On several Renesas ARM SoCs, the GIC is described in DT as being a
Cortex A9 GIC, while it's actually a PL390. This is not only stated in
the documentation, but has been verified by reading the GICD_IIDR
register.
To correct this:
1. Update the DT compatible value to match reality,
2. Update the board staging drivers to match the above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+GQm
-----END PGP SIGNATURE-----
Merge tag 'renesas-gic-cleanup-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Renesas ARM Based SoC GIC Cleanup for v4.5
On several Renesas ARM SoCs, the GIC is described in DT as being a
Cortex A9 GIC, while it's actually a PL390. This is not only stated in
the documentation, but has been verified by reading the GICD_IIDR
register.
To correct this:
1. Update the DT compatible value to match reality,
2. Update the board staging drivers to match the above.
* tag 'renesas-gic-cleanup-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
staging: board: armadillo800eva: Use "arm,pl390"
staging: board: kzm9d: Use "arm,pl390"
ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use SoC-specific usb-dmac and IPMMU compatibility strings
* Add internal delay for i2c IPs
* Add missing serial devices to r8a7793
* Enable DMA for r8a7793 serial devices
* Add serial port config to chosen/stdout-path
* Tidyup #sound-dai-cells settings for r8a7798/bockw
* Remove deprecated #gpio-range-cells from r8a7793
* Add EtherAVB support to r8a7791
* Add MSIOF support to sh73a0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bncx
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Third Round of Renesas ARM Based SoC DT Updates for v4.5
* Use SoC-specific usb-dmac and IPMMU compatibility strings
* Add internal delay for i2c IPs
* Add missing serial devices to r8a7793
* Enable DMA for r8a7793 serial devices
* Add serial port config to chosen/stdout-path
* Tidyup #sound-dai-cells settings for r8a7798/bockw
* Remove deprecated #gpio-range-cells from r8a7793
* Add EtherAVB support to r8a7791
* Add MSIOF support to sh73a0
* tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (25 commits)
ARM: shmobile: r8a779x: use SoC-specific usb-dmac compatibility strings
ARM: shmobile: r8a7794: IPMMU compat string SoC part number update
ARM: shmobile: r8a7793: IPMMU compat string SoC part number update
ARM: shmobile: r8a7791: IPMMU compat string SoC part number update
ARM: shmobile: r8a7790: IPMMU compat string SoC part number update
ARM: shmobile: r8a7794: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7791: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7790: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7793: Describe DMA for the serial ports
ARM: shmobile: r8a7793: Add missing serial devices to DT
ARM: shmobile: lager dts: Add serial port config to chosen/stdout-path
ARM: shmobile: porter dts: Add serial port config to chosen/stdout-path
ARM: shmobile: silk dts: Add serial port config to chosen/stdout-path
ARM: shmobile: gose dts: Add serial port config to chosen/stdout-path
ARM: shmobile: bockw dts: Update console parameters
ARM: shmobile: ape6evm dts: Add serial port config to chosen/stdout-path
ARM: shmobile: alt dts: Add serial port config to chosen/stdout-path
ARM: shmobile: koelsch dts: Add serial port config to chosen/stdout-path
ARM: shmobile: r8a7778: tidyup #sound-dai-cells settings
ARM: shmobile: bockw dts: Override #sound-dai-cells to zero
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWcnPzAAoJEFBXWFqHsHzOvfAIALZo+lVpA3c89ZuDJn0bKfsI
hsV2wfMW1N5BhLN0AGjNIk/nk/YWhZ57gZyQ8miMdz2VeQRSgcjRaFFfEGRGOGop
OrrKpgmRKmUNxMrvztLlMmb1hGxpHOO7z/CXO3UrzDRIiw9lzxYymt0Re2UHiE1u
+tekMe7xBdimfMVmcM8RX/FOZC81tUjH3W8fyPbbzTTgrAnLPmXcfjtHkXy2VPw0
5ikWCJhFWB9ODnmKHbdA7YsNh52JAe5BieWiLXzLj33XJNDBbiFBbBltbo+BJZnp
ZaIek/fGHbq7ouCSLdRq7SEQn6ZbjpHhlic/okqNX0ux29QpY2GKTbiq8fLmcLU=
=wMKP
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.4, 3rd round:
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
* tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWcThWAAoJEAf03oE53VmQuRgIAJG4qqeh62GE5naX6wCiaPmi
bWay4W1iMImiX+DHIKgFpBdHmjbHUlajUqifk4+CQ08FuFBiSl23pOP9U0j4b0Hr
jglidWJRpm2vlqN+25R/lJgwA3jleFtDn/l5EW8P5kL8WkXfXOWU7Jop+Pqxae0a
aAmKZKi9MU6mwUyZnDEYpNf29pILbBve+vPqRRVaFXiOzDYXzl3LnTE2zQvSeY0U
dpkrrH2jbjfJ8gWmAvfMqTuJLwbgv00H5MvcaP3Q8MR+7F6ATZUtqjSiMF+aRYCM
sUYCJTG4WglZvWBFTn4LcSTXZgwfVjM4r59hd18Ep2TGnXk3fRS17xTxtoAQczE=
=+zlN
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
First batch of DT changes for 4.5:
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time
ARM: at91/dt: sama5d4: update i2c compatible string
ARM: at91/dt: sama5d4 master clock can run at 200MHz now
ARM: at91/dt: sama5d2: add watchdog node
ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK
ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus
ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner device-tree related patches for the 4.5 merge window.
