We already relocated hisi_sas_get_ncq_tag() into common file main.c,
so delete get_ncq_tag_v3_hw() and use hisi_sas_get_ncq_tag() instead.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The latest MegaRAID Firmware (for Invader series) has support for 64bit
DMA for both streaming and consistent DMA buffers. All Ventura series
controller FW always support 64 bit consistent DMA. Also, on a few
architectures 32bit DMA is not supported.
Current driver always prefers 32bit for consistent DMA and 64bit for
streaming DMA. This behavior was unintentional and carried forwarded
from legacy controller FW. Need to enhance the driver to support 64bit
consistent DMA buffers based on the firmware capability.
Below is the DMA setting strategy in driver with this patch. For
Ventura series, always try to set 64bit DMA mask. If it fails fall back
to 32bit DMA mask. For Invader series and earlier generation
controllers, first try to set to 32bit consistent DMA mask irrespective
of FW capability. This is needed to ensure firmware downgrades do not
break. If 32bit DMA setting fails, check FW capability and try seting to
64bit DMA mask.
There are certain restrictions in the hardware for having all sense
buffers and all reply descriptors to be in the same 4GB memory region.
This limitation is h/w dependent and can not be changed in firmware.
This limitation needs to be taken care in driver while allocating the
buffers. There was a discussion regarding this - find details at below
link. https://www.spinics.net/lists/linux-scsi/msg108251.html
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver load fails if memory allocation for request frame pool fails due
to the higher queue_depth requirement. The driver now allows dynamically
reducing queue_depth if memory allocations fail rather than failing
load. With this, there is no need to limit queue_depth to 1K.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain cases, the host memory is limited and with FW supporting
higher queue depths there are increasing chances of IO request frame
allocation failures that we are seeing. In case of request frame
allocation failures, retry allocation with reduced queue depth (in steps
of 64) to continue to configure the controller with a reduced
performance rather than failing load.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd->frame->dcmd.opcode will be valid only for MFI_CMD_DCMD
IOCTL frames. Currently driver check for cmd->frame->dcmd.opcode without
checking cmd type. Ensure we check dcmd opcode only for MFI_CMD_DCMD
commands. Separate handling of MFI_CMD_SMP/STP commands from
MFI_CMD_DCMD in completion path.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Older firmware version unconditionally pulls 4k frame for IOC INIT MFA
frame. But driver allocates 1k or 4k max_chain_frame_sz based on FW
capability. During boot time, this results in DMA read errors.
Workaround fix in driver by allocating separate ioc_init frame of 4k
size to support older firmware.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver needs to send current host time to firmware during init.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring, no functional change. Create new function to
initialize all the controller parameters during load time.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-use the pre-allocated ctrl_info DMA buffer.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pre-allocate few of the frequently used DMA buffers during load time.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code refactoring - create separate functions to allocate and free
controller DMA buffers
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code refactoring to improve readability. Move the
code to allocate and free controller memory into separate functions.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fusion_context structure is very large around 180kB and most of the size
is contributed by log_to_span array. Move log_to_span out of fusion
context and have separate allocation for log_to_span. And use kmalloc to
allocate fusion_context. Currently kmemleak reports 1000s of false
positives for fusion->cmd_list[]. kmemleak does not track page
allocation for fusion_context. This change will also fix the false
positives reported by kmemleak.
Ref: https://marc.info/?l=linux-scsi&m=150545293900917
Reported-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increase code readability. No functional change.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for PCI VID/DID 0x1000/0x0015 based MegaRAID controllers.
Since the DID 0x0015 conflicts with DELL PERC5 controllers,
add vendor ID based check specific for DELL PERC5.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Refactor adapter_type to set for all generation controllers, not
just for fusion controllers.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for enclosure logical identifier
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suggested-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Preserve external device queue depth during a scan operation.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct re-enabling ioaccel after:
1) RAID transformations and
2) multi-path fail-overs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are times when the DEFAULT_TIMEOUT (30 seconds) is not enough.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a corner case where newly created volumes are not detected
automatically on an external RAID controller that has no configured
volumes during initial device discovery.
The fix is to set the discovery_polling flag when an external RAID
controller is detected. This causes a device rescan every 20-30 seconds,
so that newly created volumes will be detected automatically.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tell hpsa controller to generate a checkpoint for rare lockup
conditions.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clean up stale information.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I am resubmitting this patch on behalf of Martin Wilck with his
permission.
The original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102083.html
This patch did not help until Hannes's
commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.
