commit 365ec8b616 upstream.
Limit the fsl,pfuze-support-disable-sw to the pfuze100 and pfuze200
variants.
When enabling fsl,pfuze-support-disable-sw and using a pfuze3000 or
pfuze3001, the driver would choose pfuze100_sw_disable_regulator_ops
instead of the newly introduced and correct pfuze3000_sw_regulator_ops.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Fixes: 6f1cf5257a ("regualtor: pfuze100: correct sw1a/sw2 on pfuze3000")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201110174113.2066534-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=Ot99
-----END PGP SIGNATURE-----
Merge tag 'v5.4.67' into 5.4-2.2.x-imx
This is the 5.4.67 stable release
This updates the kernel present in the NXP release imx_5.4.47_2.2.0 to the
latest patchset available from stable korg.
Base stable kernel version present in the NXP BSP release is v5.4.47.
Following conflicts were recorded and resolved:
- arch/arm/mach-imx/pm-imx6.c
NXP version has a different PM vectoring scheme, where the IRAM bottom
half (8k) is used to store IRAM code and pm_info. Keep this version to
be compatible with NXP PM implementation.
- arch/arm64/boot/dts/freescale/imx8mm-evk.dts
- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
NXP patches kept to provide proper LDO setup:
imx8mm-evk.dts: 975d8ab07267ded741c4c5d7500e524c85ab40d3
imx8mn-ddr4-evk.dts: e8e35fd0e759965809f3dca5979a908a09286198
- drivers/crypto/caam/caamalg.c
Keep NXP version, as it already covers the functionality for the
upstream patch [d6bbd4eea2]
- drivers/gpu/drm/imx/dw_hdmi-imx.c
- drivers/gpu/drm/imx/imx-ldb.c
- drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
Port changes from upstream commit [1a27987101], which extends
component lifetime by moving drm structures allocation/free from
bind() to probe().
- drivers/gpu/drm/imx/imx-ldb.c
Merge patch [1752ab50e8] from upstream to disable both LVDS channels
when Enoder is disabled
- drivers/mmc/host/sdhci-esdhc-imx.c
Fix merge fuzz produced by [6534c897fd].
- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
Commit d1a00c9bb1 from upstream solves the issue with improper error
reporting when qdisc type support is absent. Upstream version is merged
into NXP implementation.
- drivers/net/ethernet/freescale/enetc/enetc.c
Commit [ce06fcb6a6] from upstream merged,
base NXP version kept
- drivers/net/ethernet/freescale/enetc/enetc_pf.c
Commit [e8b86b4d87] from upstream solves
the kernel panic in case if probing fails. NXP has a clean-up logic
implemented different, where the MDIO remove would be invoked in any
failure case. Keep the NXP logic in place.
- drivers/thermal/imx_thermal.c
Upstream patch [9025a5589c] adds missing
of_node_put call, NXP version has been adapted to accommodate this patch
into the code.
- drivers/usb/cdns3/ep0.c
Manual merge of commit [be8df02707] from
upstream to protect cdns3_check_new_setup
- drivers/xen/swiotlb-xen.c
Port upstream commit cca58a1669 to NXP tree, manual hunk was
resolved during merge.
- sound/soc/fsl/fsl_esai.c
Commit [53057bd4ac] upstream addresses the problem of endless isr in
case if exception interrupt is enabled and tasklet is scheduled. Since
NXP implementation has tasklet removed with commit [2bbe95fe6c],
upstream fix does not match the main implementation, hence we keep the
NXP version here.
- sound/soc/fsl/fsl_sai.c
Apply patch [b8ae2bf5cc] from upstream, which uses FIFO watermark
mask macro.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 6f1cf5257a ]
PFUZE100_SWB_REG is not proper for sw1a/sw2, because enable_mask/enable_reg
is not correct. On PFUZE3000, sw1a/sw2 should be the same as sw1a/sw2 on
pfuze100 except that voltages are not linear, so add new PFUZE3000_SW_REG
and pfuze3000_sw_regulator_ops which like the non-linear PFUZE100_SW_REG
and pfuze100_sw_regulator_ops.
