commit f85086f95f upstream.
In register_mem_sect_under_node() the system_state's value is checked to
detect whether the call is made during boot time or during an hot-plug
operation. Unfortunately, that check against SYSTEM_BOOTING is wrong
because regular memory is registered at SYSTEM_SCHEDULING state. In
addition, memory hot-plug operation can be triggered at this system
state by the ACPI [1]. So checking against the system state is not
enough.
The consequence is that on system with interleaved node's ranges like this:
Early memory node ranges
node 1: [mem 0x0000000000000000-0x000000011fffffff]
node 2: [mem 0x0000000120000000-0x000000014fffffff]
node 1: [mem 0x0000000150000000-0x00000001ffffffff]
node 0: [mem 0x0000000200000000-0x000000048fffffff]
node 2: [mem 0x0000000490000000-0x00000007ffffffff]
This can be seen on PowerPC LPAR after multiple memory hot-plug and
hot-unplug operations are done. At the next reboot the node's memory
ranges can be interleaved and since the call to link_mem_sections() is
made in topology_init() while the system is in the SYSTEM_SCHEDULING
state, the node's id is not checked, and the sections registered to
multiple nodes:
$ ls -l /sys/devices/system/memory/memory21/node*
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
In that case, the system is able to boot but if later one of theses
memory blocks is hot-unplugged and then hot-plugged, the sysfs
inconsistency is detected and this is triggering a BUG_ON():
kernel BUG at /Users/laurent/src/linux-ppc/mm/memory_hotplug.c:1084!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp pseries_rng rng_core vmx_crypto gf128mul binfmt_misc ip_tables x_tables xfs libcrc32c crc32c_vpmsum autofs4
CPU: 8 PID: 10256 Comm: drmgr Not tainted 5.9.0-rc1+ #25
Call Trace:
add_memory_resource+0x23c/0x340 (unreliable)
__add_memory+0x5c/0xf0
dlpar_add_lmb+0x1b4/0x500
dlpar_memory+0x1f8/0xb80
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
vfs_write+0xe8/0x290
ksys_write+0xdc/0x130
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
This patch addresses the root cause by not relying on the system_state
value to detect whether the call is due to a hot-plug operation. An
extra parameter is added to link_mem_sections() detailing whether the
operation is due to a hot-plug operation.
[1] According to Oscar Salvador, using this qemu command line, ACPI
memory hotplug operations are raised at SYSTEM_SCHEDULING state:
$QEMU -enable-kvm -machine pc -smp 4,sockets=4,cores=1,threads=1 -cpu host -monitor pty \
-m size=$MEM,slots=255,maxmem=4294967296k \
-numa node,nodeid=0,cpus=0-3,mem=512 -numa node,nodeid=1,mem=512 \
-object memory-backend-ram,id=memdimm0,size=134217728 -device pc-dimm,node=0,memdev=memdimm0,id=dimm0,slot=0 \
-object memory-backend-ram,id=memdimm1,size=134217728 -device pc-dimm,node=0,memdev=memdimm1,id=dimm1,slot=1 \
-object memory-backend-ram,id=memdimm2,size=134217728 -device pc-dimm,node=0,memdev=memdimm2,id=dimm2,slot=2 \
-object memory-backend-ram,id=memdimm3,size=134217728 -device pc-dimm,node=0,memdev=memdimm3,id=dimm3,slot=3 \
-object memory-backend-ram,id=memdimm4,size=134217728 -device pc-dimm,node=1,memdev=memdimm4,id=dimm4,slot=4 \
-object memory-backend-ram,id=memdimm5,size=134217728 -device pc-dimm,node=1,memdev=memdimm5,id=dimm5,slot=5 \
-object memory-backend-ram,id=memdimm6,size=134217728 -device pc-dimm,node=1,memdev=memdimm6,id=dimm6,slot=6 \
Fixes: 4fbce63391 ("mm/memory_hotplug.c: make register_mem_sect_under_node() a callback of walk_memory_range()")
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200915094143.79181-3-ldufour@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d0da8335 upstream.
