, the input/FF driver can only operate if
the routing is set to "Input FF".
Changing from "Input FF" to "Audio PDM" mode is protected
as well: The switchin can only be done, if there is no
running effect from the input/FF.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We set hw_params callback for wm8994_aif3_dai_ops to wm8994_aif3_hw_params.
Thus no need to check wm8994-aif3 in wm8994_hw_params.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after multi-component patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5100 includes an advanced, low power, accessory detect subsystem
capable of detecting both accessory presence and button presses while
the device is in an ultra low power mode. Implement initial support for
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is currently named "TVL" instead of "TLV".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8983 can be reset by performing a write of any value to
the software reset register.
To avoid writing to the software reset register while resume,
we should write the same value in wm8983_reg_defs to software
reset register in wm8983_probe().
The write to the reset register is suppressed by the cache
restore code when it skips writes of default registers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes and static controls via the
snd_soc_card struct to core. In this way the machine driver
does not need to handle the DAPM widgets/routes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Widgets are connected by default.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Widgets are connected by default.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass the DAPM widgets/routes via the snd_soc_card struct
to core.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to call soc_dapm_sync at init time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The rpcm_file parameter is never used in current ALSA code, so remove
it to make it cleaner.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Michael Opdenacker <michael.opdenacker@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to snd_soc_cache_sync for sync reg_cache with the hardware.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We really should be doing this in the core, not in a driver...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
The ASoC code always uses -1 as the error code due to reporting errors in
band with the value. Ensure we don't confuse anything by making sure we
don't pass actual error codes back into the rest of the code on read.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The number of connected input and output endpoints for a given widgets
can't change during a DAPM run so there is no need to redo the recursion
through branches of the tree we've already visited. Doing this on one of
my test systems gives an improvement of:
Power Path Neighbour
Before: 63 607 731
After: 63 141 181
which scales up well as more widgets are involved in paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handling of user control elements was implemented for all types except
ENUMERATED. This type will be needed for the device-specific mixers of
upcoming FireWire drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This ensures none of the rest of the code ever encounters a widget which
does not have a power check function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.
OMAP drivers are omitted as I know Peter already has patches for them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we only have one sync during the initial startup of the card by
making snd_soc_dapm_sync() a noop on non-instantiated cards. This avoids
any bounces due to things like jacks reporting their initial state on
partially initialised cards. The callers that don't also get called at
runtime should just be removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Checking the pdata-flags used 'or', so the check is always true. Use 'and' to
correctly mask the flags.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We synchronise jack state on startup - when we do that make sure that we
have set up all the DAPM widgets first in case we end up touching any of
the partially set up widgets when syncing the jack pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The snd_soc_*_volsw_2r functionality has been merged to
*volsw callbacks.
Few places still used the get, or put variant of volsw_2r,
replace those with the corresponding *_volsw.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit ef18beded8 introduced a
mechanism to assign the previously used slot for the next reopen of a
PCM stream. But the PCM device number isn't always unique (it may
have multiple substreams), and also the code doesn't check the stream
direction, thus both playback and capture streams share the same
device number.
For avoiding this conflict, make a unique key for each substream and
store/check this value at reopening.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the speaker outputs are more than the headphone outputs, it implies
that the system has surround speakers while the headphones are only for
monitoring the front. In such a case, it's better to put speakers as
the primary outputs so that the driver can build up and keep the
surround setup. Otherwise the system will pick up the headphone as
primary, and offers less channels than the speakers do support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since hda_proc.c is now the only user of snd_print_pcm_rates(), better to
put it back locally to hda_proc.c and revert to the old style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SAD sampling rate information reported in
/proc/asound/cardX/eldX is incorrect due to a mismatch
between HDA and HDMI frequencies. Add new routine to provide
relevant values.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eliminate below build warning:
CC sound/soc/codecs/wm9090.o
sound/soc/codecs/wm9090.c: In function 'wm9090_probe':
sound/soc/codecs/wm9090.c:550: warning: unused variable 'wm9090'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These functions are removed in commit f0fba2ad
"ASoC: multi-component - ASoC Multi-Component Support".
Let's remove the leftover function declaration in header file.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Let the user know, that the callback has been called with unexpected
register parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ASoC core now have one callback function, which can handle
single, and double register mixer controls.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the put_volsw/put_volsw_2r in one function.
