Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEs "output" can sometimes combine IEs coming from userspace
with IEs generated in the kernel - in particular mac80211 does
this for association frames.
Add support in this code for the 802.11 IE fragmentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure if an AP (and associated VLANs) will
do multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own MAC
address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[fix disabling, add better documentation & commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new nl80211 attributes can be used to provide KEK and nonces to
allow the driver to encrypt and decrypt FILS (Re)Association
Request/Response frames in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This defines authentication algorithms for FILS (IEEE 802.11ai).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we split the wiphy dump because it got too large, I added a
comment and asked that all new command advertising be done only
for userspace clients capable of receiving split data, in order
to not break older ones (which can't use the new commands anyway)
This mostly worked, and we haven't added many new commands, but
I occasionally get patches that modify the wrong place.
Make this easier to detect and understand by splitting out the
old commands to a separate function that makes it more clear it
should never be modified again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the pointless checking against interface combinations in
the initial basic beacon interval validation, that currently isn't
taking into account radar detection or channels properly. Instead,
just validate the basic range there, and then delay real checking
to the interface combination validation that drivers must do.
This means that drivers wanting to use the beacon_int_min_gcd will
now have to pass the new_beacon_int when validating the AP/mesh
start.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can't really be supported right now, because the IBSS
interface may change its beacon interval at any time due to
joining another network; thus, there's already "support"
for different beacon intervals here, implicitly.
Until we figure out how we should handle this case (continue
to allow it to arbitrarily join? Join only if compatible?)
disallow advertising that different beacon intervals are
supported if IBSS is allowed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is needed for beacon interval validation; if we don't
store it, then new interfaces added won't validate that the
beacon interval is the same as existing ones. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We shouldn't abort the iteration with an error when one of the
potential combinations can't accomodate the beacon interval
request, we should just skip that particular combination. Fix
the code to do so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a helper using wdev to check if interface is running. This
deals with both non-netdev and netdev interfaces. In struct
wireless_dev replace 'p2p_started' and 'nan_started' by
'is_running' as those are mutually exclusive anyway, and unify
all the code to use wdev_running().
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The old WDS 4-addr frame support is very limited, e.g.
* no encryption is possible on such links
* it cannot support rate/HT/VHT negotiation
* management APIs are very restricted
These make the WDS legacy mode useless in practice.
All of these are resolved by the 4-addr AP/client support,
so there's also no reason to improve WDS in the future.
Therefore, add a Kconfig option to disable legacy WDS.
This gives people an "emergency valve" while they migrate
to the better-supported 4-addr AP/client option; we plan
to remove it (and the associated cfg80211/mac80211 code,
which is the ultimate goal) in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When suspending without WoWLAN, cfg80211 will ask drivers to
disconnect. Even when the driver does this synchronously, and
immediately returns with a notification, cfg80211 schedules
the handling thereof to a workqueue, and may then call back
into the driver when the driver was already suspended/ing.
Fix this by processing all events caused by cfg80211_leave_all()
directly after that function returns. The driver still needs to
do the right thing here and wait for the firmware response, but
that is - at least - true for mwifiex where this occurred.
Reported-by: Amitkumar Karwar <akarwar@marvell.com>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow vendor commands that require WIPHY_VENDOR_CMD_NEED_RUNNING flag
to be sent to NAN interface.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On a disconnect request from userspace, cfg80211 currently calls
called rdev_disconnect() only in case that 'current_bss' was set,
i.e. connection had been established.
Change this to allow the userspace call to succeed and call the
driver's disconnect() method also while the connection attempt is
in progress, to be able to abort attempts.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[change commit subject/message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'limits' is malloced in cfg80211_iter_combinations() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To avoid unused variable warnings when CONFIG_PM isn't set,
add the appropriate ifdef to the policies that are only used
for WoWLAN, which can only be invoked when CONFIG_PM is set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was clearly intended to be used in the attribute parsing,
so do that instead of leaving the attribute policy unused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit provides a mechanism for the host drivers to advertise the
support for different beacon intervals among the respective interface
combinations in a group, through NL80211_IFACE_COMB_BI_MIN_GCD (u32).
This value will be compared against GCD of all beaconing interfaces of
matching combinations.
If the driver doesn't advertise this value, the old behaviour where
all beacon intervals must be identical is retained.
If it is specified, then any beacon interval for an interface in the
interface combination as well as the GCD of all active beacon intervals
in the combination must be greater or equal to this value.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[change commit message, some variable names, small other things]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the growing parameter list to a structure for the interface
combination check and iteration functions in cfg80211 and mac80211
to make the code easier to understand.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not accept arbitrary DA/SA inside A-MSDUs, it could be used
to circumvent protections, like allowing a station to send frames and
make them seem to come from somewhere else.
Add the necessary infrastructure in cfg80211 to allow such checks, in
further patches we'll start using them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single case where has_80211_header is passed as true,
which is in mac80211. Given that there's only simple code that needs
to be done before calling it, export that function from cfg80211
instead and let mac80211 call it itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide a function that reports NAN DE function termination. The function
may be terminated due to one of the following reasons: user request,
ttl expiration or failure.
If the NAN instance is tied to the owner, the notification will be
sent to the socket that started the NAN interface only
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide a function the driver can call to report a match.
This will send the event to the user space.
If the NAN instance is tied to the owner, the notifications will be
sent to the socket that started the NAN interface only.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NAN configuration paramaters may change during the operation of
the NAN device. For example, a user may want to update master preference
value when the device gets plugged/unplugged to the power.
Add API that allows to do so.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A NAN function can be either publish, subscribe or follow
up. Make all the necessary verifications and just pass the
request to the driver.
Allow the user space application that starts NAN to
forbid any other socket to add or remove functions.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers that implement static WEP internally, i.e.
expose connection keys to the driver in connect flow and don't
upload the keys after the connection.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reported that during (repeated) wext_pmf test runs (from the
wpa_supplicant hwsim test suite) the kernel crashes. The reason is
that after the key is set, the wext code still unnecessarily stores
it into the key cache. Despite smatch pointing out an overflow, I
failed to identify the possibility for this in the code and missed
it during development of the earlier patch series.
In order to fix this, simply check that we never store anything but
WEP keys into the cache, adding a comment as to why that's enough.
Also, since the cache is still allocated early even if it won't be
used in many cases, add a comment explaining why - otherwise we'd
have to roll back key settings to the driver in case of allocation
failures, which is far more difficult.
Fixes: 89b706fb28 ("cfg80211: reduce connect key caching struct size")
Reported-by: Jouni Malinen <j@w1.fi>
Bisected-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous commit added support for specifying the beacon rate
for AP mode. Add features checks to this, and extend it to also
support the rate configuration for mesh networks. For IBSS it's
not as simple due to joining etc., so that's not yet supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows an option to configure a single beacon tx rate for an AP.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=s1MY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have various things - all across the board:
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few places where an IE that matches not only the EID, but
also other bytes inside the element, needs to be found. To simplify
that and reduce the amount of similar code, implement a new helper
function to match the EID and an extra array of bytes.
Additionally, simplify cfg80211_find_vendor_ie() by using the new
match function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For an array, there's no need to use &array, so just use the
plain wiphy->addresses[i].addr here to silence smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few instances were found where we didn't check them, add the
missing checks even though they'll probably never trigger as
the message should be large enough here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the message got full during nla_nest_start(), it can return
NULL. None of the cases here seem like that can really happen,
but check the return value nonetheless.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no point in allowing connect keys when one of them
isn't also configured as the TX key, it would just confuse
drivers and probably cause them to pick something for TX.
Disallow this confusing and erroneous configuration.
As wpa_supplicant will always send NL80211_ATTR_KEYS, even
when there are no keys inside, allow that and treat it as
though the attribute isn't present at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the previous patches, connect keys can only (correctly)
be used for storing static WEP keys. Therefore, remove all the
data for dealing with key index 4/5 and reduce the size of the
key material to the maximum for WEP keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't accept it if a key_idx < 0 snuck through, reject WEP keys with
key index 4 and 5 (which are used for IGTKs) and don't allow IGTKs
with key indices other than 4 and 5. This makes the key data match
expectations better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When not connected, anything but WEP keys shouldn't be allowed to be
configured for later - only static WEP keys make sense at this point.
Change wext to reject anything else just like nl80211 does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was already documented that way in nl80211.h, but the
parsing code still accepted other key types. Change it to
really only accept WEP keys as documented.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only key index 0-3 should be accepted, 4/5 are for IGTKs and
cannot be used as connect keys. Fix the range checking to not
allow such erroneous configurations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Key index 4 can only be used for an IGTK, so the range checks
for shared key authentication should treat 4 as an error, fix
that in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Cc: stable@vger.kernel.org
Fixes: 9a774c78e2 ("cfg80211: Support multiple CSA counters")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "cfg80211_wq" is involved in cleanup, scan and event related
works. It queues multiple work items &rdev->event_work,
&rdev->dfs_update_channels_wk,
&wiphy_to_rdev(request->wiphy)->scan_done_wk,
&wiphy_to_rdev(wiphy)->sched_scan_results_wk, which require strict
execution ordering.