Patch series "mm: fix memory to node bad links in sysfs", v3.
Sometimes, firmware may expose interleaved memory layout like this:
Early memory node ranges
node 1: [mem 0x0000000000000000-0x000000011fffffff]
node 2: [mem 0x0000000120000000-0x000000014fffffff]
node 1: [mem 0x0000000150000000-0x00000001ffffffff]
node 0: [mem 0x0000000200000000-0x000000048fffffff]
node 2: [mem 0x0000000490000000-0x00000007ffffffff]
In that case, we can see memory blocks assigned to multiple nodes in
sysfs:
$ ls -l /sys/devices/system/memory/memory21
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
-rw-r--r-- 1 root root 65536 Aug 24 05:27 online
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_device
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_index
drwxr-xr-x 2 root root 0 Aug 24 05:27 power
-r--r--r-- 1 root root 65536 Aug 24 05:27 removable
-rw-r--r-- 1 root root 65536 Aug 24 05:27 state
lrwxrwxrwx 1 root root 0 Aug 24 05:25 subsystem -> ../../../../bus/memory
-rw-r--r-- 1 root root 65536 Aug 24 05:25 uevent
-r--r--r-- 1 root root 65536 Aug 24 05:27 valid_zones
The same applies in the node's directory with a memory21 link in both
the node1 and node2's directory.
This is wrong but doesn't prevent the system to run. However when
later, one of these memory blocks is hot-unplugged and then hot-plugged,
the system is detecting an inconsistency in the sysfs layout and a
BUG_ON() is raised:
kernel BUG at /Users/laurent/src/linux-ppc/mm/memory_hotplug.c:1084!
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp pseries_rng rng_core vmx_crypto gf128mul binfmt_misc ip_tables x_tables xfs libcrc32c crc32c_vpmsum autofs4
CPU: 8 PID: 10256 Comm: drmgr Not tainted 5.9.0-rc1+ #25
Call Trace:
add_memory_resource+0x23c/0x340 (unreliable)
__add_memory+0x5c/0xf0
dlpar_add_lmb+0x1b4/0x500
dlpar_memory+0x1f8/0xb80
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
vfs_write+0xe8/0x290
ksys_write+0xdc/0x130
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
This has been seen on PowerPC LPAR.
The root cause of this issue is that when node's memory is registered,
the range used can overlap another node's range, thus the memory block
is registered to multiple nodes in sysfs.
There are two issues here:
(a) The sysfs memory and node's layouts are broken due to these
multiple links
(b) The link errors in link_mem_sections() should not lead to a system
panic.
To address (a) register_mem_sect_under_node should not rely on the
system state to detect whether the link operation is triggered by a hot
plug operation or not. This is addressed by the patches 1 and 2 of this
series.
Issue (b) will be addressed separately.
This patch (of 2):
The memmap_context enum is used to detect whether a memory operation is
due to a hot-add operation or happening at boot time.
Make it general to the hotplug operation and rename it as
meminit_context.
There is no functional change introduced by this patch
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J . Wysocki" <rafael@kernel.org>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200915094143.79181-1-ldufour@linux.ibm.com
Link: https://lkml.kernel.org/r/20200915132624.9723-1-ldufour@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b8bd42361 upstream.
Currently io_ticks is approximated by adding one at each start and end of
requests if jiffies counter has changed. This works perfectly for requests
shorter than a jiffy or if one of requests starts/ends at each jiffy.
If disk executes just one request at a time and they are longer than two
jiffies then only first and last jiffies will be accounted.
Fix is simple: at the end of request add up into io_ticks jiffies passed
since last update rather than just one jiffy.
Example: common HDD executes random read 4k requests around 12ms.
fio --name=test --filename=/dev/sdb --rw=randread --direct=1 --runtime=30 &
iostat -x 10 sdb
Note changes of iostat's "%util" 8,43% -> 99,99% before/after patch:
Before:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sdb 0,00 0,00 82,60 0,00 330,40 0,00 8,00 0,96 12,09 12,09 0,00 1,02 8,43
After:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sdb 0,00 0,00 82,50 0,00 330,00 0,00 8,00 1,00 12,10 12,10 0,00 12,12 99,99
Now io_ticks does not loose time between start and end of requests, but
for queue-depth > 1 some I/O time between adjacent starts might be lost.