Fixes: 1dced996ee ("regulator: pfuze100: update voltage setting for pfuze3000 sw1a")
Reported-by: Christophe Meynard <Christophe.Meynard@ign.fr>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592171648-8752-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Some registers on pfuze3000 will lost after exit from LPSR, need restore them,
otherwise system may reboot with below command after system enter LPSR one time:
root@imx7d_all:~# echo enabled > /sys/class/tty/ttymxc0/power/wakeup
root@imx7d_all:~# echo mem > /sys/power/state
because LDOGCTL not recover as 1. Add 'fsl,lpsr-mode' property to this case,
please add this property if your board support LPSR mode as imx7d-12x12-lpddr3-arm2
board.
Signed-off-by: Robin Gong <b38343@freescale.com>
(cherry picked from commit 4aa2a2a92814433d76de1bf6ae8902e46fb87961)
In function pfuze100_regulator_probe(), variable "val" could be
initialized if regmap_read() fails. However, "val" is used to
decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20190929170957.14775-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently supports coin cell / super cap charging, so
this patch extends it to support PF0100.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some boards the SoC can use one pin "PMIC_STBY_REQ" to notify th PMIC
about state changes. In this case internal state of PMIC must be
preconfigured for upcomming state change.
It works fine with the current regulator framework, except with the
power-off case.
This patch is providing an optional pm_power_off_prepare handler
which will configure standby state of the PMIC to disable all power lines.
In my power consumption test on RIoTBoard, I got the following results:
power off without this patch: 320 mA
power off with this patch: 2 mA
suspend to ram: 40 mA
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulators on pfuze100.
Based on commit 5fe156f1ca ("regulator: pfuze100: add enable/disable for
switch") which is reverted due to boot regressions by commit 464a5686e6
("regulator: Revert "regulator: pfuze100: add enable/disable for switch"").
Disabling the switch regulators will only be done if the user specifies
"fsl,pfuze-support-disable-sw" in its device tree to keep backward
compatibility with current dtb's [1].
[1] https://patchwork.kernel.org/patch/10490381/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 5fe156f1ca.
Commit 5fe156f1ca ("regulator: pfuze100: add enable/disable for switch")
causes boot regression on some platforms such as imx6sl-evk and
imx6sll-evk.
After this commit the SW4 regulator will be turned
off and since it supplies the DDR voltage on these boards, a
kernel hang is observed.
Revert it to avoid breaking old dtb's.
Fixes: 5fe156f1ca ("regulator: pfuze100: add enable/disable for switch")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This extends the pfuze100 driver with pfuze3001 support.
Latest datasheet:
https://www.nxp.com/docs/en/data-sheet/PF3001.pdf
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We now pass a GPIO descriptor to the core instead of a global
GPIO number, if this descriptor is NULL the GPIO line is not
used. Just delete the assignment of an invalid GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If is_enabled() is not defined, regulator core will assume
this regulator is already enabled, then it can NOT be really
enabled after disabled.
Based on Li Jun's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulator on pfuze100.
Based on Robin Gong's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pfuze3000 datasheet(Rev.9.0) from:
https://www.nxp.com/docs/en/data-sheet/PF3000.pdf
updates sw1a's voltage range, the settings for 1.450V and 1.475V
are replaced with 1.8V and 3.3V:
5b'11110 1.450 (SW1B), 1.8 (SW1A/SW1AB)
5b'11111 1.475 (SW1B), 3.3 (SW1A/SW1AB)
the voltage calculation using steps is NOT available for sw1a now,
use voltage table instead.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PF0200 coin cell/super capacitor charger which works as
a current limited voltage source via the LICELL pin. When VIN goes below
a certain threshold LICELL is used to provide power for VSNVS which is
usually used to hold up secure non-volatile storage and the real-time
clock on the SoC.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/pfuze100-regulator.o
text data bss dec hex filename
3552 12528 16 16096 3ee0 regulator/pfuze100-regulator.o
File size after: drivers/regulator/pfuze100-regulator.o
text data bss dec hex filename
4576 11496 16 16088 3ed8 regulator/pfuze100-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust the MODULE_DESCRIPTION() text to also include the PFUZE3000
as a supported device.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should better not use a global 'struct pfuze_regulator' variable,
as this could cause problems if multiple regulator chips are used.