Hence, an ordered dedicated workqueue has been used.
Since it's a wireless driver, WQ_MEM_RECLAIM has been set to ensure
forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows GET_INTERFACE dumps to be filtered based on
NL80211_ATTR_WIPHY or NL80211_ATTR_WDEV. The documentation for
GET_INTERFACE mentions that this is possible:
"Request an interface's configuration; either a dump request on
a %NL80211_ATTR_WIPHY or ..."
However, this behavior has not been implemented until now.
Johannes: rewrite most of the patch:
* use nl80211_dump_wiphy_parse() to also allow passing an interface
to be able to dump its siblings
* fix locking (must hold rtnl around using nl80211_fam.attrbuf)
* make init self-contained instead of relying on other cb->args
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* revert a recent wext patch, which Ben Hutchings noticed was
wrong, and it turns out not to be necessary for any driver
* fix an infinite loop that can occur under certain conditions
in mac80211's TDLS code (depending on regulatory information)
* add a cfg80211_get_station() static inline when cfg80211 isn't
built, to allow other modules to not have to depend on it for it
-----BEGIN PGP SIGNATURE-----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=dFzv
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three little fixes:
* revert a recent wext patch, which Ben Hutchings noticed was
wrong, and it turns out not to be necessary for any driver
* fix an infinite loop that can occur under certain conditions
in mac80211's TDLS code (depending on regulatory information)
* add a cfg80211_get_station() static inline when cfg80211 isn't
built, to allow other modules to not have to depend on it for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
Different gcc versions appear to be treating enum with different
signedness, causing warnings with the out parameter one way or
the other.
Just use the correct type to avoid all that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon interval interface combinations validation was missing
for MESH/IBSS join, add those.
Johannes: also move the beacon interval check disallowing really
tiny and really big intervals into the common function, which
adds it for AP mode.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change alters the semantics of NL80211_CMD_DEL_INTERFACE events
by always sending this event whenever a net_device object associated
with a wdev is destroyed. Prior to this change, this event was only
emitted as a result of NL80211_CMD_DEL_INTERFACE command sent from
userspace. This allows userspace to reliably detect when wireless
interfaces have been removed, e.g. due to USB removal events, etc.
For wireless device objects without an associated net_device (e.g.
NL80211_IFTYPE_P2P_DEVICE), the NL80211_CMD_DEL_INTERFACE event is
now generated inside cfg80211_unregister_wdev.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change alters the semantics of NL80211_CMD_NEW_INTERFACE events
by always sending this event whenever a new net_device object
associated with a wdev is registered. Prior to this change, this event
was only sent as a result of NL80211_CMD_NEW_INTERFACE command sent
from userspace. This allows userspace to reliably detect new wireless
interfaces (e.g. due to hardware hot-plug events, etc).
For wdevs created without an associated net_device object (e.g.
NL80211_IFTYPE_P2P_DEVICE), the NL80211_CMD_NEW_INTERFACE event is
still generated inside the relevant nl80211 command handler.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 3d5fdff46c.
Ben Hutchings pointed out that the commit isn't safe since it assumes
that the structure used by the driver is iw_point, when in fact there's
no way to know about that.
Fortunately, the only driver in the tree that ever runs this code path
is the wilc1000 staging driver, so it doesn't really matter.
Clearly I should have investigated this better before applying, sorry.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [though I guess it doesn't matter much]
Fixes: 3d5fdff46c ("wext: Fix 32 bit iwpriv compatibility issue with 64 bit Kernel")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, NL80211_MESHCONF_HT_OPMODE validation rejected correct
flag combinations, e.g. IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED |
IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT.
Doing just a range-check allows setting flags that don't exist (0x8)
and invalid flag combinations.
Implements some checks based on IEEE 802.11 2012 8.4.2.59 "HT
Operation element".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword commit message, simplify a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch on chandef->width is missing a break on the
NL8211_CHAN_WIDTH_80P80 case; currently we get a WARN_ON when
center_freq2 is non-zero because of the missing break.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add API to support VHT MU-MIMO air sniffer.
in MU-MIMO there are parallel frames on the air while the HW
has only one RX.
add the capability to sniff one of the MU-MIMO parallel frames by
giving the sniffer additional information so it'll know which
of the parallel frames it shall follow.
Add attribute - NL80211_ATTR_MU_MIMO_GROUP_DATA - for getting
a MU-MIMO groupID in order to monitor packets from that group
using VHT MU-MIMO.
And add attribute -NL80211_ATTR_MU_MIMO_FOLLOW_ADDR - for passing
MAC address to monitor mode.
that option will be used by VHT MU-MIMO air sniffer to follow a
station according to it's MAC address using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No support for pbss results in a memory leak for the acl_data
(if parse_acl_data succeeds). Fix this by moving the ACL parsing later.
Cc: stable@vger.kernel.org
Fixes: 34d505193b ("cfg80211: basic support for PBSS network type")
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
When building a kernel with W=1, the nl80211.c file causes a number of
warnings, all about the same problem:
net/wireless/nl80211.c: In function 'nl80211_parse_mesh_config':
net/wireless/nl80211.c:5287:103: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5290:96: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5293:124: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5295:148: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5298:106: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5305:116: error: comparison is always false due to limited range of data type [-Werror=type-limits]
The problem is that gcc does not notice that the check is generate
by a macro, so it complains about comparing an unsigned type against 0.
I've tried to come up with a way to rephrase that code in a way that
avoids the warnings and otherwise improves the code as well.
This uses a set of new helper functions that perform the range checking,
and should provide slightly better type safety than the older patch,
at the expense of adding 44 lines to the code. Binary code size is
basically unchanged though (20 bytes added to 126561 bytes .text).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes: 2d1c304cb2 ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
-----BEGIN PGP SIGNATURE-----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=FvhQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting rd to NULL to avoid freeing it, just to be able to return
from the function in a single place, doesn't make much sense.
Return the set_regdom() return value directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the following checkpatch.pl issues -
- Please don't use multiple blank lines
- Blank lines aren't necessary before a close brace
- Missing a blank line after declarations
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kirtika Ruchandani <kirtika.ruchandani@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwpriv app uses iw_point structure to send data to Kernel. The iw_point
structure holds a pointer. For compatibility Kernel converts the pointer
as required for WEXT IOCTLs (SIOCIWFIRST to SIOCIWLAST). Some drivers
may use iw_handler_def.private_args to populate iwpriv commands instead
of iw_handler_def.private. For those case, the IOCTLs from
SIOCIWFIRSTPRIV to SIOCIWLASTPRIV will follow the path ndo_do_ioctl().
Accordingly when the filled up iw_point structure comes from 32 bit
iwpriv to 64 bit Kernel, Kernel will not convert the pointer and sends
it to driver. So, the driver may get the invalid data.
The pointer conversion for the IOCTLs (SIOCIWFIRSTPRIV to
SIOCIWLASTPRIV), which follow the path ndo_do_ioctl(), is mandatory.
This patch adds pointer conversion from 32 bit to 64 bit and vice versa,
if the ioctl comes from 32 bit iwpriv to 64 bit Kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Tested-by: Dibyajyoti Ghosh <dibyajyotig@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since set_tx_power and set_antenna are frequently implemented
without the matching get_tx_power/get_antenna, we shouldn't
have added warnings for those. Remove them.
The remaining ones are correct and need to be implemented
symmetrically for correct operation.
Cc: stable@vger.kernel.org
Fixes: de3bb771f4 ("cfg80211: add more warnings for inconsistent ops")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver extended capabilities may differ for different
interface types which the userspace needs to know (for
example the fine timing measurement initiator and responder
bits might differ for a station and AP). Add a new nl80211
attribute to provide extended capabilities per interface type
to userspace.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the status parameter to cfg80211_connect_result() was
documented as using WLAN_STATUS_UNSPECIFIED_FAILURE (1) when the real
status code for the failure is not known. This value can be used by an
AP (and often is) and as such, user space cannot distinguish between
explicitly rejected authentication/association and not being able to
even try to associate or not receiving a response from the AP.
Add a new inline function, cfg80211_connect_timeout(), to be used when
the driver knows that the connection attempt failed due to a reason
where connection could not be attempt or no response was received from
the AP. The internal functions now allow a negative status value (-1) to
be used as an indication of this special case. This results in the
NL80211_ATTR_TIMED_OUT to be added to the NL80211_CMD_CONNECT event to
allow user space to determine this case was hit. For backwards
compatibility, NL80211_STATUS_CODE with the value
WLAN_STATUS_UNSPECIFIED_FAILURE is still indicated in the event in such
a case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[johannes: fix cfg80211_connect_bss() prototype to use int for status,
add cfg80211_connect_timeout() to docbook, fix docbook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While a wiphy can be transferred to network namespaces, a process having
CAP_NET_ADMIN in a non-initial user namespace can not administrate such
devices due to the genetlink GENL_ADMIN_PERM restrictions.