For load estimation "%util" is not as useful as average queue length,
but it clearly shows how often disk queue is completely empty.
Fixes: 5b18b5a737 ("block: delete part_round_stats and switch to less precise counting")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
From: "Banerjee, Debabrata" <dbanerje@akamai.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09a6b0bc3b ]
Commit f227e3ec3b ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in
83bdc7275e ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.
From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.
Fixes: 83bdc7275e ("random32: remove net_rand_state from the latent entropy gcc plugin")
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Thibaut Sautereau <thibaut.sautereau@ssi.gouv.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efe84d408b ]
When building with
$ HOST_EXTRACFLAGS=-g make
the expectation is that host tools are built with debug informations.
This however doesn't happen if the Makefile assigns a new value to the
HOST_EXTRACFLAGS instead of appending to it. So use += instead of := for
the first assignment.
Fixes: e3fd9b5384 ("scripts/dtc: consolidate include path options in Makefile")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2bd970aa6 ]
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e640b1eec ]
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0d394e88 ]
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac67b07e26 ]
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a26044954 ]
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376 ("iommu/exynos: Add callback for initializing devices from device tree")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3bb0f796f ]
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b57177 ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5105660ee8 ]
Commit bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
Fixes: bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
Reported-by: LABBE Corentin <clabbe@baylibre.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d33030e2ee ]
nfs_readdir_page_filler() iterates over entries in a directory, reusing
the same security label buffer, but does not reset the buffer's length.
This causes decode_attr_security_label() to return -ERANGE if an entry's
security label is longer than the previous one's. This error, in
nfs4_decode_dirent(), only gets passed up as -EAGAIN, which causes another
failed attempt to copy into the buffer. The second error is ignored and
the remaining entries do not show up in ls, specifically the getdents64()
syscall.
Reproduce by creating multiple files in NFS and giving one of the later
files a longer security label. ls will not see that file nor any that are
added afterwards, though they will exist on the backend.
In nfs_readdir_page_filler(), reset security label buffer length before
every reuse
Signed-off-by: Jeffrey Mitchell <jeffrey.mitchell@starlab.io>
Fixes: b4487b9354 ("nfs: Fix getxattr kernel panic and memory overflow")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63c3212e7a ]
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 850280156f ]
If devm_phy_create() fails then we need to call of_clk_del_provider(node)
to undo the call to of_clk_add_provider().
Fixes: 71e2f5c5c2 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200905124648.GA183976@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fcface659 ]
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")
Signed-off-by: Taiping Lai <taiping.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0e8dac98 ]
The lldd may have made calls to delete a remote port or local port and
the delete is in progress when the cli then attempts to create a new
controller. Currently, this proceeds without error although it can't be
very successful.
Fix this by validating that both the host port and remote port are
present when a new controller is to be created.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50b7c24390 ]
Currently, we use nvmeq->q_depth as the upper limit for a valid tag in
nvme_handle_cqe(), it is not correct. Because the available tag number
is recorded in tagset, which is not equal to nvmeq->q_depth.
The nvme driver registers interrupts for queues before initializing the
tagset, because it uses the number of successful request_irq() calls to
configure the tagset parameters. This allows a race condition with the
current tag validity check if the controller happens to produce an
interrupt with a corrupted CQE before the tagset is initialized.
Replace the driver's indirect tag check with the one already provided by
the block layer.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b867eef4cf ]
The SPIE register contains counts for the TX FIFO so any time the irq
handler was invoked we would attempt to process the RX/TX fifos. Use the
SPIM value to mask the events so that we only process interrupts that
were expected.
This was a latent issue exposed by commit 3282a3da25 ("powerpc/64:
Implement soft interrupt replay in C").