* Support for the H3
* Addition of the RSB to the relevant devices (sun8i, sun9i)
* Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
* Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
* Addition of the audio codec to a bunch of boards
* New board: ICNova SWAC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qu2G
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.5
Allwinner device-tree related patches for the 4.5 merge window.
* Support for the H3
* Addition of the RSB to the relevant devices (sun8i, sun9i)
* Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
* Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
* Addition of the audio codec to a bunch of boards
* New board: ICNova SWAC
* tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (40 commits)
ARM: dts: sun7i: Olimex A20-SOM-EVB: Enable mmc3 (baseboard SD socket)
ARM: dts: sun7i: Olimex A20-SOM-EVB: Add LRADC keys
ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controller
ARM: dts: sun9i: cubieboard4: Enable consumer IR receiver
ARM: dts: sun9i: cubieboard4: Enable LEDs
ARM: dts: sun7i: Add VE (Video Engine) module clock node
ARM: dts: sun4i: Add VE (Video Engine) module clock node
ARM: dts: sun8i: Add Orange Pi Plus support
ARM: dts: sunxi: Add Allwinner H3 DTSI
ARM: dts: sun7i: Add DRAM gates
ARM: dts: sun4i: Add DRAM gates
ARM: dts: sun9i: Add NMI controller device node
ARM: dts: sun9i: optimus: Enable Reduced Serial Bus controller
ARM: dts: sun9i: Add Reduced Serial Bus controller device node to A80 dtsi
ARM: dts: sun9i: optimus: Enable consumer IR receiver
ARM: dts: sun9i: Add consumer IR receiver device node and pinmux settings
ARM: dts: sun9i: optimus: Enable LED3
ARM: dts: sun9i: Add A80 R_PIO pin controller device node
ARM: dts: sun9i: Add TODO comments for the main and low power clocks
ARM: dts: sun9i: Add A80 PRCM clocks and reset control nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Various small DT changes, GPIO, slcr, cpu label
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZusi0ACgkQykllyylKDCFCDgCfQ0mCK4O38NMUHwG9wA4THD/e
54MAoJtiu6VVch3iJ7aMX7rcDPhQPQW9
=XrJB
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx into next/dt
arm: Xilinx Zynq dt patches for v4.5
- Various small DT changes, GPIO, slcr, cpu label
* tag 'zynq-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx:
ARM: dt: zynq: Add labels to cpu nodes to allow overriding OPPs.
ARM: dts: zynq: describe SLCR as simple-mfd rather than simple-bus
ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
ARM: zynq: DT: Add interrupt-controller property to GPIO
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit enables the touchscreen on TS-4800, using the ts4800-ts
driver.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds LCD support for the TS-4800. The panel is an Okaya
RS800480T-7X0WQ and the timings have been extracted from Technologic
Systems' tree.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Novena is an open-hardware laptop/desktop/bare board.
See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Previously, the device tree mapped the FPGA like any other IPs inside
the SoC, but it is actually mapped through the WEIM (Wireless External
Interface Module). This patch updates the device tree to make use of it.