For openvswitch having the same issue, a new GENL_UNS_ADMIN_PERM flag has
been introduced, commit 4a92602aa1 ("openvswitch: allow management from
inside user namespaces"). This patch changes all privileged operations
operating on a wiphy, dev or wdev to allow their administration using the
same mechanism. All operations use either NEED_WIPHY, NEED_WDEV or
NEED_NETDEV, which implies a namespace aware lookup of the device. The only
exception is NL80211_CMD_SET_WIPHY, which explicitly uses a namespace aware
phy lookup.
Signed-off-by: Martin Willi <martin@strongswan.org>
[also allow cancel scan, for completeness]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The devlist_mtx mutex was removed about two years ago, in favour of just
using RTNL/RCU protection. Remove the comment still referencing it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows finding vendor IE from a specific vendor.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since a/b/g/n no longer exist as spec amendements and VHT (ex 802.11ac)
wasn't handled at all, it's better to just remove the amendment strings
to avoid confusion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nicolas converted most users, but didn't realize some were generated
by macros. Convert those over as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 maintains separate BSS table entries for APs if the same
BSSID, SSID pair is seen on multiple channels, it is possible that it
can map the current_bss to a BSS entry on the wrong channel. This
current_bss will not get flushed unless disconnected and cfg80211
reports a wrong channel as the associated channel.
Fix this by introducing a new cfg80211_connect_bss() function which is
similar to cfg80211_connect_result(), but it includes an additional
parameter: the bss the STA is connected to. This allows drivers to
provide the exact bss entry that matches the BSS to which the connection
was completed.
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the a station statistics netlink attribute:
NL80211_STA_INFO_RX_DURATION.
If present, this attribute contains the aggregate PPDU duration (in
microseconds) for all the frames from the peer. This is useful to
help understand the total time spent transmitting to us by all of
the connected peers.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.
Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.
Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.
Fixes: 026331c4d9 ("cfg80211/mac80211: allow registering for and sending action frames")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user space issues a NL80211_CMD_CONNECT with
NL80211_ATTR_PREV_BSSID when there is already a connection, allow this
to proceed as a reassociation instead of rejecting the new connect
command with EALREADY.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[validate prev_bssid]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_CONNECT to allow the NL80211_ATTR_PREV_BSSID
attribute to be used similarly to way this was already allowed with
NL80211_CMD_ASSOCIATE. This allows user space to request reassociation
(instead of association) when already connected to an AP. This provides
an option to reassociate within an ESS without having to disconnect and
associate with the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanisms, and thus
if a P2P GO has a legacy client connected to it, it has to make
some changes in the PS behavior.
To handle this, add an attribute to specify whether a station supports
P2P PS or not. If the attribute was not specified cfg80211 will assume
that station supports it for P2P GO interface, and does NOT support it
for AP interface, matching the current assumptions in the code.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introducing a new feature that the driver can use to
indicate the driver/firmware supports configuration of BSS
selection criteria upon CONNECT command. This can be useful
when multiple BSS-es are found belonging to the same ESS,
ie. Infra-BSS with same SSID. The criteria can then be used to
offload selection of a preferred BSS.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[move wiphy support check into parse_bss_select()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows scans for a specific BSSID to be optimized by the user space
application by requesting the driver to set the Probe Request frame
BSSID field (Address 3) to the specified BSSID instead of the wildcard
BSSID. This prevents other APs from replying which reduces airtime need
and latency in getting the response from the target AP through.
This is an optimization and as such, it is acceptable for some of the
drivers not to support the mechanism. If not supported, the wildcard
BSSID will be used and more responses may be received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If register_netdevice_notifier() fails (which in practice it can't
right now), we should call unregister_pernet_subsys(). Do that.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.6:
API:
- Convert remaining crypto_hash users to shash or ahash, also convert
blkcipher/ablkcipher users to skcipher.
- Remove crypto_hash interface.
- Remove crypto_pcomp interface.
- Add crypto engine for async cipher drivers.
- Add akcipher documentation.
- Add skcipher documentation.
Algorithms:
- Rename crypto/crc32 to avoid name clash with lib/crc32.
- Fix bug in keywrap where we zero the wrong pointer.
Drivers:
- Support T5/M5, T7/M7 SPARC CPUs in n2 hwrng driver.
- Add PIC32 hwrng driver.
- Support BCM6368 in bcm63xx hwrng driver.
- Pack structs for 32-bit compat users in qat.
- Use crypto engine in omap-aes.
- Add support for sama5d2x SoCs in atmel-sha.
- Make atmel-sha available again.
- Make sahara hashing available again.
- Make ccp hashing available again.
- Make sha1-mb available again.
- Add support for multiple devices in ccp.
- Improve DMA performance in caam.
- Add hashing support to rockchip"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: qat - remove redundant arbiter configuration
crypto: ux500 - fix checks of error code returned by devm_ioremap_resource()
crypto: atmel - fix checks of error code returned by devm_ioremap_resource()
crypto: qat - Change the definition of icp_qat_uof_regtype
hwrng: exynos - use __maybe_unused to hide pm functions
crypto: ccp - Add abstraction for device-specific calls
crypto: ccp - CCP versioning support
crypto: ccp - Support for multiple CCPs
crypto: ccp - Remove check for x86 family and model
crypto: ccp - memset request context to zero during import
lib/mpi: use "static inline" instead of "extern inline"
lib/mpi: avoid assembler warning
hwrng: bcm63xx - fix non device tree compatibility
crypto: testmgr - allow rfc3686 aes-ctr variants in fips mode.
crypto: qat - The AE id should be less than the maximal AE number
lib/mpi: Endianness fix
crypto: rockchip - add hash support for crypto engine in rk3288
crypto: xts - fix compile errors
crypto: doc - add skcipher API documentation
crypto: doc - update AEAD AD handling
...
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IEEE80211_RADIOTAP_VHT entry to rtap_namespace_sizes array in order to
define alignment and size of VHT info in tx radiotap
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, the supplicant will add the RRM capabilities
Information Element in the association request only if
Quiet period is supported (NL80211_FEATURE_QUIET).
Quiet is one of many RRM features, and there are other RRM
features that are not related to Quiet (e.g. neighbor
report). Therefore, requiring Quiet to enable RRM is too
restrictive.
Some of the features, like neighbor report, can be
supported by user space without any help from the kernel.
Hence adding the RRM capabilities IE to association request
should be the sole user space's decision.
Removing the RRM dependency on Quiet in the driver solves
this problem, but using an old driver with a user space
tool that would not require Quiet feature would be
problematic: the user space would add NL80211_ATTR_USE_RRM
in the association request even if the kernel doesn't
advertize NL80211_FEATURE_QUIET and the association would
be denied by the kernel.
This solution adds a global RRM capability, that tells user
space that it can request RRM capabilities IE publishment
without any specific feature support in the kernel.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This massively reduces data copying and thus improves rx performance
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
reuse_skb is set to true if the code decides to use the last segment.
Fixes a memory leak
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.
Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use skb_copy_bits in preparation for allowing fragmented skbs
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepararation for zero-copy A-MSDU support with page fragment SKBs
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Print a warning whenever an expected callback function
lacks implementation.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The connection keys are zeroed out in all other cases except this
one. Let's fix the last one as well.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
link/ether
when setting the interface down causes the wext message.
To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beniamino reported that he was getting an RTM_NEWLINK message for a
given interface, after the RTM_DELLINK for it. It turns out that the
message is a wireless extensions message, which was sent because the
interface had been connected and disconnection while it was deleted
caused a wext message.
For its netlink messages, wext uses RTM_NEWLINK, but the message is
without all the regular rtnetlink attributes, so "ip monitor link"
prints just rudimentary information:
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
link/ether
(from my hwsim reproduction)
This can cause userspace to get confused since it doesn't expect an
RTM_NEWLINK message after RTM_DELLINK.
The reason for this is that wext schedules a worker to send out the
messages, and the scheduling delay can cause the messages to get out
to userspace in different order.
To fix this, have wext register a netdevice notifier and flush out
any pending messages when netdevice state changes. This fixes any
ordering whenever the original message wasn't sent by a notifier
itself.
Cc: stable@vger.kernel.org
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch replaces uses of blkcipher with skcipher and the long
obsolete hash interface with ahash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of having this Kconfig option, which just *floods* the
kernel log,
* remove the per-channel prints that are fairly useless anyway
* convert the conditional printing to pr_debug()
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rule definitions here aren't really valid, they would
be rejected if it came from userspace due to the bandwidth
specified being bigger than the rule's width.
This is fairly much inconsequential since the other rules
around them do enable the bandwidth, but express that better
using the NL80211_RRF_AUTO_BW flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Free cached keys if the last early return path is taken.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Compared to cfg80211_rdev_free_wowlan in core.h,
the error goto label lacks the freeing of nd_config.
Fix that.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first leak occurs when entering the default case
in the switch for the initiator in set_regdom.
The second leaks a platform_device struct if the
platform registration in regulatory_init succeeds but
the sub sequent regulatory hint fails due to no memory.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The same piece of code appears at two places. Make a function from it.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a new station is added to AP/GO interfaces the default behaviour
is for it to be added authenticated and associated, due to backwards
compatibility. To prevent that, the driver must be able to do that
(setting the NL80211_FEATURE_FULL_AP_CLIENT_STATE feature flag) and
userspace must set the flag mask to auth|assoc and clear the set.
