The NAND DQS pins are currently named nand_dqs_0 and nand_dqs_1.
However, they both seem to have the same function, just exposed on
different pins (unlike the ethernet TX pins for example, where there's
eth_txd0..3 - all of these can be active at the same time as they are
different data lines).
Rename the NAND DQS pins to nand_dqs_15 and nand_dqs_18 to reflect that
it's the same functionality just exposed on different pins (BOOT_15 and
BOOT_18).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nand_groups table uses different names for the NAND DQS pins than
the GROUP() definition in meson8b_cbus_groups (nand_dqs_0 vs nand_dqs0).
This prevents using the NAND DQS pins in the devicetree.
Fix this by ensuring that the GROUP() definition and the
meson8b_cbus_groups use the same name for these pins.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add basic support for the Pin Function Controller on revision ES2.0
of the R-Car H3 SoC, which differs from ES1.x in many ways.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fKYc
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.12 (take two)
- Add basic support for the Pin Function Controller on revision ES2.0
of the R-Car H3 SoC, which differs from ES1.x in many ways.
Add pins, groups, and a function for SCIF_CLK on R-Car H3 ES2.0.
SCIF_CLK is the external clock source for the Baud Rate Generator for
External Clock (BRG) on (H)SCIF serial ports.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Add pins, groups, and functions for all SCIF serial ports on R-Car H3
ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
The Pin Function Controller module in the R-Car H3 ES2.0 differs from
ES1.x in many ways.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
Hence this patch:
1. Extracts the support for R-Car H3 ES1.x into a separate file, as
the differences are quite large,
2. Adds code for detecting the SoC revision at runtime using the new
soc_device_match() API, and selecting pinctrl tables for the actual
SoC revision,
3. Replaces the core register and bitfield definitions by their
counterparts for R-Car H3 ES2.0.
The addition of pins, groups, and functions for the various on-chip
devices is left to subsequent patches.
The R-Car H3 ES2.0 register and bitfield definitions were extracted from
a patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
When trying to add a gpio-hog, we enter a weird loop where the gpio-ranges
is needed when gpiochip_add_data() is called but in the current implementation
the ranges are added from the driver afterwards.
A simple solution is to rely on the DR gpio-ranges attribute and remove the
call to gpiochip_add_pin_range().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix some inverted bit numbers in some pinctrl groups and add missing pins
and groups to be in pair with the GXBB pinctrl pins definition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With real-time preemption, regmap functions cannot be used in the
implementation of irq_chip since they use spinlocks which may sleep.
Move the setting of the mux for IRQs to an irq_bus_sync_unlock handler
where we are allowed to sleep.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to avoid calling regmap functions from irq handlers, so the next
commit is going to move the call to rockchip_set_mux() into an
irq_bus_sync_unlock handler. But we can't return an error from there so
we still need to check the settings from rockchip_irq_set_type() and we
will use this new rockchip_verify_mux() function from there.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This lock is used from rockchip_irq_set_type() which is part of the
irq_chip implementation and thus must use raw_spinlock_t as documented
in Documentation/gpio/driver.txt.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
regmap_update_bits does its own locking and everything else accessed
here is a local variable so there is no need to lock around it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some Cherry Trail devices the ASL uses the GMMR GPIO to access
GPIOs so as to serialize MMIO accesses to GPIO registers with the
OS, because:
"Due to a silicon issue, a shared lock must be used to prevent concurrent
accesses across the 4 GPIO controllers.
See Intel Atom Z8000 Processor Series Specification Update (Rev. 005),
errata #CHT34, for further information."
This commit adds support for this opregion, this fixes a number of
ASL errors on my Ezpad mini3 tablet and makes the otg port device/host
muxing which is controlled in firmware on this model work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapted rk1108 dtsi to keep bisectability]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we are trying to enable/disable the clk of irq's gpio bank when
unmask/mask irq. But the kernel's "lazy disable approach" will skip masking
irq when the irq chip doesn't support irq_disable ops.