About the timings: in the image provided by the manufacturer, only
CS0GCR1 is changed. The other values are the default ones, but the WEIM
bindings expect them to be all explicitly set in the device tree, so I
just put the default values in the dt.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These pins are actually not routed for UARTs, they should not be
reserved.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the device nodes for 2D, 3D and VG GPU cores.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Added sata node to ls1021aqds and ls1021atwr board to support
sata function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.
More details here:
http://wiki.embeddedarm.com/wiki/TS-4800
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Colibri standard pinmux for FlexCAN controller instances. CAN
is not a standard Colibri feature, but the datasheet predefines
pins which provide CAN (compatible across some modules). Hence,
add the pinmux on module level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No functional change, just moving the node to the place where it
belongs according to its unit address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows for consistent numbering of the IPU output and
input ports.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This has been moved to the reg property where it belongs for quite some
time. The range has been unused by the kernel since then and with kernel
4.4 it's flagged as an unparsable range, as it does not comply to the
PCI ranges DT binding. Fix this by removing the superfluous range.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audio IP need the spba clock, but original clock name "dma" is not
accurate, so change it to name "spba". The audio driver has been
using the new name "spba", the binding document has been updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As on i.MX7D, we using a virtual arm clk for CPU frequency
scaling, so correct the clocks info used by the cpufreq driver.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This addes support for SPI available on an off-board connector available on
some models of the GW52xx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via
Cortex-A5 running Linux using Stefan Agner's <stefan@agner.ch> "m4boot"
utility.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the existing Vybrid DSPI devicetree implementation to also
describe the dspi2 and dspi3 functional blocks.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This, together with the corresponding patch to pwm-imx.c, allows to order the
pwm devices correctly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl.dtsi uses compatibles "fsl,imx6q-gpt", "fsl,imx31-gpt".
imx6dl.dtsi uses compatibles "fsl,imx6dl-gpt", "fsl,imx6q-gpt" since
commit
4e415ed814 (ARM: dts: imx6dl: add imx6dl gpt specific compatible string)
If imx6dl would be compatible with imx6q-gpt it would also have to be
compatible with imx31-gpt which is currently missing.
Based on the above mentioned patch I assume imx6q-gpt and imx6dl-gpt are
not compatible. So imx6q-gpt should be removed as compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.
Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.
With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the displays supported by the Ventana boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
and HDMI DDC and is enabled by the bootloader. Set the regulator to
always-on so that Linux doesn't turn it off thinking its not needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds some values that are needed for an out-of-tree device
tree I'm currently working with.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify the 'adck-max-frequency' property in the adc nodes.
According to Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
this is a recommended property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It can improve the USB performance when choosing larger
burst size at some systems (bus size is larger), there is
no side effect if this burst size is larger than bus size.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After setting ahb burst configuration as 0, we can increase tx/rx
burst size, it will improve the USB performance
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Switch from Exynos-specific restart/poweroff handler
(mach-exynos/pmu.c) to generic syscon-reboot and syscon-poweroff
drivers.
This depends on adding syscon nodes to DTS to preserve
bisectability.
2. Minor improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JWjG
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Samsung Exynos improvements for 4.5:
1. Switch from Exynos-specific restart/poweroff handler
(mach-exynos/pmu.c) to generic syscon-reboot and syscon-poweroff
drivers.
This depends on adding syscon nodes to DTS to preserve
bisectability.
2. Minor improvements.
* tag 'samsung-soc-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: EXYNOS: Remove redundant code from regs-pmu.h
ARM: EXYNOS: Constify local exynos_pmu_data structure
ARM: EXYNOS: Switch to syscon reboot and poweroff
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/NF/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Device Tree changes adding necessary nodes for syscon reboot/poweroff
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.
* tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
The development kit uses a TSC2004 chip attached to I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file does not add support for the ft5x touchscreen found at
i2c bus 1, addr 0x38, irq PG11, because it does not work out of the box.
It seems it has been flashed with the wrong firmware and needs to have
alternative firmware uploaded at boot to make the touchscreen work
properly, when hot-booting from android into an upstream kernel the
touchscreen does work.
The Memsic MXC622X accelerometer at i2c bus 1, addr 0x15 also is not
enabled as there is no driver for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Wits Pro A20 DKT has a gbit ethernet port, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on the MK808C.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on some variants
of the MK802.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The socfpga.dtsi explicitly enabled MMC support, but not all boards are
equiped with an MMC card. There are setups which only have QSPI NOR.
