NPCM7XX_Tx_OPER GENMASK bits are wrong, fix them.
Hopefully the NPCM7XX_REG_TICR0 register reset value of those bits was 0,
so it did not cause an issue.
The function npcm7xx_timer_oneshot() reads the register
NPCM7XX_REG_TCSR0, modifies it and then reads it again overwriting the
previous changes. Remove the extra read which is pointless.
The function npcm7xx_timer_periodic() is correct but the code writes
to the NPCM7XX_REG_TICR0 register while it is dealing with the
NPCM7XX_REG_TCSR0 register, that is confusing. Separate the write to
the registers in the code for the sake of clarity.
Fixes: 1c00289ecd ("clocksource/drivers/npcm: Add NPCM7xx timer driver")
Signed-off-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use the DIV_ROUND_CLOSEST() helper instead of open-coding the same
operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The system counter block guide states that the base clock is
internally divided by 3 before use, that means the clock input of
system counter defined in DT should be base clock which is normally
from OSC, and then internally divided by 3 before use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Implement and register delay timer to allow get_cycles() to work properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The newer Allwinner SoCs have a High Speed Timer supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Newer Allwinner SoCs have different number of interrupts, let's add
different compatibles for all of them to deal with this properly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Newer Allwinner SoCs have different number of interrupts, let's add
different compatibles for all of them to deal with this properly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The older Allwinner SoCs have a Timer supported in Linux, with a matching
Device Tree binding.
While the original binding only mentions one interrupt, the timer actually
has 6 of them.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
There is no particular reason to not enable TSC page clocksource on
32-bit. mul_u64_u64_shr() is available and despite the increased
computational complexity (compared to 64bit) TSC page is still a huge win
compared to MSR-based clocksource.
In-kernel reads:
MSR based clocksource: 3361 cycles
TSC page clocksource: 49 cycles
Reads from userspace (utilizing vDSO in case of TSC page):
MSR based clocksource: 5664 cycles
TSC page clocksource: 131 cycles
Enabling TSC page on 32bits allows to get rid of CONFIG_HYPERV_TSCPAGE as
it is now not any different from CONFIG_HYPERV_TIMER.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lkml.kernel.org/r/20190822083630.17059-1-vkuznets@redhat.com
Hyper-V guests use the default native_sched_clock() in
pv_ops.time.sched_clock on x86. But native_sched_clock() directly uses the
raw TSC value, which can be discontinuous in a Hyper-V VM.
Add the generic hv_setup_sched_clock() to set the sched clock function
appropriately. On x86, this sets pv_ops.time.sched_clock to read the
Hyper-V reference TSC value that is scaled and adjusted to be continuous.
Also move the Hyper-V reference TSC initialization much earlier in the boot
process so no discontinuity is observed when pv_ops.time.sched_clock
calculates its offset.
[ tglx: Folded build fix ]
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lkml.kernel.org/r/20190814123216.32245-3-Tianyu.Lan@microsoft.com
Prepare to add Hyper-V sched clock callback and move Hyper-V Reference TSC
initialization much earlier in the boot process. Earlier initialization is
needed so that it happens while the timestamp value is still 0 and no
discontinuity in the timestamp will occur when pv_ops.time.sched_clock
calculates its offset.
The earlier initialization requires that the Hyper-V TSC page be allocated
statically instead of with vmalloc(), so fixup the references to the TSC
page and the method of getting its physical address.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190814123216.32245-2-Tianyu.Lan@microsoft.com
Warning when p == NULL and then proceeding and dereferencing p does not
make any sense as the kernel will crash with a NULL pointer dereference
right away.
Bailing out when p == NULL and returning an error code does not cure the
underlying problem which caused p to be NULL. Though it might allow to
do proper debugging.
Same applies to the clock id check in set_process_cpu_timer().
Clean them up and make them return without trying to do further damage.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190819143801.846497772@linutronix.de
migration_base is used as a placeholder when an hrtimer is migrated to a
different CPU. In the case that hrtimer_cancel_wait_running() hits a timer
which is currently migrated it would pointlessly acquire the expiry lock of
the migration base, which is even not initialized.