Handle this quirk in the API entirely in nl80211, and always push the
full flags to the drivers. NL80211_FEATURE_FULL_AP_CLIENT_STATE is
still required for userspace to be allowed to set the mask including
those bits, but after checking that add both flags to the mask and
set in case userspace didn't set them otherwise.
This obsoletes the mac80211 code handling this difference, no other
driver is currently using these flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix nl80211_set_station() to use the value of NL80211_ATTR_STA_AID
attribute instead of NL80211_ATTR_PEER_AID attribute.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement new functionality for aborting an ongoing scan.
Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Last caller of this function was removed in 3.17 in commit
97dc94f1d9.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This indicates a driver key selection issue, but even then there's
no point in printing it all the time, so ratelimit it. Also remove
the priv pointer from it -- people debugging will only have a single
device anyway and it's useless as anything but a cookie.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is a very simple wrapper around another one,
just adds a few default parameters, so replace it with a
static inline instead of using EXPORT_SYMBOL, reducing
the module size slightly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Complete the tracepoint with the missing data - it's not printed
by default (a lot of it is dynamic arrays) but will be recorded
and be available during post-processing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 rejects updates of AID and listen interval parameters
for existing entries. This information is known only at association stage
and as a result it's impossible to update entries that were added
unassociated.
Fix this by allowing updates of these properies for stations that the
driver (or mac80211) assigned unassociated state.
This then fixes mac80211's use of NL80211_FEATURE_FULL_AP_CLIENT_STATE.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If parse_acl_data succeeds but the subsequent parsing of smps
attributes fails, there will be a memory leak due to early returns.
Fix that by moving the ACL parsing later.
Cc: stable@vger.kernel.org
Fixes: 18998c381b ("cfg80211: allow requesting SMPS mode on ap start")
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is void and static, so just ifdef its contents
instead of duplicating the declaration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Printing "N/A mBi" is strange - print just "N/A" instead.
Also add a missing opening parenthesis.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of having a lot of places that free ignored requests
and then return REG_REQ_OK, make reg_process_hint() process
REG_REQ_IGNORE by freeing the request, and let functions it
calls return that instead of freeing.
This also fixes a leak when a second (different) country IE
hint was ignored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function can only deal with treatment values OK and ALREADY_SET
so make the callees not return anything else and warn if they do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a built-in regulatory database, there may be little point
in also calling out to CRDA and failing if the system is configured
that way. Allow removing CRDA support to save ~1K kernel size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the functions reg_set_rd_driver() and reg_set_rd_country_ie()
return with an error, the calling function already restores data
by calling restore_regulatory_settings(), so there's no need to
also schedule a timeout (which would lead to other side effects
such as indicating CRDA failed, which clearly isn't true.) Remove
the scheduling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of searching the built-in database only in the worker,
search it directly and return an error if the entry cannot be
found (or memory cannot be allocated.) This means that builtin
database queries no longer rely on the timeout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new name is more appropriate since in the case of a built-in
database it may not really rely on CRDA.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function reg_call_crda() can't actually validly return
REG_REQ_IGNORE as it does now when calling CRDA fails since
that return value isn't handled properly. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For location and connectivity services, userspace would often like
to know the time when the BSS was last seen. The current "last seen"
value is calculated in a way that makes it less useful, especially
if the system suspended in the meantime.
Add the ability for the driver to report a real CLOCK_BOOTTIME stamp
that can then be reported to userspace (if present).
Drivers wishing to use this must be converted to the new API to call
cfg80211_inform_bss_data() or cfg80211_inform_bss_frame_data(). They
need to ensure the reported value is accurate enough even when the
frame might have been buffered in the device (e.g. firmware.)
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[modified to use struct, inlines]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
-----BEGIN PGP SIGNATURE-----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=BF9F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, cfg80211 rejects capability updates for existing entries
and as a result it's impossible to update entries that were added
unassociated, but that is necessary to go through the full station
states from userspace, adding a station before authentication etc.
Fix this by allowing updates to capabilities for stations that the
driver (or mac80211) assigned unassociated state. Drivers setting
the full station state support flag must use the new station type
for proper operation.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition timing dependency between devices. This
patch enables wiphy device to suspend/resume asynchronously. This can
take advantage of multicore and improve system suspend/resume speed.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many drivers implement reading current TX power (using either cfg80211
or ieee80211 op) but userspace can't get it using nl80211. Right now the
only way to access it is to call some wext ioctl.
Let's put TX power in interface info reply (callback is wdev specific)
just like we do with current channel.
To be consistent (e.g. NL80211_CMD_SET_WIPHY) let's use mBm as na unit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow setting multicast rate on OCB interfaces.
Current behaviour results in EOPNOTSUPP when attempting this.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If driver failed to setup wiphy params (e.g. rts
threshold, fragmentation treshold) userspace
wasn't properly notified about this. This could
lead to user confusion who would think the command
succeeded even if that wasn't the case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original assumption of 20MHz wide channels hasn't been true since
the addition of support for 5 and 10 MHz channels.
Change the code to no longer disable all channels that don't fit into
the 20MHz grid, but instead set the appropriate flags to disable
operation on specific bandwidths.
Signed-off-by: Matthias May <matthias.may@neratec.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit eeca9fce1d ('cfg80211: Schedule timeout for all CRDA calls')
left behind a superfluous check after it removed some earlier code.
In reg_process_hint, the test of "treatment == REG_REQ_IGNORE ||
treatment == REG_REQ_ALREADY_SET" is superfluous because the code in the
if-then branch is identical to the code after the if statement.
Coverity CID #1295939
I also removed the unnecessary assignment of treatment in this case,
and added a comment reminding any future patch authors to ensure that
treatment is properly assigned before it is used after the switch.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This callback is currently not allowed to sleep, which makes it more
difficult to implement proper driver methods in mac80211 than it has
to be. Instead of doing asynchronous work here in mac80211, make it
possible for the callback to sleep by doing some asynchronous work
in cfg80211. This also enables improvements to other drivers, like
ath6kl, that would like to sleep in this callback.
While at it, also fix the code to call the driver on the implicit
unregistration when an interface is removed, and do that also when
a P2P-Device wdev is destroyed (otherwise we leak the structs.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RTNL is required to check for IR-relaxation conditions that allow
more channels to beacon. Export an RTNL locked version of reg_can_beacon
and use it where possible in AP/STA interface type flows, where
IR-relaxation may be applicable.
Fixes: 06f207fc54 ("cfg80211: change GO_CONCURRENT to IR_CONCURRENT for STA")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With a basic Linux userspace, the messages "Calling CRDA to update
world regulatory domain" appears 10 times after boot every second or
so, followed by a final "Exceeded CRDA call max attempts. Not calling
CRDA". For those of us not having the corresponding userspace parts,
having those messages repeatedly displayed at boot time is a bit
annoying, so this commit reduces their log level to pr_debug().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until recently, mac80211 overwrote all the statistics it could
provide when getting called, but it now relies on the struct
having been zeroed by the caller. This was always the case in
nl80211, but wext used a static struct which could even cause
values from one device leak to another.
Using a static struct is OK (as even documented in a comment)
since the whole usage of this function and its return value is
always locked under RTNL. Not clearing the struct for calling
the driver has always been wrong though, since drivers were
free to only fill values they could report, so calling this
for one device and then for another would always have leaked
values from one to the other.
Fix this by initializing the structure in question before the
driver method call.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691
Cc: stable@vger.kernel.org
Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible for mac80211 to be coerced into an
unexpected flow causing sdata union to become
corrupted. Station pointer was put into
sdata->u.vlan.sta memory location while it was
really master AP's sdata->u.ap.next_beacon. This
led to station entry being later freed as
next_beacon before __sta_info_flush() in
ieee80211_stop_ap() and a subsequent invalid
pointer dereference crash.
The problem was that ieee80211_ptr->use_4addr
wasn't cleared on interface type changes.
This could be reproduced with the following steps:
# host A and host B have just booted; no
# wpa_s/hostapd running; all vifs are down
host A> iw wlan0 set type station
host A> iw wlan0 set 4addr on
host A> printf 'interface=wlan0\nssid=4addrcrash\nchannel=1\nwds_sta=1' > /tmp/hconf
host A> hostapd -B /tmp/conf
host B> iw wlan0 set 4addr on
host B> ifconfig wlan0 up
host B> iw wlan0 connect -w hostAssid
host A> pkill hostapd
# host A crashed:
[ 127.928192] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c8
[ 127.929014] IP: [<ffffffff816f4f32>] __sta_info_flush+0xac/0x158
...
[ 127.934578] [<ffffffff8170789e>] ieee80211_stop_ap+0x139/0x26c
[ 127.934578] [<ffffffff8100498f>] ? dump_trace+0x279/0x28a
[ 127.934578] [<ffffffff816dc661>] __cfg80211_stop_ap+0x84/0x191
[ 127.934578] [<ffffffff816dc7ad>] cfg80211_stop_ap+0x3f/0x58
[ 127.934578] [<ffffffff816c5ad6>] nl80211_stop_ap+0x1b/0x1d
[ 127.934578] [<ffffffff815e53f8>] genl_family_rcv_msg+0x259/0x2b5
Note: This isn't a revert of f8cdddb8d6
("cfg80211: check iface combinations only when
iface is running") as far as functionality is
considered because b6a550156b ("cfg80211/mac80211:
move more combination checks to mac80211") moved
the logic somewhere else already.