Therefore, disable the MMC support on socfpga.dtsi level and enable it
on per-board basis.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patchset is the initiation version to try work
for kylin board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In general, the sdio/sdmmc is used by the wifi module
and sd card.
let's add the node for these function.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pinctrl gpio pull up/down is incorrect since the rk3036 SoCs
can't set the status in the internal.
We should keep the default status for enable the gpio status,
In fact, the pull_none is the disable the gpio pull up/down.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PA GPIO pin (PH15) controls power to external amplifier (FT2012Q).
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pov protab2-ips9 tablet uses the A10's integrated audio codec,
enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 tablet uses the A13's integrated audio codec, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add qspi memory mapped region entries for AM43xx based SoCs. Also,
update the binding documents for the controller to document this change.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add qspi memory mapped region entries for DRA7xx based SoCs. Also,
update the binding documents for the controller to document this change.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For whatever reason, this patch was not applied verbatim and had all
tabs replaced with spaces. Replace them back by a quick sed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Revert 6f0f6c40b66 ("ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo")
because it It was already done and it's just a duplicate. See:
2d11961f3e ("ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for Logic PD type 15 display for older development kits.
This uses GPIO for the backlight.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
bluetooth HW is WLS1271 chip connected to UART1.
Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.
Bluetooth enable GPIO is set to enable during startup by setting the
relevant pinmux pin to pull-up.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD.
Add I2C GPIOs configurations for DVI and LCD enable.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the PMA8084 regulators found on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds support for RPM and SMD nodes that are present on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds all the required nodes to support SMEM on APQ8084
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
GSBI6 UART module is connected to BT chip, which uses
hardware flow control lines. Enable them on SoC side.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mesm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap fixes for 81xx for v4.5 merge window" from Tony Lindgren:
Fixes for ti81xx for v4.5 merge window. We have hp t410 already booting
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
* tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=De8M
-----END PGP SIGNATURE-----
Merge tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Merge "Realview DT files" from Linus Walleij:
The device tree changes for the continued RealView DT
support.
* tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add device tree for PB11MPCore
clk: add ARM syscon ICST device tree bindings
ARM: add DT bindings for the ARM11MPCore CPU cluster
Merge "Broadcom soc changes for v4.5" from Florian Fainelli:
This pull request contains Broadcom SoC changes for 4.5, with the following changes:
- Lucas Stach removes the workaround for an imprecise fault for Broadcom
BCM5301x SoCs (Northstar) since this is now handled by the ARM/Linux kernel
directly
- Hauke Merthens enables a bunch of erratas for the Cortex-A9 and PL310 L2
cache present on early Northstar chips (BCM4708)
- Kapil Hali adds SMP support for the Northstar Plus SoCs by consolidating the
existing SMP code for Kona SoCs (mobile platforms), fixng the Device Tree
binding for the Kona platforms (wrong placement for 'enable-method' and
'secondary-reg') and then finally adds the functional code for the Northstar
Plus platforms to boot their secondary CPUs
- Jon Mason enables SMP on BCM4708/BCM5301X (Northstar SoCs) by building the generic
Northstar/Northstar Plus SMP code, and adding the relevant SMP Device Tree nodes
* tag 'arm-soc/for-4.5/soc' of http://github.com/Broadcom/stblinux:
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
ARM: BCM5310X: activate erratas needed for SoC
ARM: BCM5301X: remove workaround imprecise abort fault handler
Pull "Broadcom devicetree changes for v4.5¨ from Florian Fainelli:
This pull request contains the Broadcom ARM-based Device Tree changes for 4.5:
- Jon Mason enables the following for Broadcom Northstar Plus SoCs: PCI (using
iProc PCI), NAND flash controller (BRCMNAND), TWD Timer and Watchdog
(Cortex-A9), I2C (iProc), clock providers, does some Device Tree cleanups
(re-parenting, fixing register sizes and hierarchy)
- Jon Mason also adds support for some reference Broadcom Northstar reference
designs like the BCM5301X SVK reference boards, updates the existing binding
documentation to cover the Northstar chips: 4708, 4709 and 53012.
