This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.
The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.
The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.
One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.
The first value current_itr represents the current value of the register.
The second value target_itr represents the desired value of the register.
The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While testing code for the recent ITR changes I found that updating the Tx
ITR appeared to have no effect with everything defaulting to the Rx ITR. A
bit of digging narrowed it down the fact that we were asking the PF to
associate all causes with ITR 0 as we weren't populating the itr_idx values
for either Rx or Tx.
To correct it I have added the configuration for these values to this
patch. In addition I did some minor clean-up to just add a local pointer
for the vector map instead of dereferencing it based off of the index
repeatedly. In my opinion this makes the resultant code a bit more readable
and saves us a few characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.
This helps to make the code more readable as we can quickly translate from
one value to the other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The CLEARPBA bit in the dynamic interrupt control register actually has
no effect either way on the hardware. As per errata 28 in the XL710
specification update the interrupt is actually cleared any time the
register is written with the INTENA_MSK bit set to 0. As such the act of
toggling the enable bit actually will trigger the interrupt being
cleared and could lead to potential lost events if auto-masking is
not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a further clean-up related to the change over to using
q_vector->reg_idx when accessing the ITR registers. Specifically the code
appears to have several other spots where we were computing the register
offset manually and this resulted in errors in a few spots.
Specifically in the i40evf functions for mapping queues to vectors it
appears we may have had an off by 1 error since (v_idx - 1) for the first
q_vector with an index of 0 would result in us returning -1 if I am not
mistaken.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in i40e_set_priv_flags we use new_flags to check for the
I40E_FLAG_DISABLE_FW_LLDP flag. This is an issue for a few a reasons.
DISABLE_FW_LLDP is persistent across reboots/driver reloads. This means
we need some way to detect if FW LLDP is enabled on init. We do this by
trying to init_dcb and if it fails with EPERM we know LLDP is disabled
in FW.
This could be a problem on older FW versions or NPAR enabled PFs because
there are situations where the FW could disable LLDP, but they do _not_
support using this flag to change it. If we do end up in this
situation, the flag will be set, then when the user tries to change any
priv flags, the driver thinks the user is trying to disable FW LLDP on a
FW that doesn't support it and essentially forbids any priv flag
changes.
The fix is simple, instead of checking if this flag is set, we should be
checking if the user is trying to _change_ the flag on unsupported FW
versions.
This patch also adds a comment explaining that the cmpxchg is the point
of no return. Once we put the new flags into pf->flags we can't back
out.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a warning message when the link-down-on-close flag is
setting on. The warning is printed only on MFP devices
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic for dynamic ITR update is confusing at best as there were odd
paths chosen for how to find the rings associated with a given queue based
on the vector index and other inconsistencies throughout the code.
This patch is an attempt to clean up the logic so that we can more easily
understand what is going on. Specifically if there is a Rx or Tx ring that
is enabled in dynamic mode on the q_vector it is allowed to override the
other side of the interrupt moderation. While it isn't correct all this
patch is doing is cleaning up the logic for now so that when we come
through and fix it we can more easily identify that this is wrong.
The other big change made here is that we replace references to:
vsi->rx_rings[q_vector->v_idx]->itr_setting
with:
q_vector->rx.ring->itr_setting
The general idea is we can avoid the long pointer chase since just
accessing q_vector->rx.ring is a single pointer access versus having to
chase down vsi->rx_rings, and then finding the pointer in the array, and
finally chasing down the itr_setting from there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'bufer' should be 'buffer'
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jy5l
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
Pull misc vfs fixes from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
seq_file: fix incomplete reset on read from zero offset
kernfs: fix regression in kernfs_fop_write caused by wrong type
This function returns realloc'ed memory, so the returned pointer
must be passed to free() when done. So, 'const' qualifier is odd.
It is allowed to modify the expanded string.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We already have xmalloc(), xcalloc(). Add xrealloc() as well
to save tedious error handling.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
Hightlights include:
Stable fixes:
- Fix an incorrect calculation of the RDMA send scatter gather element limit
- Fix an Oops when attempting to free resources after RDMA device removal
Bugfixes:
- SUNRPC: Ensure we always release the TCP socket in a timely fashion when
the connection is shut down.
- SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
Latency/Performance:
- SUNRPC: Queue latency sensitive socket tasks to the less contended
xprtiod queue
- SUNRPC: Make the xprtiod workqueue unbounded.
- SUNRPC: Make the rpciod workqueue unbounded
-----BEGIN PGP SIGNATURE-----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=KST7
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"A few bugfixes and some small sunrpc latency/performance improvements
before the merge window closes:
Stable fixes:
- fix an incorrect calculation of the RDMA send scatter gather
element limit
- fix an Oops when attempting to free resources after RDMA device
removal
Bugfixes:
- SUNRPC: Ensure we always release the TCP socket in a timely fashion
when the connection is shut down.
- SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
Latency/Performance:
- SUNRPC: Queue latency sensitive socket tasks to the less contended
xprtiod queue
- SUNRPC: Make the xprtiod workqueue unbounded.
- SUNRPC: Make the rpciod workqueue unbounded"
* tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
fix parallelism for rpc tasks
Make the xprtiod workqueue unbounded.
SUNRPC: Queue latency-sensitive socket tasks to xprtiod
SUNRPC: Ensure we always close the socket after a connection shuts down
xprtrdma: Fix BUG after a device removal
xprtrdma: Fix calculation of ri_max_send_sges
Pull SCSI target updates from Nicholas Bellinger:
"The highlights include:
- numerous target-core-user improvements related to queue full and
timeout handling. (MNC)
- prevent target-core-user corruption when invalid data page is
requested. (MNC)
- add target-core device action configfs attributes to allow
user-space to trigger events separate from existing attributes
exposed to end-users. (MNC)
- fix iscsi-target NULL pointer dereference 4.6+ regression in CHAP
error path. (David Disseldorp)
- avoid target-core backend UNMAP callbacks if range is zero. (Andrei
Vagin)
- fix a iscsi-target 4.14+ regression related multiple PDU logins,
that was exposed due to removal of TCP prequeue support. (Florian
Westphal + MNC)
Also, there is a iser-target bug still being worked on for post -rc1
code to address a long standing issue resulting in persistent
ib_post_send() failures, for RNICs with small max_send_sge"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
iscsi-target: make sure to wake up sleeping login worker
tcmu: Fix trailing semicolon
tcmu: fix cmd user after free
target: fix destroy device in target_configure_device
tcmu: allow userspace to reset ring
target core: add device action configfs files
tcmu: fix error return code in tcmu_configure_device()
target_core_user: add cmd id to broken ring message
target: add SAM_STAT_BUSY sense reason
tcmu: prevent corruption when invalid data page requested
target: don't call an unmap callback if a range length is zero
target/iscsi: avoid NULL dereference in CHAP auth error path
cxgbit: call neigh_event_send() to update MAC address
target: tcm_loop: Use seq_puts() in tcm_loop_show_info()
target: tcm_loop: Delete an unnecessary return statement in tcm_loop_submission_work()
target: tcm_loop: Delete two unnecessary variable initialisations in tcm_loop_issue_tmr()
target: tcm_loop: Combine substrings for 26 messages
target: tcm_loop: Improve a size determination in two functions
target: tcm_loop: Delete an error message for a failed memory allocation in four functions
sbp-target: Delete an error message for a failed memory allocation in three functions
...
as well as the removing of function probes.
This fixes the code with Al's suggestions. I also added a few selftests
to test the broken cases such that they wont happen again.
-----BEGIN PGP SIGNATURE-----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=tVDz
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Al Viro discovered some breakage with the parsing of the
set_ftrace_filter as well as the removing of function probes.
This fixes the code with Al's suggestions. I also added a few
selftests to test the broken cases such that they wont happen
again"
* tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Add more tests for removing of function probes
selftests/ftrace: Add some missing glob checks
selftests/ftrace: Have reset_ftrace_filter handle multiple instances
selftests/ftrace: Have reset_ftrace_filter handle modules
tracing: Fix parsing of globs with a wildcard at the beginning
ftrace: Remove incorrect setting of glob search field
-----BEGIN PGP SIGNATURE-----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=Ps35
-----END PGP SIGNATURE-----
Merge tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"There are a couple additional security fixes that are still being
tested that are not in this set."
* tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
Add missing structs and defines from recent SMB3.1.1 documentation
address lock imbalance warnings in smbdirect.c
cifs: silence compiler warnings showing up with gcc-8.0.0
Add some missing debug fields in server and tcon structs
Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two issues in the reuseport_bpf selftests that were
reported by Linaro CI:
[...]
+ ./reuseport_bpf
---- IPv4 UDP ----
Testing EBPF mod 10...
Reprograming, testing mod 5...
./reuseport_bpf: ebpf error. log:
0: (bf) r6 = r1
1: (20) r0 = *(u32 *)skb[0]
2: (97) r0 %= 10
3: (95) exit
processed 4 insns
: Operation not permitted
+ echo FAIL
[...]
---- IPv4 TCP ----
Testing EBPF mod 10...
./reuseport_bpf: failed to bind send socket: Address already in use
+ echo FAIL
[...]
For the former adjust rlimit since this was the cause of
failure for loading the BPF prog, and for the latter add
SO_REUSEADDR.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3502
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SCTP makes INIT or INIT_ACK packet the total chunk length
can exceed SCTP_MAX_CHUNK_LEN which leads to kernel panic when
transmitting these packets, e.g. the crash on sending INIT_ACK:
[ 597.804948] skbuff: skb_over_panic: text:00000000ffae06e4 len:120168
put:120156 head:000000007aa47635 data:00000000d991c2de
tail:0x1d640 end:0xfec0 dev:<NULL>
...
[ 597.976970] ------------[ cut here ]------------
[ 598.033408] kernel BUG at net/core/skbuff.c:104!
[ 600.314841] Call Trace:
[ 600.345829] <IRQ>
[ 600.371639] ? sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.436934] skb_put+0x16c/0x200
[ 600.477295] sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.540630] ? sctp_packet_config+0x890/0x890 [sctp]
[ 600.601781] ? __sctp_packet_append_chunk+0x3b4/0xd00 [sctp]
[ 600.671356] ? sctp_cmp_addr_exact+0x3f/0x90 [sctp]
[ 600.731482] sctp_outq_flush+0x663/0x30d0 [sctp]
[ 600.788565] ? sctp_make_init+0xbf0/0xbf0 [sctp]
[ 600.845555] ? sctp_check_transmitted+0x18f0/0x18f0 [sctp]
[ 600.912945] ? sctp_outq_tail+0x631/0x9d0 [sctp]
[ 600.969936] sctp_cmd_interpreter.isra.22+0x3be1/0x5cb0 [sctp]
[ 601.041593] ? sctp_sf_do_5_1B_init+0x85f/0xc30 [sctp]
[ 601.104837] ? sctp_generate_t1_cookie_event+0x20/0x20 [sctp]
[ 601.175436] ? sctp_eat_data+0x1710/0x1710 [sctp]
[ 601.233575] sctp_do_sm+0x182/0x560 [sctp]
[ 601.284328] ? sctp_has_association+0x70/0x70 [sctp]
[ 601.345586] ? sctp_rcv+0xef4/0x32f0 [sctp]
[ 601.397478] ? sctp6_rcv+0xa/0x20 [sctp]
...
Here the chunk size for INIT_ACK packet becomes too big, mostly
because of the state cookie (INIT packet has large size with
many address parameters), plus additional server parameters.
Later this chunk causes the panic in skb_put_data():
skb_packet_transmit()
sctp_packet_pack()
skb_put_data(nskb, chunk->skb->data, chunk->skb->len);
'nskb' (head skb) was previously allocated with packet->size
from u16 'chunk->chunk_hdr->length'.
As suggested by Marcelo we should check the chunk's length in
_sctp_make_chunk() before trying to allocate skb for it and
discard a chunk if its size bigger than SCTP_MAX_CHUNK_LEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leinter@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-02-09
please apply the following two qeth patches for 4.16 and stable.