Fixes: f8cdddb8d6 ("cfg80211: check iface combinations only when iface is running")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use dev_pm_ops instead of the legacy suspend/resume callbacks for the wiphy
class suspend and resume operations.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P GO was allowed on a channel because of the GO concurrent
relaxation, i.e., another station interface was associated to an AP on
the same channel or the same UNII band, and the station interface
disconnected from the AP, allow the following use cases unless the
channel is marked as indoor only and the device is not operating in an
indoor environment:
1. Allow the P2P GO to stay on its current channel. The rationale behind
this is that if the channel or UNII band were allowed by the AP they
could still be used to continue the P2P GO operation, and avoid connection
breakage.
2. Allow another P2P GO to start on the same channel or another channel
that is in the same UNII band as the previous instantiated P2P GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wpa_supplicant or authsae handles the mesh peering in user
space, but the plink state is still managed in kernel space.
Currently, there is no implementation by wpa_supplicant or
authsae to block the plink state after it is set to ESTAB.
By applying this patch, we can use the "iw mesh0 station set
<MAC address> plink_action block" to block the peer mesh STA.
This is useful for experimenting purposes.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change to only export WEXT symbols when required could break
the build if CONFIG_CFG80211_WEXT was explicitly disabled while
a driver like orinoco selected it.
Fix this by hiding the symbol when it's required so it can't be
disabled in that case.
Fixes: 2afe38d15c ("cfg80211-wext: export symbols only when needed")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the connect request from userspace didn't include an extended
capabilities IE, create one using the driver capabilities. This
fixes VHT associations, since those need to set the operating mode
notification capability.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patch eeca9fce1d (cfg80211: Schedule
timeout for all CRDA call) introduced a regression, where in case
that crda is not installed (or not configured properly etc.), the
regulatory core will needlessly continue to call it, polluting the
log with the following log:
"cfg80211: Calling CRDA to update world regulatory domain"
Fix this by limiting the number of continuous CRDA request failures.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seems Broadcom TDLS peers (Nexus 5, Xperia Z3) refuse to allow TDLS
connection when channel-switching is supported but the regulatory
classes IE is missing from the setup request.
Add a chandef to reg-class translation function to cfg80211 and use it
to add the required IE during setup. For now add only the current
regulatory class as supported - it is enough to resolve the
compatibility issue.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the initial net-detect delay (NL80211_ATTR_SCHED_SCAN_DELAY)
attribute in the WoWLAN info response.
Additionally, remove a bogus TODO comment.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
This helps debug issues with VLAN modifications that are otherwise
not really visible in any tracing/debugging.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that there are several regulatory requests
pending, but the processing of the last one does not call
CRDA, and thus the other requests are not handled.
Fix this by rescheduling the work until all requests have
been processed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Timeout was scheduled only in case CRDA was called due to user hints,
but was not scheduled for other cases. This can result in regulatory
hint processing getting stuck in case that there is no CRDA configured.
Change this by scheduling a timeout every time CRDA is called. In
addition, in restore_regulatory_settings() all pending requests are
restored (and not only the user ones).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the indoor setting configuration assumed that as
long as a station interface is connected, the indoor environment
setting does not change. However, this assumption is problematic
as:
- It is possible that a station interface is connected to a mobile
AP, e.g., softAP or a P2P GO, where it is possible that both the
station and the mobile AP move out of the indoor environment making
the indoor setting invalid. In such a case, user space has no way to
invalidate the setting.
- A station interface disconnection does not necessarily imply that
the device is no longer operating in an indoor environment, e.g.,
it is possible that the station interface is roaming but is still
stays indoor.
To handle the above, extend the indoor configuration API to allow
user space to indicate a change of indoor settings, and allow it to
indicate weather it controls the indoor setting, such that:
1. If the user space process explicitly indicates that it is going
to control the indoor setting, do not clear the indoor setting
internally, unless the socket is released. The user space process
should use the NL80211_ATTR_SOCKET_OWNER attribute in the command
to state that it is going to control the indoor setting.
2. Reset the indoor setting when restoring the regulatory settings in
case it is not owned by a user space process.
Based on the above, a user space tool that continuously monitors the
indoor settings, i.e., tracking power setting, location etc., can
indicate environment changes to the regulatory core.
It should be noted that currently user space is the only provided mechanism
used to hint to the regulatory core over the indoor/outdoor environment --
while the country IEs do have an environment setting this has been completely
ignored by the regulatory core by design for a while now since country IEs
typically can contain bogus data.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: ArikX Nemtsov <arik@wizery.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Directly update the indoor setting without wrapping it as
a regulatory request, to simplify the processing.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device supports waking up on 'any' signal - i.e. it continues
operating as usual and wakes up the host on pretty much anything that
happens, then it makes no sense to also configure the more restricted
WoWLAN mode where the device operates more autonomously but also in a
more restricted fashion.
Currently only cw2100 supports both 'any' and other triggers, but it
seems to be broken as it doesn't configure anything to the device, so
we can't currently get into a situation where both even can correctly
be configured. This is about to change (Intel devices are going to
support both and have different behaviour depending on configuration)
so make sure the conflicting modes cannot be configured.
(It seems that cw2100 advertises 'any' and 'disconnect' as a means of
saying that's what it will always do, but that isn't really the way
this API was meant to be used nor does it actually mean anything as
'any' always implies 'disconnect' already, and the driver doesn't
change device configuration in any way depending on the settings.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Operating classes 128-130 are defined in the 11ac
spec for the 5GHz band.
Update ieee80211_operating_class_to_band() to support them.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This modifies cfg80211_vendor_event_alloc() with an additional argument
struct wireless_dev *wdev. __cfg80211_alloc_event_skb() is modified to
take in *wdev argument, if wdev != NULL, both the NL80211_ATTR_IFINDEX
and wdev identifier are added to the vendor event.
These changes make it easier for drivers to add ifindex indication in
vendor events cleanly.
This also updates all existing users of cfg80211_vendor_event_alloc()
and __cfg80211_alloc_event_skb() in the kernel tree.
Signed-off-by: Ahmad Kholaif <akholaif@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_EXT_FEATURE_VHT_IBSS flag and VHT
support for IBSS.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using the wext compatibility code in cfg80211, part of the IEs
can be truncated if the passed user buffer is large enough for part
of the BSS but not large enough for all of the IEs. This can cause
an EAP network to show up as a PSK network.
Always return -E2BIG in this case to avoid truncating data.
Since this changes the control flow, use an on-stack variable for
a small buffer instead of allocating it.
Signed-off-by: James Minor <james.minor@ni.com>
[rework patch to error out immediately, use _check wrappers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both wpa_supplicant and mac80211 have and inactivity timer. By default
wpa_supplicant will be timed out in 5 minutes and mac80211's it is 30
minutes. If wpa_supplicant uses a longer timer than mac80211, it will
get unexpected disconnection by mac80211.
Using 0xffffffff instead as the configured value could solve this w/o
changing the code, but due to integer overflow in the expression used
this doesn't work. The expression is:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On 32bit system, the right side would overflow and be a very small
value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large,
causing unexpectedly early disconnections.
Instead allow disabling the inactivity timer to avoid this situation,
by passing the (previously invalid and useless) value 0.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword/rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a fully converted cfg80211 driver needs cfg80211-wext for
userspace API purposes, the symbols need not be exported. When
other drivers (orinoco/hermes or ipw2200) are enabled, they do
need the symbols exported as they use them directly.
Make those drivers select a new CFG80211_WEXT_EXPORT Kconfig
symbol (instead of just CFG80211_WEXT) and export the functions
only if requested - this saves about 1/2k due to the size of
EXPORT_SYMBOL() itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_exit should be called in cfg80211_init if nl80211_init succeeds
but regulatory_init or create_singlethread_workqueue fails.
Signed-off-by: Junjie Mao <junjie_mao@yeah.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently 8 rules in the world_regdom, but only the first 6
are applied due to an incorrect value for n_reg_rules. This causes
channels 149-165 and 60GHz to be disabled.
Signed-off-by: Jason Abele <jason@aether.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If monitor flags parsing results in active monitor but that
isn't supported, the already allocated message is leaked.
Fix this by moving the allocation after this check.
Reported-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently add nested members of the NL80211_ATTR_SCAN_FREQUENCIES
as NLA_U32 attributes of type NL80211_ATTR_WIPHY_FREQ in
cfg80211_net_detect_results. However, since there can be an arbitrary number of
frequency results, we should use the loop index of the loop used to add the
frequency results to NL80211_ATTR_SCAN_FREQUENCIES as the type (i.e. nla_type)
for each result attribute, rather than a fixed type.
