The CUST_SCRATCHPAD_CSR register is used for marking if FW cleanup is
needed. This is used in a crash kernel scenario. Do no use this register as
it is not available for some functions. Instead, always issue an FLR when
a function is probed *except* when VFs are preset (enabled in the previous
PF load).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the PCI MRRS to a value of 4096 (overriding the system decided
value) had provided perf improvement in TX.
But, IBM has provided feedback that on POWER platforms, this value is set
by the system firmware, and drivers modifying this value can cause
unpredictable results (like EEH errors.) So, backing off this change.
On POWER7 platforms most slots, it seems, do get a MRRS of 4096.
This patch reverts the following commit:
"be2net: Modified PCI MaxReadReq size to 4096 bytes"
commit 5a56eb10ba.
Suggested-by: Brian King <bjking1@us.ibm.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- get rid of 2 unused arguments to the routine and some unused code
- don't use the term "vlan_tag" in place of "vid" as they are different
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_vid_config() is called from be_setup() to replay config cmds after
a card reset. Skip calling it when no vlans are configured.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to declare the opmode ops
as extern since they're now dynamically
registered.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the RF config is done for all devices,
there's no need to keep a separate function
that is called for all devices, move it into
the general NIC config function.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should also configure the PHY version in the
CSR_HW_IF_CONFIG_REG register for 1000 series
devices, not just for the other devices.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7c5ba4a830 ("iwlwifi: move queue
watchdog into transport") introduced the named constant
'IWL_WATCHHDOG_DISABLED'. Rename it to 'IWL_WATCHDOG_DISABLED'.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The EEPROM reading/parsing code is all mixed in
the driver today, and the EEPROM is parsed only
when we access data from it. This is problematic
because the NVM needs to be parsed and that is
independent of reading it. Also, the NVM format
for new devices will be different and probably
require a new parser.
Therefore refactor the reading and parsing and
create two independent components. Reading the
EEPROM requires direct hardware accesses and
therefore access to the transport, but parsing
is independent and can be done on an NVM blob.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was missing. Fix the mask of the REV_TYPE on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes noticed this was completely messed up.
We got confused between masks and bit position.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few cases we need to set a value in
a certain mask inside a register, add the
function iwl_set_bits_mask() to make such
code easy.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports will have different needs: New tranports
need headroom for their own use before the Tx cmd. So allocate
the Tx cmd pool in the transport and give it a unique name
based on dev_name.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Although we don't use bit 24, this bit is valid, but bit 23
is not. Update the mask accordingly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to enable / disable Tx queues in HW
dynamically. So this function is no longer related to AGG
only. It can do the job for any queue, even AC ones. Change
the name to better reflect its role.
Also use the new function to configure the AC / CMD queues
in tx_start.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to enable / disable Tx queues in HW
dynamically. So this function is no longer related to AGG
only. It can do the job for any queue, even AC ones. Change
the name to better reflect its role.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This functions does the job so use it instead of duplicating
the code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The DMA channels of the FH should be activated after the
configuration of the SCD queues too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduler can issue an interrupt when moving the read
pointer. To get this interrupt, the driver needs to
configure what queue can issue an interrupt when its read
pointer moves in the scheduler: this is the SCD_INT_MSK.
The driver also needs to enable the interrupt in
CSR_INT_MASK (bit CSR_INT_BIT_SCD).
Since we don't enable the scheduler interrupt in
CSR_INT_MASK, there is no point in requesting an interrupt
from the scheduler: it will be masked anyway. So don't
configure the scheduler to issue interrupts at all.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to dynamically fill the HT40
band bitmap as it's a device parameter, just
put it into the HT configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to copy the same code for all
devices since none of the 5000 series devices
(that don't have the RX SISO override) don't
set the rx_with_siso_diversity variable.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're working on another mode/driver
inside iwlwifi, move the current one into a
subdirectory to more cleanly separate the
code. While at it, rename all the files.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 asks us to do HT40, it'll not do so
on a channel that we marked as not having HT40+/-
with IEEE80211_CHAN_NO_HT40PLUS (or MINUS). Thus,
there's no need to verify it again in the driver.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Structure the code a bit more and move all PCIe code
including the hardware configuration files into a
PCIe specific subdirectory.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The STATUS_SCAN_HW is set before calling iwlagn_set_pan_params
(used as an input to calculate slot time allocation). The bit needs
to be cleared in case sending the command fails.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We know whether we received a frame in GF format
or not, add it to the radiotap information.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In channel switch, instead of relying on our internal
channel database, just use the mac80211 channel that
we filled with that information on startup.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of iterating our own channel list,
use the mac80211 channel list since that's
already processed per band and thus makes
for less code.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 will never set, switch to, or scan on an
invalid channel, so remove the code to validate
the channels against the driver channel list.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 guarantees that the channel pointer is
always valid, so we can use that instead of our
own channel list.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of functions were temporarily made non-static
for experimental work, make them static again now.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a remain on channel request from mac80211 is followed by
a request to tx a mgmt frame offchannel, it is possible that
the remain on channel expires before the device reported the
tx status for the frame. This causes a race condition in
mac80211.