So we may hit this case:
irq_enable-> enable clk
irq_disable-> noop
irq_enable-> enable clk again
irq_disable-> noop
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At first these drivers were written as tristate, but the module
usecases are actually not tested. Make all of them boolean.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 3e030b0b4e ("pinctrl: uniphier: allow to have pinctrl
node under syscon node"), this driver has kept compatibility for the
old DT files. Several releases have passed since then, so remove
the obsoleted compatibles and clean up the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the missing PWM pins on Meson GXL SoCs, namely:
- PWM_A
- PWM_B
- PWM_C
- PWM_F (GPIOX_7 and GPIOCLK_1 can be selected as output)
- PWM_AO_A (GPIOAO_3 and GPIOAO_8 can be selected as output)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the sh_pfc_soc_info pointer after calling the SoC-specific
initialization function, as it may have been updated to e.g. handle
different SoC revisions. This makes sure the correct subdriver name is
printed later.
Fixes: 0c151062f3 ("sh-pfc: Add support for SoC-specific initialization")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Somehow the QSPI and SCIF_CLK fragments were inserted at the wrong
positions. Restore sort order (alphabetically, per group).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The sunxi pinctrl driver currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sirf atlas7 pinctrl drivers currently implement an irq_chip for
handling interrupts; due to how irq_chip handling is done, it's
necessary for the irq_chip methods to be invoked from hardirq context,
even on a a real-time kernel. Because the spinlock_t type becomes a
"sleeping" spinlock w/ RT kernels, it is not suitable to be used with
irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The amd pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bcm pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sysfs and debugfs entries for pin control drivers work better when
the individual pins are given real names, even if they are all just
"gpio0", "gpio1", etc.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prevent external signal crosstalk, some pins need to
enable input schmitt, like i2c pins, 32k-input pin and so on.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner pin controllers are also GPIO controllers.
Currently, if GPIOLIB is forgot to be chosen, the build of
pinctrl-sunxi.c will fail for lacking a lot of gpiochip_* functions.
Select GPIOLIB to ensure this driver can be built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A64 has a R_PIO pin controller, similar to the one found on the H3 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 Allwinner SoCs used to have every pinctrl driver selected in
ARCH_SUNXI. Change this to make their default value to (ARM64 &&
ARCH_SUNXI).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just fix spelling typos in comments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Port D and port E GPIO loopback modes are commonly enabled via hardware
straps for use with front-panel buttons. When the BMC is powered
off or fails to boot, the front-panel buttons are directly connected to
the host chipset via the loopback to allow direct power-on and reset
control. Once the BMC has booted, the loopback mode must be disabled for
the BMC to take over control of host power-on and reset.
Disabling these loopback modes requires writing to the hardware strap
register which violates the current design of assuming the system
designer chose the strap settings for a specific reason and they should
be treated as read-only. Only the two bits of the strap register related
to these loopback modes are allowed to be written and comments have been
added to explain why.
Signed-off-by: Rick Altherr <raltherr@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Note, the iomux of following pins are special, need to
be recalculated specially.
- gpio2_b4
- gpio2_b7
- gpio2_c7
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins are special at a bank so that add
IOMUX_RECALCED type to indicate which iomux source
of the bank need to be recalculated. If the mux
recalculateed callback and IOMUX_RECALCED type
were set, recalculate the pins' iomux by using
mux recalculated data struct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local variable drvdata is not used in samsung_gpio_set_direction.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typos and add the following to the scripts/spelling.txt:
overrided||overridden
Link: http://lkml.kernel.org/r/1481573103-11329-22-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). Fix by using devm_ioremap_resource instead of devm_ioremap.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to unlock before returning -EINVAL on this error path.
Fixes: 04cc058f0c ("pinctrl: intel: Add support for 1k additional pull-down")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: "Antoine Ténart" <antoine.tenart@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get the exact same change, so they are handled in batch.
Changes are (1) use init.h header in place of module.h header,
(2) delete module_exit related code, (3) delete MODULE_DEVICE_TABLE,
and (4) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
None of these drivers were using module_init() so we don't have to
worry about the init ordering getting changed with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: spear-devel@list.st.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate, meaning
that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only.
All drivers get the exact same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) dont use module.h
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
For the dove driver we explicitly disallow a driver unbind, since
that doesn't have a sensible use case anyway, and it allows us to
drop the ".remove" code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We deleted the MODULE_LICENSE etc. tags since all that information
is already contained at the top of the file in the comments.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Martin Blumenstingl