Recreate the chap data list during the get chap operation in
qla4xxx_get_chap_list().
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add local_ipaddr param and support get/set operations on it.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This attribute specifies the local IP address used to establish connection.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR
interface. This command provides various tests for validating hardware
functionality.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Patch includes changes to upgrade bfa driver version to 3.2.23.0 and use
firmware version 3.2.3.0
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As per the FCP specs, the timeout for issuing ABTS is 20 sec; not 21
sec. Hence setting the TOV to 20 sec.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Observed Auto mode in the HBA side while doing manual D-Port test on the
switch side. Mode is not passed to BFA from firmware when the test is
triggered by switch side. BFA just blindly using Auto mode.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch set fixes the issue of brocade management utility hang
(bcu/HCM) when faa attributes are queried from multiple application
threads. Hang was due to race between the threads and completion handler
corruption.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In direct attach mode, if port features like QoS/Trunk/FEC/CR are
enabled, driver can receive PLOGI from the target before firmware
notifies lport online to the driver. In case the lport is not yet online
and a PLOGI is received, send a reject to the peer port, instead of
dropping it on the floor.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch addresses the issue of port not being registered with SCSI
layer on bfa or firmware initialization failure and subsequently failure
in collecting driver traces for debugging port init failures. Also it
has minor changes related to bfad state machine clean up.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch includes change to enable firmware patch simplication
feature. This feature is targeted to address the requirement to have
independent patch release for firmware. Prior to 3.2.3, releasing a
patch fix for firmware requires changes to bfa, to use new firmware
images. But with these changes, if the new firmware is flashed on to the
HBA with brocade adapter management utilites, driver uses the new
firmware after checking the patch release byte in the firmware version.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There are two memory leaks in cases 'ISCSI_NET_PARAM_VLAN_ID' and
'ISCSI_NET_PARAM_VLAN_PRIORITY' and also a potential junk pointer free if
mgmt_get_if_info() returns error because if_info will be unset and it is stack
allocated.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Cc: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
do_div() is meant for divisions of 64-bit number by 32-bit numbers.
Passing 64-bit divisor types caused issues in the past on 32-bit platforms,
cfr. commit ea077b1b96 ("m68k: Truncate base
in do_div()").
As scsi_device.sector_size is unsigned (int), factor should be unsigned
int, too.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On lpfc_debugfs_initialize function the dumpHostSlim member setup happens
when 'phba->sli_rev < LPFC_SLI_REV4' is true, however when it is false NULL
has been assigned to debug_dumpHBASlim instead of debug_dumpHostSlim.
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The assumption that sizeof(long) >= sizeof(resource_size_t) can lead to
truncation of the PCI resource address, meaning this driver didn't work
on 32-bit systems with 64-bit PCI adressing ranges.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The documentation has gone out-of-sync, so update it to
the current status.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The former minimum valid value of 'eh_deadline' is 1s, which means
the earliest occasion to shorten EH is 1 second later since a
command is failed or timed out. But if we want to skip EH steps
ASAP, we have to wait until the first EH step is finished. If the
duration of the first EH step is long, this waiting time is
excruciating. So, it is necessary to accept 0 as the minimum valid
value for 'eh_deadline'.
According to my test, with Hannes' patchset 'New EH command timeout
handler' as well, the minimum IO time is improved from 73s
(eh_deadline = 1) to 43s(eh_deadline = 0) when commands are timed
out by disabling RSCN and target port.
Signed-off-by: Ren Mingxin <renmx@cn.fujitsu.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
32bit accesses are guaranteed to be atomic, so we can remove
the spinlock when checking for eh_deadline. We only need to
make sure to catch any updates which might happened during
the call to time_before(); if so we just recheck with the
correct value.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a command runs into a timeout we need to send an 'ABORT TASK'
TMF. This is typically done by the 'eh_abort_handler' LLDD callback.
Conceptually, however, this function is a normal SCSI command, so
there is no need to enter the error handler.
This patch implements a new scsi_abort_command() function which
invokes an asynchronous function scsi_eh_abort_handler() to
abort the commands via the usual 'eh_abort_handler'.
If abort succeeds the command is either retried or terminated,
depending on the number of allowed retries. However, 'eh_eflags'
records the abort, so if the retry would fail again the
command is pushed onto the error handler without trying to
abort it (again); it'll be cleared up from SCSI EH.
[hare: smatch detected stray switch fixed]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 18a4d0a22e
(Handle disk devices which can not process medium access commands)
was introduced to offline any device which cannot process medium
access commands.
However, commit 3eef6257de
(Reduce error recovery time by reducing use of TURs) reduced
the number of TURs by sending it only on the first failing
command, which might or might not be a medium access command.
So in combination this results in an erratic device offlining
during EH; if the command where the TUR was sent upon happens
to be a medium access command the device will be set offline,
if not everything proceeds as normal.
This patch moves the check to the final test, eliminating
this problem.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
After getting warnings in an allyesconfig build[1] from this
driver, I decided to remind myself just how old it was, and
whether it warranted fixing. In the Kconfig help text, I found:
"This driver will eventually be phased out entirely"
Going back to the history archive, I see the line was added[2]
in Feb 2002, when we moved from v2.4.2.1 ---> v2.4.2.2
So, with over a decade of notification, and multiple major releases
since then, I think we can justify removing this. Currently we have
people wasting time building it during routine testing, and then
wasting more time re-researching the known reported warnings, only to
find that nobody really is willing to integrate the fixes[3] for it.
A quick search didn't seem to indicate any active user base for it.
If someone happens to have a quirky _old_ card that the eleven year
old "new" driver doesn't work with, then it is entirely reasonable
that they stick with a kernel version that predates this removal.
[1] drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_register’:
drivers/scsi/aic7xxx_old.c:7901:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch]
drivers/scsi/aic7xxx_old.c:7898:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch]
drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_load_seeprom’:
drivers/scsi/aic7xxx_old.c:8517:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch]
drivers/scsi/aic7xxx_old.c:8510:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch]
[2] http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git commit 44e8778c
[3] https://lkml.org/lkml/2012/10/29/215
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
update sg MAINTAINERS file entry: web site and documentation
entry
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the execute firmware command fails we do not stop the rest of the
initialization process which will continue to fail so if we encounter an error
simply short circuit the process.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