To fix this, delay the ROC notification to mac80211 until the
device reported the Tx status for all frames in the aux queue.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that the BSS context is not active (for example
when the current mode is set to GO), or that the vif->type is
different than station. In such a case we cannot
call mac80211 to report the average rssi for the interface
(the function assumes that the vif is valid and that the type
is station).
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx
stripping is disabled. This results in passing frames up the stack
which do not have the 802.1Q tag stripped but have the tci bits
set as if it was.
Working around this with a check for the feature flag bit. I
would welcome any better ideas or a pointer to exactly which
bits in the hardware register need to be cleared to get the
IXGBE_RXD_STAT_VP bit to be set per data sheet.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB can be used independent of if RX VLAN stripping is enabled
or disabled so remove erroneous check.
Also enable or disable VLAN stripping when features are applied so
hardware and feature flags are in sync.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 44abd5c127 introduced NULL pointer
dereferences when attempting to access the check_reset_block function
pointer on 8257x and 80003es2lan non-copper devices.
This fix should be applied back through 3.4.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We separate reading of device's eeprom content from writing it back
to the device's sram.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a debugging log when using shadow
registers. Also fix a minor typo in this
connection.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly clean up indentation around parentheses
after if, function calls, etc. and also a few
unneeded line breaks and some other things.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is a library to be used by multiple
opmodes, so move it into the iwlwifi module.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the next step in splitting up the driver,
making the uCode API dependent pieces of it live
in separate modules. Right now there's only one
so it's not user-selectable, but we're actively
working on more.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is common, not uCode API specific, so move
it to the transport together with the command
header struct definition.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is intended to be set whenever wakeup will be
needed upon suspend, not only when suspending, so
use the new callbacks to set it then.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is needed by other transports besides PCIe, thus
moving to a common location.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches suggested adding the __printf attribute
to the __iwl_dbg function to check arguments; add it
to all of the logging functions (err, warn, info, dbg
and crit.)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We missed passing an argument to the
debug print. Fix it.
Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug prints were wrong and buggy. The HW pointer wasn't printed
correctly, it was mixed up with the pointer to the rxbuf.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This chip is used at least by the D-Link DWA-525 adapter.
Signed-off-by: Alex Villac<ED>s Lasso <a_villacis@palosanto.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This returns many of the values that formerly could
only be obtained from debugfs. This should be an
improvement when trying to access these counters
programatically. Currently this support is only
enabled when DEBUGFS is enabled because otherwise
these stats are not accumulated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we provide excess buffer size for 'simple_read_from_buffer'
for modal EEPROM dump. This results in trailing NULL bytes
at the end of EEPROM dump, fix this.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reported-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Holger Schurig <holgerschurig@gogglemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is potentially called with NULL pointers, for example, look at
brcmf_c_prec_enq(). Since it's a free() function, probably people
expect it to handle NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code causes a static checker warning because "pi" gets dereferenced
before it is checked. The dereference is inside the write_phy_reg()
function which is called from wlc_phy_write_txmacreg_nphy().
This code is only called from wlc_phy_init_nphy() and "pi" is a
valid pointer so we can remove the check for NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
D-Link DWA-123 rev A1
Signed-off-by: Albert Pool<albertpool@solcon.nl>
Cc: <stable@vger.kernel.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Or at least plug another gapping hole. Apparrently hw desingers only
moved the bit field, but did not bother ot re-enumerate the planes
when adding support for a 3rd pipe.
Discovered by i-g-t/flip_test.
This may or may not fix the reference bugzilla, because that one
smells like we have still larger fish to fry.
v2: Fixup the impossible case to catch programming errors, noticed by
Chris Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull two scsi target fixes from Nicholas Bellinger:
"The first is a small name-space collision fix from Stefan for the new
sbp-target / ieee-1394 code, and second is the FILEIO backend
conversion patch to always use O_DSYNC by default instead of O_SYNC as
recommended by hch. Note the latter is CC'ed stable."