One restricts a command quirk to the intended commandd type,
while the other fixes an off-by-one during data transmission
that can cause qeth to build malformed buffer descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes: 5b54e16f1a ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a memory range/skb where the last byte falls onto a page boundary
(ie. 'end' is of the form xxx...xxx001), the PFN_UP() part of the
calculation currently doesn't round up to the next PFN due to an
off-by-one error.
Thus qeth believes that the skb occupies one page less than it
actually does, and may select a IO buffer that doesn't have enough spare
buffer elements to fit all of the skb's data.
HW detects this as a malformed buffer descriptor, and raises an
exception which then triggers device recovery.
Fixes: 2863c61334 ("qeth: refactor calculation of SBALE count")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch switch to use kvmalloc_array() for using a vmalloc()
fallback to help in case kmalloc() fails.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes: 2e0ab8ca83 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid slab to warn about exceeded size, fail early if queue
occupies more than KMALLOC_MAX_SIZE.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes: 2e0ab8ca83 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel says:
====================
stmmac irq fixes/cleanups
A couple of small stmmac irq fixes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.
For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.
Improve code readability by removing this redundant code.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit 0a764db103 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit 0a764db103 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating RX or TX buffer pools, the driver needs to provide a
unique mapping ID to firmware for each pool. This value is assigned
using a counter which is incremented after a new pool is created. The
ID can be an integer ranging from 1-255. When migrating to a device
that requests a different number of queues, this value was not being
reset properly. As a result, after enough migrations, the counter
exceeded the upper bound and pool creation failed. This is fixed by
resetting the counter to one in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJafa95AAoJELDendYovxMvz8oH+QGgM0ZN0YfJa2JuR/RAlYyn
3OfSlMbGOjlmT74C1Rcx+SHNbbxUunoAx70UnvLbgtzbYyX08yVNsfNFesrarAkr
dkBBsAdLLzZYOoKnSKHWGl8Cf26F5eJbLo1FSSNYzmCaz0oD+geOqIWnOQMHkuUW
Rv6En9SjgzrE6dvzQ/LNtpjqFnSwJ+cD8ZkI21YXyDmZ3/xvZ9h8ID5vrzlP4wVH
gENxAMxn9w0nlbtHLvc2KGbVOUTSsA1LxbjDqzBEIGqgKmZVdt6d1J0KfO3eM6ej
9JuPcRt34HFPifuwI6xgtcKJjEr7QptIiDiSVvifXMvQnqfGc2b+qOFLhY6XwOU=
=+zOt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Only five small fixes for issues when running under Xen"
* tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix {set,clear}_foreign_p2m_mapping on autotranslating guests
pvcalls-back: do not return error on inet_accept EAGAIN
xen-netfront: Fix race between device setup and open
xen/grant-table: Use put_page instead of free_page
x86/xen: init %gs very early to avoid page faults with stack protector
Pull s390 updates from Heiko Carstens:
"The main thing in this merge is the defense for the Spectre
vulnerabilities. But there are other updates as well, the changes in
more detail:
- An s390 specific implementation of the array_index_mask_nospec
function to the defense against spectre v1
- Two patches to utilize the new PPA-12/PPA-13 instructions to run
the kernel and/or user space with reduced branch predicton.
- The s390 variant of the 'retpoline' spectre v2 defense called
'expoline'. There is no return instruction for s390, instead an
indirect branch is used for function return
The s390 defense mechanism for indirect branches works by using an
execute-type instruction with the indirect branch as the target of
the execute. In effect that turns off the prediction for the
indirect branch.
- Scrub registers in entry.S that contain user controlled values to
prevent the speculative use of these values.
- Re-add the second parameter for the s390 specific runtime
instrumentation system call and move the header file to uapi. The
second parameter will continue to do nothing but older kernel
versions only accepted valid real-time signal numbers. The details
will be documented in the man-page for the system call.
- Corrections and improvements for the s390 specific documentation
- Add a line to /proc/sysinfo to display the CPU model dependent
license-internal-code identifier
- A header file include fix for eadm.
- An error message fix in the kprobes code.
