Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).
For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.
For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.
V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.
We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.
In other words:
Imagine the following case:
xrandr --output eDP1 --auto --crtc 0
xrandr --output eDP1 --off
xrandr --output eDP1 --auto --crtc 2
After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.
So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
3 changes:
- If a given value is unset, use the maximal limits from the eDP spec.
- Write back the new values, since otherwise the panel power sequencing
hw will not dtrt.
- Revert the early bail-out in case the register values are unset.
The last change reverts
commit bfa3384a9a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Apr 10 11:58:04 2012 -0700
drm/i915: check PPS regs for sanity when using eDP
v2:
- Unlock the PP regs as the very first thing. This is a required w/a
for cpu eDP on port A, and generally a good idea.
- Fixup the panel power control port selection bits.
v3: Paulo Zanoni noticed that I've fumbled the computation of the spec
limit values. Fix them up. We've also noticed that the t8/t9 values in
the vbt/bios-programmed pp are much larger than any limits. My guess
is that this is to conceal any backlight enable/disable delays. So by
using the much shorter limits from the spec, which only concerns the
sink, we risk that we might display before the backlight is fully on,
or disable the output while the backlight still has afterglow. I've
figured I don't care too much, since this will only happen when both
the pp regs are not programmed, and the vbt tables don't contain
anything useful.
v4: Don't set the port selection bits on hsw/LPT, they don't exist any
more.
v5: Fixup spelling issues in comments, as noticed by Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Register 0x42020 was defined twice under the names PCH_DSPCLK_GATE_D and
ILK_DSPCLK_GATE. This patch consolidate the 2 sets of defines in one.
The transforms done are:
PCH_DSPCLK_GATE_D -> ILK_DSPCLK_GATE_D
ILK_DSPCLK_GATE -> ILK_DSPCLK_GATE_D
DPARBUNIT_CLOCK_GATE_DISABLE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
ILK_DPARB_CLK_GATE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
DPFDUNIT_CLOCK_GATE_DISABLE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_DPFD_CLK_GATE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_CLK_FBC -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
DPFCRUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS1 -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
DPFCUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS2 -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
We have a VHRUNIT_CLOCK_GATE_DISABLE define for the pre-ILK DSPCLK_GATE_D.
Even if the same bit is used in ILK_DSPCLK_GATE_D, other bits in the
register change, so I went with re-defining it, well more precisely rename
IVB_VRHUNIT_CLK_GATE, which is not specific to IVB+. So:
IVB_VRHUNIT_CLK_GATE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE
VHRUNIT_CLOCK_GATE_DISABLE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE (ILK+ code)
This commit is only a renaming commit, further commits will clean up the
logic.
v2: Rename bit 5 and 7 to _ENABLE as setting them to 1 enables clock
gating on their respective units, contrary to all of the other bits
(Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, the DP register was used for everything. On Haswell, it
was split into DDI_BUF_CTL (which is the new intel_dp->DP register)
and DP_TP_CTL.
The logic behind this patch is based on a patch written by Shobhit
Kumar, but the way the code was written is very different.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fixup the logic error spotted by Jani Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change, but reserves 0x2 for use by userspace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the introduction of per-process GTT space, the hardware designers
thought it wise to also limit the ability to write to MMIO space to only
a "secure" batch buffer. The ability to rewrite registers is the only
way to program the hardware to perform certain operations like scanline
waits (required for tear-free windowed updates). So we either have a
choice of adding an interface to perform those synchronized updates
inside the kernel, or we permit certain processes the ability to write
to the "safe" registers from within its command stream. This patch
exposes the ability to submit a SECURE batch buffer to
DRM_ROOT_ONLY|DRM_MASTER processes.
v2: Haswell split up bit8 into a ppgtt bit (still bit8) and a security
bit (bit 13, accidentally not set). Also add a comment explaining why
secure batches need a global gtt binding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: added hsw fixup.]
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS should be setting the minimum voltage for rc6 to be 450mV. Old or
buggy BIOSen may not be doing this, so we correct it for them. Ideally
customers should update the BIOS as only it would know the optimal
values for the platform, so we leave that fact as a DRM_ERROR for the
user to see.
Unfortunately this isn't fixing any of the issues it was targeted to
fix, but it is documented that we must do it.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: bikeshedded loglevel of the "your bios is broken message" to
debug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A previous patch, namely:
commit bf97b276ca
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 11 20:42:41 2012 +0200
drm/i915: implement w/a for incorrect guarband clipping
accidentally set bit 5 in 3D_CHICKEN, which has nothing to do with
clipping. This patch changes it to be set in 3D_CHICKEN3, where it
belongs.