Surely it could be initialized, but there is absolutely no point in
acquiring this lock because the timer is guaranteed not to run it's
callback for which the caller waits to finish on that base. So it would
just do the inc/lock/dec/unlock dance for nothing.
As the base switch is short and non-preemptible, there is no issue when the
wait function returns immediately.
The timer base and base->cpu_base cannot be NULL in the code path which is
invoking that, so just replace those checks with a check whether base is
migration base.
[ tglx: Updated from RT patch. Massaged changelog. Added comment. ]
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190821092409.13225-4-julien.grall@arm.com
The update to timer->base is protected by the base->cpu_base->lock().
However, hrtimer_cancel_wait_running() does access it lockless. So the
compiler is allowed to refetch timer->base which can cause havoc when the
timer base is changed concurrently.
Use READ_ONCE() to prevent this.
[ tglx: Adapted from a RT patch ]
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190821092409.13225-2-julien.grall@arm.com
The comment above cleanup_timers() is outdated. The timers are only removed
from the task/process list heads but not modified in any other way.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190819143801.747233612@linutronix.de
rtc.h is not needed in alarmtimers when a forward declaration of struct
rtc_device is provided. That allows to include posix-timers.h without
adding more includes to alarmtimer.h or creating circular include
dependencies.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190819143801.565389536@linutronix.de
- Rename struct siginfo to kernel_siginfo as that is used and required
- Add a forward declaration for task_struct and remove sched.h include
- Remove timex.h include as it is not needed
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190819143801.472005793@linutronix.de
The handling of a priority inversion between timer cancelling and a a not
well defined possible preemption of softirq kthread is not very clear.
Especially in the posix timers side it's unclear why there is a specific RT
wait callback.
All the nice explanations can be found in the initial changelog of
f61eff83ce (hrtimer: Prepare support for PREEMPT_RT").
Extract the detailed informations from there and put it into comments.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190820132656.GC2093@lenoir
Posix timer delete retry loops are affected by the same priority inversion
and live lock issues as the other timers.
Provide a RT specific synchronization function which keeps a reference to
the timer by holding rcu read lock to prevent the timer from being freed,
dropping the timer lock and invoking the timer specific wait function via a
new callback.
This does not yet cover posix CPU timers because they need more special
treatment on PREEMPT_RT.
[ This is folded into the original attempt which did not use a callback. ]
Originally-by: Anna-Maria Gleixenr <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190819143801.656864506@linutronix.de
Timer deletion on PREEMPT_RT is prone to priority inversion and live
locks. The hrtimer code has a synchronization mechanism for this. Posix CPU
timers will grow one.
But that mechanism cannot be invoked while holding the k_itimer lock
because that can deadlock against the running timer callback. So the lock
must be dropped which allows the timer to be freed.
The timer free can be prevented by taking RCU readlock before dropping the
lock, but because the rcu_head is part of the 'it' union a concurrent free
will overwrite the hrtimer on which the task is trying to synchronize.
Move the rcu_head out of the union to prevent this.
[ tglx: Fixed up kernel-doc. Rewrote changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190730223828.965541887@linutronix.de
As a preparatory step for adding the PREEMPT RT specific synchronization
mechanism to wait for a running timer callback, rework the timer cancel
retry loops so they call a common function. This allows trivial
substitution in one place.
Originally-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190730223828.874901027@linutronix.de
do_timer_settime() has a 'flags' argument and uses 'flag' for the interrupt
flags, which is confusing at best.
Rename the argument so 'flags' can be used for interrupt flags as usual.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190730223828.782664411@linutronix.de
Use the hrtimer_cancel_wait_running() synchronization mechanism to prevent
priority inversion and live locks on PREEMPT_RT.
As a benefit the retry loop gains the missing cpu_relax() on !RT.