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200904002812.7300-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72f04da48a ]
It would seem none of the kernel continuous integration does this:
$ cd tools/io_uring
$ make
Otherwise it may have noticed:
cc -Wall -Wextra -g -D_GNU_SOURCE -c -o io_uring-bench.o
io_uring-bench.c
io_uring-bench.c:133:12: error: static declaration of ‘gettid’
follows non-static declaration
133 | static int gettid(void)
| ^~~~~~
In file included from /usr/include/unistd.h:1170,
from io_uring-bench.c:27:
/usr/include/x86_64-linux-gnu/bits/unistd_ext.h:34:16: note:
previous declaration of ‘gettid’ was here
34 | extern __pid_t gettid (void) __THROW;
| ^~~~~~
make: *** [<builtin>: io_uring-bench.o] Error 1
The problem on Ubuntu 20.04 (with lk 5.9.0-rc5) is that unistd.h
already defines gettid(). So prefix the local definition with
"lk_".
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 795d6379a4 ]
For 64bit CONFIG_BASE_SMALL=0 systems PID_MAX_LIMIT is set by default to
4194304. During boot the kernel sets a new value based on number of CPUs
but no lower than 32768. It is 1024 per CPU so with 128 CPUs the default
becomes 131072 which needs six digits.
This value can be increased during run time but must not exceed the
initial upper limit.
Systemd sometime after v241 sets it to the upper limit during boot. The
result is that when the pid exceeds five digits, the trace output is a
little hard to read because it is no longer properly padded (same like
on big iron with 98+ CPUs).
Increase the pid padding to seven digits.
Link: https://lkml.kernel.org/r/20200904082331.dcdkrr3bkn3e4qlg@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fb030a704 ]
This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.
1. Control frames in hdlc_cisco and hdlc_ppp
When these drivers send control frames, skb->protocol is not set.
This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.
2. hdlc_fr
When this driver sends control frames, skb->protocol is set to internal
values used in this driver.
When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).
However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83f9a9c8c1 ]
This driver is a virtual driver stacked on top of Ethernet interfaces.
When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.
This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.
This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 933a3752ba ]
the callers rely upon having any iov_iter_truncate() done inside
->direct_IO() countered by iov_iter_reexpand().
Reported-by: Qian Cai <cai@redhat.com>
Tested-by: Qian Cai <cai@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4202c9fdf0 ]
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee460417d2 ]
Increase Rx ring size to address issue where hardware is reaching
the receive work limit.
Before:
[ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached
Signed-off-by: Lucy Yan <lucyyan@google.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44a049c426 ]
PVC devices are virtual devices in this driver stacked on top of the
actual HDLC device. They are the devices normal users would use.
PVC devices have two types: normal PVC devices and Ethernet-emulating
PVC devices.
When transmitting data with PVC devices, the ndo_start_xmit function
will prepend a header of 4 or 10 bytes. Currently this driver requests
this headroom to be reserved for normal PVC devices by setting their
hard_header_len to 10. However, this does not work when these devices
are used with AF_PACKET/RAW sockets. Also, this driver does not request
this headroom for Ethernet-emulating PVC devices (but deals with this
problem by reallocating the skb when needed, which is not optimal).
This patch replaces hard_header_len with needed_headroom, and set
needed_headroom for Ethernet-emulating PVC devices, too. This makes
the driver to request headroom for all PVC devices in all cases.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc6717d55d ]
When the timer counts to the upper limit, an overflow interrupt is
generated, and the count is reset with the value in the TIME_INI
register. But the software expects to start counting from 0 when
the count overflows, so it forces TIME_INI to 0 to solve the
potential interrupt storm problem.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Tested-by: Xu Kai <xukai@nationalchip.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597735877-71115-1-git-send-email-guoren@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a39d0d7bdf upstream.
A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.
Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e008fa6fb4 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config")
Cc: stable@vger.kernel.org
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62c59a8786 upstream.
After commit 6827ca573c ("memstick: rtsx_usb_ms: Support runtime power
management"), removing module rtsx_usb_ms will be stuck.
The deadlock is caused by powering on and powering off at the same time,
the former one is when memstick_check() is flushed, and the later is called
by memstick_remove_host().
Soe let's skip allocating card to prevent this issue.
