Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.
Do the ASoC side of this by storing the enable state in the core driver
structure and only writing to the device if a flag indicating that the
accessory detection side is in a state where it can have the headphone
output stage enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems use the audio CODEC to clock a DAI with multiple data lines
in parallel, meaning that bit clocks are only required for a smaller number
of channels than data is sent for. In some cases providing the extra bit
clocks can take the other devices on the audio bus out of spec.
Support such systems by allowing a maximum number of channels to be
specified.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the tps65090 charger driver. This driver is
responsible for controlling the charger aspect of the tps65090 mfd.
Currently, this mainly consists of turning on and off the charger, but
some features of the charger can be supported through this driver
including:
- Enable Auto Recharge based on Battery voltage
- Fast Charge Safety Timer
- Maximum battery discharge current
- Maximum battery adapter current
- Enable External Charge
- Disable charging termination based on low charger current (supported)
Once the driver is accepted, later patches can add support for the
features above which are not yet supported.
Based on work by:
Syed Rafiuddin <srafiuddin@nvidia.com>
Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
From Lee Jones <lee.jones@linaro.org>:
"Please find the next instalment of the AB8500 Power drivers upgrade. A lot of
work has taken place on the internal development track, but little effort has
gone into mainlining it. There is a large backlog of patches which are in need
of forward-porting, then upstreaming. This patch-set aims to make a large dent
into them."
Conflicts:
drivers/mfd/ab8500-gpadc.c
This patch set default value of MUIC register to bring up MUIC device.
If user don't set some initial value for MUIC device through platform data,
extcon-max77693 driver use 'default_init_data' to bring up base operation
of MAX77693 MUIC device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Clean up interrupts on exit, silencing a sparse warning caused by
tps65912_irq_exit() being defined but not prototyped as we go.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently driver sets the irq type to IRQF_TRIGGER_LOW which is
causing interrupt registration failure in ARM based SoCs as:
[ 0.208479] genirq: Setting trigger mode 8 for irq 118 failed (gic_set_type+0x0/0xf0)
[ 0.208513] dummy 0-0059: Failed to request IRQ 118: -22
Provide the irq flags through platform data if device is registered
through board file or get the irq type from DT node property in place
of hardcoding the irq flag in driver to support multiple platforms.
Also configure the device to generate the interrupt signal according to
flag type.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the state of USB Charge detection is changed then the calls
use a define for another register in other bank. This change
creates a new define for the correct register and removes the
magic numbers that are present.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Provide AB8540 platform specific information required to run the
Battery Management subsystem on AB8540 based devices. For this to
happen we see the introduction of separate platform specific data
structures and a means in which to process them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AB8540 supports power path function in USB charging mode for fast
power up with dead and weak battery, and it could extend
the battery age.
When USB charging starts, if the Vbattrue is below than SW cut off
voltage, power path and pre-charge should be enabled. If Vbattrue
is higher than SW cut off voltage, power path and pre-charge should
be disabled. This is to make sure full current to battery charge.
At the end of charge, power path should be enable again to reduce
charging the battery again.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Due to a bug in some AB8500 ASICs charger removal cannot always
be detected if the removal and reinsertion is done to close in time.
This patch detects above described case and handles the situation
so that charging will be kept turned on.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add 2.7v, 2.9v, 3.0v, 3.2v and 3.3v charging voltages for backup
battery. Before that only 2.5v, 2.6v, 2.8v, 3.1v were available.
