Find and unwrap wrapped strings in the style:
pr_debug("clockdomain: hardware cannot set/clear wake up of "
"%s when %s wakes up\n", clkdm1->name, clkdm2->name);
Keeping these strings contiguous seems to be the current Linux kernel
policy.
The offending lines were found with the following command:
pcregrep -rnM '"\s*$\s*"' arch/arm/*omap*
While here, some messages have been clarified, some pr_warning(
... calls have been converted to pr_warn( ..., and some printk(KERN_*
... have been converted to pr_*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
On OMAP4, recently a synchronisation bug is discovered by hardware
team, which leads to incorrect timer value read from 32K sync timer
IP when the IP is comming out of idle.
The issue is due to the synchronization methodology used in the SYNCTIMER IP.
The value of the counter register in 32kHz domain is synchronized to the OCP
domain register only at count up event, and if the OCP clock is switched off,
the OCP register gets out of synch until the first count up event after the
clock is switched back -at the next falling edge of the 32kHz clock.
Further investigation revealed that it applies to gptimer1 and watchdog timer2
as well which may run on 32KHz. This patch fixes the issue for all the
applicable modules.
The BUG has not made it yet to the OMAP errata list and it is applicable to
OMAP1/2/3/4/5. OMAP1/2/3 it is taken care indirectly by autodeps.
By enabling static depedency of wakeup clockdomain with MPU, as soon as MPU
is woken up from lowpower state(idle) or whenever MPU is active, PRCM forces
the OCP clock to be running and allow the counter value to be updated properly
in the OCP clock domain.
The bug is going to fixed in future OMAP versions.
Reported-Tested-by: dave.long@linaro.org
[dave.long@linaro.org: Reported the oprofile time stamp issue with synctimer
and helped to test this patch]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The platform_suspend_ops can be shared across OMAP2, 3, and 4, along
with all of the functions referenced in that structure. This patch
shares them. It also removes the suspend_state file-scoped variable
in the OMAP2 and 3 PM code; it does not appear to be actually needed
by anything.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[khilman@ti.com: minor rework needed due to rebase/merge with conflicting changes]
Signed-off-by: Kevin Hilman <khilman@ti.com>
clkdms_setup() is identical across OMAP2, 3, and 4, so share it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that all implementations of arch_idle() are equivalent to cpu_do_idle()
we can just use the later directly and stop including mach/system.h.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add OMAP4 CPUIDLE support. CPU1 is left with defualt idle and
the low power state for it is managed via cpu-hotplug.
This patch adds MPUSS low power states in cpuidle.
C1 - CPU0 ON + CPU1 ON + MPU ON
C2 - CPU0 OFF + CPU1 OFF + MPU CSWR
C3 - CPU0 OFF + CPU1 OFF + MPU OSWR
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWr.
Ofcourse when MPUSS and CORE PD transitions to OSWR along with device
off mode, even the memory contemts are lost which is as good as
the PD off state.
On OMAP4 because of hardware constraints, no low power states are
targeted when both CPUs are online and in SMP mode. The low power
states are attempted only when secondary CPU gets offline to OFF
through hotplug infrastructure.
Thanks to Nicole Chalhoub <n-chalhoub@ti.com> for doing exhaustive
C-state latency profiling.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the MPUSS OSWR (Open Switch Retention) support. The MPUSS
OSWR configuration is as below.
- CPUx L1 and logic lost, MPUSS logic lost, L2 memory is retained
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWR.
On OMAP4430 secure devices too, MPUSS off mode can't be used because of
a bug which alters Ducati and Tesla states. Hence MPUSS off mode as an
independent state isn't supported on OMAP44XX devices.
Ofcourse when MPUSS power domain transitions to OSWR along
with device off mode, it eventually hits off state since memory
contents are lost.
Hence the MPUSS off mode independent state is not attempted without
device off mode. All the necessary infrastructure code for MPUSS
off mode is in place as part of this series.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MPUSS(MPU Sub System) power domain
CSWR(Close Switch Retention) support to system wide suspend.
For MPUSS power domain to hit retention(CSWR or OSWR), both
CPU0 and CPU1 power domains need to be in OFF or DORMANT state,
since CPU power domain CSWR is not supported by hardware
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Default arch_idle() isn't good enough for OMAP4 because of aync bridge errata
and necessity of NOPs post WFI to avoid speculative prefetch aborts.
Hence Use OMAP4 custom omap_do_wfi() hook for default idle.
Later in the series, async bridge errata work-around patch updates the
omap_do_wfi() with necessary interconnects barriers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the CPU0 and CPU1 off mode support. CPUX close switch
retention (CSWR) is not supported by hardware design.
The CPUx OFF mode isn't supported on OMAP4430 ES1.0
CPUx sleep code is common for hotplug, suspend and CPUilde.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialise hardware supervised mode for all clockdomains if it's
supported. Initiate sleep transition for other clockdomains,
if they are not being used.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4430 ES1.0, Power Management features are not supported.
Avoid omap4_pm_init() on ES1.0 silicon so that we can continue
to use same kernel binary to boot on all OMAP4 silicons.
The ES1.0 boot failure with OMAP4 PM series was because of
the clockdomain initialisation code. Hardware supervised
clockdomain mode isn't functional for all clockdomains
on OMAP4430 ES1.0 silicon so avoid the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As per OMAP4430 TRM, the dynamic dependency between MPUSS -> EMIF
and MPUSS -> L4PER/L3_* and DUCATI -> L3_* clockdomains is enable
by default. Refer register CM_MPU_DYNAMICDEP description for details.
But these dynamic dependencies doesn't work as expected. The hardware
recommendation is to enable static dependencies for above clockdomains.
Without this, system locks up or randomly crashes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pm44xx.c is built only when CONFIG_PM is setup,
remove redundant CONFIG_PM check.
This also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=25022
Reported-by: Martin Etti <ettl.martin@gmx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP powerdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/powerdomain.h
to mach-omap2/powerdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access powerdomain code
and data directly.
As part of this process, remove the references to powerdomain data
from the GPIO "driver" and the OMAP PM no-op layer, both in plat-omap.
Change the DSPBridge code to point to the new location for the
powerdomain headers. The DSPBridge code should not be including the
powerdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.
The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).
Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for basic suspend doing a CPUx wfi
for OMAP4. All powerdomains are for now are kept programmed
in ON state.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