--------------------------------------
Original patch description from Martin:
--------------------------------------
When the hpsa module is unloaded using rmmod, dangling
symlinks remain under /sys/class/sas_phy. Fix this by
calling sas_phy_delete() rather than sas_phy_free (which,
according to comments, should not be called for PHYs that
have been set up successfully, anyway).
Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleans up a lot of warnings when unloading the driver.
A current example of the stack trace starts with:
[ 142.570715] sysfs group 'power' not found for kobject 'port-5:0'
There can be hundreds of these messages during a driver unload.
I am resubmitting this patch on behalf of Martin Wilck with his
permission.
His original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102085.html
This patch did not help until Hannes's
commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.
---------------------------
Original patch description:
---------------------------
Unloading the hpsa driver causes warnings
[ 1063.793652] WARNING: CPU: 1 PID: 4850 at ../fs/sysfs/group.c:237 device_del+0x54/0x240()
[ 1063.793659] sysfs group ffffffff81cf21a0 not found for kobject 'port-2:0'
with two different stacks:
1)
[ 1063.793774] [<ffffffff81448af4>] device_del+0x54/0x240
[ 1063.793780] [<ffffffff8145178a>] transport_remove_classdev+0x4a/0x60
[ 1063.793784] [<ffffffff81451216>] attribute_container_device_trigger+0xa6/0xb0
[ 1063.793802] [<ffffffffa0105d46>] sas_port_delete+0x126/0x160 [scsi_transport_sas]
[ 1063.793819] [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]
2)
[ 1063.797103] [<ffffffff81448af4>] device_del+0x54/0x240
[ 1063.797118] [<ffffffffa0105d4e>] sas_port_delete+0x12e/0x160 [scsi_transport_sas]
[ 1063.797134] [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]
This is caused by the fact that host device hostX is deleted before the
SAS transport devices hostX/port-a:b.
This patch fixes this by reverting the order of device deletions.
Tested-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin Wilck <mwilck@suse.de>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct spelling error.
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ever since it became possible to compile the SCSI core code as a module,
the documentation describing the module parameters has been incorrect.
Update the documentation to add a "scsi_mod." prefix to the relevant
options.
Reported-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Corrected the value defined for LINKRATE_60 (6 Gig).
Signed-off-by: Raj Dinesh <Raj.Dinesh@microsemi.com>
Signed-off-by: Viswas G <viswas.g@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when there's an error in 'ncq mode' the host has to read the ncq error
log (10h) to clear the error state. however, the ccb that is setup for
doing this doesn't setup the ccb so that the previous state is
cleared. if the ccb was previously used for an IO n_elems is set and
pm8001_ccb_task_free() treats this as the signal to go free a
scatter-gather list (that's already been freed).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified SATA abort handling with following steps:
1) Set device state as recovery.
2) Send phy reset.
3) Wait for reset completion.
4) After successful reset, abort all IO's to the device.
5) After aborting all IO's to device, set device state as operational.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added port reset timer value as 2000ms for PM8006 sata controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tag is taken from the tag pool instead of using the hardcoded tag
value(1).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different SAS addresses are assigned for each set of phys.
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to read ILA version and inactive firmware version from MPI
configuration table and export through sysfs.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_identify structure defined by pm80xx doesn't have CRC field. So
added a new sas_identify structure without CRC.
Signed-off-by: Raj Dinesh <Raj.Dinesh@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As per SAM there is a status precedence, with any sense code 29/XX
taking second place just after an ACA ACTIVE status. Additionally, each
target might prefer to not queue any unit attention conditions, but just
report one. Due to the above, this will be that one with the highest
precedence. This results in the sense code 29/XX effectively
overwriting any other unit attention. Hence we should report the
power-on reset to userland so that it can take appropriate action.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hitachi USP-V returns 'ILLEGAL FUNCTION' when the internal staging
mechanism encountered an error. These errors should not be retried on
another path.
[mkp: s/invalid/illegal/]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All EMC SYMMETRIX support REPORT_LUNS, even if configured to report
SCSI-2 for whatever reason.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
HITACHI is always supporting VPD pages, even though it's claiming to
support SCSI Revision 3 only.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The AIX VDASD devices do support VPD pages, but implement only SPC. So
set BLIST_TRY_VPD_PAGES to correctly display the VPD information in
sysfs.
[mkp: typo]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
/sys/class/scsi_disk/0:2:0:0/manage_start_stop can be changed to 0
unexpectly by writing an invalid string.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
