This patch fix possible kernel crash if no platform data supplied.
We should not use platform data in this case, instead we will use
default values from private driver structure.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver supports the RocketPort EXPRESS and RocketPort INFINITY
families of PCI/PCIe multiport serial adapters. These adapters use a
"RocketPort 2" ASIC that is not compatible with the original RocketPort
driver (CONFIG_ROCKETPORT).
Tested with the RocketPort EXPRESS Octa DB9 and Quad DB9. Also added an
old RocketPort 8J PCI card to the same system to verify that rocket.c and
rp2.c coexist peacefully.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matching PCI_ANY_ID causes conflicts with RocketPort 2 adapters, which
are supported by a different driver.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory mapped via ioremap call is never released. Rather than add an
iounmap call, change allocation function to devm_request_and_ioremap.
Also, change the error on failure for this call to -EADDRNOTAVAIL rather than
-ENOMEM.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two instances where the index to vt8500_uart_ports is tested
against > VT8500_MAX_PORTS. Correct usage should be >= VT8500_MAX_PORTS.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer tty is dereferened in line 3135, so it is not necessary to check
null again in line 3140.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer info is dereferened in line 1009, so it is not necessary to check
null again in line 1012.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Original table in OMAP TRM named "UART Mode Baud Rates, Divisor
Values, and Error Rates" determines modes not for all common baud
rates. E.g. for 1000000 baud rate mode should be 16x, but according to
that table it's determined as 13x. According to current implementation
of mode divisor selection, after requesting 1000000 baudrate from
driver, later one will configure chip to use MODE13 divisor. Assuming
48Mhz as common UART clock speed, MODE13 divisor will effectively give
1230769 baudrate, what is quite far from desired 1000000 baudrate.
While with MODE16 divisor, chip will produce exact 1000000 baudrate.
In old driver that served UART devices (8250.c and serial_core.c) this
divisor could have been configured by user-space program, but in
omap_serial.c driver implementation this ability was not implemented
(afaik, by design) thus disallowing proper usage of MODE16-compatible
baudrates.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "serial/arc-uart: split probe from probe_earlyprintk" introduced
a build time warning:
"WARNING: vmlinux.o(.data+0x5baa0): Section mismatch in reference from
the variable early_arc_platform_driver to the function
.init.text:arc_serial_probe_earlyprintk()"
While at it - fixed another incorrectly placed initdata annotation.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: fengguang.wu@intel.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fast lookup table to set baudrate is only right when ioclk
is 150MHz. for most platforms, ioclk is 150MHz, but some boards
might set ioclk to other frequency.
so re-calc the clk_div_reg when ioclk is not 150MHz. this patch
also gets clk in probe and puts it in remove.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sb105x driver calls parport_pc_probe_port() which isn't defined if
PARPORT_PC isn't enabled. Protecting it with CONFIG_PARPORT is not good
enough, must protect it with CONFIG_PARPORT_PC.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2e254212 broke listing of available network names, since it
clamped the length of the returned SSID to WLAN_BSSID_LEN (6) instead of
WLAN_SSID_MAXLEN (32).
https://bugzilla.kernel.org/show_bug.cgi?id=52501
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two tiny fixes
* A build warning fix due to signed / unsigned comparison
* Missing sign extension in adis16080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=t+tK
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of fixes for IIO post 3.8-rc1
Two tiny fixes
* A build warning fix due to signed / unsigned comparison
* Missing sign extension in adis16080
Guests can trigger MMIO exits using dcbf. Since we don't emulate cache
incoherent MMIO, just do nothing and move on.
Reported-by: Ben Collins <ben.c@servergy.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Ben Collins <ben.c@servergy.com>
CC: stable@vger.kernel.org
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bbb63c514a (drivers:tty:fix up
ENOIOCTLCMD error handling) changed the default return value from tty
ioctl to be ENOTTY and not EINVAL. This is appropriate.
But in case of TIOCGPTN for the old BSD ptys glibc started failing
because it expects EINVAL to be returned. Only then it continues to
obtain the pts name the other way around.