Signed-off-by: Yang QU <yang.qu@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Xiao Mei ZHANG <xiaomei.zhang@stericsson.com>
Add support for a power cut feature which allows user to
configure when ab8505 and ab8540 based platforms should shut
down system due to low battery.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow GPADC debug information to be shown when executing on an AB8540
based platform.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This patch enables the GPADC to work on AB8540 based platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add a new reset function which uses the AB WD with 0 timeout.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
ITSource/ITLatch 7, 8, 9 and 10 don't exist on AB8540. This patch
replaces them with '-1' in the interrupt list, and handles the '-1'
in the code accordingly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add the support of gpacd hw conversion and make the number of
sample configurable.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
In L9540, turn_on_status register is not updated correctly if
the device is rebooted with AC/USB charger connected. Due to
this, the device boots android instead of entering into charge
only mode. Read the AC/USB status register to detect the charger
presence and update the turn on status manually.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Rupesh KUMAR <rupesh.kumar@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Rupesh KUMAR <rupesh.kumar@stericsson.com>
Tested-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
dri= ver and current sinks. This patch enables LP8788 backlight module.
(Brightness mode)
The brightness is controlled by PWM input or I2C register.
All modes are supported in the driver.
(Platform data)
Configurable data can be defined in the platform side.
name : backlight driver name. (default: "lcd-backlight")
initial_brightness : initial value of backlight brightness
bl_mode : brightness control by PWM or lp8788 register
dim_mode : dimming mode selection
full_scale : full scale current setting
rise_time : brightness ramp up step time
fall_time : brightness ramp down step time
pwm_pol : PWM polarity setting when bl_mode is PWM based
period_ns : platform specific PWM period value. unit is nano.
The default values are set in case no platform data is defined.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
The tmio_mmc_cd_wakeup() inline function has been deprecated since 3.4 and
is unused since 3.4 too. Remove them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
The biggest change in this update is the unification of HD-audio codec
parsers. Now the HD-audio codec is parsed in a generic parser code
which is invoked by each HD-audio codec driver. Some background
information is found in David Henningsson's blog entry:
http://voices.canonical.com/david.henningsson/2013/01/18/upcoming-changes-to-the-intel-hda-drivers/
Other than that, some random updates/fixes like USB-audio and a bunch
of small AoC updates as usual.
Highlights:
- Unification of HD-audio parser code (aka generic parser)
- Support of new Intel HD-audio controller, new IDT codecs
- Fixes for HD-audio HDMI audio hotplug
- Haswell HDMI audio fixup
- Support of Creative CA0132 DSP code
- A few fixes of HDSP driver
- USB-audio fix for Roland A-PRO, M-Audio FT C600
- Support PM for aloop driver (and fixes Oops)
- Compress API updates for gapless playback support
For ASoC part:
- Support for a wider range of hardware in the compressed stream code
- The ability to mute capture streams as well as playback streams while
inactive
- DT support for AK4642, FSI, Samsung I2S and WM8962
- AC'97 support for Tegra
- New driver for max98090, replacing the stub which was there
- A new driver from Dialog
Note that due to dependencies, DTification of DMA support for Samsung
platforms (used only by the and I2S driver and SPI) is merged here as
well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRJjy2AAoJEGwxgFQ9KSmk4EoP/RRslXfGAb+lrWeehmh9oHQL
P4JX+Cgv4OFFxaVjU7IgdjBCCnUNZoQ/Nm8wnpDbF+qP7DTcryPnuwWH8oaHLFSJ
+knbbbOShC6hxUzd+ZbxQpEn+4mupSC9+egzczz0wcK1kzAf8CO/rj17t3VxsoW/
Qa1yCWy6jbOmLu3JDpJTPyLfwA3x4/i3ViyTYfqgLP5kQHZZiv1eA9b682HFX9xQ
uDQipb040k7wBLoeZosR8iF/EDuPHls8H2ASCmZw0K2scZgBok0SkI6BBwsCg2z3
VbD9EkZmobRHwmubfDV1yCti050YnwGUbrN9tNpdSdv2cogKCkkxQ+zL8PX6Qf0l
D1neA9JJPhSMx5fufDnG5oTghx/XlHsTJKmrJNu8Gr/14pAmSbNF8iIOFfYju++2
LlpHLlwS4hxNYY0W3iAFTXi50BUng38tdhBCyZTgN2tSHaTwtdWvrVyizjpUa18N
onjvFtceULtudddosJWkaKUSqHLN/CWmIWXufucfjxEk5exXjPBMhYTsvhmM3I5D
zrK0GxUQqey7RToa48Sxs0iL269labUwH/8H1iMTL3/9UCCOqVRKR3X7NdGi3xtK
EiEiCeNoZX8PojGqSEkmRifOJ19gBxchZDNO4ruct0Omc4Jn/nOlHbi4jXghgr9H
D62m5PriiCnyBswjzKaX
=nIPc
-----END PGP SIGNATURE-----
Merge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The biggest change in this update is the unification of HD-audio codec
parsers. Now the HD-audio codec is parsed in a generic parser code
which is invoked by each HD-audio codec driver.