- The removal of an outdated ARCH_xxx select statement"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kconfig: Remove ARCH_WANTS_PROT_NUMA_PROT_NONE select
s390: introduce execute-trampolines for branches
s390: run user space and KVM guests with modified branch prediction
s390: add options to change branch prediction behaviour for the kernel
s390/alternative: use a copy of the facility bit mask
s390: add optimized array_index_mask_nospec
s390: scrub registers on kernel entry and KVM exit
s390/cio: fix kernel-doc usage
s390/runtime_instrumentation: re-add signum system call parameter
s390/cpum_cf: correct counter number of LAST_HOST_TRANSLATIONS
s390/kprobes: Fix %p uses in error messages
s390/runtime instrumentation: provide uapi header file
s390/sysinfo: add and display licensed internal code identifier
s390/docs: reword airq section
s390/docs: mention subchannel types
s390/cmf: fix kerneldoc
s390/eadm: fix CONFIG_BLOCK include dependency
- Update the ACPICA kernel code to upstream revision 20180105 including:
* Assorted fixes (Jung-uk Kim).
* Support for X32 ABI compilation (Anuj Mittal).
* Update of ACPICA copyrights to 2018 (Bob Moore).
- Prepare for future modifications to avoid executing the _STA control
method too early (Hans de Goede).
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam).
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang).
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530
(Kai Heng Feng).
- Address static checker warnings in the CPPC code (Gustavo Silva).
- Avoid printing a raw pointer to the kernel log in the smart
battery driver (Greg Kroah-Hartman).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rVdp
-----END PGP SIGNATURE-----
Merge tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups, a few new quirks, a couple of
updates related to the handling of ACPI tables and ACPICA copyrights
refreshment.
Specifics:
- Update the ACPICA kernel code to upstream revision 20180105
including:
* Assorted fixes (Jung-uk Kim)
* Support for X32 ABI compilation (Anuj Mittal)
* Update of ACPICA copyrights to 2018 (Bob Moore)
- Prepare for future modifications to avoid executing the _STA
control method too early (Hans de Goede)
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam)
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang)
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
Heng Feng)
- Address static checker warnings in the CPPC code (Gustavo Silva)
- Avoid printing a raw pointer to the kernel log in the smart battery
driver (Greg Kroah-Hartman)"
* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sbshc: remove raw pointer from printk() message
ACPI: SPCR: Make SPCR available to x86
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
ACPI / tables: Add IORT to injectable table list
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPICA: Update version to 20180105
ACPICA: All acpica: Update copyrights to 2018
ACPI / processor: Set default C1 idle state description
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
ACPI: processor_perflib: Do not send _PPC change notification if not ready
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
ACPI / video: Use true for boolean value
- Drop the at32ap-cpufreq driver which is useless after the
removal of the corresponding arch (Corentin LABBE).
- Fix a regression from the 4.14 cycle in the APM idle driver by
making it initialize the polling state properly (Rafael Wysocki).
- Fix a crash on failing system suspend due to a missing check in
the cpufreq core (Bo Yan).
- Make the intel_pstate driver initialize the hardware-managed
P-state control (HWP) feature on CPU0 upon resume from system
suspend if HWP had been enabled before the system was suspended
(Chen Yu).
- Fix up the SCPI cpufreq driver after recent changes (Sudeep Holla,
Wei Yongjun).
- Avoid pointer subtractions during frequency table walks in cpufreq
(Dominik Brodowski).
- Avoid the check for ProcFeedback in ST/CZ in the cpufreq driver
for AMD processors and add a MODULE_ALIAS for cpufreq on ARM IMX
(Akshu Agrawal, Nicolas Chauvet).
- Fix the prototype of swsusp_arch_resume() on x86 (Arnd Bergmann).
- Fix up the parsing of power domains DT data (Ulf Hansson).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xKgy
-----END PGP SIGNATURE-----
Merge tag 'pm-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups and removal of the no longer
needed at32ap-cpufreq driver.
Specifics:
- Drop the at32ap-cpufreq driver which is useless after the removal
of the corresponding arch (Corentin LABBE).
- Fix a regression from the 4.14 cycle in the APM idle driver by
making it initialize the polling state properly (Rafael Wysocki).