So fix this case by explicit return of EINVAL in this case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Florian Westphal <fw@strlen.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # 3.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt6656 has several headers that use the #pragma pack(1) directive to
enable structure packing, but never disable it. The layout of
structures defined in other headers can then depend on which order the
various headers are included in, breaking the One Definition Rule.
In practice this resulted in crashes on x86_64 until the order of header
inclusion was changed for some files in commit 11d404cb56 ('staging:
vt6656: fix headers and add cfg80211.'). But we need a proper fix that
won't be affected by future changes to the order of inclusion.
This removes the #pragma pack(1) directives and adds __packed to the
structure definitions for which packing appears to have been intended.
Reported-and-tested-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The send buffer was being leaked; fix it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is bug in the definition of struct dm_info_msg. This patch fixes
the definition of this structure and makes the corresponding adjustments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull more s390 patches from Martin Schwidefsky:
"A couple of bug fixes: one of the transparent huge page primitives is
broken, the sched_clock function overflows after 417 days, the XFS
module has grown too large for -fpic and the new pci code has broken
normal channel subsystem notifications."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/chsc: fix SEI usage
s390/time: fix sched_clock() overflow
s390: use -fPIC for module compile
s390/mm: fix pmd_pfn() for thp
The variables mapping,index are initialized but never used
otherwise, so remove the unused variables.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix the following sparse warning:
fs/fuse/file.c:2249:6: warning: symbol 'fuse_file_fallocate' was not declared. Should it be static?
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Given that CUSE depends on FUSE, it only makes sense to move its
Kconfig entry into the FUSE Kconfig file. Also, add a few grammatical
and semantic touchups.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix the following compiler warnings:
fs/fuse/cuse.c: In function 'cuse_process_init_reply':
fs/fuse/cuse.c:288:24: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
fs/fuse/cuse.c:272:14: note: 'val' was declared here
fs/fuse/cuse.c:284:10: warning: 'key' may be used uninitialized in this function [-Wmaybe-uninitialized]
fs/fuse/cuse.c:272:8: note: 'key' was declared here
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Sysfs doesn't allow two devices with the same name, but we register a
sysfs entry for each cuse device without checking for name collisions.
This extends the registration to first check whether the name was already
registered.
To avoid race-conditions between the name-check and linking the device, we
need to protect the whole registration with a mutex.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
We need to check for name-collisions during cuse-device registration. To
avoid race-conditions, this needs to be protected during the whole device
registration. Therefore, replace the spinlocks by mutexes first so we can
safely extend the locked regions to include more expensive or sleeping
code paths.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The gpio_chip.label field is a const char * and assigned the value of a
call to dev_name(). Memory obtained from dev_name() should not be freed
by drivers.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since exynos5440 can support pinctrl so skip the legacy
gpiolib registration. If not, happens following.
WARNING: at drivers/gpio/gpio-samsung.c:3102 samsung_gpiolib_init+0x68/0x8c()
Unknown SoC in gpio-samsung, no GPIOs added
Acked-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We stopped reading FORCEWAKE for posting reads in
commit 8dee3eea3c
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Sat Sep 1 22:59:50 2012 -0700
drm/i915: Never read FORCEWAKE
and started using something from the same cacheline instead. On the
bug reporter's machine this broke entering rc6 states after a
suspend/resume cycle. It turns out reading ECOBUS as posting read
worked fine, while GTFIFODBG did not, preventing RC6 states after
suspend/resume per the bug report referenced below. It's not entirely
clear why, but clearly GTFIFODBG was nowhere near the same cacheline
or address range as FORCEWAKE.
Trying out various registers for posting reads showed that all tested
registers for which NEEDS_FORCE_WAKE() (in i915_drv.c) returns true
work. Conversely, most (but not quite all) registers for which
NEEDS_FORCE_WAKE() returns false do not work. Details in the referenced
bug.
Based on the above, add posting reads on ECOBUS where GTFIFODBG was
previously relied on.