Some background information is found in David Henningsson's blog
entry:
http://voices.canonical.com/david.henningsson/2013/01/18/upcoming-changes-to-the-intel-hda-drivers/
Other than that, some random updates/fixes like USB-audio and a bunch
of small AoC updates as usual.
Highlights:
- Unification of HD-audio parser code (aka generic parser)
- Support of new Intel HD-audio controller, new IDT codecs
- Fixes for HD-audio HDMI audio hotplug
- Haswell HDMI audio fixup
- Support of Creative CA0132 DSP code
- A few fixes of HDSP driver
- USB-audio fix for Roland A-PRO, M-Audio FT C600
- Support PM for aloop driver (and fixes Oops)
- Compress API updates for gapless playback support
For ASoC part:
- Support for a wider range of hardware in the compressed stream code
- The ability to mute capture streams as well as playback streams
while inactive
- DT support for AK4642, FSI, Samsung I2S and WM8962
- AC'97 support for Tegra
- New driver for max98090, replacing the stub which was there
- A new driver from Dialog
Note that due to dependencies, DTification of DMA support for Samsung
platforms (used only by the and I2S driver and SPI) is merged here as
well."
Fix up trivial conflict in drivers/spi/spi-s3c64xx.c due to removed code
being changed.
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (453 commits)
ALSA: usb: Fix Processing Unit Descriptor parsers
ALSA: hda - hdmi: Notify userspace when ELD control changes
ALSA: hda - hdmi: Protect ELD buffer
ALSA: hda - hdmi: Refactor hdmi_eld into parsed_hdmi_eld
ALSA: hda - hdmi: Do not expose eld data when eld is invalid
ALSA: hda - hdmi: ELD shouldn't be valid after unplug
ALSA: hda - Fix the silent speaker output on Fujitsu S7020 laptop
ALSA: hda - add quirks for mute LED on two HP machines
ALSA: usb/quirks, fix out-of-bounds access
ASoC: codecs: Add da7213 codec
ALSA: au88x0 - Define channel map for au88x0
ALSA: compress: add support for gapless playback
ALSA: hda - Remove speaker clicks on CX20549
ALSA: hda - Disable runtime PM for Intel 5 Series/3400
ALSA: hda - Increase badness for missing multi-io
ASoC: arizona: Automatically manage input mutes
ALSA: hda - Fix broken workaround for HDMI/SPDIF conflicts
ALSA: hda/ca0132 - Add missing \n to debug prints
ALSA: hda/ca0132 - Fix type of INVALID_CHIP_ADDRESS
ALSA: hda - update documentation for no-primary-hp fixup
...
o goldfish_battery:
This is Android Emulator battery driver. Originally from Google, but
Intel folks reshaped it for mainline;
o pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses AB8500
battery management core;
o qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes;
o restart-poweroff:
A generic driver that implements 'power off by restarting'. The actual
poweroff functionality is implemented through a bootloader, so Linux'
task is just to restart the box. The driver is useful on Buffalo
Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked on
submitting the driver (as well as qnap-poweroff above).