* '3.5-merge-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/file: Use O_DSYNC by default for FILEIO backends
sbp-target: rename a variable to avoid name clash
Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus reported that due to mac80211 failing to register
the device (due to WoWLAN) his machine crashed etc. as
we double-freed the vmalloc() firmware area. His patch
to fix it was very similar to this one but I noticed
that there's another bug in the area: we complete the
completion before starting, so since we're running in
a work struct context stop() could be called while in
the middle of start() which will almost certainly lead
to issues.
Make a modification similar to his to avoid the double-
free but also move the completion to another spot so it
is only done after start() either finished or failed so
that stop() can have a consistent state.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull embedded i2c update from Wolfram Sang:
"This only contains one new driver which had multiple dependencies
(pinctrl, i2c-mux-rework, new devm_* functions), so I decided to wait
for rc1. Plus, it had to wait a little for the ack of a devicetree
maintainer since the bindings were not trivial enough for me to pass
through.
So, given that, I hope there is still something like the "new driver
rule", so we could have the driver in 3.5 and people can start using
it. That would make merging support for some boards easier for 3.6
since the dependency on this driver is gone then."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: Add generic I2C multiplexer using pinctrl API
In some multi role scenarios the driver might send multi
roc requests without sending a croc first, the fw queues
those requests and starts service the next roc request as
soon as the driver sends a croc for the previous one. So,
if the fw rocs on channel X and driver asks to roc also
on channel Y, the fw will not start service Y (and will
not send roc complete event for this request) until the
driver releases the fw with croc X.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The beacon early termination is not relevant for
high basic rates, which doesn't contribute
anything to the PS and only adds unnecessary FW
work.
Enable BET only if the basic rate is less than 9
Mbps.
Signed-off-by: Ziv Riesel <zivriesel@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Wrong fm_coex parameters were set during wl18xx
init phase, fix it.
Signed-off-by: Ziv Riesel <zivriesel@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Wrong fm_coex parameters were set during wl12xx
init phase, fix it.
Signed-off-by: Ziv Riesel <zivriesel@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This BUG_ON also ignored the INTENDED_FW_RECOVERY flag. This would
result in a BUG() when using the bug_on_recovery module parameter during
multi-role.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some cases, the ROC_COMPLETE event might exceed the
current timeout (750 msec). Increase it to 1 sec.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On CHANGE_CHANNEL indication, we should flush all the
queued tx frames, so they will be sent on the correct
(current) channel.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In the enum conf_tx_ac CONF_TX_AC_ANY_TID should
be 0xff to match the firmware's implementation.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The polarity should be set before the firmware is loaded
since the firmware touches the same register. Access
of the firmware and driver to the same register will
cause a collision since there is no exclusion scheme.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.
In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the ht_cap IE per-band, so we can configure different
params to BG and A bands (we currently don't support MIMO
on A band)
[Small fix for rx_highest - Arik]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add a dependency on mac80211 in Kconfig, and also replace some spaces
with tabs.
Reported-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21)
we are supporting 3 RX BA sessions, this change is to support this
new ability.
Signed-off-by: Assaf Azulay <assaf@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Modify default parameters to reduce firmware BSS lose
probability in congested environment.
[Applied to 18xx configuration as well - Arik]
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make sure the deauth bcast gets sent
[Make sure we are AP as well before the flush - Arik]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Multicast management frames (e.g. global deauth)
should be sent out on the bcast link, rather than
the global, which should be used only for pre-added
stations (e.g. for auth/assoc resp).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We can't use cancel_delayed_work_sync() from functions that take the
wl->mutex, since connection_loss_work also takes the mutex. This might
result in a deadlock. Restructure the code so the work is synchronously
canceled before taking the mutex.
Avoid a bug where we would indefinitely delay the connection loss
indication by re-queuing the connection loss work on consecutive beacon
loss events.
Cc: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In patch d7b63b9fc7 we have raised the dynamic
PS timeout to 200ms to improve user experience. Re-apply the change,
since it was reverted in the wlcore split.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The "static" modifier was mistakenly forgotten for some functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke
support for wl127x chips.
When we moved the identify_chip operation to an earlier stage (ie. to
the probe function), we broke wl127x support because during HW init we
would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN.
To avoid this, set this quirk in the identify_chip operations and only
force it to be unset if the bus module doesn't support it. We were
doing the opposite and setting the flag if the bus module supports it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
as tcp check sum is going to be removed from firmware, and as
there is a problem with getting dns in security when checksum is
enabled, it was decided to disable it by default.
for none security modes it can be enabled by module paramenter.