The game "Dante" demonstrates random clipping issues when guardband
clipping is enabled and bit 5 of 3D_CHICKEN3 isn't set. So the
workaround is actually necessary.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Oliver McFadden <oliver.mcfadden@linux.intel.com>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Problems with the previous code:
- HDMI just uses WRPLL1 for everything, so dual head cases might not
work sometimes.
- At encoder->mode_set we just write the PLL register without doing
any kind of check (e.g., check if the PLL is already being used).
- There is no way to fail and return error codes at
encoder->mode_set.
- We write to PORT_CLK_SEL at mode_set and we never disable it.
- Machines hang due to wrong clock enable/disable sequence.
So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
- Check PLL availability at ironlake_crtc_mode_set.
- Try to use both WRPLLs.
- Check if PLLs are used before actually trying to use them, and
properly fail with error messages.
- Enable/disable PORT_CLK_SEL at the right place.
- Add some WARNs to check for bugs.
The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's a copy of ironlake_set_pipeconf with 2 differences:
- There is no BPC field to set.
- The interlaced mask is now 2 bits instead of 3.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the right time is exactly after/before changing PIPE_CONF. See the
documentation about the mode set sequence.
This code is not inside any encoder-specific callback because
DDI_FUNC_CTL is part of the pipe, so it is used by all encoders.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now, we're trying to enable LCPLL at every mode set, but we're
never disabling it. Also, we really don't want to be disabling LCPLL
since it requires a very complex disable/enable sequence. This
register should really be set by the BIOS and we shouldn't be touching
it. Still, let's try to check its value and print some errors in case
we find something wrong. We're also adding intel_ddi_get_cdclk_freq
which will be used later in other places.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Workaround for a culling optimization.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Also apply to haswell, spotted by Damien.]
Reviewed-by: "Lespiau, Damien" <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't even find how I figured this might be needed anymore. But sure
enough, the value I'm reading back on platforms doesn't match what the
docs recommends.
It seemed to fix Chris' GT1 in limited testing as well.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In valleyview voltageswing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric.
Cleaned up DPLL calculations for Valleyview to support multi display
configurations.
v2: Based on Daniel's feedbacak, moved crt hotplug detect work around as separate
patch. Also moved i9xx_update_pll_dividers to i8xx_update_pll and
i9xx_update_pll.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: drop spurious whitespace changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added DPIO data lane register definitions for Valleyview
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... even if the actual infoframe is smaller than the maximum possible
size.
If we don't write all the 32 DIP data bytes the InfoFrame ECC may not
be correctly calculated in some cases (e.g., when changing the port),
and this will lead to black screens on HDMI monitors. The ECC value is
generated by the hardware.
I don't see how this should break anything since we're writing 0 and
that should be the correct value, so this patch should be safe.
Notice that on IVB and older we actually have 64 bytes available for
VIDEO_DIP_DATA, but only bytes 0-31 actually store infoframe data: the
others are either read-only ECC values or marked as "reserved". On HSW
we only have 32 bytes, and the ECC value is stored on its own separate
read-only register. See BSpec.
This patch fixes bug #46761, which is marked as a regression
introduced by commit 4e89ee174b:
drm/i915: set the DIP port on ibx_write_infoframe
Before commit 4e89 we were just failing to send AVI infoframes when we
needed to change the port, which can lead to black screens in some
cases. After commit 4e89 we started sending infoframes, but with a
possibly wrong ECC value. After this patch I hope we start sending
correct infoframes.
Version 2:
- Improve commit message
- Try to make the code more clear
Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46761
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a quick reference I'll detail the motivation and design of the new code a
bit here (mostly stitched together from patchbomb announcements and commits
introducing the new concepts).
The crtc helper code has the fundamental assumption that encoders and crtcs can
be enabled/disabled in any order, as long as we take care of depencies (which
means that enabled encoders need an enabled crtc to feed them data,
essentially).
Our hw works differently. We already have tons of ugly cases where crtc code
enables encoder hw (or encoder->mode_set enables stuff that should only be
enabled in enocder->commit) to work around these issues. But on the disable
side we can't pull off similar tricks - there we actually need to rework the
modeset sequence that controls all this. And this is also the real motivation
why I've finally undertaken this rewrite: eDP on my shiny new Ivybridge
Ultrabook is broken, and it's broken due to the wrong disable sequence ...
The new code introduces a few interfaces and concepts:
- Add new encoder->enable/disable functions which are directly called from the
crtc->enable/disable function. This ensures that the encoder's can be
enabled/disabled at a very specific in the modeset sequence, controlled by our
platform specific code (instead of the crtc helper code calling them at a time
it deems convenient).