In true cargo cult spirit, add posting reads for FORCEWAKE_VLV writes as
well, but instead of ECOBUS, use FORCEWAKE_ACK_VLV which is in the same
address range as FORCEWAKE_VLV.
v2: Add more details to the commit message. No functional changes.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52411
Reported-and-tested-by: Alexander Bersenev <bay@hackerdom.ru>
CC: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: add cc: stable and make the commit message a bit clearer that
this is a regression fix and what exactly broke.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes following warning:
drivers/gpio/gpio-samsung.c:450:32: warning: 'exynos_gpio_cfg' defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2450:33: warning: 'exynos5_gpios_1' defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2618:33: warning: 'exynos5_gpios_2' defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2679:33: warning: 'exynos5_gpios_3' defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2715:33: warning: 'exynos5_gpios_4' defined but not used [-Wunused-variable]
Because current gpio-samsung is valid only on EXYNOS5250.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since EXYNOS5440 can select PINCTRL_EXYNOS5440 without PINCTRL_SAMSUNG,
it should be fixed. In detail, PINCTRL_SAMSUNG is a kind of frame work
for supporting pinctrl on most Samsung SoCs including S3C, S5P as well
except EXYNOS5440 so PINCTRL_EXYNOS5440 has been implemented separated.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Issuing a "reboot" command after the LCD times out causes the following
warnings:
Requesting system reboot
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:471 clk_disable+0x24/0x50()
Modules linked in:
[<c001ad90>] (unwind_backtrace+0x0/0xf4) from [<c0025aac>] (warn_slowpath_common+0x48/0x60)
[<c0025aac>] (warn_slowpath_common+0x48/0x60) from [<c0025ae0>] (warn_slowpath_null+0x1c/0x24)
[<c0025ae0>] (warn_slowpath_null+0x1c/0x24) from [<c03960a0>] (clk_disable+0x24/0x50)
[<c03960a0>] (clk_disable+0x24/0x50) from [<c02695a0>] (imxfb_disable_controller+0x48/0x7c)
[<c02695a0>] (imxfb_disable_controller+0x48/0x7c) from [<c029d838>] (platform_drv_shutdown+0x18/0x1c)
[<c029d838>] (platform_drv_shutdown+0x18/0x1c) from [<c02990fc>] (device_shutdown+0x48/0x14c)
[<c02990fc>] (device_shutdown+0x48/0x14c) from [<c003d09c>] (kernel_restart_prepare+0x2c/0x3c)
[<c003d09c>] (kernel_restart_prepare+0x2c/0x3c) from [<c003d0e4>] (kernel_restart+0xc/0x48)
[<c003d0e4>] (kernel_restart+0xc/0x48) from [<c003d1e8>] (sys_reboot+0xc0/0x1bc)
[<c003d1e8>] (sys_reboot+0xc0/0x1bc) from [<c0014ca0>] (ret_fast_syscall+0x0/0x2c)
---[ end trace da6b502ca79c854f ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:380 clk_unprepare+0x1c/0x2c()
Modules linked in:
[<c001ad90>] (unwind_backtrace+0x0/0xf4) from [<c0025aac>] (warn_slowpath_common+0x48/0x60)
[<c0025aac>] (warn_slowpath_common+0x48/0x60) from [<c0025ae0>] (warn_slowpath_null+0x1c/0x24)
[<c0025ae0>] (warn_slowpath_null+0x1c/0x24) from [<c0396338>] (clk_unprepare+0x1c/0x2c)
[<c0396338>] (clk_unprepare+0x1c/0x2c) from [<c02695a8>] (imxfb_disable_controller+0x50/0x7c)
[<c02695a8>] (imxfb_disable_controller+0x50/0x7c) from [<c029d838>] (platform_drv_shutdown+0x18/0x1c)
[<c029d838>] (platform_drv_shutdown+0x18/0x1c) from [<c02990fc>] (device_shutdown+0x48/0x14c)
[<c02990fc>] (device_shutdown+0x48/0x14c) from [<c003d09c>] (kernel_restart_prepare+0x2c/0x3c)
[<c003d09c>] (kernel_restart_prepare+0x2c/0x3c) from [<c003d0e4>] (kernel_restart+0xc/0x48)
[<c003d0e4>] (kernel_restart+0xc/0x48) from [<c003d1e8>] (sys_reboot+0xc0/0x1bc)
[<c003d1e8>] (sys_reboot+0xc0/0x1bc) from [<c0014ca0>] (ret_fast_syscall+0x0/0x2c)
---[ end trace da6b502ca79c8550 ]---
------------[ cut here ]------------
This happens because "reboot" triggers imxfb_shutdown(), which calls
imxfb_disable_controller with the clocks already disabled.
