Now that the clock driver has support for the A31 clocks, we can add
them to the DTSI and start using them in the relevant hardware blocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10s has only a subset of the A10 gates. Now that the clock driver
has support for this gates set, switch to it in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
The Cubieboard2 is the successor of the first Cubieboard, and shares the
same hardware, except that the Allwinner A10 found initially has been
replaced by an Allwinner A20.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20-olinuxino Micro has a LED connected to the PH2 pin. Use the
gpio-led driver to enable the control over this LED.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Instead of relying on the bootloader to mux the UART pins properly, do
it on our own and register the rightful pins for the A20-olinuxino in
the DT using pinctrl.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UARTs on the A20 can be muxed to several pins. Add a few options to
the DTSI so that we can start using them in the boards' DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO controller is responsible for the GPIO/muxing/external
interrupts handling. Now that we have support for the A20 pin set in the
pinctrl driver, we can start using it in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has a different set of pins than the one found on the A10 and
A13. Now that we have support for the A31 pin set in the pinctrl driver,
we can enable it in the DTSI with its own compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A20-Olinuxino is an open-hardware board based on the
Allwinner A20 SoC, with most of the pins exported on headers, a 10/100M
ethernet port, SATA, SD and uSD slots, etc.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A20 SoC is based on 2 Cortex A7, an ARM Mali GPU, and is
built to be pin-compatible with the older Allwinner A10.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This platform from WITS is the evaluation board for the Allwinner A31.
It features a quad-Cortex A7, 2048MB of RAM, NAND, USB, MMC, several
UART, HDMI, a 2048 x 1536 10" screen, powered by a PowerVR, etc.
Of course, most of these peripherals aren't supported yet, but support
for those will come eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds a device tree usable on Mele A1000 (and A2000, as it
apparently is the same device except for the case). This device features
one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
LEDs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[maxime: fixed the soc node address]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There was a typo in the base address used for the soc node in the A13
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg property of the simple-bus driver is completely useless. Remove
it from the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There was a typo in the base address used for the soc node in the A10s
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg property of the simple-bus driver is completely useless. Remove
it from the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There was a typo in the base address used for the soc node in the A10
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg property of the simple-bus driver is completely useless. Remove
it from the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Quoting from Documentation/leds/leds-class.txt:
LED Device Naming
=================
Is currently of the form:
"devicename:colour:function"
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This OLIMEX board has a AT24C16BN-SH EEPROM holding the MAC address.
This patch adds the corresponding device tree node to reflect this.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board from OLIMEX is using the three I2C controllers present on A10S:
* I2C-0 connects to the AXP152 PMU
* I2C-1 holds an AT24C16BN-SH EEPROM with the MAC address for ethernet
* I2C-2 is used for UEXT modules.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A10S has 3 I2C controllers embedded on it. Add them to the
corresponding dtsi.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The information has been extracted from the A10S-OLinuXino-Micro
schematics, as we do not have a user manual for A10S yet.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull more vfs stuff from Al Viro:
"O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
making simple_lookup() usable for filesystems with non-NULL s_d_op,
which allows us to get rid of quite a bit of ugliness"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sunrpc: now we can just set ->s_d_op
cgroup: we can use simple_lookup() now
efivarfs: we can use simple_lookup() now
make simple_lookup() usable for filesystems that set ->s_d_op
configfs: don't open-code d_alloc_name()
__rpc_lookup_create_exclusive: pass string instead of qstr
rpc_create_*_dir: don't bother with qstr
llist: llist_add() can use llist_add_batch()
llist: fix/simplify llist_add() and llist_add_batch()
fput: turn "list_head delayed_fput_list" into llist_head
fs/file_table.c:fput(): add comment
Safer ABI for O_TMPFILE
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull perf fixes from Thomas Gleixner:
- fix for do_div() abuse on x86
- locking fix in perf core
- a pile of (build) fixes and cleanups in perf tools
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86: Fix incorrect use of do_div() in NMI warning
perf: Fix perf_lock_task_context() vs RCU
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
perf: Clone child context from parent context pmu
perf script: Fix broken include in Context.xs
perf tools: Fix -ldw/-lelf link test when static linking
perf tools: Revert regression in configuration of Python support
perf tools: Fix perf version generation
perf stat: Fix per-socket output bug for uncore events
perf symbols: Fix vdso list searching
perf evsel: Fix missing increment in sample parsing
perf tools: Update symbol_conf.nr_events when processing attribute events
perf tools: Fix new_term() missing free on error path
perf tools: Fix parse_events_terms() segfault on error path
perf evsel: Fix count parameter to read call in event_format__new
perf tools: fix a typo of a Power7 event name
perf tools: Fix -x/--exclude-other option for report command
perf evlist: Enhance perf_evlist__start_workload()
perf record: Remove -f/--force option
perf record: Remove -A/--append option
...