- Rework the dpms code - our code has mostly 1:1 connector:encoder mappings and
does support cloning on only a few encoders, so we can simplify things quite a
bit.
- Also only ever disable/enable the entire output pipeline. This ensures that
we obey the right sequence of enabling/disabling things, trying to be clever
here mostly just complicates the code and results in bugs. For cloneable
encoders this requires a bit of special handling to ensure that outputs can
still be disabled individually, but it simplifies the common case.
- Add infrastructure to read out the current hw state. No amount of careful
ordering will help us if we brick the hw on the initial modeset setup. Which
could happen if we just randomly disable things, oblivious to the state set up
by the bios. Hence we need to be able to read that out. As a benefit, we grow a
few generic functions useful to cross-check our modeset code with actual hw
state.
With all this in place, we can copy&paste the crtc helper code into the
drm/i915 driver and start to rework it:
- As detailed above, the new code only disables/enables an entire output pipe.
As a preparation for global mode-changes (e.g. reassigning shared resources) it
keeps track of which pipes need to be touched by a set of bitmasks.
- To ensure that we correctly disable the current display pipes, we need to
know the currently active connector/encoder/crtc linking. The old crtc helper
simply overwrote these links with the new setup, the new code stages the new
links in ->new_* pointers. Those get commited to the real linking pointers once
the old output configuration has been torn down, before the ->mode_set
callbacks are called.
- Finally the code adds tons of self-consistency checks by employing the new hw
state readout functions to cross-check the actual hw state with what the
datastructure think it should be. These checks are done both after every
modeset and after the hw state has been read out and sanitized at boot/resume
time. All these checks greatly helped in tracking down regressions and bugs in
the new code.
With this new basis, a lot of cleanups and improvements to the code are now
possible (besides the DP fixes that ultimately made me write this), but not yet
done:
- I think we should create struct intel_mode and use it as the adjusted mode
everywhere to store little pieces like needs_tvclock, pipe dithering values or
dp link parameters. That would still be a layering violation, but at least we
wouldn't need to recompute these kinds of things in intel_display.c. Especially
the port bpc computation needed for selecting the pipe bpc and dithering
settings in intel_display.c is rather gross.
- In a related rework we could implement ->mode_valid in terms of ->mode_fixup
in a generic way - I've hunted down too many bugs where ->mode_valid did the
right thing, but ->mode_fixup didn't. Or vice versa, resulting in funny bugs
for user-supplied modes.
- Ditch the idea to rework the hdp handling in the common crtc helper code and
just move things to i915.ko. Which would rid us of the ->detect crtc helper
dependencies.
- LVDS wire pair and pll enabling is all done in the crtc->mode_set function
currently. We should be able to move this to the crtc_enable callbacks (or in
the case of the LVDS wire pair enabling, into some encoder callback).
Last, but not least, this new code should also help in enabling a few neat
features: The hw state readout code prepares (but there are still big pieces
missing) for fastboot, i.e. avoiding the inital modeset at boot-up and just
taking over the configuration left behind by the bios. We also should be able
to extend the configuration checks in the beginning of the modeset sequence and
make better decisions about shared resources (which is the entire point behind
the atomic/global modeset ioctl).
Tested-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Acked-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add some macros to make the pipe computation a bit easier.
v2: I've mixed up the CPT and !CPT PORT_TO_PIPE macro variants ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"New stuff for -next. Highlights:
- prep patches for the modeset rework. Note that one of those patches
touches the fb helper in the common drm code.
- hasw hdmi audio support (Wang Xingchao)
- improved instdone dumping for gen7 (Ben)
- unbound tracking and a few follow-up patches from Chris
- dma_buf->begin/end_cpu_access plus fix for drm/udl (Dave)
- improve mmio error reporting for hsw
- prep patch for WQ_NON_REENTRANT removal (Tejun Heo)
"
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (41 commits)
drm/i915: Remove __GFP_NO_KSWAPD
drm/i915: disable rc6 on ilk when vt-d is enabled
drm/i915: Avoid unbinding due to an interrupted pin_and_fence during execbuffer
drm/i915: Use new INSTDONE registers (Gen7+)
drm/i915: Add new INSTDONE registers
drm/i915: Extract reading INSTDONE
drm/i915: Use a non-blocking wait for set-to-domain ioctl
drm/i915: Juggle code order to ease flow of the next patch
drm/i915: Use cpu relocations if the object is in the GTT but not mappable
drm/i915: Extract general object init routine
drm/i915: Protect private gem objects from truncate (such as imported dmabuf)
drm/i915: Only pwrite through the GTT if there is space in the aperture
i915: use alloc_ordered_workqueue() instead of explicit UNBOUND w/ max_active = 1
drm/i915: Find unclaimed MMIO writes.
drm/i915: Add ERR_INT to gen7 error state
drm/i915: Cantiga+ cannot handle a hsync front porch of 0
drm/i915: fix reassignment of variable "intel_dp->DP"
drm/i915: Try harder to allocate an mmap_offset
drm/i915: Show pin count in debugfs
drm/i915: Show (count, size) of purgeable objects in i915_gem_objects
...