To prevent this, add a clock enabled status so that we can check if the clocks
are enabled before disabling them.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Kukjin Kim:
That branch fixes build error for S3C24XX/S3C64xx. And corrects dw-mshc
properties on EXYNOS5 DT and fixes IRQ mapping on Cragganmore board.
* 'v3.8-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Fix up IRQ mapping for balblair on Cragganmore
ARM: dts: correct the dw-mshc timing properties as per binding
ARM: S3C64XX: Fix build error with CONFIG_S3C_DEV_FB disabled
+ Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
- fix(es) for compound buffers
- fix for dquot soft timer asserts due to overflow of d_blk_softlimit
- fix for regression in dir v2 code introduced in commit 20f7e9f3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=gA4q
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v3.8-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
- fix(es) for compound buffers
- fix for dquot soft timer asserts due to overflow of d_blk_softlimit
- fix for regression in dir v2 code introduced in commit 20f7e9f372
("xfs: factor dir2 block read operations")
* tag 'for-linus-v3.8-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: recalculate leaf entry pointer after compacting a dir2 block
xfs: remove int casts from debug dquot soft limit timer asserts
xfs: fix the multi-segment log buffer format
xfs: fix segment in xfs_buf_item_format_segment
xfs: rename bli_format to avoid confusion with bli_formats
xfs: use b_maps[] for discontiguous buffers
We are using S3C_EINT(4) instead of S3C_EINT(5).
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As per the current exynos-dw-mshc bindings, dw-mshc-sdr-timing and
dw-mshc-ddr-timing properties are having only two cells, these properties
are wrongly set for exynos5250 based cros5250 and smdk5250 platfroms. This
patch corrects above timing propreties for above platfroms
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If there is no board selecting CONFIG_S3C_DEV_FB enabled, build will
fail on arch/arm/mach-s3c64xx/pm.c, where s3c_device_fb is referenced.
This patch adds ifdef guard around the code making it compile only
when CONFIG_S3C_DEV_FB is enabled.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* cpuidle initialization regression fix from Krzysztof Mazur.
* cpuidle fix for power usage fields handling from Daniel Lezcano.
* ACPI build fix from Yinghai Lu.
-
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=4ifX
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- cpuidle regression fix related to the initialization of state
kobjects from Krzysztof Mazur.
- cpuidle fix removing some not very useful code and making some
user-visible problems go away at the same time. From Daniel Lezcano.
- ACPI build fix from Yinghai Lu.
* tag 'pm+acpi-for-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: remove the power_specified field in the driver
ACPI / glue: Fix build with ACPI_GLUE_DEBUG set
cpuidle: fix number of initialized/destroyed states
debug_ll_addr is only used on machines with an MMU so it can be #ifdef'ed
out safely. This fixes:
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:104: Error: too many positional arguments
The problem was introduced in e5c5f2a ARM: implement debug_ll_io_init().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Jones hit this assert when doing a compile on recent git, with
CONFIG_XFS_DEBUG enabled:
XFS: Assertion failed: (char *)dup - (char *)hdr == be16_to_cpu(*xfs_dir2_data_unused_tag_p(dup)), file: fs/xfs/xfs_dir2_data.c, line: 828
Upon further digging, the tag found by xfs_dir2_data_unused_tag_p(dup)
contained "2" and not the proper offset, and I found that this value was
changed after the memmoves under "Use a stale leaf for our new entry."
in xfs_dir2_block_addname(), i.e.
memmove(&blp[mid + 1], &blp[mid],
(highstale - mid) * sizeof(*blp));
overwrote it.