- Fix a crash on failing system suspend due to a missing check in the
cpufreq core (Bo Yan).
- Make the intel_pstate driver initialize the hardware-managed
P-state control (HWP) feature on CPU0 upon resume from system
suspend if HWP had been enabled before the system was suspended
(Chen Yu).
- Fix up the SCPI cpufreq driver after recent changes (Sudeep Holla,
Wei Yongjun).
- Avoid pointer subtractions during frequency table walks in cpufreq
(Dominik Brodowski).
- Avoid the check for ProcFeedback in ST/CZ in the cpufreq driver for
AMD processors and add a MODULE_ALIAS for cpufreq on ARM IMX (Akshu
Agrawal, Nicolas Chauvet).
- Fix the prototype of swsusp_arch_resume() on x86 (Arnd Bergmann).
- Fix up the parsing of power domains DT data (Ulf Hansson)"
* tag 'pm-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
arm: imx: Add MODULE_ALIAS for cpufreq
cpufreq: Add and use cpufreq_for_each_{valid_,}entry_idx()
cpufreq: intel_pstate: Enable HWP during system resume on CPU0
cpufreq: scpi: fix error return code in scpi_cpufreq_init()
x86: hibernate: fix swsusp_arch_resume() prototype
PM / domains: Fix up domain-idle-states OF parsing
cpufreq: scpi: fix static checker warning cdev isn't an ERR_PTR
cpufreq: remove at32ap-cpufreq
cpufreq: AMD: Ignore the check for ProcFeedback in ST/CZ
x86: PM: Make APM idle driver initialize polling state
cpufreq: Skip cpufreq resume if it's not suspended
Calling __UDPX_INC_STATS() from a preemptible context leads to a
warning of the form:
BUG: using __this_cpu_add() in preemptible [00000000] code: kworker/u5:0/31
caller is xs_udp_data_receive_workfn+0x194/0x270
CPU: 1 PID: 31 Comm: kworker/u5:0 Not tainted 4.15.0-rc8-00076-g90ea9f1 #2
Workqueue: xprtiod xs_udp_data_receive_workfn
Call Trace:
dump_stack+0x85/0xc1
check_preemption_disabled+0xce/0xe0
xs_udp_data_receive_workfn+0x194/0x270
process_one_work+0x318/0x620
worker_thread+0x20a/0x390
? process_one_work+0x620/0x620
kthread+0x120/0x130
? __kthread_bind_mask+0x60/0x60
ret_from_fork+0x24/0x30
Since we're taking a spinlock in those functions anyway, let's fix the
issue by moving the call so that it occurs under the spinlock.
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The omapfb driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it
relies on the <linux/pinctrl/consumer.h> and <linux/seq_file.h>
being pulled in by the <linux/device.h> header implicitly.
Include these headers explicitly to avoid the build failures.
Fixes: 23c35f48f5 ("pinctrl: remove include file from <linux/device.h>")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
[b.zolnierkie: fix include order and patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Jesper Dangaard Brouer says:
====================
While playing with using libbpf for the Suricata project, we had
issues LLVM >= 4.0.1 generating ELF files that could not be loaded
with libbpf (tools/lib/bpf/).
During the troubleshooting phase, I wrote a test program and improved
the debugging output in libbpf. I turned this into a selftests
program, and it also serves as a code example for libbpf in itself.
I discovered that there are at least three ELF load issues with
libbpf. I left them as TODO comments in (tools/testing/selftests/bpf)
test_libbpf.sh. I've only fixed the load issue with eh_frames, and
other types of relo-section that does not have exec flags. We can
work on the other issues later.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
V3: More generic skipping of relo-section (suggested by Daniel)
If clang >= 4.0.1 is missing the option '-target bpf', it will cause
llc/llvm to create two ELF sections for "Exception Frames", with
section names '.eh_frame' and '.rel.eh_frame'.
The BPF ELF loader library libbpf fails when loading files with these
sections. The other in-kernel BPF ELF loader in samples/bpf/bpf_load.c,
handle this gracefully. And iproute2 loader also seems to work with these
"eh" sections.