Signed-off-by: Assaf Azulay <assaf@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some of the structures were updated, other structures had a few
missing values and a few new ones were added. Change the driver
structs accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Now the firmware can support TX block ack sessions with 64 frames.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer
during iperf. This is the optimal for the firmware. Thus, increase
the buffer size by one page.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Instead of adding more files from the lower drivers into the same
directory in debugfs as wlcore, we now add a subdirectory for the
lower driver. This makes things a bit easier, because we can quickly
see where the debugfs entry is implemented and what is specific to the
lower driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Yet another temporary module parameter requested by the firmware team.
This will be replaced by the conf binary.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We use hardcoded values for the different board types. In some cases
we may need to override the defaults, so export the values as module
params. If not defined, the defaults for the specified board type
will be used.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
With more recent PHY firmware versions (>8.1.0.0.116), we need to use
the correct value for the pwr_limit_reference_11_abg parameter when
setting the mac_and_phy options.
For now we use a hardcoded 0xc8 as the value. This will be moved to
the configuration binary when it gets implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We were setting all the rates bits when starting the AP role. Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates). This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
If the wl18xx module is loaded with ht_mode=wide (the default), we
shouldn't use MIMO rates when the channel type is not HT40. Fix this
by checking the ht_mode before deciding which rates to used.
Additionally, set the ht_mode parameter explicitly to "wide" as the
default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases it may be useful for debugging to check what is the
status of the interrupt register when a hardware recovery happens.
Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when
recovery starts.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl18xx firmware writes the PHY firmware version in the static
data. Add an operation to parse the static data and print the PHY
firmware version when booting.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl18xx firmware has more information in the static_data than
wl12xx. To be able to parse that in an abstracted way, this patch
adds a priv area to the static data struct and an operation that
allows the lower driver to parse it if necessary.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the operations that are necessary to fetch the
wl18xx-specific FW statistics and export them in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the operations that are necessary to fetch the
wl12xx-specific FW statistics. Re-add some of the code removed from
wlcore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add a macro to make it easy to print arrays from the FW statistics
array in debugfs. At the same time, increase the buffer size so
arrays fit more easily.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The FW statistics differ from hardware to hardware. This commit
prepares for hardware-specific implementation of the FW statistics
debugfs entries.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set. To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When the data rates change, we get BSS_CHANGED_BASIC_RATES. At this
point, we should update all the templates to match the new rates. We
were changing some of the templates, but the beacon and the probe
response templates were missing.
[Remove redundant min_rate variable - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
There are some problems with MCS_13 in PG 1.0 hardware. So we disable
it when PG 1.0 is detected.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We can do get the HW information and identify the chip already at
probe time. This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When allocating the fw_status structure, the space for the
lower-driver private area was missing. This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Since the most common board we're using now is an HDK board, change
the default board_type to hdk.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.
Reported-by: Dror Erez <drorer@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases we may want to dump all the SDIO data in order to get
detailed information for debugging the communication with the
firmware.
Add printks to dump the data and a module parameter to enable/disable
it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now. 11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the get_mac operation in order to fetch the BD_ADDR from fuse ROM,
so that we can derive the WLAN MAC addresses from it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The number of RX packet descriptors may vary from chip to chip and
in different firmware versions. Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure. To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.
[Changed the STATUS_LEN macro to be placement agnostic - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC. Add some module
parameters that allow changing that.
In the future this will come from the "NVS" file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Currently, all HDK boards use low_band_component_type 0x06. In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the correct FW name for PLT (which is the same as the normal
firmware) and implement the plt_init operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
PLT mode needs to be initialized differently for each chip. This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add more board types and remove a now unneeded write to SCR_PAD2 setting
the board type.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This ensures the index is 0 on FW recovery and prevents spurious error
prints - "WARNING illegal id in tx completion".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only wl127x chips use the rx_mem_pool_addr values, which need to be
given to the firmware as part of the RX path. Move this from core to
the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Read the HW PG version of the 18xx chip from FUSE.
Based on an earlier patch by Luciano Coelho <coelho@ti.com>.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only wl12xx needs to get the ref_clock anc tcxo_clock values from the
platform data. Move these elements from the wl1271 structure to
wl12xx's private data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl12xx.h file now contains mostly definitions that are internal to
wlcore. Still, some things need to me moved to the public header, so
for now we keep including it in wlcore.h.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Instead of using hardcoded values for a single frequency, we need to
read the frequency and use the appropriate values for it in the top
initialization.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define the FW pc in the 18xx register translation table. This specific
register is only valid in the boot partition, so change the momentarily
change partitions. This doesn't damage 12xx cards, where the FW pc is
accessible via boot partition as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware uses the SCR_PAD2 register to read the board type passed
from the driver. The values don't match the ones used in the mac and
phy configuration, so we need to map them before writing. This commit
adds a translation table that is used when writing the board type to
SCR_PAD2.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Different board types (ie. FPGA, HDK and DVP/EVB) require slightly
different init configuration options. Since we cannot probe the type
of board from the actual hardware, we need to pass it as an option
during module load.