This change is in line with how nested members are added to
NL80211_ATTR_SCAN_FREQUENCIES in the functions nl80211_send_wowlan_nd and
nl80211_add_scan_req.
Signed-off-by: Samuel Tan <samueltan@chromium.org>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes cfg80211 aware of the GCMP, GCMP-256, CCMP-256, BIP-GMAC-128,
BIP-GMAC-256, and BIP-CMAC-256 cipher suites. These new cipher suites
were defined in IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This cipher can be used only as a group management frame cipher and as
such, there is no point in validating that it is not used with non-zero
key-index. Instead, verify that it is not used as a pairwise cipher
regardless of the key index.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[change code to use switch statement which is easier to extend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* fix station double-removal when suspending while associating
* fix the HT (802.11n) header length calculation
* fix the CCK radiotap flag used for monitoring, a pretty
old regression but a simple one-liner
* fix per-station group-key handling
-----BEGIN PGP SIGNATURE-----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=DhIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Another set of last-minute fixes:
* fix station double-removal when suspending while associating
* fix the HT (802.11n) header length calculation
* fix the CCK radiotap flag used for monitoring, a pretty
old regression but a simple one-liner
* fix per-station group-key handling
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch warns that we once checked request->ssids in two functions
and then unconditionally used it later again.
This is actually fine, because the code has a relationship between
attrs[NL80211_ATTR_SCAN_SSIDS], n_ssids and request->ssids, but
smatch isn't smart enough to realize that.
Suppress the warnings by always checking just n_ssids - that way
smatch won't know that request->ssids could be NULL, and since it
is only NULL when n_ssids is 0 we still check everything correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case userspace attempts to obtain key information for or delete a
unicast key, this is currently erroneously rejected unless the driver
sets the WIPHY_FLAG_IBSS_RSN flag. Apparently enough drivers do so it
was never noticed.
Fix that, and while at it fix a potential memory leak: the error path
in the get_key() function was placed after allocating a message but
didn't free it - move it to a better place. Luckily admin permissions
are needed to call this operation.
Cc: stable@vger.kernel.org
Fixes: e31b82136d ("cfg80211/mac80211: allow per-station GTKs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT Control field may also be present in management frames, as defined
in 8.2.4.1.10 of 802.11-2012. Account for this in calculation of header
length.
Signed-off-by: Fred Chou <fred.chou.nd@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The userspace may want to delay the the first scheduled scan or
net-detect cycle. Add an optional attribute to the scheduled scan
configuration to pass the delay to be (optionally) used by the driver.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[add the attribute to the policy to validate it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Added new NL80211_ATTR_NETNS_FD which allows to
set namespace via nl80211 by fd.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* fix network-manager which was broken by the previous changes
* fix delete-station events, which were broken by me making the
genlmsg_end() mistake
* fix a timer left running during suspend in some race conditions
that would cause an annoying (but harmless) warning
* (less important, but in the tree already) remove 80+80 MHz rate
reporting since the spec doesn't distinguish it from 160 MHz;
as the bitrate they're both 160 MHz bandwidth
-----BEGIN PGP SIGNATURE-----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=Bvmr
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Some further updates for net-next:
* fix network-manager which was broken by the previous changes
* fix delete-station events, which were broken by me making the
genlmsg_end() mistake
* fix a timer left running during suspend in some race conditions
that would cause an annoying (but harmless) warning
* (less important, but in the tree already) remove 80+80 MHz rate
reporting since the spec doesn't distinguish it from 160 MHz;
as the bitrate they're both 160 MHz bandwidth
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ba1debdfed.
Oliver reported that it breaks network-manager, for some reason with
this patch NM decides that the device isn't wireless but "generic"
(ethernet), sees no carrier (as expected with wifi) and fails to do
anything else with it.
Revert this to unbreak userspace.
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value from nl80211_send_station() is the length of the
skb, or a negative error, so abort sending the message only when
the return value was negative.
This fixes the ibss_rsn wpa_supplicant test case.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
one for a deadlock in regulatory processing.
-----BEGIN PGP SIGNATURE-----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=bMKg
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-01-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Just two fixes - one for an uninialized variable and
one for a deadlock in regulatory processing.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have
* a lot of regulatory code changes to deal with the
way newer Intel devices handle this
* a change to drop packets while disconnecting from
an AP instead of trying to wait for them
* a new attempt at improving the tailroom accounting
to not kick in too much for performance reasons
* improvements in wireless link statistics
* many other small improvements and small fixes that
didn't seem necessary for 3.19 (e.g. in hwsim which
is testing only code)
-----BEGIN PGP SIGNATURE-----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=vaEW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-01-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Here's a big pile of changes for this round.
We have
* a lot of regulatory code changes to deal with the
way newer Intel devices handle this
* a change to drop packets while disconnecting from
an AP instead of trying to wait for them
* a new attempt at improving the tailroom accounting
to not kick in too much for performance reasons
* improvements in wireless link statistics
* many other small improvements and small fixes that
didn't seem necessary for 3.19 (e.g. in hwsim which
is testing only code)
Conflicts:
drivers/staging/rtl8723au/os_dep/ioctl_cfg80211.c
Minor overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are treated the same as 160 MHz in the spec, so
it makes no sense to distinguish them. As no driver uses them
yet, this is also not a problem, just remove them.
In the userspace API the field remains reserved to preserve
API and ABI.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send the netdetect configuration information in the response to
NL8021_CMD_GET_WOWLAN commands. This includes the scan interval,
SSIDs to match and frequencies to scan.
Additionally, add the NL80211_WOWLAN_TRIG_NET_DETECT with
NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a system contains only self-managed regulatory devices all hints
from the regulatory core are ignored. Stop hint processing early in this
case. These systems usually don't have CRDA deployed, which results in
endless (irrelevent) logs of the form:
cfg80211: Calling CRDA to update world regulatory domain
Make sure there's at least one self-managed device before discarding a
hint, in order to prevent initial hints from disappearing on CRDA
managed systems.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A self-managed device will sometimes need to set its regdomain synchronously.
Notably it should be set before usermode has a chance to query it. Expose
a new API to accomplish this which requires the RTNL.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The base for the current statistics is pretty mixed up, support
exporting RX/TX statistics for MSDUs per TID. This (currently)
covers received MSDUs, transmitted MSDUs and retries/failures
thereof.
Doing it per TID for MSDUs makes more sense than say only per AC
because it's symmetric - we could export per-AC statistics for all
frames (which AC we used for transmission can be determined also
for management frames) but per TID is better and usually data
frames are really the ones we care about. Also, on RX we can't
determine the AC - but we do know the TID for any QoS MPDU we
received.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add these two values:
* BEACON_RX: number of beacons received from this peer
* BEACON_SIGNAL_AVG: signal strength average for beacons only
These can then be used for Android Lollipop's statistics request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
* remove STATION_INFO_ASSOC_REQ_IES complete, but the length
(assoc_req_ies_len) can be used instead
* add NL80211_STA_INFO_RX_DROP_MISC which exists internally
but not in nl80211 yet
This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station is removed, its statistics may be interesting to
userspace, for example for further aggregation of statistics of
all stations that ever connected to an AP.
Introduce a new cfg80211_del_sta_sinfo() function (and make the
cfg80211_del_sta() a static inline calling it) to allow passing
a struct station_info along with this, and send the data in the
nl80211 event message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the time spent scanning to the survey data so it can be
reported by drivers that collect such information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not all devices are able to report survey data (particularly
time spent for various operations) per channel. As all these
statistics already exist in survey data, allow such devices
to report them (if userspace requested it)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P GO is active, the cfg80211_reg_can_beacon function will take
the wdev lock, in its call to cfg80211_go_permissive_chan. But the wdev lock
is already taken by the parent channel-checking function, causing a
deadlock.
Split the checking code into two parts. The first part will check if the
wdev is active and saves the channel under the wdev lock. The second part
will check actual channel validity according to type.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211.git to get some changes that would otherwise
cause conflicts with new changes coming here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the group names into the userspace API header file so that
userspace clients can use symbolic names from there instead of
hardcoding the actual names. This doesn't really change much,
but seems somewhat cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the wiphy::features flag being used up this patch adds a
new field wiphy::ext_features. Considering extensibility this
new field is declared as a byte array. This extensible flag is
exposed to user-space by NL80211_ATTR_EXT_FEATURES.
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 24a0aa212e.
It's causing severe userspace breakage. Namely, all the utilities from
wireless-utils which are relying on CONFIG_WEXT (which means tools like
'iwconfig', 'iwlist', etc) are not working anymore. There is a 'iw'
utility in newer wireless-tools, which is supposed to be a replacement
for all the "deprecated" binaries, but it's far away from being
massively adopted.
Please see [1] for example of the userspace breakage this is causing.
In addition to that, Larry Finger reports [2] that this patch is also
causing ipw2200 driver being impossible to build.
To me this clearly shows that CONFIG_WEXT is far, far away from being
"deprecated enough" to be removed.
[1] http://thread.gmane.org/gmane.linux.kernel/1857010
[2] http://thread.gmane.org/gmane.linux.network/343688
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An attribute NL80211_ATTR_SOCKET_OWNER can be set by the scan initiator.