To avoid build breakage in twl6040 keep the
snd_soc_put_volsw_2r as define, and map it snd_soc_put_volsw.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the get_volsw/get_volsw_2r in one function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle the info_volsw/info_volsw_2r in one function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoid using the mc->rreg to identify the 2r type of gain control.
Introduce a variable to track this.
This change is needed to avoid breakage with the upcoming volsw volsw_2r
merger.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The custom get_volsw does not need to call any core get_volsw calls,
since we are returning the shadow values for the gains.
Return -EINVAL in the unlikely event, if the function has been called
for unhandled control. This way we can remove one check in the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the macros for controls require custom get/put function.
This is to make sure that the soc_mixer_control is used
consistently among the drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similar to Line Out, these constants form the base for future
patches enabling input jack reporting for Line in jacks.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we run out of DACs when trying to assign a DAC to a secondary
headphone, prefer the DAC of the first headphone to the primary
(usually line out) DAC.
BugLink: http://bugs.launchpad.net/bugs/845275
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We don't really care how many widgets a supply is supplying, we just care
if the number is non-zero. This didn't actually produce any improvement
in the test cases I've been using but seems obviously sensible enough that
I'm pushing it out anyway.
We could do a similar thing for other widgets but this may be unhelpful
for further refactorings Liam was working on aiming to allow us to
identify connected audio paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The whole point of supply widgets is that they aren't inputs to their
sinks so a state change in a supply should never affect the state of the
widget being supplied and we don't need to mark them as dirty.
Power Path Neighbour
Before: 69 727 905
After: 63 607 731
This is particularly useful where supplies affect large portions of the
chip (eg, a bandgap supplying the analogue sections).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some widgets will get power_check() run on them more than once during a
DAPM run, most commonly due to supply widgets checking to see if their
consumers are powered up. It's wasteful to do this so cache the result
of power_check() during a run. For one system I tested this on I got an
improvement of:
Power Path Neighbour
Before: 106 970 1186
After: 69 727 905
from this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Help diagnose why we're checking widgets by providing some logging when
we first dirty them. This should possibly be a trace point if it's useful
but can be absurdly verbose if enabled, we can always change it later if
desired.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'fix/asoc' of git://github.com/tiwai/sound:
ASoC: omap_mcpdm_remove cannot be __devexit
ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC
ASoC: use a valid device for dev_err() in Zylonite
If two widgets are not currently connected then there is no need to
propagate a power state change between them as we mark the affected
widgets when we change a connection. Similarly if a neighbour widget is
already in the state being set for the current widget then there is no
need to recheck.
On one system I tested this gave:
Power Path Neighbour
Before: 114 1066 1327
After: 106 970 1186
which is an improvement, although relatively small.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to reduce the number of DAPM power checks we run keep a list of
widgets which have been changed since the last DAPM run and iterate over
that rather than the full widget list. Whenever we change the power state
for a widget we add all the source and sink widgets it has to the dirty
list, ensuring that all widgets in the path are checked.
This covers more widgets than we need to as some of the neighbour widgets
won't be connected but it's simpler as a first step. On one system I tried
this gave:
Power Path Neighbour
Before: 207 1939 2461
After: 114 1066 1327
which seems useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're not actually doing any dynamic power management based on connection
and output drivers (which are pretty much the same thing) are marked as
unconditionally connected already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We've got the same code in two different places, let's have it in a single
place instead.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Future patches will try to reduce the number of widgets we check on each
DAPM run but we're still going to need to look and see if the devices is
on at all so we can manage the overall device bias. Move these checks out
into the main dapm_power_widgets() function so we don't have to think about
them for now.
Once we're doing more incremental updates it'll probably be worth using
refcounts for each bias level to avoid having to do the sweep over all
widgets but that's not going to be where the big performance wins are.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Split the decision about what the new power should be out from the
implementation of that decision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -EINVAL in the unlikely event, if the function has been called
for unhandled control. This way we can remove one check in the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not required after commit 8d50e447
"ASoC: Factor out I/O for Wolfson 8 bit data 16 bit register CODECs"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Writing to WM8971_RESET resets all registers to the default state.
Thus we should avoid writing to WM8971_RESET on resume.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