- Pramod Kumar adds the GPIO to pinctrl mapping for the Broadcom Northstar Plus
SoCs
- Yendapally Reddy Dhananjaya Reddy adds pinctrl Device Tree nodes for the
Broadcom Northstar Plus SoCs device tree nodes
- Ray Jui adds Cygnus PCIe PHY Device Tree nodes and enables MSI for the iProc
PCI controller on Cygnus platforms
- Kapil Hali adds SMP binding documentation and Device Tree nodes for the
Northstar Plus SoCs
- Florian Fainelli adds clock provider support for the Broadcom BCM63138 DSL
SoCs by utilizing the existing iProc ARM PLL controller, this includes a
stable topic branch from Stephen Boyd to be merged
- Rafal Milecki adds missing LEDs for the Netgear R8000 router
* tag 'arm-soc/for-4.5/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Enable MSI support for Broadcom Cygnus
ARM: dts: Add SMP support for Broadcom NSP
dt-bindings: add SMP enable-method for Broadcom NSP
ARM: dts: enable pinctrl for Broadcom NSP
ARM: dts: enable PCIe PHY support for Cygnus
ARM: dts: Cygnus: define ngpios property in gpio controller's node
ARM: BCM5301X: Add missing Netgear R8000 LEDs
ARM: dts: BCM63xx: Add ARMPLL device tree nodes
clk: bcm: Add BCM63138 clock support
clk: iproc: Extend binding to cover BCM63138
ARM: dts: enable clock support for Broadcom NSP
ARM: dts: enable clock support for BCM5301X
ARM: dts: NSP: Add I2C support to the DT
ARM: dts: NSP: Device Tree clean-ups
dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT
ARM: dts: bcm5301x: Add BCM SVK DT files
dt-bindings: Add new SoCs to bcm4708 DT bindings
ARM: dts: NSP: Add TWD Support to DT
ARM: dts: NSP: Add NAND Support to DT
ARM: dts: NSP: Add PCI support
Though the driver will continue to check for and support the legacy
"isil,irq2-can-wakeup-machine" boolean property to wakeup source,
"wakeup-source" is the new standard binding.
This patch replaces the legacy "isil,irq2-can-wakeup-machine" with the
unified "wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the GPU for SolidRun's Cubox.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add DT support for the Vivante GC600 GPU on Marvell Dove platforms.
These nodes default to being disabled unless a platform decides they
should be enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This adds a device tree for the CloudEngines PogoPlug series 4
NAS device. Inspired by out-of-tree boardfiles from ArchLinux
by Kevin Mihelich.
Cc: Moonman <moonman.ca@gmail.com>
Cc: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a new DTS file to support the Zyxel NSA325(v2) dual bay
NAS device, based on the NSA320 DTS files.
The only difference to the NSA320 device is GPIO47.
This en/disables the power for the hdd in slot2, currently
fixed to on.
[gregory.clement@free-electrons.com: fix comment format]
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Data have to be held longer for the PMIC device. The ACT8945A
datasheet claims that minimum SDA data hold time is about 300 ns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
A new compatible string has been introduced: atmel,sama5d4-i2c. It
allows to use the i2c-sda-hold-time-ns property if needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After the change of frequency a SAMA5D4 can reach, we have to modify the
maximum clock specification for the master clock, up to 200MHz now.
It avoids the wrong message saying that "master clk is overclocked" for this
configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add watchdog node to support SAMA5D4 watchdog.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system
consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip
and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port,
LEDs and expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add pinmux for the 4 remaining signals used in 8-bit MMC 0
bus configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Synchronise the comments in mmc0 pinmux node with HSMCI0 pinmux
description in the Atmel SAMA5D4 datasheet from 24-Aug-15 page
1119, section 37.6.1, Table 37-3 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'assigned-clock-parents' and 'assigned-clock-rates' list
should corresponding to the 'assigned-clocks' property clock list.
Signed-off-by: Bai Ping <b51503@freescale.com>
Fixes: ed339363de ("ARM: dts: imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9lSI
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Add I2C0 and two I2C EEPROM devices on the CIAA-NXP board:
* 24AA1025 EEPROM, 1Mbit: it is accessed as two 512Kbit EEPROMs.
* 24AA025E48 EEPROM, 2kbit.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Enable the PWM based on the State Configurable Timer (SCT) included in
the LPC4337 SoC of the CIAA-NXP board.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add Freescale MMA7455 3-axis I2C accelerometer as found on
Embedded Artists' LPC4357 Developer's Kit to the device tree.