- A lot of fixes for ab8500 drivers. This is a part of efforts of syncing
internal ST-Ericsson development tree with the mainline. Lee Jones @
Linaro worked on compilation and reshaping these series;
- New health properties for the power supplies: "Watchdog timer expire"
and "Safety timer expire";
- As usual, a bunch of fixes/cleanups here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=955B
-----END PGP SIGNATURE-----
Merge tag 'for-v3.9' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
- Grabbing of default pinctrl handles from the device core.
These are the hunks hitting drivers/base. All is ACKed by
Greg, after a long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has
been coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500,
AB8505, AB9540 and AB8540.
- Make it possible for hogged pins to enter a sleep mode,
and make it possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to
various pin controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=SQ9W
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the main pinctrl changes for the v3.9 merge window. The
most interesting change by far is how the device core grabs pinctrl
default handles avoiding the need to stick boilerplate into driver
consumers.
- Grabbing of default pinctrl handles from the device core. These
are the hunks hitting drivers/base. All is ACKed by Greg, after a
long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has been
coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500, AB8505, AB9540
and AB8540.
- Make it possible for hogged pins to enter a sleep mode, and make it
possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to various pin
controllers."
* tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (68 commits)
pinctrl: tegra: add clfvs function to Tegra114 support
pinctrl: generic: rename input schmitt disable
pinctrl/pinconfig: add debug interface
pinctrl: samsung: remove duplicated line
ARM: ux500: use real AB8500 IRQ numbers instead of virtual ones
ARM: ux500: remove irq_base property from platform_data
pinctrl/abx500: use direct IRQ defines
pinctrl/abx500: replace IRQ offsets with table read-in values
pinctrl/abx500: move IRQ handling to ab8500-core
pinctrl: exynos5440: remove erroneous __init
pinctrl/abx500: adjust offset for get_mode()
pinctrl/abx500: add Device Tree support
pinctrl/abx500: align GPIO cluster boundaries
pinctrl/abx500: prevent error path from corrupting returning error
pinctrl: sunxi: add of_xlate function
pinctrl/lantiq: fix pin number in ltq_pmx_gpio_request_enable
pinctrl/lantiq: add functionality to falcon_pinconf_dbg_show
pinctrl/lantiq: fix pinconfig parameters
pinctrl/lantiq: one of the boot leds was defined incorrectly
pinctrl/lantiq: only probe available pad controllers
...
Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.
In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add irqdomains for max8925's main irq, wrap irq register operations
into irqdomain's map func. it is necessary for dt support.
Also, add dt support for max8925 driver.
Signed-off-by: Qing Xu <qingx@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Support new model RTS5227.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
devm_* functions are device managed and make error handling
and code simpler; it also fix error exit paths
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add definition of watchdog IDs to be used by ux500_wdt driver.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the MICBIAS voltages and other attributes to be configured by the
platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Palmas register set is divided into different blocks (base and offset)
and hence different i2c addresses. The i2c address offsets are derived
from base address of block of registers.
Add inline APIs to access the Palma's registers which takes the base of
register block and register offset. The i2c address offset is derived
from the base address of register blocks.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch use delayed workqueue to check cable state after a certain
time. If extcon-max8997 driver check cable state during booting of
platform, this couldn't send the correct notification of cable state
to extcon consumer. Alwasys, this driver should check cable state
after the completion of platform initialization
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch set default H/W line path according to platfomr data.
The MAX8997 MUIC device can possibly set UART/USB or UART_AUX
/USB_AUX to internal H/W line path of MUIC device. Namely, only
one H/W line is used for two operation.
For example,
if H/W line path of MAX8997 device set UART/USB, micro usb cable
is connected to AP(Application Processor) and if H/W line path
set UART_AUX/USB_AUX, micro usb cable is connected to CP(Coprocessor).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch make max8997_muic_get_cable_type() function to remove
duplicate code for checking ADC/Charger cable type because almost
internal function need to read adc/chg_type value of MUIC register.
Also, remove *_detach() function, extcon-max8997 driver treat
attach/detach operation of cable in max8997_*_handler() function.
