Added new log level mechanism for different events. These
log levels can be set at driver load time/run time. The
log level is set for each Scsi_host.
Fixed few multi-line print warning to get over the new checkpatch.pl
warnings on multi-line strings.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the driver comes up in crashdump mode, it has to explicitly
issue command to FW for logging to the boot target. This fix issues
MBX Cmd to login to boot target in crashdump mode.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The setting of iscsi_data_pdu is not required anymore,
as this was required for BE1 adapters only. The BE1 adapter
were not supported in any previous versions of the kernel.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make compliant with FC specs by sending LOGO after ABTS timeouts
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC and iSCSI class set SCSI devices to transport-offline state after
fast_io_fail/replacement_timeout has fired, but after relogin, function
scsi_internal_device_unblock() is not setting scsi device state to running.
Due to this the devices even after being relogged in remain offline.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The current code would incorrectly return a DID_OK for a
CHECK CONDITION with Recovered error sense key causing incorrect
completion of a command when there is a dropped frame.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During iscsid session recovery driver sends multiple ISCSI_CONN_STATE_LOGGED_IN
event from qla4xxx_conn_start() and qla4xxx_ddb_change(), which causes iscsid
to crash.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix warning:-
drivers/scsi/qla4xxx/ql4_nx.c:1867:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘uint32_t’ [-Wformat]
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In qla4xxx_ep_connect(), qla_ep->dst_addr and dst_addr are type
struct sockaddr. We are copying sizeof(struct sockaddr_in6) bytes
from dst_addr to qla_ep->dst_addr which is 12 bytes larger. This
will cause memory corruption. So we change qla_ep->dst_addr to
struct sockaddr_storage which is of 128 byte, large enough to
hold sizeof(struct sockaddr_in6).
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add fcp_io_channel module attribute to control amount of parallel I/O queues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commonize SLI-3/4 Ring/Queue framework, to keep SLI-3 compatibility
Parallelize SLI-4 Q distribution - to use multiple posting/completion queues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a MAINTAINERS entry for the IBM Power Virtual SCSI and FC device
drivers.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
"rc" is always zero here, so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We recently changed the locking in this function, but this return was
missed. It needs an unlock and the IRQs need to be restored.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Without this patch, scsi_show_result prints hostbyte as invalid for statuses
that are not defined in hostbyte_table (when scsi logging is enabled).
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
I think ioremap() ends up being equivalent to ioremap_nocache
by default, but we should signal our intent that these mappings
should be non-cacheable.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the abort handler, when asked to abort a command which
is not known to the driver, SUCCESS is returned, but the
diagnostic message incorrectly indicates the abort failed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line. Symptoms look like this:
hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:
LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts. So we should use LUN reset,
not target reset.
Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