This makes it possible to access the accelerometer through
the API provided by IIO.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add node for the NXP LPC18xx EEPROM memory which can be found in
NXP LPC185x/3x and LPC435x/3x/2x/1x devices.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This patch adds EFI stub support for the ARM Linux kernel.
The EFI stub operates similarly to the x86 and arm64 stubs: it is a
shim between the EFI firmware and the normal zImage entry point, and
sets up the environment that the zImage is expecting. This includes
optionally loading the initrd and device tree from the system partition
based on the kernel command line.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
By adding labels to the cpu nodes in the dtsi, a dts that
includes it can change the OPPs by referencing the cpu0
through the label.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SLCR (System-Level Control Registers) block is an MFD (Multi
Function Device) rather than a bus.
"simple-mfd" seems a more suitable compatible string than "simple-bus".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO can be used as interrupt-controller. Add the missing properties to
the GPIO node.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed (thanks Simon!) by reading the GICD_IIDR
register, which reports 0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed (thanks Chris, Wolfram!) by reading the
GICD_IIDR register, which reports 0x0000043b (PL390 = 0x00, ARM =
0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DT binding for the Exynos DRM Display Port (DP) driver isn't consistent
since it uses a phandle to describe the connection between the DP port and
the display panel but uses the OF graph ports and endpoints to describe the
connection betwen the DP port, a bridge chip and the panel.
The Exynos DP driver and the DT binding have been changed to allow also to
describe the DP port to panel connection using ports / endpoints (OF graph)
so this patch changes the Exynos5800 Peach Pi DT to make it consistent with
the Exynos5420 Peach Pit that has a eDP to LVDS chip and uses OF graph too.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWatW3AAoJEFBXWFqHsHzOV1UH/2g3U77HC19JcBWNmEObND81
ygLocM5cwwSDmVoFTKt7GK4fBrC/n57Pl0z2LZg1wE2Nd+jJ3GjknPrICgOnOn1Y
bYXBJW4bm9eJZC2OJhMcW1PygaQOe64+F7iptcrrodkbg62A+AGXMq+g24rNupOe
IAg87RSLkLQFxZr7B1P8dLgSCYTjRsgUHGkeGQ3CfrXckWa1m5LG2uCUD2HiPsfF
i1y4xN/Hfpj4RPV+6Hj7QoTUpK3CXqJruMPf+OkhFYhJmSRkDZdAzAAC93xVJO1w
KWc77rN7LZzaYBajamygbC3LY7ygAw5YxsJrSObyc4XPCBVdb2dVk9Se26FzWhw=
=QZJM
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lCuD
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.5 merge window" from Tony Lindgren:
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
* tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (97 commits)
ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi
ARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi
ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs
ARM: dts: am57xx: sbc-am57x: add HDMI support
ARM: dts: am57xx: compulab-sb-som: add HDMI connector
ARM: dts: am57xx: sbc-am57x: add LCD support
ARM: dts: am57xx: sbc-am57x: add GPIO expander support
ARM: dts: am57xx: sbc-am57x: add EEPROM support
ARM: dts: am57xx: sbc-am57x: add usb vbus pinmux
ARM: dts: am57xx: cl-som-am57x: add MMC1 support
ARM: dts: am57xx: sbc-am57x: add basic board support
ARM: dts: am57xx: cl-som-am57x: add analog audio support
ARM: dts: am57xx: cl-som-am57x: add touchscreen support
ARM: dts: am57xx: cl-som-am57x: add USB support
ARM: dts: am57xx: cl-som-am57x: add dual EMAC support
ARM: dts: am57xx: cl-som-am57x: add spi-flash support
ARM: dts: am57xx: cl-som-am57x: add eMMC support
ARM: dts: am57xx: cl-som-am57x: add EEPROM support
ARM: dts: am57xx: cl-som-am57x: add I2C3 support
ARM: dts: am57xx: cl-som-am57x: dts: add RTC support
...