Lastly, this patch move defined constant in header file(include/
linux/mfd/max8997.h, max8997-private.h) because defined constant
is only used in the 'extcon-max8997.c'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch set default of ADC Debounce Time(25ms) during probe step.
Also, can possible change ADC Debounce Time according to H/W situation
by using max8997_set_adc_debounce_time()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch move defined constants to header file(max77693-private.h)
because of mask/unmask selectively interrupt of MUIC device according
to attribute of H/W board.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
When trying to get rid of the cross-includes of <mach/id.h>
from different drivers, so we can localize ASIC/CPU detection
to the mach-ux500 folder, we run into the way the PRCMU
handles base addresses and firmware detection.
This patch updates the firmware version detection to pass
the required information as platform data instead of
relying on cpu_is_* macros.
Now the PRCMU base address, the secondary TCDM area, the
TCPM area and the IRQ are passed as resources instead of
being grabbed from <mach/*> files. Incidentally this also
removes part of the reliance on <mach/irqs.h>.
Further it updates the firmware version detection, since the
location of the firmware ID bytes in the designated memory
are is now passed from the platform data instead. There is
no reason not to include the nice split-off of a struct to
hold the firmware information and a separate function to
populate it.
The patch actually rids the need to use the external
db8500_prcmu_early_init call at all, but I'm keepin back
that removal as I don't want the patch to be too big.
Cc: arm@kernel.org
Cc: Michel Jaoen <michel.jaouen@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Loic Pallardy <loic.pallardy@stericsson.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AB8500 GPIO no longer handles its GPIO IRQs. Instead, the AB8500
core driver has taken back the responsibility. Prior to this
happening, the AB8500 GPIO driver provided a set of virtual IRQs
which were used as a pass-through. These virtual IRQs had a base
of MOP500_AB8500_VIR_GPIO_IRQ_BASE, which was passed though pdata.
We don't need to do this anymore, so we're pulling out the
property from the structure.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds an entry in debugfs to check number of interrupts
from the AB.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Implement an API so that a user may dump all AB8500 registers
via debugfs file access.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Some drivers can detect subsystem failures e.g. shared memory driver
can detect modem sub system failures. It would be helpful in analyzing
these failures if AB register dump is available at that point. This
patch adds the API for the drivers to dump AB registers in the kernel
log.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Add the possibility to pass configuration settings for
SysCl1kReqRfClkBuf to SysClk8ReqRfClkBuf via platform data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kennet Wallden <kennet.wallden@stericsson.com>
Reviewed-by: Karl-Johan PERNTZ <karl-johan.perntz@stericsson.com>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
The kernel allows us to specify a function call-back which will be
invoked when a system power-off request has been received. Here we
provide one which is to be used when shutting down AB8500 based
platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the AB8500 register map with defines for a few
new chip variants and adds version detection helpers to handle
the different variants.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes the file <mach/id.h> from the global kernel include
scope, making it a pure mach-ux500 detail. All ASIC specifics
needed by drivers shall henceforth be passed from either platform
data or the device tree.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These static inlines are duplicating the task now done by the
Nomadik pinctrl drivers, so delete them from the prcmu static
inlines, also delete the register definitions as these should
only be known by the pinctrl driver.
Cc: Loic Pallardy <loic.pallardy@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Michel Jaouen <michel.jaouen@st.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
None of the aforementioned components have their own dedicated
platform data structures anymore. Instead they have all been
merged into one big Battery Management container. Let's remove
them and place all the nice newly added attributes into the core
container.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Do not touch the VBUSOVV in USBCHTRL2 when running on AB8505.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
AB and PMxxx doesn't have same watchdog refresh period. Add watchdog
to refresh period parameters in x500 charger structure, this should
kick watchdog every 30sec. The AC charging should also kick both
pm2xxx and the AB charger watchdog.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Add AB9540 and AB8505 support to ABx500 BTEMP driver.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
AC charger driver for the DB9540 based platforms.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Place a cap on the number of channels clocks are generated for. This is
intended for use with systems which have the WM5102 master an I2S bus with
multiple data lines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Travel and Carkit adapter should be handled directly by
the charger driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Ignore the low btemp interrupts for ab8500 3.0 and 3.3
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Today the battery recharge is determined with a voltage threshold. This
voltage threshold is only valid when the battery is relaxed. In charging
algorithm the voltage read is the loaded battery voltage and no
compensation is done to get the relaxed voltage. When maintenance
charging is not selected, this makes the recharging condition to almost
immediately activate when there is a discharge present on the battery.