This patch adds a module parameters that accepts the 3 different board
types, with DVP/EVB as the default, and uses this value where needed.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Set an alternate HT cap allowing MIMO rates (but only 20mhz) channels,
when the module is loaded with ht_mode=mimo.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Define the default HT capabilities of the 18xx chip family - these include
support for wide-channel.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add a HW op to add extra enabled rates for AP-mode data-rates. Since
the rates might depend on channel properties, reconfigure AP-mode rates
when these change.
Implement the HW op for the 18xx family, where MIMO or wide-chan rates
can be added.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Parse the peer ht_cap element containing MCS8-MCS15 rates and pass it
to the FW. Rates unsupported by the HW will be sanitized by mac80211
before reaching us.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Translate the NL80211 channel type to a FW-specific channel type and send
it to the FW as part of the role-start command. For wl12xx this has no
effect - this element is treated as padding.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Track the current 802.11 channel type, defaulting to a NO_HT channel.
Update the channel type element when changed by mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Now wlcore requires the lower drivers to set the correct
configuration. Move the existing private configuration to the proper
place and add all generic configuration parameters.
The important changes are in Tx interrupt pacing and Rx BA window size.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Some chip families can checksum certain classes of Rx packets in FW.
Implement the Rx-checksum feature as a HW-op. For the 18xx chip-family,
set Rx-checsum according to indication from FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some chip families are capable of checksumming certain classes of Tx
packets in HW. Indicate this fact in the netdev features and perform the
HW checksum by protocol type for the 18xx family.
Fix the location of the skb network header when we move it so we can
rely on it when setting the checksum.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement immediate Tx completion for the 18xx family. Move 18xx
specific Tx code to new tx.c/h files and create helper header files
for definitions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the 18xx-specific way for getting the length of a Rx packet.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the HW op for getting alignment state in wl18xx. The FW aligns
the Rx Ethernet payload data.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl18xx chip passes extra information in the firmware status to the
driver. Add a private data section to handle that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define HW-rate conversion tables for the 18xx chip. Initialize
the appropriate wlcore elements with these tables and values to allow
conversion of HW-rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the frame length during Tx in a way compatible with the 18xx FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the 18xx variant to the HW Tx descriptor union and set the 18xx
specific values during Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the Tx spare block counts for all operating modes in the 18xx
card.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the number of Tx-descriptors for the 18xx family.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make use of the wlcore provided private storage in the 18xx low-level
driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the operations that allow wlcore to trigger commands to the
firmware and acknowledge when an event has been fully received.
Allocate a private buffer to hold the maximum sized cmd. Send the
entire length of the buffer each time a command is sent to signal
EOT. Remove the previous EOT mechanism.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the boot operation. Add a wl18xx-specific configuration
structure (namely to configure the mac and phy parameters).
The default hw configuration matches the DVP board.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add identify_chip operation to detect the chip ID for wl185x and set
the correct firmware name.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the register table with the appropriate values for wl18xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We don't have any chip-specific operations yet, but now wlcore has
defined an operations structure and requires the pointer to be set.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
At least in PG1, the wl18xx chips use the same SDIO vendor/device ID,
so it's not possible to figure out which driver is to be used. As a
workaround, we can check the SDIO revision number, because wl18xx uses
3.00 and wl12xx does not.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the wl18xx module and the probe functions. Use wlcore for the
main parts (not functional at this point due to differences in the
wl18xx initialization).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In probe(), rdev->regmap must be assigned.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Locking mutex in different orders just screams for
deadlocks, and some testing showed that it is actually
quite easy to trigger them.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Properly set up the RBs
- Properly set up the SPI
- Properly set up gb_addr_config
This should fix rendering issues on certain cards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many TVs and A/V receivers don't work with this bit set. Problem was
confirmed using: Onkyo TX-SR605, Sony BRAVIA KDL-52X3500, Sony BRAVIA
KDL-40S40xx. In theory this bit shouldn't affect audio engine when
feeding it with data, however it seems it does. Driver fglrx doesn't set
that bit in any of the above cases.
This fixes a regression introduced by 3.5-rc1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is based on info released by AMD, should allow using audio in much
more cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call it in the asic startup callback on all asics.
Previously r600 and rv770 called it in the startup
and resume callbacks while all the other asics called
it in the startup callback.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Blending for graphic layer 0 of hdmi mixer was not set so video
layer cannot be showed if graphic layer 0 is enabled.
