[ Upstream commit 007773e16a ]
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c52c91bb9a ]
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a841e2853e ]
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7251953d78 ]
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f106904968 ]
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c7315c9fc ]
LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9cd34efbd3 upstream.
Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.
In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).
For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
+-+-+-+-+-+-+-+-+
| | | | | |*|*|*|
+-+-+-+-+-+-+-+-+
In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
+-+-+-+-+-+-+-+-+
|*|*|*|*|*| | | |
+-+-+-+-+-+-+-+-+
This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.
And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.
Fixes: 37ffab8170 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca59d5a516 upstream.
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63aa6a6925 upstream.
Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.
But as platform_get_irq() can be used instead and is generic, use it.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes: 3194d2533e ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61acd19f9c ]
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407f ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada9e3fcc1 ]
This patch reverts commit 6e0a32d6f3 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd876 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd050abeba ]
The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04358e40ba ]
The driver misses calling clk_unprepare in probe failure and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191115083122.12278-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eb263ef08 ]
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9a8ba9769 ]
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1403cfa69d ]
The SPI_LOOP is set in spi->mode but not propagated to the register.
A previous patch removed the bit during a cleanup.
Fixes: e1bc204894 ("spi: dw: fix potential variable assignment error")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Link: https://lore.kernel.org/r/1572985330-5525-1-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a725272bda ]
The driver forgets to disable and unprepare clk when probe fails and
remove.
Add the calls to fix the problem.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
Link: https://lore.kernel.org/r/20191101121745.13413-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91ea1d7060 ]
When rebooting the system, we should lock the watchdog after
configuration to make sure the watchdog can reboot the system
successfully.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/7b04711127434555e3a1a86bc6be99860cd86668.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3b0ffa1d7 ]
In spi_gpio_probe an SPI master is allocated via spi_alloc_master, but
this controller should be released if devm_add_action_or_reset fails,
otherwise memory leaks. In order to avoid leak spi_contriller_put must
be called in case of failure for devm_add_action_or_reset.
Fixes: 8b797490b4 ("spi: gpio: Make sure spi_master_put() is called in every error path")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190930205241.5483-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f918a728c ]
This change is necessary for spidev devices (e.g. /dev/spidev3.0) working
in the slave mode (like NXP's dspi driver for Vybrid SoC).
When SPI HW works in this mode - the master is responsible for providing
CS and CLK signals. However, when some fault happens - like for example
distortion on SPI lines - the SPI Linux driver needs a chance to recover
from this abnormal situation and prepare itself for next (correct)
transmission.
This change doesn't pose any threat on drivers working in master mode as
spi_slave_abort() function checks if SPI slave mode is supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20190924110547.14770-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190925091143.15468-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 15f794bd97 upstream.
Even if the flag use_gpio_descriptors is set, it is possible that
cs_gpiods was not allocated, which leads to a kernel crash.
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191024141309.22434-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e5ec1db8b upstream.
When improving the CS GPIO support at core level, the SPI_CS_HIGH
has been enabled for all the CS lines used for a given SPI controller.
However, the SPI framework allows to have on the same controller native
CS and GPIO CS. The native CS may not support the SPI_CS_HIGH, so they
should not be setup automatically.
With this patch the setting is done only for the CS that will use a
GPIO as CS
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018152929.3287-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cbb16b212 upstream.
Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.
So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.
When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.
This patch fixes the test to match the hardware capabilities.
Fixes: 4820303480 ("spi: atmel: add support for the internal chip-select of the spi controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6910679e1 upstream.
Later versions of the QSPI controller (e.g. in i.MX6UL/ULL and i.MX7)
seem to have an additional TDH setting in the FLSHCR register, that
needs to be set in accordance with the access mode that is used (DDR
or SDR).
Previous bootstages such as BootROM or bootloader might have used the
DDR mode to access the flash. As we currently only use SDR mode, we
need to make sure the TDH bits are cleared upon initialization.