- Fix Armada 388 GP dts
- Add clock related to PMU for Dove
- Add SolidRun Armada 388 Clearfog A1 dts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZq19wACgkQCwYYjhRyO9WXMwCeLbQllCn4X5978w54p7Iaid6H
YSsAn3WTLDW/ufY/Ge8xt+jrVh8KqwY4
=a8ky
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.5-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt for 4.5 (part 2)" from Gregory CLEMENT:
- Fix Armada 388 GP dts
- Add clock related to PMU for Dove
- Add SolidRun Armada 388 Clearfog A1 dts
* tag 'mvebu-dt-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT file
dt-bindings: add Marvell PMU documentation
ARM: dts: dove: add Dove divider clocks
dt-bindings: add Marvell core PLL and clock divider PMU documentation
ARM: mvebu: remove duplicated regulator definition in Armada 388 GP
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWYetUAAoJEPOmecmc0R2B4goIAIiVjdbuetKLxeEqDWmEdCnI
AKlV+IM1CWt8ib2k5bCoaYmWwtujY6m/2oHhbJklHgv3+K32lltwgZMJPeJu7xi3
C02HCdq6DydsCb2154giKOXj+SMsNZ/c38Gk1sDFFPQCcwfgT9Hg+7HOXCim2Ac8
C/Ewi7z6bZKzkvwy28KrQVPDub2DB/JQAGp8DP9hfK9k23PtaQRoLhTExj68O6JK
rRjB67hb1+xdKgf8ujXevIYvoacO1odW4fLnB7KC4ei/O2XycKK/4ohzrENe/zJ6
Y2wYnb1YGiLtjgx0DlpbPvaCE6/UyX+ZhVC4kUiB937/x1ZpCZX9ttLMT91gKx8=
=F0Xt
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "rockchip dts32 changes for 4.5" from Heiko Stuebner:
First round of arm devicetree changes.
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.
* tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add gpio-ir-receiver to the R89 board
ARM: dts: rockchip: add touchscreen node to veyron minnie
ARM: dts: rockchip: add veyron-mickey board
ARM: dts: rockchip: add veyron-brain board
ARM: dts: rockchip: make sure edp_24m is associated to xin24m on veyron
ARM: dts: rockchip: override thermal settings on veyron-speedy
ARM: dts: rockchip: update the thermal management on rk3288
ARM: dts: rockchip: Add Crypto node for rk3288
ARM: dts: rockchip: add rk3036-evb board
ARM: dts: rockchip: add core rk3036 dtsi
clk: rockchip: add dt-binding header for rk3036
clk: rockchip: add an id for rk3288 crypto clk
ARM: dts: rockchip: Add IR receiver to RK3288 Radxa Rock 2 Square
ARM: dts: rockchip: add channels properties for i2s
ARM: dts: rockchip: set system-power-controller property on rk3288-rock2
ARM: dts: rockchip: Setup rk3066/rk3188 ethernet0 alias for u-boot
ARM: dts: rockchip: Setup rk3288 ethernet0 alias for u-boot
UniPhier SoCs (except PH1-sLD3) have several nodes in common.
Factor out them into uniphier-common32.dtsi. This improves the code
maintainability.
PH1-sLD3 is so old that it has more or less different register maps
than the others. So, it cannot be included in this refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The UART3 is assigned with IRQ 29 for old SoCs, IRQ 177 for new ones,
and PH1-Pro4 is on the boundary.
PH1-sLD3: UART3 is unavailable
PH1-LD4, PH1-sLD8: only IRQ 29 is supported
PH1-Pro4: both IRQ 29 and 177 are supported
PH1-Pro5, ProXstream2, PH1-LD6b: only IRQ 177 is supported
This SoC can choose either IRQ 29 or IRQ 177, but the former is shared
with another hardware (low speed serial0). The latter is dedicated
for this hardware and more recommended.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SQuE
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500" from Linus Walleij:
- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure the sensors on the TVK board correctly
ARM: u300: remove regulator-compatible usage
ARM: ux500: remove regulator-compatible usage
ARM: ux500: replace legacy *,wakeup property with wakeup-source
ARM: ux500: Assign proper sensor IRQs for Snowball
ARM: ux500: push down Rohm TS to STUIB
The card detect pin is currently called sdmcc-cd.
This patch fixes the typo and renames the pin to sdmmc-cd.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In general, the logic voltage is affected by ddr frequency factors.
We should fix the correct voltage range since assuemd that we have the
ddr frequency driver in mainline in the future.
AFAIK, the 1.8v voltage is used by the SD3.0 card.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rk3288-evb-act8846 and rk3288-evb-rk808 are the power boards of
rk3288-evb, they provide the same power supply interface to the
motherboard. Sort out them, put the public part to rk3288-evb.dtsi,
such as gmac and cpu-supply, leaving only the power section.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