The issue in libbpf is caused by bpf_object__elf_collect() skipping
some sections, and later when performing relocation it will be
pointing to a skipped section, as these sections cannot be found by
bpf_object__find_prog_by_idx() in bpf_object__collect_reloc().
This is a general issue that also occurs for other sections, like
debug sections which are also skipped and can have relo section.
As suggested by Daniel. To avoid keeping state about all skipped
sections, instead perform a direct qlookup in the ELF object. Lookup
the section that the relo-section points to and check if it contains
executable machine instructions (denoted by the sh_flags
SHF_EXECINSTR). Use this check to also skip irrelevant relo-sections.
Note, for samples/bpf/ the '-target bpf' parameter to clang cannot be used
due to incompatibility with asm embedded headers, that some of the samples
include. This is explained in more details by Yonghong Song in bpf_devel_QA.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This script test_libbpf.sh will be part of the 'make run_tests'
invocation, but can also be invoked manually in this directory,
and a verbose mode can be enabled via setting the environment
variable $VERBOSE like:
$ VERBOSE=yes ./test_libbpf.sh
The script contains some tests that are commented out, as they
currently fail. They are reminders about what we need to improve
for the libbpf loader library.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
V2: Moved program into selftests/bpf from tools/libbpf
This program can be used on its own for testing/debugging if a
BPF ELF-object file can be loaded with libbpf (from tools/lib/bpf).
If something is wrong with the ELF object, the program have
a --debug mode that will display the ELF sections and especially
the skipped sections. This allows for quickly identifying the
problematic ELF section number, which can be corrolated with the
readelf tool.
The program signal error via return codes, and also have
a --quiet mode, which is practical for use in scripts like
selftests/bpf.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
While debugging a bpf ELF loading issue, I needed to correlate the
ELF section number with the failed relocation section reference.
Thus, add section numbers/index to the pr_debug.
In debug mode, also print section that were skipped. This helped
me identify that a section (.eh_frame) was skipped, and this was
the reason the relocation section (.rel.eh_frame) could not find
that section number.
The section numbers corresponds to the readelf tools Section Headers [Nr].
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
I recently fixed up a lot of commits that forgot to keep the tooling
headers in sync. And then I forgot to do the same thing in commit
cb5f7334d4 ("bpf: add comments to BPF ld/ldx sizes"). Let correct
that before people notice ;-).
Lawrence did partly fix/sync this for bpf.h in commit d6d4f60c3a
("bpf: add selftest for tcpbpf").
Fixes: cb5f7334d4 ("bpf: add comments to BPF ld/ldx sizes")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
But it's also a fairly small update this time around. Some cleanup,
RDMA fixes, overlayfs fixes, and a fix for an NFSv4 state bug.
The bigger deal for nfsd this time around is Jeff Layton's
already-merged i_version patches. This series has a minor conflict with
that one, and the resolution should be obvious. (Stephen Rothwell has
been carrying it in linux-next for what it's worth.)
-----BEGIN PGP SIGNATURE-----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=icEX
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd update from Bruce Fields:
"A fairly small update this time around. Some cleanup, RDMA fixes,
overlayfs fixes, and a fix for an NFSv4 state bug.
The bigger deal for nfsd this time around was Jeff Layton's
already-merged i_version patches"
* tag 'nfsd-4.16' of git://linux-nfs.org/~bfields/linux:
svcrdma: Fix Read chunk round-up
NFSD: hide unused svcxdr_dupstr()
nfsd: store stat times in fill_pre_wcc() instead of inode times
nfsd: encode stat->mtime for getattr instead of inode->i_mtime
nfsd: return RESOURCE not GARBAGE_ARGS on too many ops
nfsd4: don't set lock stateid's sc_type to CLOSED
nfsd: Detect unhashed stids in nfsd4_verify_open_stid()
sunrpc: remove dead code in svc_sock_setbufsize
svcrdma: Post Receives in the Receive completion handler
nfsd4: permit layoutget of executable-only files
lockd: convert nlm_rqst.a_count from atomic_t to refcount_t
lockd: convert nlm_lockowner.count from atomic_t to refcount_t
lockd: convert nsm_handle.sm_count from atomic_t to refcount_t
Alexander Duyck