Fixes: 6827ca573c ("memstick: rtsx_usb_ms: Support runtime power management")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200925084952.13220-1-kai.heng.feng@canonical.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40341fad6 upstream.
The first thing that the ftrace function callback helper functions should do
is to check for recursion. Peter Zijlstra found that when
"rcu_is_watching()" had its notrace removed, it caused perf function tracing
to crash. This is because the call of rcu_is_watching() is tested before
function recursion is checked and and if it is traced, it will cause an
infinite recursion loop.
rcu_is_watching() should still stay notrace, but to prevent this should
never had crashed in the first place. The recursion prevention must be the
first thing done in callback functions.
Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net
Cc: stable@vger.kernel.org
Cc: Paul McKenney <paulmck@kernel.org>
Fixes: c68c0fa293 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fc27b098d upstream.
Touchpad on this laptop is not detected properly during boot, as PNP
enumerates (wrongly) AUX port as disabled on this machine.
Fix that by adding this board (with admittedly quite funny DMI
identifiers) to nopnp quirk list.
Reported-by: Andrés Barrantes Silman <andresbs2000@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2009252337340.3336@cbobk.fhfr.pm
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug existed in the XFS reflink code between v5.1 and v5.5 in which
the mapping for a COW IO was not trimmed to the mapping of the COW
extent that was found. This resulted in a too-short copy, and
corruption of other files which shared the original extent.
(This happened only when extent size hints were set, which bypasses
delalloc and led to this code path.)
This was (inadvertently) fixed upstream with
36adcbace2 "xfs: fill out the srcmap in iomap_begin"
and related patches which moved lots of this functionality to
the iomap subsystem.
Hence, this is a -stable only patch, targeted to fix this
corruption vector without other major code changes.
Fixes: 78f0cc9d55 ("xfs: don't use delalloc extents for COW on files with extsize hints")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df12eb6d6c ]
Whenever the vsock backend on the host sends a packet through the RX
queue, it expects an answer on the TX queue. Unfortunately, there is one
case where the host side will hang waiting for the answer and might
effectively never recover if no timeout mechanism was implemented.
This issue happens when the guest side starts binding to the socket,
which insert a new bound socket into the list of already bound sockets.
At this time, we expect the guest to also start listening, which will
trigger the sk_state to move from TCP_CLOSE to TCP_LISTEN. The problem
occurs if the host side queued a RX packet and triggered an interrupt
right between the end of the binding process and the beginning of the
listening process. In this specific case, the function processing the
packet virtio_transport_recv_pkt() will find a bound socket, which means
it will hit the switch statement checking for the sk_state, but the
state won't be changed into TCP_LISTEN yet, which leads the code to pick
the default statement. This default statement will only free the buffer,
while it should also respond to the host side, by sending a packet on
its TX queue.
In order to simply fix this unfortunate chain of events, it is important
that in case the default statement is entered, and because at this stage
we know the host side is waiting for an answer, we must send back a
packet containing the operation VIRTIO_VSOCK_OP_RST.
One could say that a proper timeout mechanism on the host side will be
enough to avoid the backend to hang. But the point of this patch is to
ensure the normal use case will be provided with proper responsiveness
when it comes to establishing the connection.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c7246dc45 ]
We are going to add 'struct vsock_sock *' parameter to
virtio_transport_get_ops().
In some cases, like in the virtio_transport_reset_no_sock(),
we don't have any socket assigned to the packet received,
so we can't use the virtio_transport_get_ops().
In order to allow virtio_transport_reset_no_sock() to use the
'.send_pkt' callback from the 'vhost_transport' or 'virtio_transport',
we add the 'struct virtio_transport *' to it and to its caller:
virtio_transport_recv_pkt().
We moved the 'vhost_transport' and 'virtio_transport' definition,
to pass their address to the virtio_transport_recv_pkt().
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 214b0e1ad0 upstream.
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
Fixes: d88b25be35 ("gpio: Add TC35892 GPIO driver")
Cc: Cc: stable@vger.kernel.org
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b02d9e770 upstream.