Depending on which vendor the battery comes from this behavior can wear
out the battery much faster than normal.
The fuelgauge driver is responsible to monitor the actual battery
capacity and is able to estimate the remaining capacity. It is better to
use the remaining capacity as a limit to determine when battery should
be recharged.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
When enabling the CCEOC irq we might get false interrupt
from ab8500-driver due to the latched value will be saved
and interpreted as an IRQ when enabled
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Henrik Solver <henrik.solver@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch determine default uart/usb path by using platform data.
The MAX77693 MUIC device can possibliy set USB/UART/AUDIO/USB_AUX
/UART_AUX to internal h/w path of MUIC device. So, drvier should
determine default uart/usb path.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch check the state/type of cable after completing the initialization
of platform and notify platform of cable state/type through extcon. If extcon
provider driver notify the state/type of cable before completing platform boot,
this uevent is unused and ignored.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch make max77693-muic_get_cable_type() function to remove
duplicate code because almost internal function need to read
adc/adc1k/adclow/chg_type value of MUIC register. Also, this patch
add description of internal function move field constant of muic device
from extcon-max77693 driver to max77693 header file because of it
is needed for masking some interrupt through platform data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace the
proprietary Nokia BME stack;
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks to
Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers;
- Random fixups and enhancements for a bunch of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Bb5O
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
A fairly quiet release again, a couple of relatively small new features
and a bunch of driver specific work including yet more code elimination
and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM vexpress.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2d65
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release again, a couple of relatively small new
features and a bunch of driver specific work including yet more code
elimination and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM
vexpress."
Fix up trivial conflict (due to typo fix) in palmas-regulator.c
* tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (80 commits)
regulator: core: Fix logic to determinate if regulator can change voltage
regulator: s5m8767: Fix to work even if no DVS gpio present
regulator: s5m8767: Fix to read the first DVS register.
regulator: s5m8767: Fix to work when platform registers less regulators
regulator: gpio-regulator: gpio_set_value should use cansleep
regulator: gpio-regulator: Fix logical error in for() loop
regulator: anatop: Use regulator_[get|set]_voltage_sel_regmap
regulator: anatop: Use linear_min_sel with linear mapping
regulator: max1586: Implement get_voltage_sel callback
regulator: lp8788-buck: Kill _gpio_request function
regulator: tps80031: Convert tps80031_ldo_ops to linear_min_sel and list_voltage_linear
regulator: lp8788-ldo: Remove val array in lp8788_config_ldo_enable_mode
regulator: gpio-regulator: Add ifdef CONFIG_OF guard for regulator_gpio_of_match
regulator: palmas: Convert palmas_ops_smps to regulator_[get|set]_voltage_sel_regmap
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
regulators: add regulator_can_change_voltage() function
regulator: tps51632: Ensure [base|max]_voltage_uV pdata settings are valid
regulator: wm831x-dcdc: Add MODULE_ALIAS for wm831x-boostp
regulator: wm831x-dcdc: Ensure selected voltage falls within requested range
regulator: tps51632: Use linear_min_sel and regulator_[map|list]_voltage_linear
...