Fixes: 84d043185d ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20191007071933.26786-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_TX flag.
When performing an RX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer which is copied to the TX FIFO.
The dummy buffer is necessary because the chip is not capable of
automatically clocking out null bytes.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which fills the TX FIFO by cyclically copying
from the zero page. The transaction requires very little CPU time to
submit and generates no interrupts while running. Specifics are
provided in kerneldoc comments.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/f45920af18dbf06e34129bbc406f53dc9c5d1075.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_RX flag.
When performing a TX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer into which the RX FIFO contents are
copied. The dummy buffer is necessary because the chip is not capable
of disabling the receiver or automatically throwing away received data.
Not reading the RX FIFO isn't an option either since transmission is
halted once it's full.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which cyclically clears the RX FIFO. The
transaction requires very little CPU time to submit and generates no
interrupts while running. Specifics are provided in kerneldoc comments.
With a ks8851 Ethernet chip attached to the SPI controller, I am seeing
a 30 us reduction in ping time with this commit (1.819 ms vs. 1.849 ms,
average of 100,000 packets) as well as a 2% reduction in CPU time
(75:08 vs. 76:39 for transmission of 5 GByte over the SPI bus).
The commit uses the TX DMA interrupt to signal completion of a transfer.
This interrupt is raised once all bytes have been written to the
TX FIFO and it is then necessary to busy-wait for the TX FIFO to become
empty before the transfer can be finalized. As an alternative approach,
I have explored using the SPI controller's DONE interrupt to detect
completion. This interrupt is signaled when the TX FIFO becomes empty,
avoiding the need to busy-wait. However latency deteriorates compared
to the present commit and surprisingly, CPU time is slightly higher as
well:
It turns out that in 45% of the cases, no busy-waiting is needed at all
and in 76% of the cases, less than 10 busy-wait iterations are
sufficient for the TX FIFO to drain. This was measured on an RT kernel.
On a vanilla kernel, wakeup latency is worse and thus fewer iterations
are needed. The measurements were made with an SPI clock of 20 MHz,
they may differ slightly for slower or faster clock speeds.
Previously we always used the RX DMA interrupt to signal completion of a
transfer. Using the TX DMA interrupt now introduces a race condition:
TX DMA is always started before RX DMA so that bytes are already clocked
out while RX DMA is still being set up. But if a TX-only transfer is
very short, then the TX DMA interrupt may occur before RX DMA is set up.
If the interrupt happens to occur on the same CPU, setup of RX DMA may
even be delayed until after the interrupt was handled.
I've solved this by having the TX DMA callback clear the RX FIFO while
busy-waiting for the TX FIFO to drain, thus avoiding a dependency on
setup of RX DMA. Additionally, I am using a lock-free mechanism with
two flags, tx_dma_active and rx_dma_active plus memory barriers to
terminate RX DMA either by the TX DMA callback or immediately after
setting it up, whichever wins the race. I've explored an alternative
approach which temporarily disables the TX DMA callback until RX DMA
has been set up (using tasklet_disable(), local_bh_disable() or
local_irq_save()), but the performance was minimally worse.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/874949385f28251e2dcaa9494e39a27b50e9f9e4.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver needs to set up the clock polarity in its
->prepare_message() hook before spi_transfer_one_message() asserts chip
select to avoid a gratuitous clock signal edge (cf. commit acace73df2
("spi: bcm2835: set up spi-mode before asserting cs-gpio")).
Precalculate the CS register value (which selects the clock polarity)
once in ->setup() and use that cached value in ->prepare_message() and
->transfer_one(). This avoids one MMIO read per message and one per
transfer, yielding a small latency improvement. Additionally, a
forthcoming commit will use the precalculated value to derive the
register value for clearing the RX FIFO, which will eliminate the need
for an RX dummy buffer when performing TX-only DMA transfers.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/d17c1d7fcdc97fffa961b8737cfd80eeb14f9416.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
__spi_alloc_controller() uses a single allocation to accommodate struct
spi_controller and the driver-private data, but places the latter behind
the former. This order does not guarantee cacheline alignment of the
driver-private data. (It does guarantee cacheline alignment of struct
spi_controller but the structure doesn't make any use of that property.)