[ tglx: Split out of combo patch ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190730223828.690771827@linutronix.de
Use the hrtimer_cancel_wait_running() synchronization mechanism to prevent
priority inversion and live locks on PREEMPT_RT.
[ tglx: Split out of combo patch ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190730223828.600085866@linutronix.de
Use the hrtimer_cancel_wait_running() synchronization mechanism to prevent
priority inversion and live locks on PREEMPT_RT.
[ tglx: Split out of combo patch ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190730223828.508744705@linutronix.de
SCHED_DEADLINE inactive timer needs to run in hardirq context (as
dl_task_timer already does) on PREEMPT_RT
Change the mode to HRTIMER_MODE_REL_HARD.
[ tglx: Fixed up the start site, so mode debugging works ]
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190731103715.4047-1-juri.lelli@redhat.com
When PREEMPT_RT is enabled, the soft interrupt thread can be preempted. If
the soft interrupt thread is preempted in the middle of a timer callback,
then calling del_timer_sync() can lead to two issues:
- If the caller is on a remote CPU then it has to spin wait for the timer
handler to complete. This can result in unbound priority inversion.
- If the caller originates from the task which preempted the timer
handler on the same CPU, then spin waiting for the timer handler to
complete is never going to end.
To avoid these issues, add a new lock to the timer base which is held
around the execution of the timer callbacks. If del_timer_sync() detects
that the timer callback is currently running, it blocks on the expiry
lock. When the callback is finished, the expiry lock is dropped by the
softirq thread which wakes up the waiter and the system makes progress.
This addresses both the priority inversion and the life lock issues.
This mechanism is not used for timers which are marked IRQSAFE as for those
preemption is disabled accross the callback and therefore this situation
cannot happen. The callbacks for such timers need to be individually
audited for RT compliance.
The same issue can happen in virtual machines when the vCPU which runs a
timer callback is scheduled out. If a second vCPU of the same guest calls
del_timer_sync() it will spin wait for the other vCPU to be scheduled back
in. The expiry lock mechanism would avoid that. It'd be trivial to enable
this when paravirt spinlocks are enabled in a guest, but it's not clear
whether this is an actual problem in the wild, so for now it's an RT only
mechanism.
As the softirq thread can be preempted with PREEMPT_RT=y, the SMP variant
of del_timer_sync() needs to be used on UP as well.
[ tglx: Refactored it for mainline ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.832418500@linutronix.de
When PREEMPT_RT is enabled, the soft interrupt thread can be preempted. If
the soft interrupt thread is preempted in the middle of a timer callback,
then calling hrtimer_cancel() can lead to two issues:
- If the caller is on a remote CPU then it has to spin wait for the timer
handler to complete. This can result in unbound priority inversion.
- If the caller originates from the task which preempted the timer
handler on the same CPU, then spin waiting for the timer handler to
complete is never going to end.
To avoid these issues, add a new lock to the timer base which is held
around the execution of the timer callbacks. If hrtimer_cancel() detects
that the timer callback is currently running, it blocks on the expiry
lock. When the callback is finished, the expiry lock is dropped by the
softirq thread which wakes up the waiter and the system makes progress.
This addresses both the priority inversion and the life lock issues.
The same issue can happen in virtual machines when the vCPU which runs a
timer callback is scheduled out. If a second vCPU of the same guest calls
hrtimer_cancel() it will spin wait for the other vCPU to be scheduled back
in. The expiry lock mechanism would avoid that. It'd be trivial to enable
this when paravirt spinlocks are enabled in a guest, but it's not clear
whether this is an actual problem in the wild, so for now it's an RT only
mechanism.
[ tglx: Refactored it for mainline ]
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.737767218@linutronix.de
On PREEMPT_RT enabled kernels hrtimers which are not explicitely marked for
hard interrupt expiry mode are moved into soft interrupt context either for
latency reasons or because the hrtimer callback takes regular spinlocks or
invokes other functions which are not suitable for hard interrupt context
on PREEMPT_RT.