What has happened is that the previous call to xfs_dir2_block_compact()
has rearranged things; it changes btp->count as well as the
blp array. So after we make that call, we must recalculate the
proper pointer to the leaf entries by making another call to
xfs_dir2_block_leaf_p().
Dave provided a metadump image which led to a simple reproducer
(create a particular filename in the affected directory) and this
resolves the testcase as well as the bug on his live system.
Thanks also to dchinner for looking at this one with me.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The int casts here make it easy to trigger an assert with a large
soft limit. For example, set a >4TB soft limit on an empty volume
to reproduce a (0 > -x) comparison due to an overflow of
d_blk_softlimit.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Per Dave Chinner suggestion, this patch:
1) Corrects the detection of whether a multi-segment buffer is
still tracking data.
2) Clears all the buffer log formats for a multi-segment buffer.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Not every segment in a multi-segment buffer is dirty in a
transaction and they will not be outputted. The assert in
xfs_buf_item_format_segment() that checks for the at least
one chunk of data in the segment to be used is not necessary
true for multi-segmented buffers.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Rename the bli_format structure to __bli_format to avoid
accidently confusing them with the bli_formats pointer.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Commits starting at 77c1a08 introduced a multiple segment support
to xfs_buf. xfs_trans_buf_item_match() could not find a multi-segment
buffer in the transaction because it was looking at the single segment
block number rather than the multi-segment b_maps[0].bm.bn. This
results on a recursive buffer lock that can never be satisfied.
This patch:
1) Changed the remaining b_map accesses to be b_maps[0] accesses.
2) Renames the single segment b_map structure to __b_map to avoid
future confusion.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
This fixes CVE-2013-0190 / XSA-40
There has been an error on the xen_failsafe_callback path for failed
iret, which causes the stack pointer to be wrong when entering the
iret_exc error path. This can result in the kernel crashing.
In the classic kernel case, the relevant code looked a little like:
popl %eax # Error code from hypervisor
jz 5f
addl $16,%esp
jmp iret_exc # Hypervisor said iret fault
5: addl $16,%esp
# Hypervisor said segment selector fault
Here, there are two identical addls on either option of a branch which
appears to have been optimised by hoisting it above the jz, and
converting it to an lea, which leaves the flags register unaffected.
In the PVOPS case, the code looks like:
popl_cfi %eax # Error from the hypervisor
lea 16(%esp),%esp # Add $16 before choosing fault path
CFI_ADJUST_CFA_OFFSET -16
jz 5f
addl $16,%esp # Incorrectly adjust %esp again
jmp iret_exc
It is possible unprivileged userspace applications to cause this
behaviour, for example by loading an LDT code selector, then changing
the code selector to be not-present. At this point, there is a race
condition where it is possible for the hypervisor to return back to
userspace from an interrupt, fault on its own iret, and inject a
failsafe_callback into the kernel.
This bug has been present since the introduction of Xen PVOPS support
in commit 5ead97c84 (xen: Core Xen implementation), in 2.6.23.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com>
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In commit 281dc5c5ec ("Give up on pushing CC_OPTIMIZE_FOR_SIZE") we
already changed the actual default value, but the help-text still
suggested 'y'. Fix the help text too, for all the same reasons.
Sadly, -Os keeps on generating some very suboptimal code for certain
cases, to the point where any I$ miss upside is swamped by the downside.
The main ones are:
- using "rep movsb" for memcpy, even on CPU's where that is
horrendously bad for performance.
- not honoring branch prediction information, so any I$ footprint you
win from smaller code, you lose from less code density in the I$.
- using divide instructions when that is very expensive.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the build error:
drivers/built-in.o: In function `twl_probe':
drivers/mfd/twl-core.c:1256: undefined reference to `devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[ Samuel is busy, taking it directly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