This patch fixes blending values to support blending between
graphic layer 0 and video layer.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The encoder get_crtc operation is called to retrieve a pointer to the
CRTC the encoder is currenctly connected to, right after setting the
encoder::crtc field to the new CRTC. The implementation of this
operation returns the pointer to the new CRTC, which is then pointlessly
compared to itself.
As the operation is not mandatory, don't implement it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
GEM objects used by frame buffers must be referenced for the whole life
of the frame buffer. Release the references in the frame buffer
destructor instead of its constructor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The exynos_drm_gem_dumb_map_offset() doesn't need to access any
Exynos-specific GEM object fields, don't cast the GEM object.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
DRIVER_BUS_PLATFORM is a bus type used internally in the DRM core, not a
flag for the drm_driver::driver_features field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The NV12M/YUV420M formats are identical to the already existing standard
NV12/YUV420 formats. The M variants will be removed, so convert the
driver to use the standard names.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
When receiving a DEP link down event, we should cancel all pending URBs
if we're activated as a target or if we're an initiator.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When trying to enable a DEP link as a passive initiator, pn533 needs to
provide the polling request command payload.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This one needs to be called as soon as we are activated as a target, for
the pn533 to receive the first SYMM and keep the LLCP link alive.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Userspace gets a netlink event upon target mode activation.
The LLCP layer is also signaled when we get an ATR_REQ in order to get
the remote general bytes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some environments, dramatic performance savings may be obtained because
swapped pages are saved in RAM (or a RAM-like device) instead of a swap disk.
This tag provides the basic infrastructure along with some changes to the
existing backends.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJPsorBAAoJEFjIrFwIi8fJcz8H/RBXCtFo0kiJmRked3nMAIDO
/2zN/q/Qawsg9aeoGlP7G8hQi9PMipbhQj3ixHyCTMv0zMbH988GXbBce+gIcg6e
TOQi7xXAuPEwLizmSpiTv84XzN5bMgu1oJXEqIXw0EIpuZAmp+9m/o3WBwEAtyxi
B+hvjE7eZM8f75K3lxs6sOtmIcERj9zqmT933Y8+i9iiuRyGMey2SyKtvVLbYZ+j
HroFMUi0so5TzxT/cpkRiHu0U75c651o+LV00zh7InMqbwyRsWlKTf53k8Q/q2WP
I7dVmfItwN/TpOrYTfxglYFlbYuUP35ziFvZ2trd6hcs9RK8OuKw+OmBLReHTtc=
=x9Vp
-----END PGP SIGNATURE-----
Merge tag 'stable/frontswap.v16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull frontswap feature from Konrad Rzeszutek Wilk:
"Frontswap provides a "transcendent memory" interface for swap pages.
In some environments, dramatic performance savings may be obtained
because swapped pages are saved in RAM (or a RAM-like device) instead
of a swap disk. This tag provides the basic infrastructure along with
some changes to the existing backends."
Fix up trivial conflict in mm/Makefile due to removal of swap token code
changing a line next to the new frontswap entry.
This pull request came in before the merge window even opened, it got
delayed to after the merge window by me just wanting to make sure it had
actual users. Apparently IBM is using this on their embedded side, and
Jan Beulich says that it's already made available for SLES and OpenSUSE
users.
Also acked by Rik van Riel, and Konrad points to other people liking it
too. So in it goes.
By Dan Magenheimer (4) and Konrad Rzeszutek Wilk (2)
via Konrad Rzeszutek Wilk
* tag 'stable/frontswap.v16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
frontswap: s/put_page/store/g s/get_page/load
MAINTAINER: Add myself for the frontswap API
mm: frontswap: config and doc files
mm: frontswap: core frontswap functionality
mm: frontswap: core swap subsystem hooks and headers
mm: frontswap: add frontswap header file
If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.
Cc: stable@kernel.org
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.
BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since my commit
iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.
Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull timer updates from Thomas Gleixner:
"The clocksource driver is pure hardware enablement and the skew option
is default off, well tested and non dangerous."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move skew_tick option into the HIGH_RES_TIMER section
clocksource: em_sti: Add DT support
clocksource: em_sti: Emma Mobile STI driver
clockevents: Make clockevents_config() a global symbol
tick: Add tick skew boot option
Empirical evidence suggests that we need to: On at least one ivb
machine when running the hangman i-g-t test, the rings don't properly
initialize properly - the RING_START registers seems to be stuck at
all zeros.