The hrtimer_sleeper callback is RT compatible in hard interrupt context,
but there is a latency concern: Untrusted userspace can spawn many threads
which arm timers for the same expiry time on the same CPU. On expiry that
causes a latency spike due to the wakeup of a gazillion threads.
OTOH, priviledged real-time user space applications rely on the low latency
of hard interrupt wakeups. These syscall related wakeups are all based on
hrtimer sleepers.
If the current task is in a real-time scheduling class, mark the mode for
hard interrupt expiry.
[ tglx: Split out of a larger combo patch. Added changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.645792403@linutronix.de
On PREEMPT_RT not all hrtimers can be expired in hard interrupt context
even if that is perfectly fine on a PREEMPT_RT=n kernel, e.g. because they
take regular spinlocks. Also for latency reasons PREEMPT_RT tries to defer
most hrtimers' expiry into softirq context.
hrtimers marked with HRTIMER_MODE_HARD must be kept in hard interrupt
context expiry mode. Add the required logic.
No functional change for PREEMPT_RT=n kernels.
[ tglx: Split out of a larger combo patch. Added changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.551967692@linutronix.de
The tick related hrtimers, which drive the scheduler tick and hrtimer based
broadcasting are required to expire in hard interrupt context for obvious
reasons.
Mark them so PREEMPT_RT kernels wont move them to soft interrupt expiry.
Make the horribly formatted RCU_NONIDLE bracket maze readable while at it.
No functional change,
[ tglx: Split out from larger combo patch. Add changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.459144407@linutronix.de
On PREEMPT_RT enabled kernels unmarked hrtimers are moved into soft
interrupt expiry mode by default.
While that's not a functional requirement for the KVM local APIC timer
emulation, it's a latency issue which can be avoided by marking the timer
so hard interrupt context expiry is enforced.
No functional change.
[ tglx: Split out from larger combo patch. Add changelog. ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.363363474@linutronix.de
The watchdog hrtimer must expire in hard interrupt context even on
PREEMPT_RT=y kernels as otherwise the hard/softlockup detection logic would
not work.
No functional change.
[ tglx: Split out from larger combo patch. Added changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.262895510@linutronix.de
To guarantee that the multiplexing mechanism and the hrtimer driven events
work on PREEMPT_RT enabled kernels it's required that the related hrtimers
expire in hard interrupt context. Mark them so PREEMPT_RT kernels wont
defer them to soft interrupt context.
No functional change.
[ tglx: Split out of larger combo patch. Added changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.169509224@linutronix.de
The scheduler related hrtimers need to expire in hard interrupt context
even on PREEMPT_RT enabled kernels. Mark then as such.
No functional change.
[ tglx: Split out from larger combo patch. Add changelog. ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185753.077004842@linutronix.de
hrtimer_start_range_ns() has a WARN_ONCE() which verifies that a timer
which is marker for softirq expiry is not queued in the hard interrupt base
and vice versa.
When PREEMPT_RT is enabled, timers which are not explicitely marked to
expire in hard interrupt context are deferrred to the soft interrupt. So
the regular check would trigger.
Change the check, so when PREEMPT_RT is enabled, it is verified that the
timers marked for hard interrupt expiry are not tried to be queued for soft
interrupt expiry or any of the unmarked and softirq marked is tried to be
expired in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On PREEMPT_RT not all hrtimers can be expired in hard interrupt context
even if that is perfectly fine on a PREEMPT_RT=n kernel, e.g. because they
take regular spinlocks. Also for latency reasons PREEMPT_RT tries to defer
most hrtimers' expiry into soft interrupt context.
But there are hrtimers which must be expired in hard interrupt context even
when PREEMPT_RT is enabled:
- hrtimers which must expiry in hard interrupt context, e.g. scheduler,
perf, watchdog related hrtimers
- latency critical hrtimers, e.g. nanosleep, ..., kvm lapic timer
Add a new mode flag HRTIMER_MODE_HARD which allows to mark these timers so
PREEMPT_RT will not move them into softirq expiry mode.