Place it inside the private struct instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has a I2C device id table that is used to create the modaliases
and also "pfuze100-regulator" is not a supported I2C id, so is never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code has .enable_reg and .enable_mask settings, but the implementation
for corresponding callbacks are missing. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously, the PFUZE100 would try to allocate gpio0 io0 because
config.ena_gpio defaults to 0, which can be a valid GPIO. To prevent this
from happening, set this parameter to -EINVAL.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SWB regulators have the ability to be turned on and off. Add
enable/disable support for these regulators.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also remove PFUZE_NUM to avoid below build warnings:
CC [M] drivers/regulator/pfuze100-regulator.o
drivers/regulator/pfuze100-regulator.c:86:2: warning: excess elements in array initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:86:2: warning: (near initialization for 'pfuze_device_id') [enabled by default]
drivers/regulator/pfuze100-regulator.c:93:2: warning: excess elements in array initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:93:2: warning: (near initialization for 'pfuze_dt_ids') [enabled by default]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
support pfuze200 chip which remove SW1C and SW4 based on pfuze100.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If of_node_get() fails, we should return an error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit d7857c42 (regulator: pfuze100: Use of_get_child_by_name) we get
the following probe failure:
pfuze100-regulator 1-0008: Full layer: 1, Metal layer: 0
pfuze100-regulator 1-0008: FAB: 0, FIN: 0
pfuze100-regulator 1-0008: regulators node not found
pfuze100-regulator: probe of 1-0008 failed with error -22
Now that of_get_child_by_name() is used we should adjust the device_node pointer
'np' to not get the parent node anymore.
Suggested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
'lay' is not very meaningful, so use it 'layer' instead to let the dev_info()
clearer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch error and warning:
ERROR: switch and case should be at the same indent
#311: FILE: drivers/regulator/pfuze100-regulator.c:311:
+ switch (value & 0x0f) {
[...]
+ case 0x8:
[...]
+ case 0x0:
[...]
+ default:
WARNING: line over 80 characters
#312: FILE: drivers/regulator/pfuze100-regulator.c:312:
+ /* Freescale misprogrammed 1-3% of parts prior to week 8 of 2013 as ID=8 */
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
prior to week 08 of 2013 Freescale misprogrammed between 1 and 3% of
PFUZE1000 parts with a ID=0x8 instead of the expected ID=0x0
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
According to the datasheet, the address of FABID is 0x4. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
max_register should be register count - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify the equation to calculate ramp_delay.
Below equations are equivalent:
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 50000 / (4 * ramp_delay);
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 12500 / ramp_delay;
So we don't need to read BIT6 of rdev->desc->vsel_reg for applying different
equations.
Also use rdev->desc->vsel_reg instead of run-time calculate register address.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code adjust min_uV and uV_step but missed adjusting the n_voltages
setting.
When BIT6 is clear:
n_voltages = (1975000 - 400000) / 25000 + 1 = 64
When BIT6 is set:
n_voltages = (3300000 - 800000) / 50000 + 1 = 51
The n_voltages needs update because when BIT6 is set 0x73 ~ 0x7f are reserved.
When using regulator_list_voltage_linear, the n_voltages does matter here
because wrong n_voltages setting make the equation return wrong result.
e.g. if selector is 63, regulator_list_voltage_linear returns
800000 + (50000 * 63) = 4000000
It should return -EINVAL if the selector is in the range of 51 ~ 63.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All table based voltage list have ascendant order.
Use regulator_map_voltage_ascend for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since this is a i2c driver, use i2c_[set|get]_clientdata instead of
dev_[set|get]_drvdata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Andrey Zhizhikin