If present, the attribute will cause the scan to be stopped if the client
dies.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because of possible races when accessing sched_scan_req pointer in
rdev, the sched_scan_req is converted to RCU pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The custom-reg handling function can currently only add flags to a given
channel. This results in stale flags being left applied. In some cases
a channel was disabled and even the orig_flags were changed to reflect
this.
Previously the API was designed for a single invocation before wiphy
registration, so this didn't matter. The previous approach doesn't scale
well to self-managed regulatory devices, particularly when a more
permissive regdom is applied after a restrictive one.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a device has self-managed regulatory, insist on returning the wiphy
specific regdomain if a wiphy-idx is specified. The global regdomain is
meaningless for such devices.
Also add an attribute for self-managed devices, so usermode can
distinguish them as such.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new regulatory flag that allows a driver to manage regdomain
changes/updates for its own wiphy.
A self-managed wiphys only employs regulatory information obtained from
the FW and driver and does not use other cfg80211 sources like
beacon-hints, country-code IEs and hints from other devices on the same
system. Conversely, a self-managed wiphy does not share its regulatory
hints with other devices in the system. If a system contains several
devices, one or more of which are self-managed, there might be
contradictory regulatory settings between them. Usage of flag is
generally discouraged. Only use it if the FW/driver is incompatible
with non-locally originated hints.
A new API lets the driver send a complete regdomain, to be applied on
its wiphy only.
After a wiphy-specific regdomain change takes place, usermode will get
a new type of change notification. The regulatory core also takes care
enforce regulatory restrictions, in case some interfaces are on
forbidden channels.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a wiphy-idx is specified, the kernel will return the wiphy specific
regdomain, if such exists. Otherwise return the global regdom.
When no wiphy-idx is specified, return the global regdomain as well as
all wiphy-specific regulatory domains in the system, via a new nested
list of attributes.
Add a new attribute for each wiphy-specific regdomain, for usermode to
identify it as such.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It allows to identify the wlan kind of device for the user application,
e.g.:
# ip -d link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 promiscuity 0
2: enp0s25: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff promiscuity 0
3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff promiscuity 0
wlan
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
[make wireless_link_ops const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ad-hoc requires beaconing for regulatory purposes. Validate that the
channel is valid for beaconing, and not only enabled.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can happen and there is no point in added more
detection code lower in the stack. Catching these in one
single point (cfg80211) is enough. Stop WARNING about this
case.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=89001
Cc: stable@vger.kernel.org
Fixes: 2f1c6c572d ("cfg80211: process non country IE conflicting first")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code assigns a constant value (a pointer to a static variable)
to an RCU pointer, which results in a sparse warning:
reg.c:112:10: warning: cast adds address space to expression (<asn:4>)
Suppress this warning by using __force.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the already-set and intersect case of a driver-hint, the previous
wiphy regdomain was not freed before being reset with a copy of the
cfg80211 regdomain.
Cc: stable@vger.kernel.org
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The VHT supported channel width field is a two bit integer, not a
bitfield. cfg80211_chandef_usable() was interpreting it incorrectly and
ended up rejecting 160 MHz channel width if the driver indicated support
for both 160 and 80+80 MHz channels.
Cc: stable@vger.kernel.org (3.16+)
Fixes: 3d9d1d6656 ("nl80211/cfg80211: support VHT channel configuration")
(however, no real drivers had 160 MHz support it until 3.16)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some variables are assigned unconditionally, remove their
initialisations to help avoid introducing errors later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the regulatory settings change, some channels might become invalid.
Disconnect interfaces acting on these channels, after giving userspace
code a grace period to leave them.
This mode is currently opt-in, and not all interface operating modes are
supported for regulatory-enforcement checks. A wiphy that wishes to use
the new enforcement code must specify an appropriate regulatory flag,
and all its supported interface modes must be supported by the checking
code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
[fix some indentation, typos]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This option has been marked for deprecation and removal for
a little more than two years, but it's not been very clearly
signalled since it was always possible to just select it.
Make it unselectable now to signal anyone who's still using
it after all this time more clearly. They can still get it
back, but only by patching the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of the cases for an invalid channel definition is that
the channel pointer is NULL, in which case the warning is
a bit late since we'll dereference the pointer. Bail out
of the function upon warning about this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Much of the code can be shared by moving it into helper functions
for the CQM event sending.
Also move the code closer together, even in the header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a channel pointer, and we use its center frequency
to look up a channel pointer - which will thus be exactly
the same as the original pointer.
Remove that pointless lookup and just use the pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let the other listeners being notified when a new or del interface
command has been issued, thus reducing later necessary request to be in
sync with current context.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace NL80211_ATTR_IFACE_SOCKET_OWNER attribute with more generic
NL80211_ATTR_SOCKET_OWNER that can be used with other commands
that interface creation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Callback add_virtual_intf is supposed to return ERR_PTR and trying to
return NULL results in some "Unable to handle kernel paging request",
etc. As it may be complicated to debug & trace, let's catch it (WARN).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Explicitly initialize the DFS state and beacon found state when handling
channels in the custom regulatory path.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some channels fields were not being updated in the custom regulatory
path. Update them according to the code in handle_channel().
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary feature flags and a scan flag to support using
random MAC addresses for scan while unassociated.
The configuration for this supports an arbitrary MAC address
value and mask, so that any kind of configuration (e.g. fixed
OUI or full 46-bit random) can be requested. Full 46-bit random
is the default when no other configuration is passed.
Also add a small helper function to use the addr/mask correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new WoWLAN API to enable net-detect as a wake up trigger.
Net-detect allows the device to scan in the background while the
host is asleep to wake up the host system when a matching network
is found.
Reuse the scheduled scan attributes to specify how the scan is
performed while suspended and the matches that will trigger a
wake event.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For net detect, we will need to reuse most of the scheduled scan
parsing function, but not all, so split out the attributes parsing
part out of the main start sched_scan function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce commands to initiate and cancel TDLS channel-switching. Once
TDLS channel-switching is started, the lower level driver is responsible
for continually initiating channel-switch operations and returning to
the base (AP) channel to listen for beacons from time to time.
Upon cancellation of the channel-switch all communication between the
relevant TDLS peers will continue on the base channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This brings in some mwifiex changes that further patches will
need to work on top to not cause merge conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow setting bandwidth related regulatory flags. These flags are mapped
to the corresponding channel flags in the specified range.
Make sure the new flags are consulted when calculating the maximum
bandwidth allowed by a regulatory-rule.
Also allow propagating the GO_CONCURRENT modifier from a reg-rule to a
channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-vif channel switches, we want to send
NL80211_CMD_CH_SWITCH_NOTIFY to the userspace to let it decide whether
other interfaces need to be moved as well. This is needed when we
want a P2P GO interface to follow the channel of a station, for
example.
Modify the code so that all interfaces can send CSA notifications.
Additionally, send notifications for STA CSA as well.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new NL80211_CH_SWITCH_STARTED_NOTIFY message that can be sent to
the userspace when a channel switch process has started. This allows
userspace to take action, for instance, by requesting other interfaces
to switch channel as necessary.
This patch introduces a function that allows the drivers to send this
notification. It should be used when the driver starts processing a
channel switch initiated by a remote device (eg. when a STA receives a
CSA from the AP) and when it successfully starts a userspace-triggered
channel switch (eg. when hostapd triggers a channel swith in the AP).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Netlink command for nl80211_send_mpath() should be NL80211_CMD_NEW_MPATH.
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most code avoids having a default case in interface type switch
statements already, to make it easier to find places that need
to be extended. Change the code in the __cfg80211_leave() and
nl80211_key_allowed() functions to not have a default case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The helper function can't ever create negative values, so use
u32 pointers as the function arguments as the caller does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
radar_detect_width is unused since commit 97dc94f1d9
("cfg80211: remove channel_switch combination check")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Keeps udev from mucking with things it shouldn't, since
the default MAC is never seen by udev when specified on
the cmd-line during creation.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[check for feature flag in nl80211 to force drivers to set it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kernel will attempt to use the name if it is supplied,
but if name cannot be used for some reason, the default
phyX name will be used instead.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[while at it, use wiphy_name() instead of dev_name(),
fix format string issue reported by Kees Cook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During the review of the corresponding wpa_supplicant patches we
noticed that the only way for it to detect that this functionality
is supported currently is to check for the command support. This
can be misleading though, as the command was also designed to, in
the future, support pure 802.11 TSPECs.
Expose the WMM-TSPEC feature flag to nl80211 so later we can also
expose an 802.11-TSPEC feature flag (if needed) to differentiate
the two cases.
Note: this change isn't needed in 3.18 as there's no driver there
yet that supports the functionality at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The optional NL80211_ATTR_MGMT_SUBTYPE and NL80211_ATTR_REASON_CODE
attributes can now be included in NL80211_CMD_DEL_STATION to indicate to
the driver which frame (Deauthentication/Disassociation) and reason code
in that frame should be used to indicate removal to the specific
station. This is used by drivers that implement AP SME and generate
those frames internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In kernel we have %*pE specifier to print an escaped buffer. All users
now switched to that approach.