There was some merge conflicts in -next and they weren't so pretty, so
backmerge now to avoid them.
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_modes.c
INSTDONE is used in many places, and it varies from generation to
generation. This provides a good reason for us to extract the logic to
read the relevant information.
The patch has no functional change. It's prep for some new stuff.
v2: move the memset inside of i915_get_extra_instdone (Jani)
v3,4: bugs caught by (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ERR_INT on HSW will display unclaimed MMIO accesses. This can be either
the result of a driver bug writing to an invalid addresses, or the
result of RC6.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ERR_INT can generate interrupts. However since most of the conditions seem
quite fatal the patch opts to simply report it in error state instead of
adding more complexity to the interrupt handler for little gain (the
bits are sticky anyway).
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use _PIPE macro to get correct register definition for IBX/CPT, discard
old variable "i" way.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Added the DIP_PORT_SEL #define from a preceeding patch in the
series that needs more work.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They've changed it ... for no apparent reason. Meh.
V2: remove unused 'is_hsw' field.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By looking at the current way we're using these definitions I don't
think this commit will fix any bug, but programmers from the future
are evil and will certainly find ways to combine macro expansion with
operator precedence to introduce bugs that are hard to find.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the only part of the i915_reg.h file that looks totally wrongly
indented, so I assume my editor config is the correct one.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Correctly erase the values previously set and also check for 6bpc and
10bpc.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During my tests, everything worked even if the wrong polarity was set.
Still, we should try to set the correct values.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mask the value before changing it and also select DVI when needed.
DVI was working in cases where the BIOS was setting the correct value
because we were not masking the value before changing it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Basic context support on HSW is no different than previous generations.
The size of the context object changes, but that's about it.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the base addresses shifting around, this is easier to handle.
Also move to the real reg offset on vlv.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interface's immediate purpose is to do synchronous timestamp queries
as required by GL_TIMESTAMP. The GPU has a register for reading the
timestamp but because that would normally require root access through
libpciaccess, the IOCTL can provide this service instead.
Currently the implementation whitelists only the render ring timestamp
register, because that is the only thing we need to expose at this time.
v2: make size implicit based on the register offset
Add a generation check
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: fixup the ioctl numerb:]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Splitting them up between pch and gmch variants just makes it harder
to find things. Especially since the hotplug bits are actually valid
on earlier chips, too.
v2: Fixed the comment as pointed out by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I so totally suck.
This can cause a black screen if (for whatever reason) the bios
hasn't set this bit itself.
This regression has been introduced in
commit 7cf4160148
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 5 10:07:09 2012 +0200
drm/i915: clear up backlight #define confusion on gen4+
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having had to dive into the bspec to understand what each stage of the
workaround meant, and how that the ring broadcasting IDLE corresponded
with the GT powering down the ring (i.e. rc6) add comments to aide
the next reader.
And since the register "is used to control all aspects of PSMI and power
saving functions" that makes it quite interesting to inspect with
regards to RC6 hangs, so add it to the error-state.
v2: Rediscover the piece of magic, set the RNCID to 0 before waiting for
the ring to wake up.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There were some fields missed. Daniel pointed this out in review, and I
know I fixed it, but something happened somehow and some time.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
*sigh* the docs had it spelled wrong, corrected it, and then proceeded
to re-do the original error. The original code preserved this history,
and this patch attempts to keep in sync with the current docs.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required for a stable FDI connection.
v2: fix and simplify the FDI_RX_MISC bits as noticed by Paulo Zanoni.
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The tileoffset register only supports a limited offset in x/y of 4096,
so for giant screen configuration with a shared fb we wrap around.
Fix this by computing a linear offset in tiles (pages) and only use
the tileoffset register to offset within the tile.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid recomputing the display framebuffer offset on gen2/3
pageflips. This is also prep work to do similar trickery on gen4+
Also:
- kill "Start", such upper-case remnants from the ddx must surely die.
- rename "Offset" to linear_offset, to make it clearer that on gen4+
this is only used by the hw for linear buffers, for tiled buffers it
uses the TILEOFF register.
- call DSAPADDR DSPLINOFF on gen4+ for the same reason (and because
the documentation really renamed the register).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