Holding forcewake around this register init sequences makes chip reset
reliable again. Note that this is not the first such issue:
commit f01db988ef
Author: Sean Paul <seanpaul@chromium.org>
Date: Fri Mar 16 12:43:22 2012 -0400
drm/i915: Add wait_for in init_ring_common
added delay loops to make RING_START and RING_CTL initialization
reliable on the blt ring at boot-up. So I guess it won't hurt if we do
this unconditionally for all force_wake needing gpus.
To avoid copy&pasting of the HAS_FORCE_WAKE check I've added a new
intel_info bit for that.
v2: Fixup missing commas in static struct and properly handling the
error case in init_ring_common, both noticed by Jani Nikula.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By correctly describing the rinbuffers as being in the GTT domain, it
appears that we are more careful with the management of the CPU cache
upon resume and so prevent some coherency issue when submitting commands
to the GPU later. A secondary effect is that the debug logs are then
consistent with the actual usage (i.e. they no longer describe the
ringbuffers as being in the CPU write domain when we are accessing them
through an wc iomapping.)
Reported-and-tested-by: Daniel Gnoutcheff <daniel@gnoutcheff.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41092
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch removes two useless initialisations in the
stmmac_rx and stmmac_tx functions.
In the former, the count variable was reset twice and in
the stmmac_tx we only need to increment the dirty pointer
w/o setting the entry variable.
v2: review the subject and comment that was not clear in my
first version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the busy-waiting/udelay to wait_event on outstanding sends.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is useful for SoCs whose I2C module's signals can be routed to
different sets of pins at run-time, using the pinctrl API.
+-----+ +-----+
| dev | | dev |
+------------------------+ +-----+ +-----+
| SoC | | |
| /----|------+--------+
| +---+ +------+ | child bus A, on first set of pins
| |I2C|---|Pinmux| |
| +---+ +------+ | child bus B, on second set of pins
| \----|------+--------+--------+
| | | | |
+------------------------+ +-----+ +-----+ +-----+
| dev | | dev | | dev |
+-----+ +-----+ +-----+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In the error path of the ppr_notifer it can happen that the
iommu->lock is taken recursivly. This patch fixes the
problem by releasing the iommu->lock before any notifier is
invoked. This also requires to move the erratum workaround
for the ppr-log (interrupt may be faster than data in the log)
one function up.
Cc: stable@vger.kernel.org # v3.3, v3.4
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
At some point pci_get_bus_and_slot started to enable
interrupts. Since this function is used in the
amd_iommu_resume path it will enable interrupts on resume
which causes a warning. The fix will use a cached pointer
to the root-bridge to re-enable the IOMMU in case the BIOS
is broken.
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
In function dsi_compute_interleave_lp(), the escape clock/LP clock time period
is calculated incorrectly. The escape clock/LP clock is calculated as:
LP Clock(Hz) = DSI_FCLK(Hz) / lp_clk_div
Since we are calculating the time period of LP clock, the LP clock divider
should be multiplied with the time period of DSI_FCLK.
Calculating incorrect value of txclkesc results in incorrect calculation of LP
interleaving parameters, it also creates a possibility of a divide by zero
error.
Reported-by: Sureshkumar Manimuthu <mail2msuresh@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 4dbd8f63f0 (regulator: gpio-regulator: Set the smallest
voltage/current in the specified range) forgot to set the newly
introduced best_val.
Therefore it stayed always at INT_MAX thus breaking the setting
of the voltage.
Included is also an init value for target, as warnings about
a possibly uninitialised target started appearing with this fix.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit c172708d38 (regulator: core: Use a struct to pass in
regulator runtime configuration) added the drvdata pointer
only per reference to the new config array in the gpio-regulator.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
__devexit functions are discarded when CONFIG_HOTPLUG
is not set, so the symbol needs to be referenced carefully.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The devm_kzalloc function eliminates the need for manual resource releasing
and simplify error handling. Resources allocated by devm_* are freed
automatically on driver detach.
Thus adding kfree calls here will introduce double free bug.
The memory of desc array and the pointers to the rdev[] are allocated by
devm_kzalloc call for struct palmas_pmic.
struct palmas_pmic {
struct palmas *palmas;
struct device *dev;
struct regulator_desc desc[PALMAS_NUM_REGS];
struct regulator_dev *rdev[PALMAS_NUM_REGS];
struct mutex mutex;
int smps123;
int smps457;
int range[PALMAS_REG_SMPS10];
};
Which means we should not call kfree for pmic->rdev and pmic->desc.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pm_runtime_put_sync() in dss_runtime_put() returns -EBUSY when any child
of dss is still enabled. This happens, for example, when a display
output is enabled and one dumps the clocks via debugfs. This causes
dss_runtime_get & put to be called.