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
[suggested by Rasmus Villemoes] make O_DIRECTORY | O_RDWR part of O_TMPFILE;
that will fail on old kernels in a lot more cases than what I came up with.
And make sure O_CREAT doesn't get there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
OMAP recently changed how the platforms are configured, so OMAP2/3/4 SoC
support is no longer enabled by default. Add them back.
Enable new ethernet driver for sunxi.
The i.MX console options moved due to resorting, no functional change.
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=qQ9Q
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij:
Ux500 defconfig changes:
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable HIGHMEM in the u8500 defconfig
ARM: ux500: Update MMC configs for u8500 defconfig
ARM: ux500: select SND_SOC_UX500 for ux500
ARM: ux500: update defconfig base
ARM: ux500: select WATCHDOG and MUSB for ux500
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add i.MX serial console support. This gives us the boot messages on
UART on e.g. the i.MX6Q sabre sd platform.
- Add the necessary config options, to allow booting with NFS root on
an i.MX6 sabre sd.
- Add Freescale LPUART serial console support. This gives us the boot
messages on UART on e.g. the Vybrid VF610 Tower board.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Russell King <linux@arm.linux.org.uk>
[olof: squashed three commits down to one]
Signed-off-by: Olof Johansson <olof@lixom.net>
get in before -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kO4u
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
I completely botched understanding the calling conventions of
do_div(). I assumed that do_div() returned the result instead
of realizing that it modifies its argument and returns a
remainder. The side-effect from this would be bogus numbers
for the "msecs" value in the warning messages:
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.114 msecs
Note, there was a second fix posted by Stephane Eranian for
a separate patch which I also botched:
http://lkml.kernel.org/r/20130704223010.GA30625@quad
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20130708214404.B0B6EA66@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
Pull more KVM changes from Gleb Natapov:
"A fix for a bug that prevents some guests from working on old Intel
CPUs and a patch that integrates ARM64 KVM, merged via ARM64 tree,
into Kconfig."
* tag 'kvm-3.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: mark unusable segment as nonpresent
arm64: KVM: Kconfig integration
Pull Sparc bugfixes from David Miller:
"Four bug fixes:
1) Enable snoop tags properly on Sparc32/LEON, from Andreas Larsson
2) strcpy() length check fix from Chen Gang.
3) Forgotten unregister_netdev() in sunvnet driver, from Dave
Kleikamp.
4) Fix broken assembler offsets used in vm_area_struct accesses on
sparc32, from Olivier DANET."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
[PATCH] sparc32: vm_area_struct access for old Sun SPARCs.
sunvnet: vnet_port_remove must call unregister_netdev
sparc32, leon: Require separate snoop tags set to regard snooping to be enabled
arch: sparc: kernel: check the memory length before use strcpy().
Merge more patches from Andrew Morton:
"The rest of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: remove free_area_cache
zswap: add documentation
zswap: add to mm/
zbud: add to mm/
Since all architectures have been converted to use vm_unmapped_area(),
there is no remaining use for the free_area_cache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.
a patch for the socket.7 man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Ripard