This fixes a bug as well. The current implementation wrongly prints
octal numbers: only two first digits are used in case when 3 are
required and the rest of the string ends up cut off.
Additionally by default the \f, \v, \a, and \e are escaped to their
alphabetic representation. It's safe to do since it is currently used
for messaging only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "John W . Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ATM, specifying the frequency when connecting sends a void 'supported
rates' EID.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix memory leak in error path]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211 channel switch count attribute
(NL80211_ATTR_CH_SWITCH_COUNT) is specified as u32, but the
specification uses u8 for the counter. To make sure strange things
don't happen without informing the user, sanity check the value and
return -EINVAL if it doesn't fit in u8.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add two new cfg80211 operations for querying a table with proxied mesh
paths.
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add feature bits to indicate device support for
static-smps and dynamic-smps modes.
Add a new NL80211_ATTR_SMPS_MODE attribue to allow
configuring the smps mode to be used by the ap
(e.g. configuring to ap to dynamic smps mode will
reduce power consumption while having minor effect
on throughput)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace might need to know what queues are configured
for uapsd (e.g. for setting proper default values in tspecs).
Add this bitmap to the association event (inside wmm
nested attribute)
Add additional parameter to cfg80211_rx_assoc_resp,
and update its callers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add nl80211 and driver API to validate, add and delete traffic
streams with appropriate settings.
The API calls for userspace doing the action frame handshake
with the peer, and then allows only to set up the parameters
in the driver. To avoid setting up a session only to tear it
down again, the validate API is provided, but the real usage
later can still fail so userspace must be prepared for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clear any nl80211 messages that might contain keys after
processing them to avoid leaving their data in memory
"forever" after they've been freed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to put the values on the stack, just pass a
pointer to the data in the nl80211 message. This reduces stack
usage and avoids potential issues with putting sensitive data
on the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the keys stored for wireless extensions, clear the memory
to avoid having the key material stick around in memory "forever".
Similarly, when userspace overwrites a key, actually clear it instead
of just setting the key length to zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the connect keys, clear the memory to avoid
having the key material stick around in memory "forever".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable ACK timeout estimation algorithm (dynack) using mac80211
set_coverage_class API. Dynack is activated passing coverage class equals to -1
to lower drivers and it is automatically disabled setting valid value for
coverage class.
Define NL80211_ATTR_WIPHY_DYN_ACK flag attribute to enable dynack from
userspace. In order to activate dynack NL80211_FEATURE_ACKTO_ESTIMATION feature
flag must be set by lower drivers to indicate dynack capability.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regdom intersection code simply tries intersecting
each rule of the source with each rule of the target.
Since the resulting intersections are not observed
as a whole, this can result in multiple overlapping/duplicate
entries.
Make the rule addition a bit more smarter, by looking
for rules that can be contained within other rules,
and adding only extended ones.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flag attribute to use in associations, for tagging the target
connection as supporting RRM. It is the responsibility of upper
layers to set this flag only if both the underlying device, and the
target network indeed support RRM.
To be used in ASSOCIATE and CONNECT commands.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
In testmode and vendor command reply/event SKBs we use the
skb cb data to store nl80211 parameters between allocation
and sending. This causes the code for CONFIG_NETLINK_MMAP
to get confused, because it takes ownership of the skb cb
data when the SKB is handed off to netlink, and it doesn't
explicitly clear it.
Clear the skb cb explicitly when we're done and before it
gets passed to netlink to avoid this issue.
Cc: stable@vger.kernel.org [this goes way back]
Reported-by: Assaf Azulay <assaf.azulay@intel.com>
Reported-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few possible cases of where BSS data came from:
1) only a beacon has been received
2) only a probe response has been received
3) the driver didn't report what it received (this happens when
using cfg80211_inform_bss[_width]())
4) both probe response and beacon data has been received
Unfortunately, in the userspace API, a few things weren't there:
a) there was no way to differentiate cases 1) and 4) above
without comparing the data of the IEs
b) the TSF was always from the last frame, instead of being
exposed for beacon/probe response separately like IEs
Fix this by
i) exporting a new flag attribute that indicates whether or
not probe response data has been received - this addresses (a)
ii) exporting a BEACON_TSF attribute that holds the beacon's TSF
if a beacon has been received
iii) not exporting the beacon attributes in case (3) above as that
would just lead userspace into thinking the data actually came
from a beacon when that isn't clear
To implement this, track inside the IEs struct whether or not it
(definitely) came from a beacon.
Reported-by: William Seto
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit dda444d524.
Channel switching code has been reworked and
improved significantly since the time original
locking issues were found.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently it can send regulatory domain change notification before any
NEW_WIPHY notification. Moreover, if rfill_register() fails, calling
wiphy_unregister() will send a DEL_WIPHY though no NEW_WIPHY had been
sent previously.
Thus reordering so it properly notifies NEW_WIPHY before any other.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "wireless-regdb: remove antenna gain" was merged in the
wireless-regdb tree, the awk script parser has been incompatible
with the 'official' regulatory database. This fixes that up.
Without this change the max EIRP is set to 0 making 802.11 devices
useless.
The fragile nature of the awk parser must be replaced, but ideas
over how to do that in the most scalable way are being reviewed.
In the meantime update the documentation for CFG80211_INTERNAL_REGDB
so folks are aware of expectations for now.
Reported-by: John Walker <john@x109.net>
Reported-by: Krishna Chaitanya <chaitanya.mgit@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some VHT TDLS peers (Google Nexus 5) include the VHT-AID IE in their
TDLS setup request/response. Usermode passes this aid as the station
aid, causing it to fail verifiction, since this happens in the
"set_station" stage. Make an exception for the TDLS use-case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
tsc can be NULL (mac80211 currently always passes NULL),
resulting in NULL-dereference. check before copying it.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver is now responsible for veryfing if the
switch is possible.
Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().
This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The non-split wiphy state shouldn't be increased in size
so move the new set_qos_map command into the split if
statement.
Cc: stable@vger.kernel.org (3.14+)
Fixes: fa9ffc7456 ("cfg80211: Add support for QoS mapping")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MAX_JIFFY_OFFSET has no meaning when calculating the
elapsed jiffies, as jiffies run out until ULONG_MAX.
This miscalculation results in erroneous values
in case of a wrap-around.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8eca1fb692.
Felix notes that this broke regulatory, leaving channel 12 open for AP
operation in the US regulatory domain where it isn't permitted.
Link: http://mid.gmane.org/53A6C0FF.9090104@openwrt.org
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.
CC [M] net/wireless/wext-sme.o
CC [M] net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2
Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The firmware / low level driver can parse the channel in
the DS IE or HT IE and compensate the RSSI so that it will
still have a valid value even if we heard the frame on an
adjacent channel. This can be done up to a certain offset.
Add this offset as a configuration for the low level driver.
A low level driver that can compensate the low RSSI in this
case should assign the maximal offset for which the RSSI
value is still valid.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise every "indoor" setting by usermode will cause a regdomain reset.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement and export the new cfg80211_get_station() API.
This utility can be used by other kernel modules to obtain
detailed information about a given wireless station.
It will be in particular useful to batman-adv which will
implement a wireless rate based metric.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may need information about the expected throughput
towards a given peer.
This value is supposed to consider the size overhead
generated by the 802.11 header.
This value is exported in kbps through the get_station() API
by including it into the station_info object.
Moreover, it is sent to user space when replying to the
nl80211 GET_STATION command.
This information will be useful to the batman-adv module
which will use it for its new metric computation.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires changing the nl80211 parsing code a bit to use
intermediate pointers for the allocation, but clarifies the
API towards the drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the type of NL80211_ATTR_CSA_C_OFF_BEACON and
NL80211_ATTR_CSA_C_OFF_PRESP to be NLA_BINARY which allows
userspace to use beacons and probe responses with
multiple CSA counters.
This isn't breaking the API since userspace can
continue to use nla_put_u16 for this attributes, which
is equivalent to a single element u16 array.
In addition advertise max number of supported CSA counters.
This is needed when using CSA and eCSA IEs together.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_ATTR_CSA_C_OFFSETS_TX which holds an array
of offsets to the CSA counters which should be updated
when sending a management frames with NL80211_CMD_FRAME.
This API should be used by the drivers that wish to keep the
CSA counter updated in probe responses, but do not implement
probe response offloading and so, do not use
ieee80211_proberesp_get function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to pass NL80211_IFTYPE_UNSPECIFIED when calling
cfg80211_chandef_dfs_required() since we always already have the
interface type. So, pass the actual interface type instead.
Additionally, have cfg80211_chandef_dfs_required() WARN if the passed
interface type is NL80211_IFTYPE_UNSPECIFIED, so we can detect
problems more easily.
Tested-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the moment, the ath9k/ath10k DFS module only supports detecting ETSI
radar patterns.
Add a bitmap in the interface combinations, indicating which DFS regions
are supported by the detector. If unset, support for all regions is
assumed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation")
Cc: stable@vger.kernel.org (3.10+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These really can't trigger unless somebody messes up the code,
but don't make debugging it needlessly complicated, WARN and
return instead of BUG_ON().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>