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45ccf65567 upstream.
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de
Fixes: be8c8facc7 ("gpio: new driver to work with a 8x12 siox")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b405533c2 upstream.
commit 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200920170158.1217068-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afd7f30886 upstream.
Commit bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on
Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models
because of it being broken due to what is believed to be a bug in
the BIOS.
It seems that the BIOS of some IRBIS models, including the IRBIS NB111
model has the same issue, so disable command queuing there too.
Fixes: bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on Intel GLK")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209397
Reported-and-tested-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200927104821.5676-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c8f353272 upstream.
We use a device's allocation state tree to track ranges in a device used
for allocated chunks, and we set ranges in this tree when allocating a new
chunk. However after a device replace operation, we were not setting the
allocated ranges in the new device's allocation state tree, so that tree
is empty after a device replace.
This means that a fitrim operation after a device replace will trim the
device ranges that have allocated chunks and extents, as we trim every
range for which there is not a range marked in the device's allocation
state tree. It is also important during chunk allocation, since the
device's allocation state is used to determine if a range is already
allocated when allocating a new chunk.
This is trivial to reproduce and the following script triggers the bug:
$ cat reproducer.sh
#!/bin/bash
DEV1="/dev/sdg"
DEV2="/dev/sdh"
DEV3="/dev/sdi"
wipefs -a $DEV1 $DEV2 $DEV3 &> /dev/null
# Create a raid1 test fs on 2 devices.
mkfs.btrfs -f -m raid1 -d raid1 $DEV1 $DEV2 > /dev/null
mount $DEV1 /mnt/btrfs
xfs_io -f -c "pwrite -S 0xab 0 10M" /mnt/btrfs/foo
echo "Starting to replace $DEV1 with $DEV3"
btrfs replace start -B $DEV1 $DEV3 /mnt/btrfs
echo
echo "Running fstrim"
fstrim /mnt/btrfs
echo
echo "Unmounting filesystem"
umount /mnt/btrfs
echo "Mounting filesystem in degraded mode using $DEV3 only"
wipefs -a $DEV1 $DEV2 &> /dev/null
mount -o degraded $DEV3 /mnt/btrfs
if [ $? -ne 0 ]; then
dmesg | tail
echo
echo "Failed to mount in degraded mode"
exit 1
fi
echo
echo "File foo data (expected all bytes = 0xab):"
od -A d -t x1 /mnt/btrfs/foo
umount /mnt/btrfs
When running the reproducer:
$ ./replace-test.sh
wrote 10485760/10485760 bytes at offset 0
10 MiB, 2560 ops; 0.0901 sec (110.877 MiB/sec and 28384.5216 ops/sec)
Starting to replace /dev/sdg with /dev/sdi
Running fstrim
Unmounting filesystem
Mounting filesystem in degraded mode using /dev/sdi only
mount: /mnt/btrfs: wrong fs type, bad option, bad superblock on /dev/sdi, missing codepage or helper program, or other error.
[19581.748641] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi started
[19581.803842] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi finished
[19582.208293] BTRFS info (device sdi): allowing degraded mounts
[19582.208298] BTRFS info (device sdi): disk space caching is enabled
[19582.208301] BTRFS info (device sdi): has skinny extents
[19582.212853] BTRFS warning (device sdi): devid 2 uuid 1f731f47-e1bb-4f00-bfbb-9e5a0cb4ba9f is missing
[19582.213904] btree_readpage_end_io_hook: 25839 callbacks suppressed
[19582.213907] BTRFS error (device sdi): bad tree block start, want 30490624 have 0
[19582.214780] BTRFS warning (device sdi): failed to read root (objectid=7): -5
[19582.231576] BTRFS error (device sdi): open_ctree failed
Failed to mount in degraded mode
So fix by setting all allocated ranges in the replace target device when
the replace operation is finishing, when we are holding the chunk mutex
and we can not race with new chunk allocations.
A test case for fstests follows soon.
Fixes: 1c11b63eff ("btrfs: replace pending/pinned chunks lists with io tree")
CC: stable@vger.kernel.org # 5.2+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Dufour