[ tglx: Split out of a larger combo patch. Added changelog ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185752.981398465@linutronix.de
hrtimer_sleepers will gain a scheduling class dependent treatment on
PREEMPT_RT. Use the new hrtimer_sleeper_start_expires() function to make
that possible.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hrtimer_sleepers will gain a scheduling class dependent treatment on
PREEMPT_RT. Create a wrapper around hrtimer_start_expires() to make that
possible.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hrtimer_init_sleeper() calls require prior initialisation of the hrtimer
object which is embedded into the hrtimer_sleeper.
Combine the initialization and spare a function call. Fixup all call sites.
This is also a preparatory change for PREEMPT_RT to do hrtimer sleeper
specific initializations of the embedded hrtimer without modifying any of
the call sites.
No functional change.
[ anna-maria: Minor cleanups ]
[ tglx: Adopted to the removal of the task argument of
hrtimer_init_sleeper() and trivial polishing.
Folded a fix from Stephen Rothwell for the vsoc code ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185752.887468908@linutronix.de
All callers hand in 'current' and that's the only task pointer which
actually makes sense. Remove the task argument and set current in the
function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190726185752.791885290@linutronix.de
Simplify the timerqueue code by using cached rbtrees and rely on the tree
leftmost node semantics to get the timer with earliest expiration time.
This is a drop in conversion, and therefore semantics remain untouched.
The runtime overhead of cached rbtrees is be pretty much the same as the
current head->next method, noting that when removing the leftmost node,
a common operation for the timerqueue, the rb_next(leftmost) is O(1) as
well, so the next timer will either be the right node or its parent.
Therefore no extra pointer chasing. Finally, the size of the struct
timerqueue_head remains the same.
Passes several hours of rcutorture.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190724152323.bojciei3muvfxalm@linux-r8p5
Pull parisc fixes from Helge Deller:
- Fix build issues when kprobes are enabled
- Speed up ITLB/DTLB cache flushes when running on machines with
combined TLBs
* 'parisc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Flush ITLB in flush_tlb_all_local() only on split TLB machines
parisc: add kprobe_fault_handler()
Pull preemption Kconfig fix from Thomas Gleixner:
"The PREEMPT_RT stub config renamed PREEMPT to PREEMPT_LL and defined
PREEMPT outside of the menu and made it selectable by both PREEMPT_LL
and PREEMPT_RT.
Stupid me missed that 114 defconfigs select CONFIG_PREEMPT which
obviously can't work anymore. oldconfig builds are affected as well,
but it's more obvious as the user gets asked. [old]defconfig silently
fixes it up and selects PREEMPT_NONE.
Unbreak it by undoing the rename and adding a intermediate config
symbol which is selected by both PREEMPT and PREEMPT_RT. That requires
to chase down a few #ifdefs, but it's better than tweaking 114
defconfigs and annoying users"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt, Kconfig: Unbreak def/oldconfig with CONFIG_PREEMPT=y
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXTXCMwAKCRCRxhvAZXjc
ouXAAP9JssGQT+F3OyflYy5gsERsyl/N/YeOP3LG75SYDW5SFQEAneBPUj4v2eDv
6dktofHbebzFT7VWmtFwSFwRCb5r/AM=
=6pRr
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190722' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd polling fix from Christian Brauner:
"A fix for pidfd polling. It ensures that the task's exit state is
visible to all waiters"
* tag 'for-linus-20190722' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
pidfd: fix a poll race when setting exit_state
-----BEGIN PGP SIGNATURE-----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=6yeW
-----END PGP SIGNATURE-----
Merge tag 'for-5.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fixes for leaks caused by recently merged patches
- one build fix
- a fix to prevent mixing of incompatible features
* tag 'for-5.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: don't leak extent_map in btrfs_get_io_geometry()
btrfs: free checksum hash on in close_ctree
btrfs: Fix build error while LIBCRC32C is module
btrfs: inode: Don't compress if NODATASUM or NODATACOW set
Avi Fishman