This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQyYh9AAoJEGwxgFQ9KSmk95UP+wcVXRynWulCVwEnVjjWv/UM
2fIsD0RkWO4WoqEVCNCHzW27pvFC36uqLx5vtas4CoJ2CX8ufQsPqWTx6K3MY/DQ
/VJT8CI2EKPQY1Q0PySVo2nBqwcUXWWoZE47t1ZowR6cxtmgrS8lLxYJvkbfEOHF
PS8WItACqH5F5VPxGFkhPwR2OTLfaYt7ilKx82vgxSzdMAel8q/I9uS/MUv8KV+1
1s5yBvlW5eyDXKpQbP/KiMJLJ/zk1MRAKK2HftAk8pNt+Xy160NvXhbILDWKC4uT
QBRPqyIe8BmL3VlXpw3mn7nbeU7rSfc/Rbrnm2+Yb54/Wtj4PnV6Z6bg7HO610im
e/tBNHoaL7qn1iNYSC3heW11rToksd03/LK0GREvkX3Bl21T+Naaun/DY/PGIfMQ
nOXy7uVo6sVdZnN2MTWof9qeMYBSlrwQVsMde6kbYadNcXnuqUqCOx41kiAdE8t5
jfZy5QR+uDjdJgDv8/CuiCYxSjjTUfO1tdSV/VjsTK17Gfw3DWTJpeznVnoIALbZ
81HXYxb+uGZ8xDr0WXGkydlnPvB6bnWu2vvfrLBkioA/p60EDNCtgKo1y3NzQGh8
P2qILNhXIRrS2EoAScQOb6F1RPsvbDN9PbihnkShX3r7DXyeynr9jgPy3L2vf0bR
xyu0jtQiqYb34ss7qqdz
=IIsz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Here is the "big" char/misc driver patches for 3.8-rc1. I'm starting to
put random driver subsystems that I had previously sent you through the
driver-core tree in this tree, as it makes more sense to do so.
Nothing major here, the various __dev* removals, some mei driver
updates, and other random driver-specific things from the different
maintainers and developers.
Note, some MFD drivers got added through this tree, and they are also
coming in through the "real" MFD tree as well, due to some major
mis-communication between me and the different developers. If you have
any merge conflicts, take the ones from the MFD tree, not these ones,
sorry about that.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHj7AACgkQMUfUDdst+ym7pQCgxhFDGQRJimG+Ddag+ghfLhQh
Ql0AoJsWVFvQjb7q1NO7OvOABaxjEJdu
=na5b
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver patches for 3.8-rc1. I'm starting
to put random driver subsystems that I had previously sent you through
the driver-core tree in this tree, as it makes more sense to do so.
Nothing major here, the various __dev* removals, some mei driver
updates, and other random driver-specific things from the different
maintainers and developers.
Note, some MFD drivers got added through this tree, and they are also
coming in through the "real" MFD tree as well, due to some major
mis-communication between me and the different developers. If you
have any merge conflicts, take the ones from the MFD tree, not these
ones, sorry about that.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflict in drivers/mmc/host/Kconfig due to new drivers
having been added (both at the end, as usual..)
* tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (84 commits)
MAINTAINERS: remove drivers/staging/hv/
misc/st_kim: Free resources in the error path of probe()
drivers/char: for hpet, add count checking, and ~0UL instead of -1
w1-gpio: Simplify & get rid of defines
w1-gpio: Pinctrl-fy
extcon: remove use of __devexit_p
extcon: remove use of __devinit
extcon: remove use of __devexit
drivers: uio: Only allocate new private data when probing device tree node
drivers: uio_dmem_genirq: Allow partial success when opening device
drivers: uio_dmem_genirq: Don't use DMA_ERROR_CODE to indicate unmapped regions
drivers: uio_dmem_genirq: Don't mix address spaces for dynamic region vaddr
uio: remove use of __devexit
uio: remove use of __devinitdata
uio: remove use of __devinit
uio: remove use of __devexit_p
char: remove use of __devexit
char: remove use of __devinitconst
char: remove use of __devinitdata
char: remove use of __devinit
...
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
Mark Brown