Round up struct spi_controller to cacheline size. A forthcoming commit
leverages this to grant DMA access to driver-private data of the BCM2835
SPI master.
An alternative, less economical approach would be to use two allocations.
A third approach consists of reversing the order to conserve memory.
But Mark Brown is concerned that it may result in a performance penalty
on architectures that don't like unaligned accesses.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/01625b9b26b93417fb09d2c15ad02dfe9cdbbbe5.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver uses a flag to keep track of whether a DMA
transfer is in progress.
The flag is used to avoid terminating DMA channels multiple times if a
transfer finishes orderly while simultaneously the SPI core invokes the
->handle_err() callback because the transfer took too long. However
terminating DMA channels multiple times is perfectly fine, so the flag
is unnecessary for this particular purpose.
The flag is also used to avoid invoking bcm2835_spi_undo_prologue()
multiple times under this race condition. However multiple *concurrent*
invocations can no longer happen since commit 2527704d84 ("spi:
bcm2835: Synchronize with callback on DMA termination") because the
->handle_err() callback now uses the _sync() variant when terminating
DMA channels.
The only raison d'être of the flag is therefore that
bcm2835_spi_undo_prologue() cannot cope with multiple *sequential*
invocations. Achieve that by setting tx_prologue to 0 at the end of
the function. Subsequent invocations thus become no-ops.
With that, the dma_pending flag becomes unnecessary, so drop it.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/062b03b7f86af77a13ce0ec3b22e0bdbfcfba10d.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 3bd7f6589f ("spi: bcm2835: Overcome sglist entry length
limitation") amended the BCM2835 SPI driver with support for DMA
transfers whose buffers are not aligned to 4 bytes and require more than
one sglist entry.
When testing this feature with upcoming commits to speed up TX-only and
RX-only transfers, I noticed that SPI transmission sometimes breaks.
A function introduced by the commit, bcm2835_spi_transfer_prologue(),
performs one or two PIO transmissions as a prologue to the actual DMA
transmission. It turns out that the breakage goes away if the DONE bit
in the CS register is set when ending such a PIO transmission.
The DONE bit signifies emptiness of the TX FIFO. According to the spec,
the bit is of type RO, so writing it should never have any effect.
Perhaps the spec is wrong and the bit is actually of type RW1C.
E.g. the I2C controller on the BCM2835 does have an RW1C DONE bit which
needs to be cleared by the driver. Another, possibly more likely
explanation is that it's a hardware erratum since the issue does not
occur consistently.
Either way, amend bcm2835_spi_transfer_prologue() to always write the
DONE bit.
Usually a transmission is ended by bcm2835_spi_reset_hw(). If the
transmission was successful, the TX FIFO is empty and thus the DONE bit
is set when bcm2835_spi_reset_hw() reads the CS register. The bit is
then written back to the register, so we happen to do the right thing.
However if DONE is not set, e.g. because transmission is aborted with
a non-empty TX FIFO, the bit won't be written by bcm2835_spi_reset_hw()
and it seems possible that transmission might subsequently break. To be
on the safe side, likewise amend bcm2835_spi_reset_hw() to always write
the bit.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/edb004dff4af6106f6bfcb89e1a96391e96eb857.1564825752.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify this function implementation by using a known function.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b2dd074a-1693-3aea-42b4-da1f5ec155c4@web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This helps a bit with line fitting now (the list_first_entry call) as
well as during the next patch which needs to iterate through all
transfers of ctlr->cur_msg so it timestamps them.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-npcm-fiu.c: In function npcm_fiu_read:
drivers/spi/spi-npcm-fiu.c:472:9: warning:
variable retlen set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190905072436.23932-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-37-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-36-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-35-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-34-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-33-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-32-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-31-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-30-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Michael Walle