While I couldn't find anything about this in the documentation and it
wasn't immediately clear from runtime_pm code, it looks to me that
pm_runtime_put_sync() returns -EBUSY to inform that things went fine,
but the device could not be turned off as there are still child devices
that are enabled. This is not a problem.
This patch skips the WARN_ON if pm_runtime_put_sync() returns -EBUSY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes a warning:
drivers/video/omap2/displays/panel-taal.c: In function
‘taal_num_errors_show’:
drivers/video/omap2/displays/panel-taal.c:529: warning: ‘errors’ may be
used uninitialized in this function
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If CONFIG_DEBUG_FS or CONFIG_OMAP2_DSS_DEBUG_SUPPORT is disabled, the
build fails:
drivers/video/omap2/dss/core.c:197:50: error: static declaration of
'dss_debugfs_create_file' follows non-static declaration
drivers/video/omap2/dss/dss.h:166:5: note: previous declaration of
'dss_debugfs_create_file' was here
This patch fixes the dummy dss_debugfs_create_file() so that the driver
builds.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The way the for_each_maps() macro is currently used, using "i" instead of
"_i_" works and is harmless. Still, this is a bug, that can trigger any
time, if the code around that macro changes. Better fix it now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit e605b743f3 ("IB/mlx4: Increase the number of vectors (EQs)
available for ULPs") didn't handle correctly the case where there
aren't enough MSI-X vectors to increase the number of EQs, so only the
legacy EQs are allocated. This results in an attempt to memset() to
zero the EQ table which was never allocated and a kernel crash.
Fix this by checking in the teardown flow if the table of EQs was ever
allocated. Also remove some unneeded setting to zero of the EQ
related fields in struct mlx4_ib_dev.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When using rping -c -a 0.0.0.0 with iw_cxgb4, the system crashes when
rdma_connect() is called. ip_dev_find() will return NULL, but pdev is
accessed anyway.
Checking that pdev is NULL and returning -ENODEV prevents the system
from crashing.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update bugfix-video branch to 2.5-rc1
so I don't have to again resolve the
conflict in these patches vs. upstream.
Conflicts:
drivers/gpu/drm/gma500/psb_drv.c
text conflict: add comment vs delete neighboring line
keep just this:
/* igd_opregion_init(&dev_priv->opregion_dev); */
/* acpi_video_register(); */
Signed-off-by: Len Brown <len.brown@intel.com>
Should be 'exynos5_xxx' instead of 'exonys5_xxx'.
It happened at the commit 30b842889e ("Merge tag 'soc2' of
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc")
during v3.5 merge window.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ My bad - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following build warning:
warning: (ACPI_HOTPLUG_CPU) selects ACPI_CONTAINER which has unmet direct dependencies (ACPI && EXPERIMENTAL)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull some left-over PM patches from Rafael J. Wysocki.
* 'pm-acpi' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Make acpi_pm_device_sleep_state() follow the specification
ACPI / PM: Make __acpi_bus_get_power() cover D3cold correctly
ACPI / PM: Fix error messages in drivers/acpi/bus.c
rtc-cmos / PM: report wakeup event on ACPI RTC alarm
ACPI / PM: Generate wakeup events on fixed power button
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The word to be transmitted/received via regmap is composed by the following
parts:
config->reg_bits
config->val_bits
config->pad_bits
,so the total size should be calculated by summing up the number of bits of
each element and using a DIV_ROUND_UP to return the number of bytes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If debugfs isn't cleaned up, stale files will be left in the filesystem
which will cause an OOPS when accessed the first time, and hang the
accessing application when accessed again, presumably due to some lock
being left held.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to use O_DSYNC for all cases at FILEIO backend creation time to
avoid the extra syncing of pure timestamp updates with legacy O_SYNC during
default operation as recommended by hch. Continue to do this independently of
Write Cache Enable (WCE) bit, as WCE=0 is currently the default for all backend
devices and enabled by user on per device basis via attrib/emulate_write_cache.
This patch drops the now unnecessary fd_buffered_io= token usage that was
originally signalling when to explictly disable O_SYNC at backend creation
time for buffered I/O operation. This can end up being dangerous for a number
of reasons during physical node failure, so go ahead and drop this option
for now when O_DSYNC is used as the default.
Also allow explict FUA WRITEs -> vfs_fsync_range() call to function in
fd_execute_cmd() independently of WCE bit setting.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wCpY
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb
ii) Migration of thin devices from one pool to another.
iii) Merging snapshots back into an external origin.
iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull networking updates from David Miller:
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
